Search Documents

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill's machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill's ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

Prevent the explosion of methane gas or coal dust by replacing air with inert gas inside highwall mine excavations. Approach Use combustion gases as a source of inert gas with low oxygen content to blanket the cutting, head of highwall mining machines. This gas is placed strategically at the collar of the excavation where it enters the hole to replace the mined coal volume. The elimination of oxygen from the hole prevents explosions of gas or dust. How It Works Highwall mining methods arc used when surface mining becomes uneconomical. One method of highwall mining involves use of a horizontal auger to enter the coalbed from a surface mine bench. The coal is mined in a series of horizontal, parallel, and large-diameter holes. Historically, little methane has been associated with auger mining. However, mining technology has extended the reach of auger mining, which can increase the occurrence of methane. Methane explosions at auger mining operations have been increasing. Methane has been the primary fuel source of these ignitions, but coal dust also may have been involved.

Jan 1, 1993

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

The dust exposure of the longwall shearer operator is usually determined by his position relative to the cutting drums. The dust generated during cutting may travel up-wind, against the primary airflow, and be carried out into the walkway where it can contaminate the intake air for as much as 10 feet outby the shearer operator's controls. Thus, both head and tail drum operators are exposed to un-acceptably high levels of air-borne respirable dust. One Solution The latest generation of long-wall shearers has features that make the use of radio remote or umbilical (hard wire) remote control relatively easy to implement. Remote control can enable shearer operators to control machines from positions that are less dusty than normal control stations. With either type, the head-drum operator can now control the shearer from a position up to 20 feet on the intake-air side of the shearer, while the tail-drum operator's station is now located across from the head drum.

Jan 1, 1984

"Minimizing Particle Contamination During Generation of Fresh Dust for Inhalation Studies J. Abraham, MS, Mechanical and Aerospace Engineering, West Virginia University, 1995Correlating Lung Crackle Using Holographic Interferometry Ali Afshari, MS, West Virginia University, 1989Effect of Bit Wear on Dust Generation Mudassar Ahmad, MS, West Virginia University, 1992 The Effect of Surfactants on Suppression of Non-Wettable Particles Ali Alaboyun, MS, Mineral Engineering, The Pennsylvania State University, 1989 Geochemical Characterization of Kerogens, Shales, and Coal Refuse Associated with Allegheny Formation of Cases of Northern West Virginia Dick Andre, MS, West Virginia University, 1987Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment Indranil R. Bardhan, MEM Report, The Pennsylvania State University, 1992Size and Mass Characterization of Airborne Particulate Matter in Underground Coal Mines Using Diesel-Powered Equipment I. Bardhan, R. V. Ramani, and J.M. Mutmansky, Mining Engineering, The Pennsylvania State University, University Park, PA, Final Report to the U.S. Bureau of Mines, April, 1994Particle Concentrations in a Hazelton Inhalation Chamber Shahram Bavani, MS, West Virginia University, 1985Use and Potential of Lazer Holographic Interferometry and Subsidence Model- Study of an Underground Room and Pillar Mine Richard Begley, MS, West Virginia University, 1984Development of a Mechanistic Model for Prediction of Subsidence in a Longwall Mine Richard Begley, PhD, West Virginia University, 1990Redesign of Micro-Orifice Uniform Deposit Impactor Steve Behm, MS, University of Minnesota, 1991Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle, MS, The Pennsylvania State University, 1996Evaluation of a Two-Phase Spray System for Dust Suppression B. Belle and R.-V. Ramani, The Pennsylvania State University, University Park, PA, Final Report, September 9, 1996A Fracture Mechanics Study of Crack Propagation Mechanism in Coal: The Mechanics of Fine Fragment Formation Z.T. Bieniawski and R. Karl Zipf, Jr., Mining Engineering Department, The Pennsylvania State University, University Park, PA. Final Report, October l, 1988A Mathematical Model for the Prediction of Ambient Dust Concentrations in Mine Atmospheres R. Bhaskar, MS, Mining Engineering and Operations Research, The Pennsylvania State University, 1984Spatial and Temporal Behavior of Dust in Mines-Theoretical and Experimental Studies –R. Bhaskar, PhD, Mining Engineering, The Pennsylvania State University, 1987"

Jan 1, 1998

By L. C. IlsLey

It is most unfortunate that a few must often suffer , and perhaps die , that many may benefit from a fuller appreciation of the dangers surrounding mining operations , and the proper use of safeguards designed to offset these dangers . This has been the case during the last few months in the anthracite field , where several explosions , resulting in burnings and fatalities , were undoubtedly caused by the use of defective or improperly assembled flame safety lamps . Had this same lack of understanding regarding the proper assembly of this safety device , and had the same indifference on the part of the user in keeping the lamps locked at all times and in proper condition , been permitted in a region where the coal dust was explosive , a terrible disaster would surely have resulted . In nearly every coal -mining country , including the United States , the Davy and Clanny type of lamp has been superseded , and rightly so , by some kind of bonneted lamp . Bonneted lamps , especially of the naphtha type , while much safer than the unbonneted , have more parts and need more care in assembling . For this reason the burden of responsibility for their being properly assembled rests with the lamp man ; therefore , it is extremely important that only competent , conscientious men be given this work .

Dec 1, 1921

By Rad B. Langston, Ted J. Williams, John A. Marjerison, Rimas T. Pakalnis, Tom M. Brady, Doug C. Bayer, Mark J. Bren

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By Robert A. Bruce

A motion transducer based on coherent mixing of laser light backscattered from rough surfaces is evaluated in terms of sensitivity, bandwidth and range. Tests made with a prototype composed of a 4-mw HeNe laser, a silicon avalanche photodiode, and a 15-cm aperture telescope demonstrate that remote measurements with reasonable bandwidth and accuracy are feasible at distances up to 100 meters.

Jan 1, 1977

Eliminate the need for roof bolter operators and their helpers to work under unsupported roof while setting or removing temporary supports before or during the roof bolting cycle-a task that annually accounts for approximately 20 percent of all roof fall fatalities. Approach The Bureau of Mines designed, built, and field tested an auto-mated temporary roof support (ATRS) that can be carried from place to place on the drill head of a single, fixed-head roof bolting machine (squirmer) used in low coal seams (less than 42 inches thick). How It Works The ATRS is designed for installation on any streamlined squirmer. It consists of a ten? foot-long, steel, wide-flange beam supported by two double-acting, telescoping hydraulic cylinders. A steel sleeve, mounted on the bottom center of the beam, is designed to fit over top of the

Jan 1, 1983

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977

By Jozef S. Stachulak

In This Chapter [Ore pass dust control Drill dust control Blasting dust control Conveyor belt dust control Transfer point and crusher dust control Roadheader dust control and How much ventilation air to use] This chapter discusses respirable dust control in underground hard-rock mines. These mines use a wide variety of extraction methods, but they have many common dust sources and dust control needs. Ore passes, drills, blasting, conveyor belts, transfer points, crushers, and load-haul-dump operations can be major sources of dust. Roadheaders, which are sometimes used in hard-rock mines, produce dust in large quantities. For the most part, dust in hard-rock mines is controlled with ventilation air, water sprays, and dust collectors. It is also important to prevent dust from getting into the air in the first place. Good dust control practices will reduce overall mine ventilation requirements. [Lack of maintenance is the main source of dust problems in hard-rock mines according to Rodgers [1974], who conducted a dust survey of hard-rock mines several decades ago. Rodgers found that spray systems had clogged sprays, dust enclosures had improperly fitted skirts, and ductwork was plugged and had leaks. Today’s mines have better maintenance programs (we think), but when dust levels are high, maintenance is still the first topic to address.] The Mining Association of Canada [MAC 1980] and Knight [1980] provide good general information about hard-rock dust control. For conveyor belt dust control, Goldbeck and Marti [1996] and Swinderman et al. [1997] are valuable sources of information.

Jan 6, 2003

Improve underground mine roof bolt support systems by alleviating problems associated with certain ground support systems currently being used. Approach Convert a passive resin-grouted roof bolt system into a uniform, tensionable roof bolting system. Background Resin-grouted roof bolts are one of the most common forms of ground support in U.S. underground coal mines. These support systems can be installed with a full-column of grout and be loaded with subsequent roof movements after installation. This is called a "passive" support system. An alternative to the passive support system is the mechanically-anchored, tensioned roof bolt system. This system is installed with resin grout. This system is designed to load or tension the support during installation by using a mechanical anchor, coupling, or threaded nut after the resin has properly cured. It is called an "active" support system and is used extensively for improved strata control in a laminated geologic deposition or in difficult ground conditions. To ensure that active bolts have been properly installed, the bolt loads must be checked by using a torque wrench or other suitable equipment. Unfortunately, this practice presents potential safety hazards and has limited accuracy. Laboratory and field experiments also reveal that the torque-to-tension ratio developed on active support systems can vary by 50% from bolt-to-bolt. Variations in bolt load installations can induce stress concentrations and lead to roof degradation or failure.

Jan 1, 1991

By W. P. Yant, R. R. Sayers

The rather sudden increase in the use of methanol as an antifreeze for automobile radiators has caused considerable comment , with some anxiety to persons interested in industrial and public health , regarding the possible health hazard in dispensing and using the product . In view of this , the chemical industry interested in the manufacture and marketing of methanol requested the Bureau of Mines to make an impartial and extensive investigation of the hazard involved . With the assistance of the industry this investigation is now in progress and will extend throughout the present winter . When these observations are finished a complete report will be made . At present , however , the acute interest in the problem and the many inquiries that have been received from manufacturers of methanol , garage owners , the automotive industry , public health officials , and private persons demands a brief statement relative to the reasons for the recent availability of methanol for antifreeze purposes , the plan of the bureau's investigation , and the trend of the results of the investigation obtained to date .

Dec 1, 1930

By Robert L. Lagace, Alfred G. Emslie

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

SMCRA contains five principal regulatory provisions that form the basis for its implementation: Performance Standards Performance standard safe intended to ensure that all surface mining is conducted in a way that protects the environment and the public and ensures that the mined land is restored to productive use following mining. Permits Before developing a surface or underground coal mine, an operator must have a permit issued under SMCRA. An application for a permit to conduct a surface coal mining operation is a detailed document that consists of text and numeric data describing the proposed mining and reclamation. Information must be furnished on pre-mining environmental conditions, existing land use, proposed mining and reclamation, how the performance standards will be met, and the post-mining land use. This provides the regulatory authority with the information necessary to determine that the operation can be conducted in accordance with the regulations. Performance Bonds Before a permit can be granted, an operator must post a performance bond sufficient to cover the cost of reclaiming the site in the event the operator fails to complete reclamation. The bond is not fully released until all performance standards have been met and reclamation of the site has been determined to be successful after five years in the East and Midwest, and after 10 years in the arid West. However, the bond can be partially released as various phases of reclamation are completed. Inspection and Enforcement If a violation of SMCRA or of a state surface mining and reclamation law is observed, an inspector issues a notice of violation to the operator. The violation must be corrected within a specific time, and the operator may also have to pay a fine based on the severity of the violation. If the violation is not corrected, acessation order is issued to immediately stop active coal mining, and the operator must pay a fine. If a violation is especially serious (for example, creates an Following reclamation, the land was immediately put back into agricultural production. Today, grain and corn crop yields have continually exceeded targets. 2 imminent danger to public health or safety or causes significant damage to land, air, or water resources) the inspector immediately issues a cessation order. An operator must correct all violations in order to obtain permits for new mines. Lands Unsuitable For Mining Congress recognized that certain coal deposits cannot be mined without permanent damage to unique cultural or natural resources. As a result, SMCRA protects these resources in two ways: It prohibits mining within the boundaries of national parks, forests, wildlife refuges, trails, wild and scenic rivers, wilderness and recreation areas; in areas which will adversely affect sites listed on the National Register of Historic Places; and within a restricted distance of occupied dwellings, public roads, buildings, parks, schools, churches, and cemeteries; and Provides a process that allows anyone whose interests may be adversely affected by proposed mining to petition to have specific lands designated unsuitable for mining.

Jan 1, 1992

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979