Search Documents

By D. A. Paice, A. B. Shimp

Illegitimate loads on a mine dc power distribution system can be detected by measuring a superimposed ac current. To implement such a scheme, a 10-volt, 3-kHz voltage is applied at each dc power substation. By this means, the mine dc power distribution network, consisting of a feeder and trolley wires with a grounded rail return, is caused to serve also as a 3-kHz ac distribution network.

Jan 1, 1975

By J. Roger Loebenstein

Demand for arsenic exceeded supply in 1980, and the major domestic and foreign producers allocated available supplies to customers. Major demand was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-In June 1980, the Environmental Protection Agency (EPA) listed inorganic arsenic as a hazardous air pollutant.2 Proposed regulations on arsenic emissions were to be announced on an industry-by-industry basis at a future date, and public comment on the listing and on specific regulations was to be heard.

Jan 1, 1981

By W. H. Engelmann

The electrokinetic (zeta) potentials of a charcoal granite in an aluminum chloride (AlCl3) solution and in an oleylanunonium acetate (C18H35NH3+ -OCOCH3) solution have been correlated with the specific damping values as measured by the pendulum sclerometer. This investigation shows that the pendulum specific damping attains a minimum at the isoelectric point for the charcoal granite-aluminum chloride and charcoal granite-oleylammonium acetate systems, and thus indicates that the penetration of the diamond points is a maximum at the isoelectric point.

Jan 1, 1967

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992

By R. W. Freedman

The Bureau of Mines has developed a gas chromatographic method for the rapid and accurate determination of oxygen, nitrogen, carbon dioxide, methane, and, if present, carbon monoxide in mine air. This method replaces such presently used gas-reaction types as the Haldane or Orsat analysis, offering advantages in terms of precision, accuracy, speed, and convenience.

Jan 1, 1968

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

To monitor the quantity and quality of air in underground mines to assure safe working conditions. Approach Several mine air monitoring systems, consisting of sensing stations in the return airways and control stations on the surface, have been Installed and tested. How It Works Sensor stations are located at strategic places in the underground mine. At each station, the sensors measure air velocity, air temperature, methane concentration, and carbon monoxide concentration. In one system, differential air pressure between intake air and return air, is also measured. Output voltages of the sensors are converted to digital signals at the sensor stat ion; these signals are multiplexed so that data from all sensors can be trans-phone wire to a central station. There the data are displayed and alarms are triggered when the sensed values exceed (or in the case of air velocity, fall below) a preset value. In addition to receiving data automatically, the central station can poll individual sensors at any time.

Jan 1, 1978

By E. J. Kloos

Bureau of Mines-approved self-contained breathing apparatus of the compressed air demand type were evaluated for performance at low temperature. Apparatus durations, breathing resistances, and airflow rates were measured on machine tests at room temperature and -25° F. Man tests under actual wearing conditions verified the machine test results. Many serious functional changes in apparatus performance occurred at low temperature. Pressure regulators malfunctioned when diaphragms lost flexibility. Under certain conditions frozen condensed moisture sealed exhalation valves and fogged eyepieces. High-pressure leaks, not encountered at ordinary temperature, developed at low temperature. Tests results are discussed generally and specifically for each apparatus. Recommendations are given to obtain optimum performance from demand type breathing apparatus at low temperatures.

Jan 1, 1968

Develop a user-friendly, personal computer-based numerical modeling program that performs structural analyses of underground tabular deposits, making these readily available to the mining industry. Background When ore is extracted from an underground mine, the overburden weight is redistributed to unmined areas, recompacted gob zones, and artificial structures such as packwalls and/or cribs. This redistribution of stresses continually changes throughout the mining cycle and can be especially complicated when multiple-seam mining is involved. Numerical mine structural analysis methods provide a way of calculating the redistribution of overburden stresses and the resulting loading for any given area of an underground mine, thus enabling engineers to design safer and more productive mines. In 1973 Crouch and Fairhurst developed a mine structural analysis computer program called MINSIM. This computer program was based on the three-dimensional displacement-discontinuity approach, a subvariation of the boundary-element method. In 1979 Sinha expanded MINSIM's capability to provide an analysis of parallel multiple seams. Sinha called his program MULSIM. During 1984 and 1985, the Bureau of Mines upgraded and completely restructured MULSIM into what is now called MULSIM/BM.

Jan 1, 1990

Reduce dust generated during bagging at minerals processing facilities, such as silica sand operations. Approach Installation of a new type of bag nozzle system eliminates the major dust sources during the bag filling process. How It Works The drawing illustrates components of the new bag nozzle system. The system differs in several ways from the conventional nozzle system. An improved bag clamp reduces the amount of blow-back during bag filling, because it has direct contact with approximately 80 per-cent of the nozzle. A two nozzle arrangement includes an inner or "fill" nozzle surrounded by another nozzle, which is designed to exhaust excess pressure from the bag after it has been filled. The exhaust is powered by an eductor, which uses a venturi effect to exhaust the bag at approximately 50 cfm. The exhaust exits into a bucket elevator and is recycled. A pinch valve automatically opens and closes the exhaust system to the bag.

Jan 1, 1984

By Harry E. Tuff

"This paper is based data obtained by the Bureau of Mines from some of the principal mine operators in Pennsylvania, in the course of a study conducted in cooperation with the U. S. Forest Service, with regard to economies that might be effected in the selection storage, and preparations of timber particularly treatment with preservative to prolong its life.The Pennsylvania anthracite region, considered as a single mining district is by far the largest user of mine timber of any mining district, either coal or metal, in the United States, and the bituminous districts of Pennsylvania rank second. The present annual consumption of mine timber by the coal-mining industry of Pennsylvania probably exceeds 100,000,000 cubic feet annually.In 1919, Pennsylvania produced, in round figures, 145,300,000 tons of bituminous coal, 86,200,000 tons of anthracite, and 5,400,000 tons of iron ores. If it be assumed that the bituminous coal mines required 0.33 cubic feet, anthracite mines 0.7, and iron mines 0.9 cubic feet per ton mined the timber requirements were bituminous. 47,950,000; anthracite, 60,340,000; iron mines, 4,860,000 or a total of over 113,000,000 cubic feet.The average cost of round mine timber in the anthracite region in 1905, was, according to the U. S. Forest Service, 6.6 cents per cubic foot, and $15.00 per 1000 board feet for sawed timber. The present cost Las advanced to 27.5 cents per cubic foot for round timber, delivered to the mine, of which cost 57.4, represents freight charges."

Nov 1, 1923

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By Martyn F. Roetter

The work of the operational communication systems' group dealt with a range of communication needs and functions within mines, primarily along haulageways, to and within sections up to the working face itself, and in mine shafts. A mixture of communication techniques and hardware is needed to satisfy this variety of communication needs within the differing environments encountered in U.S. mines. Substantial progress, both experimental and theoretical, has been made in recent years towards developing alternative communication systems suitable for use in mines which are based on "guided" waves, including wire-less (waveguide-like propagation in mine tunnels) and wire-based systems (leaky coaxial cables or wires) . Major priorities identified for further work needed to confirm (or deny) the applicability, and refine the operational specifications of promising communication systems for mine use include: Short-Term Projects o Cost/performance analyses of promising leaky coaxial cable and UHF radio communication systems which require further data from: - Experimental investigation under U.S. mine conditions of the performance of potentially applicable leaky coaxial cable communication systems developed in Europe (France, Belgium, and the U.K). - Cost estimates on these coaxial cable communication systems. - Measurements of UHF radio propagation in low-coal mines. - Investigation of the influence of obstacles (e.g. shuttle cars and section machinery) in the entries on UHF radio propagation in mines. o Investigation of the problems of transmitter and receiver coupling and termination matching associated with the two-way propagation of low frequency radio waves in hoist shafts.

Jan 1, 1973

By Gerald J. Joy, Paul J. Middendorf

This study examines the patterns and trends in noise exposure documented in data collected by Mine Safety and Health Administration inspectors at U.S. coal mines from 1987 through 2004. During this period, MSHA issued a new regulation on occupational noise exposure that changed the regulatory requirements and enforcement policies. The data were examined to identify potential impacts from these changes. The overall annual median noise dose declined 67% for surface coal mining and 24% for underground coal mining, and the reduction in each group accelerated after promulgation of the new noise rule. However, not all mining occupations experienced a decrease. The exposure reduction was accompanied by an increase of shift length as represented by dosimeter sample duration. For coal miners exposed above the permissible exposure level, use of hearing protection devices increased from 61% to 89% during this period. Participation of miners exposed at or above the action level in hearing conservation programs rapidly reached 86% following the effective date of the noise rule. Based on inspection data, the occupational noise regulation appears to be having a strong positive impact on hearing conservation by reducing exposures and increasing the use of hearing protection devices and medical surveillance. However the increase in shift duration and resulting reduction in recovery time may mitigate the gains somewhat.

To reduce needless paging of persons by all phones in a mine or mill, while retaining all-location page capability. Approach Standard pager phones of any manufacturer are modified to include the option of selective calling and message holding. How It Works All commercial mine pager phones presently rely upon voice paging via a loud-speaker. When a page is initiated, every phone in the system broadcasts the audible voice page, even phones in locations where the desired person could not possibly be. The advantage of this scheme is that whole-mine paging occurs. The disadvantage is that persons soon begin ignoring pages because they occur all the time, and most are for someone else. Also, it requires considerable battery power from all phones making it necessary to change batteries very frequently, even in phone locations where personnel rarely go. In addition, if a voice page is made and not heard, there Is no way to leave the message. Therefore, persons who at a later time come near a phone, have no way of knowing a page was made and was not acknowledged. This results in situations that often have a direct bearing on safety and productivity.

Jan 1, 1980

Provide an economic alternative to drill-blast excavation with the same ability to excavate openings of varied orientation, shape, and size. Approach Develop an efficient, adaptable, mechanical excavation machine that produces unconfined tensile failure in rock. How It Works A drill-split fragmentation machine that combines a drill and a unique splitter has been developed. The drill and splitter are mounted on a carriage that positions the splitter in a hole immediately after it is made by the drill. The splitter creates force loads that cause the rock to fragment, and the process is repeated for excavation. The unique splitter applies both radial and axial loads to the rock mass, which produces an excavation action comparable to pulling a plug. This excavation action distinguishes the radial-axial splitter from typical demolition splitters, which require a free surface parallel to the axis of the splitter toward which to break rock.

Jan 1, 1989

Reliably detect fires by sensing sub-micrometer-sized particles released into the air by smoldering or burning materials. Approach An extremely sensitive, ionization-type fire detector has been built that continuously draws air samples through its ionizing field and collects the ionized smoke particles downstream, thereby generating a proportional electrical output signal. (An offshoot instrument measures the size distribution and number of sub-micrometer particles in air.) How It Works Mine air to be monitored is drawn through the instrument assembly by a small pump. A pre-filter and cyclone remove dust particles and other particles larger than 0.6 micrometer diameter. The air and remaining aerosol-sized particles flow through a gastight tube which contains the detector. See diagram. Smoke and other sub-micrometer-size particles moving Into the detector, pass through an Ionizing field, and are struck by alpha particles released from radioactive source located on the axis of the tube, The alpha particles move radially outward until they strike smoke particles or molecules of air or water. When struck, a smoke particle or molecule loses an electron and becomes positively ionized.

Jan 1, 1979

By Charles L. Kimbell

Annual global steel industry investment is partly mirrored in the data for selected market economy countries that appear in table 13 for 1988-90. No reasonably comprehensive 1991 data were available for inclusion in this study, and the partial reporting available was so incomplete that it was impossible to demonstrate whether the level advanced or declined from the 1990 level of nearly $15.5 billion. Moreover, with the radical changes that are now being effected in the steel industries of the states that were the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available. Updated information on market economy country petroleum industry capital and exploration expenditures by geographic area has been included in table 14, and it is evident that there was a substantial upturn in investment in 1991. The level of almost $74.5 billion was 14.5 % above the 1990 level and included gains in every topical category and geographic area. The source of information for this table has been changed to the Oil and Gas Journal Database from the previously used Chase-Manhattan Bank study of Capital Investments of the World Petroleum Industry, which has been discontinued. Because of this source change, it has been necessary to modify the structure of the table somewhat, but its total scope of coverage is regarded as basically unchanged. It should be noted that the grand total, as well as some of the detail appearing for 1987, corresponds precisely with those in the previous source.

Jan 1, 1993

By D. Montagna

Large quantities of zinc-base die-cast scrap containing 3 to 4 percent aluminum are presently refined by mixing with other secondary zinc products such as galvanizer dross and distilling in a retort. The Bureau of Mines investigated alternate aluminum removal processes utilizing low-cost fluxes. Basing the investigation on the metallurgical principle that a reactive impurity can be removed from a less reactive matrix metal by melting under a flux consisting of a salt or oxide of a metal less reactive than the impurity, three separate flux mixtures were studied. In the first flux system, [FeCl3] + NaCI (the active component is underlined), part of the aluminum is' eliminated by the formation of volatile aluminum chloride and the rest by the creation of a high melting point iron-aluminum intermetallic compound that can be separated from the remaining molten zinc by filtration. Aluminum removal in the second system, [Fe203] + CaClz + NaCI, is effected by the formation of the iron-aluminum compound and possibly aluminum oxide. The third system, spent sal skimmings--essentially a mixture of [ZnCl2], NH4Cl, and ZnO, depends solely on aluminum chloride formation. Of the three flux systems investigated, the best results obtained were with system 3. Aluminum was reduced in the molten die-cast alloy from 4.10 percent to 0.01 percent when depleted sal skimmings were used.

Jan 1, 1969

By Stephen C. Tadolini, Thomas M. Barczak

An underground investigation was designed and implemented by the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of pre-driven longwall recovery rooms supported with pumpable concrete roof supports. The pumpable roof supports were instrumented with hydraulic pressure cells to measure support loading. Displacement of the support was also measured to assess the support reaction to ground movements. Movement up to 12.5 m (40 ft) into the roof was measured with sonic probes and multipoint extensometers. Borehole pressure cells were installed in the panel fender and outby pillars to evaluate load transfer. Shield loading was also assessed to determine the impact of the panel fender yielding on face loading. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 3.12 m (10 ft) from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 15-20 cm (6-8 inches) once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 10 m (32 ft) horizon with total deformation ranging from five to 10 cm (2 to 4 inches), indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in instabilities that can lead to catastrophic results. Understanding the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields is providing valuable information for the refinement of the NIOSH Ground Reaction Curve for standing and intrinsic roof support system design.