Search Documents

By R. M. Whyte

The complexities that exist in the nature of the basic feedstock to the metallurgical process call for a high degree of ingenuity from the extractive metallurgist in seeking the best possible treatment method for a particular ore. Drawing from personal experience the author presents four case studies that demonstrate the value of creative thinking in addressing the challenges typically encountered by the extraction metallurgist. It is concluded that creative expression most often occurs in response to a perceived strong need within an organization. By deliberately laying down meaningful challenges management can stimulate innovative thinking and achieve extraordinary results.

Jan 1, 2009

By V. Jovicic, J. Likar

The knowledge of the geological sequence and hydrological conditions in the area of portals was the basis for the design of the entry of the highway into tunnel Trojane. Mudstone, claystone and sandstone dominate the rock layering, which is tectonically reworked and contains structural anomalies. The complexity of the sequence makes it impossible to survey all the relevant features along the full 3km length of the tunnel. Sudden and frequent transitions between litological sequences impose potential instabilities and make the excavation of the tunnel particularly difficult. The initial survey established the zones of potential failures. These were monitored using topographic survey and inclinometers with an aim to make further geotechnical analyses more reliable and adjusted to the ground conditions. The analyses of the wall construction and the results of the monitoring showed that the design of the retaining wall was adequate. La connaissance de la séquence géologique et des conditions hydrologiques dans l'aire des portails a été la base pour la planification de l'entrée de l'autoroute dans le tunnel Trojane. Le schiste, l'argilite et le grès dominent la couche rocheuse qui est tectoniquement transformée et contient les anomalies structurales. A cause de la complexité de la séquence, il est impossible de revoir toutes les particularités le long des 3 kilomètres de la toute longueur du tunnel. Les transitions soudaines et fréquentes entre les séquences lithologiques imposent l'instabilité potentielle et font l'excavation du tunnel particulièrement difficile. La revue initiale a été établie sur les zones où il existe l'éboulement potential. Elles étaient contrôlées à l'aide de la revue topographique et de l'inclinomètre pour que les analyses géotechniques suivantes soient plus sûres et adaptées aux conditions du sol. Les analyses de la construction des murs et des résultats du contrôle ont montré que la planification du mur réteneur était correspondante. Der Autobahneingang in den Trojane Tunnel war projektiert auf Basis von der Kenntnis der geologischen und hydrogeologischen Bedingungen in dem Portalgebiet. Das Gebiet besteht aus dem Tonstein und dem Sandstein. Die Schichten sind tektonisch verformt und sind deswegen sehr heterogen. Die anfaenglichen Untersuchungen haben die Zonen von den potentiellen Bruechen definiert. Weitere geotechnische Analysen waren fitted an reale geologische Bedingungen durch das Monitoring der potentiellen Bruchzonen, welches aus den topographyschen Messungen und Inklinometerdaten entstand. Die Analyse des Wandbaues und die Resultate von dem Monitoring haben erwiesen, dass die Wandprojektierung entsprechend war.

Jan 1, 2003

By A. K. Singh, R. Singh, P. K. Mandal

On the basis of in situ study of pillar loading at different sites, an attempt is made in this paper to visualize the development of mining induced stress under varying geo-mining conditions. Field study demonstrated interesting interaction between size of pillar and nature of roof rock mass under the influence of increasing dimension of the excavation. Stiffness of pillars/overburden, extraction ratio and depth cover are observed to be the important parameters for the estimation of mining induced stress over the pillar. These parameters influence, both, the value of ultimate induced stress (vertical) and its range of influence ahead of the face line. Further, it is observed that the change in width/height (w/h) ratio of a pillar has got considerable influence over the nature of mining induced stress over it. Impact of highly dynamic nature of mining induced stress over the natural supports is observed to be the most serious factor for the safety of working under a hard and massive roof rock mass. On the basis of these observations, a conceptual model of interaction between the natural support and overlying strata is discussed in the paper. ZUSAMMENFASSUNG: Aufgrund ist in situ Studium von Säule Beladung an verschiedenen Stellen, ein Versuch in diesem Papier gemacht, die Entwicklung des Bergbaus vostellen sich, Spannung unter Änderung von Geo Bergbau von Bedingungen hat veranlaßt. Feld Studium hat interessante Wechselwirkung zwischen Größe von Säule und Natur von Dach Felsen Masse unter dem Einfluß von Vermehrung Dimension des excavation vorgeführt. Steifheit des Säulen Overburden, Herausziehung Verhältnisses und Tiefe sind beobachtet bedeckt, die wichtigen Parameter für die Schätzung des Bergbaus zu sein, Spannung über der Säule hat veranlaßt. Diese Parameter beeinflussen, beide, der Wert allerletzter veranlaßter Spannung (senkrecht) und sein Bereich des Einflusses voraus von der Gesicht Linie. Weiter ist, es beobachtet, daß die Änderung in Breite Höhe (W H) Verhältnis einer Säule beträchtlichen Einfluß über der Natur des Bergbaus erhalten hat, Spannung hat darüber veranlaßt. Schlag sehr dynamischer Natur des Bergbaus ist Spannung über den natürlichen Stützen beobachtet hat veranlaßt, der ernsteste Faktor für die Sicherheit des Arbeitens unter einer harten und massiven Dach Felsen Masse zu sein. Aufgrund dieser Beobachtungen, ein begriffliches Modell der Wechselwirkung zwischen der natürlichen Stütze und der überlagernde strata ist im Papier diskutiert. RESUME: En se basant sur dans l'étude de situ de chargement de pilier aux sites différents, une tentative est faite dans ce papier pour envisager le développement de creuse la tension persuadée sous varier de conditions de geo creuse. L'étude de champs a démontré l'interaction intéressante entre la taille de pilier et la nature de masse de rocher de toit sous l'influence d'augmenter de dimension de l'excavation. La raideur de piliers overburden, la proportion d'extraction et la couverture de profondeur est observée pour être les paramètres importants pour le jugement de creuse la tension persuadée par-dessus le pilier. Ces paramètres influencent, les deux, la valeur de tension persuadée ultime (vertical) et sa gamme d'influence en avant de la ligne de face. Plus, il est observé que le changement dans la largeur hauteur (le w h) la proportion d'un pilier a reçu l'influence considérable par-dessus la nature de creuse la tension persuadée par-dessus il. L'impact de nature extrêmement dynamique de creuse la tension persuadée par-dessus les soutiens naturels est observé pour être le facteur le plus sérieux pour la sûreté de fonctionnement sous une masse de rocher de toit dure et massive. En se basant sur ces observations, un modèle conceptuel d'interaction entre le soutien naturel et les couches recouvrant est discuté dans le papier.

Jan 1, 2003

By Li. S., C. Sili

Abstract. Study on nonlinear damage localization process of rocks under water chemical corrosion is a more interesting topic in rock mechanics research world widely. It is very important in estimating long term stability of rock engineering, design of nuclear waste repository and its performance estimation, geothermal and petroleum development. This paper reports that new development of study on the topic, including methodology, results of meso-mechanical test, real-time CT scan test and acoustic emission test, temporal fractal behaviors, neural dynamic modeling and chemical-induced damage law, etc. This paper also discusses the research directions of the topic in the near future. Zusammenfassung. Untersuchung zum durch die chemische Corrosion induzierten Schaedigungsprozess ist einer der Trends im Gebiet der Felsmechanik. Sie ist zugleich ein sehr wichtiges Forschungsprojekt u.a. fuer geotechnische Langzeitstabilitaetsanalyse, Langzeitsicherheit eines Endlagers, Erdwaerme- und Erdoelfoerderung. Dieser Aufsatz stellt die neusten Entwicklungen in den folgenden Teilgebieten zusammen: Untersuchungsmethoden, Laborversuchsergebnisse der Mikromechanik, der Computer-Tomographie und der akustischen Emission, zeitabhaengige Fraktaleigenschaften, Modelle fuer die Nervendynamik sowie Modelle fuer chemie-induzierte Schaedigungen. Zum Schluss werden kuenftige Forschungsschwerpunkte bzw. –richtungen diskutiert. Résumé L’étude du processus de la localisation de l’endommagement du à l’érosion chimique est un thème d’actualité pour la mécanique des roches. Elle est également un sujet de recherche d’importance dans l’évaluation de la stabilité à long terme des ouvrages rocheux, l’analyse du system de stockage des déchets nucléaires et l’évaluation de son comportement, l’exploitation de l’énergie thermique et pétrolifère, etc. Cet article présente le développement actuel dans ce domaine, incluant la méthodologie d’étude sur le processus de la localisation de l’endommagement dû à l’érosion chimique, l’analyse des essais mécaniques avec l’observation microscopique, du balayage en temps réel (CT), et de l’émission acoustique. On aborde ainsi modèle des caractéristiques fractural du temps, le modèle de la mécanique dynamique neural, ainsi que la loi de comportement d’endommagement dû à l’effet chimique. Enfin, les perspectives relatives à ces études sont présentées et discutées.

Jan 1, 2003

By Simon Mundike, Muwindwa Lipalile

A scraper based block cave method has been successfully applied to extract the Lower Ore Body at Nchanga since the 1950?s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas; the 2420 8E 1C trial drift was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre reinforced shotcrete was extended to other drifts. This paper describes the application of fibre reinforced shotcrete at Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

By Willem Le Roux

The common law requires an employer to take reasonable steps for the safety of employees. In general, the duty of care means that the employer, acting personally or through its employees or agents, must take reasonable care for the safety of its employees (Van Deventer v Workmen?s Compensation Commissioner; 1962 (4) SA 28 T; Oosthuizen v Homegas (Pty) Ltd 1992 (3) SA 463 T).The duty of care includes the provision of safe premises, safe machinery and tools and a safe system of work. The obligation is not an absolute one, but is restricted by the concept of reasonableness. The common law duty may, in certain cases, include the assessment of hazards and risks. 2 International law Great emphasis has been placed in the Western world on the prevention of occupational diseases and injuries. Detailed statutes and regulations govern specific industries in many countries. See, e.g. the Control of Substances Hazardous to Health Regulations of the United Kingdom and various regulations applicable to the use of asbestos and lead, fire protection, mines and quarries, petroleum, etc. Risk management is an important part of managing health and safety. In the United Kingdom, the Management of Health and Safety at Work Regulations, 1999, require every employer to make a ?suitable and sufficient assessment of the risks to health and safety of his employees to which they are exposed whilst they are at work?. The particularity of the assessment is determined by the risk in question.

Jan 1, 2011

By Patrick J. Foster

This paper summarises a behavioural safety project undertaken in seven quarries in the UK in order to investigate its applicability as a means of raising the standards of health and safety in the UK quarrying industry. A behavioural safety methodology was developed and trialled at two quarry sites in the UK. During the study the number of unsafe acts and minor accidents had decreased and at one of the quarries there was a 95% reduction in the number of working days lost. It was then introduced at a further five sites of varying sizes and within this focused specifically on lone workers as well as behaviours that affected quality and environmental issues. Positive improvements were noted in most of these operations. The project also looked at the effectiveness of health and safety performance indicators. Here, the common lead and trailing indicators for both safety and health that are commonly used by industry were identified. In consultation with the UK quarrying industry these were then used to identify specific performance measurement criteria that can be used by the quarrying sector to measure performance. Following on from this a quarry specific health and safety management system specification was developed for large and small quarries.

Jan 1, 2008

By G. Wu, S. Liu

In view of the singleness of traditional methods about international petroleum (Brant) price forecast, ten main factors that affect international petroleum price are fully analysed. Based on time series method and multivariate linear regression method, the simulation model with the theory and idea of system simulation is firstly established. And this forecasting system realizes visual operation under the environment of MATLAB/SIMULINK. So this article tries a new way for further exploring petroleum price’s running law and guiding its forecasting practice. Keywords: Petroleum price forecast, system simulation, residual error, physical flows information flows

Jan 1, 2003

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By J. -H. Wu, S. Nishiyama, Y. Ohnishi

The behaviors and stress distributions of the inclined jointed rock masses with different dip angles obtained from DDA are compared to the results of laboratory tests. By calculating the block stress distributions, it is confirmed that DDA can reproduce the arching around the trap door when lowering the trap door. The shapes of arching change with the angles of inclined layers. In addition, the earth pressures acting on the trap door shows non-symmetrical distributions when the layers are not horizontal. The stress concentration occurs in one side of the rock masses close to the trap door. Furthermore, the surface settlements are also related to the inclined angle, and the loosening zone in rock masses can be different from Terzghi’s theory [1]. Since, simulations have good agreements with the laboratory test , it demonstrates the applicability of DDA to explain the mechanical behaviors of tunnel, such as arching phenomenon, non-symmetrical earth pressure distributions acting on the trap door, and the surface settlement profile in the jointed rock masses. Dans cet article est décrite l’étude numérique du perçage d’un tunnel dans un massif de couches rocheuses jointes inclinées. La simulation à l’aide de l’Analyse de Déformation Discontinue (DDA), en faisant varier l’angle d’inclinaison des couches de roche, nous apporte des résultats en termes de distributions de contraintes et de comportement des couches, résultats qui sont ensuite comparés avec des résultats de tests en laboratoire. Les résultats confirment le fait que la DDA est capable de reproduire le phénomène d’arcage autour de la trappe lorsque la trappe s’abaisse. Les formes d’arcage varient selon l’angle d’inclinaison des couches de roche. Par ailleurs, lorsque les couches ne sont pas horizontales, la distribution de pression agissant sur la trappe est assymmétrique. La concentration de contraintes se produit du coté proche de la trappe. De plus, les tassements de surface dépendent eux aussi de l’angle d’inclinaison. En conséquence, les résultats de simulation sont en accord avec les tests en laboratoire, ce qui prouve que la DDA permet d’expliquer des comportements mécaniques du tunnel tels que l’arcage, les distributions assymmétiques de pression du sol sur la trappe, ainsi que le profil du tassement de surface dans la masse de roches jointes. Dieser Beitrag beschreibt eine numerische Studie über Tunnel im geklüftetem Fels. Das Verhalten und die Druckverteilungen in den unterschiedlich geneigten und geklüfteten Felsenmassen wird mit Hilfe des Discontinuous Deformation Analysis Programms (DDA) simuliert, und mit Laborversuchen verglichen. Die Resultate bestätigen, dass DDA der Gewölbewirkung im „Trapdoor“ Experiment gut reproduzieren kann. Die Form des Gewölbes, ändert sich mit unterschiedlichen Neigungswinkeln der Schichten. Bei geneigten Schichten entstehen unsymmetrische Druckverteilungen. Auch die Oberflächenabsenkung ist von dem Neigungswinkel abhängig. Die gute Übereinstimmung der Simulationen mit den Laborversuchen zeigt, dass die DDA-Methode gut geeignet ist, um das mechanische Verhalten von Tunneln, wie z.B. den Effekt der Gewölbewirkung, die unsymmetrischen Druckverteilungen bei geneigten Schichten, oder die Oberflächenabsenkung in geklüfteten Felsenmassen, zu erklären.

Jan 1, 2003

Dr R. E. Robinson, Pr. Eng., obtained a B.sc. (Chem. Eng.) cum laude from the University of the Witwatersrand in 1950 and a Ph.D. (Eng.) from the same University in 1953, where he was awarded the Haikes Memorial Medal for Industrial Chemistry. Professor G. G. Garrett was appointed Professor of Physical and :Fabrication Metallurgy in the Department of Metallurgy at the University of the Witwatersrand in June 1980, and in January 1984 he became Head of the Department. Mr P. A. van Wielligh, Pr. Eng., climbed the mining ladder in the hard way, starting as a Mine Surveyor in 1936 and working his way up as Chief Surveyor, Underground Manager, Mine Manager, and Consulting Engineer, to Executive Director, including the intermediate steps. Mr H. E. James, Pr. Eng., is a graduate in Chemical Engineering from the University of the Witwatersrand. Both his B.sc. degree (1961) and his M.sc. degree (1964) were obtained on bursaries, the former from Gold Fields of South Africa and the latter from the Atomic Energy Board. Mr G. Pienaar, Pr. Eng., obtained a B.Eng. (Met) in 1967 and an M.Eng. in 1973, both from the University of Pretoria. Dr A. K. Haines, Pr. Eng., obtained all his degrees from the University of Natal, finishing with a. Ph.D. in 1971. Mr B. C. Alberts, Pr. Eng., obtained his academic training at the University of Pretoria, where he was awarded B.sc. degrees in both agricultural engineering (1963) and mining engineering (1965). Mr H. C. van Zyl, Pr. Eng., holds B.sc. degrees in mining engineering (1968) and civil engineering (1972), both from the University of Pretoria.

Jan 1, 1984

By M. Tangstad, H. Brun, P. Calvert, A. G. Lindseth

In 1999, Eramet bought the ferromanganese plants in Porsgrunn and Sauda (Norway) and Marietta (USA). With an ownership in the Comilog mine, the plants will operate with a high amount of Comilog ore. The properties of Comilog ore are reviewed and compared to a number of industrial operations. Important ore properties are chemical and mineralogical analyses, CO reactivity and mechanical strength. The advantage of Comilog ore is its contribution to lower energy and coke consumption. However, special precautions must be taken regarding the amount of fines and water introduced in the furnace, as Comilog ore is more porous compared to other Mn ores.

Jan 1, 2004

By J. F. Shao, G. Duveau, W. Z. Chen, O. Ozanam

In this paper, we present a sensitivity study for the numerical modelling of hydromechanical coupling around a shaft in partially saturated claystone. Two representative constitutive models have been used: an elastoplastic damage model (IDEPLML) and an elastic perfect plastic model based on the Hoek and Brown failure criterion (H&B). A series of comparative studies have been performed with respect to main parameters involved in coupling process (mechanical, hydraulic and hydric properties). The emphasis is put on the evaluation of induced plastic, damaged and failed zone due to excavation and drying process. Dans ce papier, nous présentons une étude numérique paramétrique du comportement hydromécanique couplé d’une argilite partiellement saturé, lors du creusement et de la maintenance d’un puit L’étude paramétrique porte à la fois sur le type de modèle et sur les principaux paramètres (mécaniques hydrauliques et hydriques) intervenant dans le couplage. L’accent est principalement porté sur l’évaluation des zones plastifiées autour de l’ouvrage lors de la désaturation. In unserem Beitrag geht es um eine digitale parametrische Untersuchung über das hydromechanische Verhalten eines teilweise durchtränkten Tons beim Abteufen und dem Betrieb von Schächten. Die parametrische Analyse konzentriert sich auf den Modelltypus und auf die wesentlichen bei der Verbindung wirksamen Parameter, d.h. die mechanischen, hydraulischen und hydrologischen. Der Schwerpunkt liegt auf der Bewährung der plastifizierten Bereiche des Bauwerkes während der Austrocknung.

Jan 1, 2003

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By M. Yavuz

Two different methods of fuzzy multiple criteria decision making have been proposed to solve the problem of mining method selection in the paper titled ?Mining method selection by multiple criteria decision making tool, by Bitarafan and Ataei. This problem is really important and also difficult to solve because of the need of handling many criteria simultaneously in the process of decision making. Bitarafan and Ataei have selected 15 criteria for the case study in their paper and those criteria have not been clustered/grouped yet. The number of selected criteria is only 15, although there are more criteria that should be handled in a real case, because they have used Saaty?s method in the section ?Fuzzy multiple attribute decision making? in their paper. Saaty?s method considers the pair wise comparison of criteria and uses random indexed which have already been derived and published. Available random indexes, however, have been derived for maximum 15 criteria so far.

Jan 1, 2007

This publication is provided on an "as is" basis without warranties of any kind, either expressed or implied including, but not limited to warranties of title or implied warranties of merchantability of fitness for a particular purpose. The information contained in this publication is for general information purposes only. It does not constitute professional, technical, financial or other advice to the user of this publication and must not be relied upon as such by any person whatsoever. The use of this publication is at the users own risk. The authors/creators of the information contained in this publication have tried to ensure that the information contained herein is correct, but errors or inaccuracies may exist or the information may be incomplete, unreliable or no longer up to date. Therefore, no warranties of any nature whatsoever are given and any liability to any person in respect of anything and in respect of the consequences of anything done or omitted to be done, wholly or partly in reliance upon the whole or any part hereof, are disclaimed, including and without limitation any contractual, dialectal, direct, consequential or financial damages or losses. On no account will Organisers and/or any of the contributors or any person or entity involved in creating, producing or distributing the information and or software available in this publication be liable for any such damages arising out of the use of or inability to use this publication. Copyright Reserved The South African Institute of Mining and Metallurgy P O Box 61127, Marshalltown 2107, South Africa www.saimm.co.za All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without the written permission of the copyright owner. Although the greatest care has been taken in the compilation of the entire contents, the editors and publishers do not accept responsibility for errors or omissions. First Edition Copyright February 2004 Proceedings ISBN: 0-9584663-5-1 (1 volume and CD-ROM)

Jan 1, 2004

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

By A. C. Moorgas, J. Divall

This study investigates the feasibility of using waste iron slag, the by-product from a mineral sands processing works, in road construction. The study includes the different options investigated for the treatment of a leachate that is produced during the cooling of the iron slag, prior to processing. It also reviews the reasons for choosing the current treatment option that is being trialed. Cooling the iron slag with water results in the formation of a leachate with a high pH and high sulphide concentration. This leachate can seep into the ground and, over time, it will contaminate the ground water. A system was designed to collect and treat the leachate to prevent contamination of surrounding natural water sources. Numerous leachate treatment options were investigated to find cost effective method of treatment After cooling, the iron slag is passed through an iron recovery plant and the unsaleable product is placed on a dumpsite. Rain percolates through the dumpsite, which can result in the formation of a leachate that can contribute to a contaminated plume. After extensive testwork, it was found that the dumpsite, which was leached of contaminants, could be screened and used as a G5material (specifications in Table II) in road construction. The initial challenge was to establish that this material was environmentally safe for use in this particular application. Approval from the Department of Water Affairs (DWAF) was required for the testwork and then for the long-term use of this material in the construction industry. The following challenge involved establishing a market for the material. Construction companies in the area were reluctant to change to a new product that was not naturally occurring. The economics of this project are extremely sensitive to transport costs and hence only projects within a specified radius can be supplied with the Black Top Gravel (BTG). This project is not are venue generator, but it does save the money that would be required to manage the dump, and it reduces the closure costs.

Jan 1, 2003

By D. G. Hulbert, D. J. Oosthuizen, D. de V. van der Spuy

Expert Online, as a software system, is aimed at providing plant operators in the minerals industry with effective training and on-the-job assistance. It incorporates a number of features to achieve this goal, of which the most important is its ability to explain the dynamics of the plant and control system in simple language, mimicking an informed plant expert who has online access to the inner workings of the plant and control system. This is made possible by a novel form of Artificial Intelligence, called the Interpreting Expert System. Previous implementations of the IES were only capable of explaining controller actions. Expert Online will extend this capability to also perform the more difficult task of explaining process behaviour. Expert Online will implement three main processes, namely the accumulation of data from the controllers and plant models, the interpretation, processing and filtering of that data and lastly communicating the relevant information to the user, both as written messages and in other audio-visual forms. Although Expert Online is aimed at the operator, other plant personnel, like supervisors and plant managers, will also benefit from it. This paper focuses on the structural and functional design of Expert Online for implementation on the latest version of Mintek’s open control platform, PlantStar, highlighting advances and additions since the previous implementations of the Interpreting Expert System and concluding with an example illustrating some of the principles.

Jan 1, 2003

By B. K. Loveday

The South African Institute of Mining and Metallurgy hosted a School on 'The Practical Design of Comminution Processes' at Megawatt Park (near Johannesburg) on 14th to 16th May, 1991 Derek Barratt, a Senior Consultant of Wright Engineers, Canada, and the main speaker, provided a good insight into how Wright Engineers design milling circuits, particularly large semi-autogenous mills. He was ably assisted by Jens Lichterof Allis Mineral Systems, who described some interesting examples of pilot-plant testwork and summarized South African milling practice. Mike Moys of the Witwatersrand University spoke on the influence of pulp viscosity on mill performance, and Johan Engelbrecht and Jeremy Bosman of Multotech

Jan 1, 1991