Search Documents

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961

By Kung-Lee Wang

The 1963 performance of the United States economy was impressive. The year was one of continued growth unmarred by a recession. By the end of 1963 the economy's expansion had already lasted almost as long as the 1954-57 upswing, and the net gain in output since the trough in activity in early 1961 compared favorably with most earlier postwar cyclical advances. There was no indication of any slow- down at yearend. Both gross national product (GNP) and national income in 1963 were 5 percent higher than in the previous year. GNP totaled $584 billion, a gain of $28 billion over 1962. Real output of goods and services rose 3.4 percent over the year. Price increases continued to be moderate. Production, employment, personal income, and corporate profits all registered new but unemployment continued high at 5.5 percent and the prospects for improvement remained poor. The economy again failed to use its full potential. Current value of mineral production kept pace with the economy. The constant dollar value of mineral production gained more than real GNP because of the relatively stable price of minerals. Mining production achieved a new high in 1963. Steel production totaled 110 million tons, 12 million tons above 1962, making 1963 the first 100- million-ton year since 1957 and lifting the steel-associated minerals group upward. The gain in ferrous metals mining was insufficient to compensate for the decline of nonferrous metals mining resulting in an insignificant decline in the metal mining total as a whole. The upsurge of construction material minerals output, with an assist from chemical and fertilizer minerals, accounted for peak production of

Jan 1, 1964

By C. P. Mangelsdorf

This report deals with the efforts to develop a portable device suitable for underground use for the purpose of measuring the frequency of vibration of the horizontal chords of Birmingham roof trusses. Four devices are investigated and evaluated. An approximate emperical expression developed from a mathematical analysis provides a means of converting the frequency into tension. The method appears to be effective in mines with shale roof but requires some modification for other roofs.

Jan 1, 1983

By John J. McClelland

The Bureau of Mines conducted a study of longwall plow operations to identify dust sources and existing control technology. Three longwalls employing either the high-speed overtaking or conventional method of mining were surveyed. Principal operating parameters and on-site dust control technology at the time of each survey are described. Short-term gravimetric and instantaneous sampling results are discussed in detail. The relationship between longwall dust levels and dust control technology was examined.

Jan 1, 1988

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By Kathleen J. D?Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has invented a laboratory apparatus for continuous separation of minerals based on differences in dielectric properties. The separator consists of a rotating drum electrode and a wire screen electrode positioned 3 mm apart. A high voltage applied across the electrodes that are immersed in a dielectric fluid produces a high-gradient electric field. The high-dielectric-constant (K) minerals are attracted to and conveyed through the separator by the rotating drum electrode, while the low K minerals settle through the screen electrode. Several design and operating parameters, such as electrode configurations, the dielectric liquid and its dielectric constant, electrical voltage and frequencies, feed rates, and particle sizes were studied. In addition, 28 different mineral mixtures were tested with the dielectric separator. In typical tests, a sample of rutile and quartz gangue containing 10-percent rutile was concentrated to 62-percent rutile with 94-percent rutile recovery. A second-stage dielectric separation of the rutile concentrate produced a 92-percent-rutile concentrate. The overall rutile recovery for the two-stage dielectric separation was 86 percent.

Jan 1, 1980

By C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By Nicholas P. Kripakov

The U.S. Bureau of Mines examined the applicability of existing material models to solve practical geotechnical mining-related problems by solving a yielding pillar stability problem considering confining effects on strength. Numerical difficulties normally encountered with modeling strain softening behavior were eased with a simplified computational procedure using a quasi-elastic approach to account for residual strength after initial failure. Although in agreement with a confined-core pillar design method using actual mine conditions that include mine layout geometry, overburden geology, and rock properties of the deposit and surrounding structure, the results cannot be verified because measured field data are not available at this writing.

Jan 1, 1981

By R. O. Kneisley

Rock mechanics measurements indicate that the present two-bed mine design used at the Big Island trona mine, Green River, Wyo., results in stable workings. Vertical pressure changes in the lower panel pillars and horizontal pressure changes in the lower bed roof and floor indicated negligible upper bed mining influence. Pillar stresses stabilized soon after upper bed mining was completed. Strata movements in the pillar ribs, roof, and floor were also negligible and stabilized soon after completion of upper bed mining. Using tributary area theory, the confined core approach, and studies of model trona pillars it is shown that increased extraction ratio is possible. A program of gradually increased extraction ratio accompanied by simple measurements should result in a mine design that includes both higher recovery and long-term stability.

Jan 1, 1981

By D. R. Tesarik

An instrumentation and numeric modeling study was conducted by the Bureau of Mines at the Magmont Mine in Bixby, MO. An isolated section of this room-and-pillar mine was monitored with borehole and closure extensometers during a pillar recovery program to determine stress redistribution. In situ stress measurements were taken in the rib before pillar extraction began. Sample cores from the boreholes were taken for analysis of the properties of the host rock in the laboratory. The extensometers recorded no measurable displacements during most of the operation. Two-dimensional, finite-element; three-dimensional, finite-element; and three-dimensional displace-ment discontinuity codes were used to model the area of study. The finite-element models were run with two initial stress conditions, i.e., stress due to gravity only and stress obtained by in situ measurements. Horizontal stresses in the models reduced the calculated factor-of-safety in the mine back by up to a factor of 10, but did not have a significant effect on calculated pillar stability.

Jan 1, 1989

By M. D. Marshall

This handbook is for the engineer or person responsible for the storage and removal of material from bins and silos in the minerals industry. The objective of the handbook is to prevent bin-related accidents by eliminating problems which require workers to enter bins. It provides basic information on handling materials so that knowledgeable decisions can be made on bin design and accessories to minimize flow stoppages. Materials are classified in terms of their flowability, and bin design and accessories suggested for each classification. A method for classifying a material is also given, and the various types of material flow aids reviewed. Safety around bins is the basic theme of the handbook. Federal regulations are reviewed and additional suggestions presented to prevent bin accidents. New equipment for releasing material hang-ups is reviewed.

Jan 1, 1984

By Noel N. Moebs

Coal mine roof failure is categorized according to character, trend, or pattern of occurrence. Two principal categories of failure are proposed--geology related and stress related. Geology-related failure includes both lithology and structure. Each of several subcategories reflects the probable cause of failure and thereby provides a basis for the selection of appropriate techniques for reducing the incidence of failure. These control techniques, depending on local conditions, may include supplementary support, destressing, reduction of mine air humidity, or a change in the customary support methods.

Jan 1, 1986

By M. M. Fine

A satisfactory mean: of beneficiating a Brazilian phosphate rock was developed in a mineral-dressing-research study by the Bureau of Mines. High-grade concentrates well ever the specified minimum grade of 70 percent tricalcium phosphate, were produced, with goad recoveries by agglomerate tabling and flotation. A lower gads but usable secondary product was recovered by sedimentation of the minus-200-mesh fraction of the ore. The ore wan representative of an extensive deposit recently discovered near Recife in the State of Pernambuco, Brazil, which will be exploited in a plant planned to eventually produce at the rate of 500,000 tons of concentrate annually. Although Brazil has been reported to Lave a substantial reserve of phosphate rock,3/ the country has never been more than a small producer of this commodity. From 1945 to 1950 the highest production of phosphate rock attained in Brazil amounted to 10,421 tons. Production in 1949, the most recent year for which figures are available, was 4,553 tons.4/

Jan 1, 1954

By Ryan G. Wade, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

By R. P. Beyer

As part of its thermodynamic investigations of mineral compounds, the Bureau of Mines has written an algorithm based on Newton's method for solving for the characteristic Debye temperature of a compound, from heat capacity and temperature data. A listing of a FORTRAN IV program based on this algorithm, for calculating Debye temperatures given heat capacities or for calculating heat capacities given Debye temperatures, is available from the author upon request.

Jan 1, 1981

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract I for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 11, 1976

By James L. Hendrix

A study was made of the United States Bureau of Mines' chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and IT mechanisms involved in the reactions betweens sphalerite, and galena with chlorine. The influence of copper on the extraction rates was also studied. It has been shown the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373K with the rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1980

By F. S. Crawford

Untreated timber in a mine or elsewhere may fail prematurely because it may "rot out before it wears out." If such timber is treated with a satisfactory preservative, decay will be retarded for many years, and it's serviceable life will beg prolonged to several times that usually obtained from untreated timber.4/ Treated timber has many advantages, and although it has been used extensively by railroads and other large consumers of structural timber, the relatively small use in mines seems strange indeed. Timber does not decay if it is kept dry, cool, and well-ventilated or if it is kept constantly wet or sumberged in water. At a mine in Canada the temperature in the upper levels was only 44° F., and the timber did not decay. As operations deepened, however, warmer ground was opened, and, with high humidity, conditions favored timber decay. The life of untreated timber may be only 2 to 3 years under such conditions.

Jan 1, 1951

By Fun-Den Wang

A two-dimensional plane strain analysis by the stiffness matrix method was used to analyze two basic pit slope configurations. The magnitudes and the directions of stresses are given for a V-shape and for a flat-bottom pit with the slope angle varying from 30° to 90° at 10° intervals, Stress effects due to irregular pit configuration or to in-situ forces are discussed. Equations of similitude for gravity loading are given. Expressions are also given for the stresses at the toe as a function of slope angle. Procedures are given for finding the stresses in any geometrically similar pit slope of different dimensions and material properties from the stresses and equations presented in this report. Numerical results show that the V-shape pit slopes have lower stresses than the flat-bottom pit slopes; hence, they are inferred to be more stable.

Jan 1, 1970