Search Documents

By C. Steyn, J. D. le Roux

A dynamic model is used to represent the single-stage closed grinding mill circuit at Mogalakwena North Concentrator. The circuit consists of a ball mill closed by a hydrocyclone. The circuit is modelled according to a semi-mechanistic non-linear dynamic model available in literature. An algebraic routine is used to fit model parameters to steady-state process data. Preliminary validation results against dynamic data indicate that the model is capable of capturing the main dynamic trends of the plant. Since classical system identification techniques proved insufficient to produce accurate models; the non-linear model can be used as a reliable source for model-predictive controller design. Keywords: Grinding, modelling, process control, parameter estimation

Jan 1, 2020

By C. A. Young, J. L. Bowden

"Cyclic voltammetry experiments were conducted on copper and chalcopyrite (CuFeS2) in the absence and presence of ethyl xanthate, and compared to mass-balanced EH–pH diagrams. The results for copper duplicate those found in the literature and confirm xanthate chemisorption. However, the, results indicate that chalcopyrite oxidizes to chalcocite (Cu2S) and only afterwards is chemisorption observed due to small currents appearing with xanthate. This phenomenon suggests that the mineral's hydrophobicity is induced by more than dixanthogen and copper xanthate. Hydrophobicity was found to be pH-dependent over a range of alkaline conditions (pH 7–11) at narrow potentials (0 to –200 mV). An EH–pH diagram for chalcopyrite with xanthate is presented to illustrate the conditions under which chalcopyrite would be hydrophobic and thereby more thoroughly explain the results in the literature. IntroductionSulphide minerals are generally concentrated from ores by froth flotation, a physiochemical process that induces separation based on differences in hydrophobicity. In this process, a gas is bubbled into a slurry and the minerals that are hydrophobic (water-repelling) adhere to the bubbles and float to the surface while the hydrophilic (water-loving) minerals remain in the slurry. With sulphide minerals, the hydrophobicity is generally established in two ways. The first is by the addition of a collector, which is a heteropolar molecule with a reactive inorganic head group and an inert organic tail. Typically, the head group bonds with the sulphide mineral surface by adsorbtion either chemically (chemisorption) or physically (physisorption) or by complexing with atoms that solubilize somewhat at the surface (surface precipitation). These interactions leave the organic tail protruding from the mineral surface, thereby inducing hydrophobicity. The second method is by oxidation of the mineral surface to form a layer that is metal-deficient/sulphide-rich or comprised of elemental sulphur. Because the layer mimics naturally hydrophobic sulphur, this enables ‘collectorless’ flotation. Furthermore, this oxidation phenomenon adds an electrochemical dimension to the understanding of sulphide mineral flotation."

Jan 1, 2016

By K. Wu, L. Li, D. W. Zhou, J. W. Yu

The presence of a fractured water-conducting zone (FWCZ) is of significant importance for the safety of underground mining under water bodies. When a coal mining area is covered with a thick layer of alluvial soil, the height, width, and distribution pattern of the FWCZ in the area shows unique features. The internal mechanism by which thick alluvial soil affects the FWCZ is still unknown. Using the Huainan coal mining area (HCMA) in China as a case study, we investigated the impact of thick alluvial soil on the height, width, and distribution pattern of the FWCZ through numerical simulation using the distinct element method, theoretical derivation, and data validation. The results indicate that a thick layer of alluvial soil inhibits the FWCZ height and increases the FWCZ lateral width. When the soil-to-rock ratio is greater than a certain value (the numerical result in this study is 15:18), the FWCZ height and width are affected by the thick alluvium significantly, and the thick alluvial soil alters the shape of the FWCZ from tall and thin to short and wide. The load exerted by the alluvial soil transfers downward to influence the FWCZ; however, this process is obstructed by the hard strata in the bedrock. Therefore, the vertical and lateral change trends show a similar step pattern. Our results can provide a basis for accurate calculation of the FWCZ height in mining areas with thick alluvial soil, to mitigate mine water hazards and increase the safety of underground mining in coal mines covered with a thick alluvium layer. Moreover, reducing the FWCZ height can help extend the upper extraction limit in coal mines covered with a thick alluvium layer, which reduces the thickness of the impermeable coal pillar and increases coal production.

Jan 1, 2016

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"Currently, the matted-based collection process is most widely used for platinum group metal (PGM) recovery. However, because PGM-containing concentrates are becoming more enriched with UG2 (Upper Group 2) low-grade concentrates, this is expected to be integrated or replaced with an alloy collection process.The reduction LG (low-grade) concentrates with silicon carbide (SiC) was investigated. The purpose of the study was to ascertain the feasibility of using SiC as reductant with regard to metal fall, PGM grade in the alloy, slag composition, and overall PGM recovery, and if possible, the integration of such a process in the current matte-based collection process. Rowland and Easterns LG concentrate samples from Lonmin were analysed by Xray diffraction (XRD), X-ray fluorescence (XRF), and inductively coupled plasma mass spectrometry (ICP-MS). It was found that SiO2 and MgO are the most abundant oxides and Pd is the most abundant of the PGMs. Sulphide-bearing minerals such as chalcopyrite were detected in low concentrations (below 1%), and Cr2O3 concentrations are between 2-4%. SiC reduction of Rowland and Easterns concentrate were conducted at 1600°C with reductant to concentrate ratios ranging from 2.5 to 3.5 kg SiC per 100 kg concentrate.The reduction experiments revealed that PGM recoveries from Rowland concentrate were poor. SEM images showed entrained metal prills in the slag phase. The slag viscosity at the end of the melt was calculated by using FactSage, and the results indicated that the viscosity was higher than 4 poise, which is above that of Easterns slag. PGM recoveries for Easterns concentrate were significantly better. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered in a test with a reductant to concentrate ratio of 3.5 kg SiC per 100 kg Easterns concentrate. At this reductant to concentrate ratio, Fe recovery was also the highest, at 66%. SEM imaging of a slag sample revealed few or no metal prills entrained. The FeO content in the initial concentrate charge was then increased by adding Peirce-Smith converter slag in order to decrease the slag viscosity and further increase PGM recovery. A test was conducted with the addition of 10 kg converter slag per 100 kg Easterns concentrate. The reductant to concentrate ratio was kept at 3.5 kg SiC per 100 kg Easterns concentrate. The Ir and Pd recoveries were more than 95%, while Pt recovery was almost 70%. Fe recovery increased to 76%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and Peirce-Smith converter slag were calculated. FactSage predicted that the concentrate charge should consist of 70-80% Easterns concentrate with 20-30 kg converter slag per 100 kg LG concentrate. SiC reduction of this optimum LG concentrate charge is expected to recover more than 90% of all PGMs. Cr and Si concentrations in the alloy will be below 1% in total.The effectiveness of SiC as reductant was also compared to carbon reduction. Carbon reduction of an optimum concentrate charge at the same reductant to concentrate ratio resulted in a marginally higher metal fall than SiC reduction. However, gas emissions and energy requirements are higher for carbon reduction.The study has shown that base metals and PGMs can be recovered in an iron alloy by SiC reduction of LG concentrate with converter slag additions. Integration of such a process into the matte-based collection process could be considered as a future alternative for smelting UG2 LG concentrates."

Jan 1, 2014

By and M. V Roper, H. N. Engelbrecht

Quality control interventions emanate from process upsets and trends that move product quality beyond the natural variation expected in a stable process. The ability to detect upset conditions and react in an effective manner protects both resource utilisation and compliance to specifications. Product quality control on coal processing plants traditionally relies on the reference (combined sampler and laboratory) system to measure product qualities. The introduction of online analyser (OA) technology, applied in different configurations, creates a second source of measurement information for control decision making. The case study was done on the primary sample stream of the final product stream at Exxaro’s GG7 and 8 plants, part of the Grootegeluk complex. It explores the OLA system’s ability to meet the OEM performance guarantee, perform equally to the reference system without analytical delay time, and assesses the effort to achieve this performance in a by-line analyser (BLA) configuration. In the paper, a conceptual comparison of the two measurement systems is done and the theoretical and practical comparison of measurement performance is discussed. Results demonstrate that the OA outperformed the OEM’s performance guarantee and achieved similar levels of performance to the reference system without the response delay. Keywords: Online analyser (OLA), by-line analyser (BLA), coal quality measurement, measurement performance

Jan 1, 2020

By D. K. Chibwe, P. Taskinen

"Typical operation of industrial Peirce-Smith converters (PSCs) used in copper smelting results in several common phenomena such as excessive splashing, slopping, tuyere blockage, and low converter campaign life due to high tuyere line refractory erosion. These phenomena give rise to an inefficient operation from both a process and an energy perspective.This investigation presents numerical and physical models of flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a slice model of an industrial PSC. For physical simulations, a 0.2-scale cold model was developed. Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The two- and three-dimensional numerical simulations of the three-phase system were carried out using volume of fluid (VOF) and realizable k- e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Both numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions employed in the investigation. Measurement of mass transfer characteristics conclusively indicated that fluid flow in the PSC is stratified. Both blowing configuration and volume of slag in the converters were found to have significant effects on mixing propagation, wave formation, and splashing.The splashing and wave motion in these converters are known to cause losses of metal/matte and potential production time due to the requirement for intermittent cleaning of the converter mouth, resulting in reduced process throughput. To prevent these losses and hence to increase process efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined, as well as lateral, blowing conditions. In comparison, the recent results of the combined blowing concept were found to be encouraging."

Jan 1, 2014

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec's first diamond mine by 2013.

Jan 1, 2010

By J. Arzuúa, U. Castro-Filgueira, L. R. Alejano, F. Malan

"Pillar design for underground mining is typically done using empirical formulae or numerical modelling. Practical experience and recent literature, nevertheless, illustrate the shortcomings of these design approaches. Ongoing monitoring of pillars is therefore recommended to minimize the risk associated with these designs.In a mine where a large number of pillars are cut, different pillar strengths can be expected owing to variations in rock mass strength from area to area. This problem is compounded by the fact that in mining environments the pillars are not always cut according to the prescribed dimensions. Although the original design using either empirical methods or modelling may predict stable pillars, unstable pillars will be encountered in reality. Very conservative designs with large factors of safety may circumvent this problem, but this approach is uneconomical.A possible solution to localized stability problems may be to enhance the strength of a few unstable pillars. It may even be hypothesized that reinforcing a few critical pillars may prevent ‘pillar runs’ on a much larger scale. Rockbolting, strapping of pillars, and pillar shotcreting have occasionally been used in the past as possible solutions. It appears that these have not been successful in all cases and large collapses have occurred in spite of the pillar remedial work.The authors investigated the strapping of pillars by conducting laboratory tests on cabled rock specimens. The results were qualitatively compared to actual attempts of pillar reinforcement available in the literature, as well as additional observations in an old haematite roomand- pillar mine in Spain. Based on these results, the value of steel cabling and mesh wrapped around pillars to improve stability is demonstrated. Some cases where this approach will not be successful are also discussed."

Jan 1, 2017

By S. Kauchali

"Underground coal gasification (UCG) is recognized as an efficient mining technique capable of chemically converting the coal from deep coal seams into synthesis gas. Depending on the main constituents of the synthesis gas, chemicals, electricity, or heat can be produced at the surface. This paper provides a high-level graphical method to assist practitioners in developing preliminary gasification processes and experimental programmes prior to detailed designs or field trials. The graphical method identifies theoretical limits of operation for sensible gasification within a thermally balanced region, based primarily on the basic coal chemistry. The analyses of the theoretical outputs are compared to actual field trials from sites in the USA and Australia, with very favourable results. A South African coal is studied to determine the possible synthesis gas outputs achievable using various UCG techniques: controlled retractable injection point (CRIP) and linked vertical wells (LVW). For CRIP techniques, an important result suggests that pyrolysis, and subsequent char production, are important intermediate phenomena allowing for increased thermal efficiencies of UCG. The conclusion is that South African coals need to be studied for pyrolysis-char behaviour as part of any future UCG programme. The results also suggest that UCG with CRIP would be a preferred technology choice for Bosjesspruit coal where pyrolysis dynamics are important. Lastly, the use of CO2 as oxidant in the gasification process is shown to produce syngas with significant higher heating value. Introduction and literature surveyCoal is a commonly utilized fossil fuel, providing over 40% of global electricity demand and about 90% of South Africa’s primary energy needs. However, less than 20% of the known world resources are suitable for possible extraction using conventional surface and underground mining techniques (Andrianopolous,, Korre, and Durucan, 2015). Underground coal gasification (UCG) has the potential to recover the energy stored in coal in an environmentally responsible manner by exploiting seams that are deemed unmineable by traditional methods. The UCG process, if successfully developed, can increase coal reserves substantially. For example, in the Limpopo region of South Africa alone, the estimated potential for UCG gas, based on existing geological records, is over 400 trillion cubic feet (TCF) natural gas equivalent – this is about a hundred times more gas than the existing 4-TCF Pande-Temane natural gas field reserve in Mozambique (de Pontes, Mocumbi, and Sangweni, 2014)."

Oct 1, 2018

By H. Jiang, W. Wang, Y. Zhao, J. Qiao, C. Duan

DEM simulations were used in this research to study the screening process of a novel variable amplitude equal thickness vibration screen (VAETVS). The response regularity of mass distribution and granular moving velocity at the different screen panels to feed rate was investigated and the predictive model for the unit area processing load was proposed. The influence of aperture size, the size variance, and the opening ratio on the mass passing-distribution and overall screening performance, respectively, were revealed. The results showed that the response model of the unit area load Ф to the feed rate Q can be concluded as Ф∝0.324×Q. The moving velocity of particles also showed a positive relevance to the feed rate, besides which the passing rate of fine-grained material at the feed end was negatively related to the aperture size, while the case was reversed in the feed end. The increase of aperture variance AV enhanced the passing ability of small particles at the feed end,and reduced the misplaced ratio of the large particles at the discharge end. A better screening efficiency can be obtained when the average aperture size of the entire sieve is 7.5 mm, with the aperture variance of 1 mm between the adjacent panels. When the combination of the opening ratio is 35-35-40, a better screening effect can be achieved. Keywords: Equal thickness screening, DEM, particulate velocity, mass distribution regulation

Jan 1, 2020

By K. Thambi

"A recent amendment to Section 36(11)(e) of the Income Tax Act, 53 of 1968 (Tax Act) now extends the allowable deduction of ‘capital expenditure’ incurred by mining companies pursuant to the Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA). In terms of the Taxation Laws Amendment Bill 2016 (TLAB 2016), the allowable deduction has been extended to include expenditure incurred on infrastructure in terms of Social and Labour Plan (SLP) requirements as per the MPRDA. Interestingly, what necessitated the amendment was the need to recognize SLP requirements and to circumvent administrative difficulties for mining companies and the South African Revenue Services (SARS) in differentiating the use of developmental infrastructure by employees or the community. The successful implementation of such a deduction hinges on a sound SLP system. However, given the challenges within the current SLP system, this amendment could be considered somewhat premature. IntroductionSection 36(11) of the Income Tax Act 58 of 1962 (Tax Act) enabled mining companies to deduct certain capital expenditure in lieu of its other sections. In particular, it made provision for mining companies to deduct capital expenditure incurred pursuant to the Mineral and Petroleum Resources Development Act 28 of 2002 (MPRDA), but excluding capital expenditure incurred in respect of infrastructure or environmental rehabilitation. As such, mining companies could only deduct such capital expenditure that related directly to their employees and not to the wider community (Clegg, 2018).In terms of the Taxation Laws Amendment Bill 2016 (TLAB, 2016) (South Africa, 2016a), the recent amendment to Section 36 extends the relief provided under section 36(11)(e) to include capital expenditure incurred on infrastructure in terms of the Social and Labour Plan (SLP) requirements of the MPRDA. In other words, the capital expenditure incurred by the mining company for the benefit of the people living in mining communities. To qualify for such a deduction, the infrastructure erected or developed by the mining company should reflect what was agreed between the mining company and the Department of Mineral Resources (DMR) as per the SLP requirements of the MPRDA (TLAB 2016)."

May 1, 2019

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

For gold plants in Russia, it is very complicated and costly to use cyanide leaching for efficient processing of gold refractory ores, where gold is closely associated with sulphide minerals and the significant amount of natural carbonaceous matter present. Oxidative roasting of gold refractory concentrates is a well-known method, making it possible to obtain a high recovery rate of precious metals to a target product. The use of oxidative roasting is limited in general by the expense of capturing and neutralising the harmful components of roasted gas, mainly sulphur (SO2, SO3) and arsenic (As2O3) oxides. This paper addresses testing and development of an optimised technology to process gold refractory gravity and flotation concentrates by means of oxidative roasting which stabilises arsenic as calcium arsenate. The process involves roasting of a gravity or flotation refractory ore concentrate in a mixture with lime and calcium chloride, with a supply of oxygen, and at 600-700°С. During the roasting a carbonaceous matter of the concentrate burns out and sulphide components transform into harmless calcium sulphate (CaSO4) and calcium arsenate (Ca3(AsO4)2), and iron passes into the form of hematite (Fe2O3). After disintegration, the roasting cinder is concentrated on a table to obtain a high-grade gravity concentrate and gravity tailings. The high-grade gravity concentrate is subject to smelting in a mixture with fluxing agents, which results in alloyed gold and slag. The gravity tailings are ground and reported to cyanide leaching. In the case of a flotation concentrate, the roast cinder is ground to minus 30 μm and subject to sorption cyanide leaching. High gold recovery (90-95%) of the target product and environmental safety are typical of the improved technology under consideration. Two national patents were granted for the methods developed to treat refractory concentrates bearing precious metals. Keywords: Gold concentrates, oxidative roasting, cinder, cyanide leaching, smelting, alloyed gold

Jan 1, 2020

By G. S. Hansford, J. W. de Kock, C. D. Levy

Rheological measurements on pulps from South African gold mines by G. s. HANSFORD, Ph.D. (Pennsylvania), M.Sc. (Cape Town), C. D. LEVY, B.Sc. (Eng.), and J. W. DE KOCK, Ph.D. (Cantab.), B.Sc. (A.I.C.) (Visitors) A method is described for the determination of the rheological parameters of a fast-settling slurry with conventional viscometric measuring equipment. The effect of concentration, temperature, and pH on these parameters is investigated. The results agree with those obtained by previous workers using different viscometers, but this method allows a more detailed characterization of all the properties. From a literature survey, two semi-empirical equations were found that allow the effect of concentration, temperature, or pH on the rheological parameters to be correlated.

Jan 3, 1976

Prof C T O'Connor holds the degrees of BSc, BSc Hons, University of Cape Town (UCT), where he started his academic Lecturer in the Department of Physical Chemistry in 1976. Mr P Smith, educated in England and the former Southern Rhodesia, joined Gold Fields of South Africa in 1966 as a Metallurgical Learner Official. After obtaining a BSc Eng at the University of the Witwatersrand in 1972, he returned to Gold Fields. Mr P D K Robinson was born in Zimbabwe, and was educated at Dale College in Kingwilliamstown, matriculating in 1952. He holds a Mine Surveyor's Certificate obtained in 1961) and a Mine Manager's Certificate (obtained in 1966), as well as an EDP from the University of the Witwatersrand.

Jan 1, 1991

The 96th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 11th August, 1993. OBITUARIES The President announced the deaths of the following members of the Institute during the past year. Life Fellow E.F. Laschinger. Other Members R.K. Boright, J.S. Jacobi, R.D. Power, J.H. Cannon, C.J. du Plooy, L.B. Mcrae, C.P. Rossouw, A.L. Sillars, A.W. Heugh, R.K. Briggs, P.J. Stark, and C.S. Stott. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1993

1. Book reviews Phosphate rock, a bibliography of world resources. London, Mining Journal Books Limited, 1984. £10 (surface mail), £12.25 (airmail). Reviewer: P.Le. Grubb Ok Tedi, by William S. Pintz. London, Mining Journal Books Limited, 1984. 206 pp. £19 (surface mail), £22.25 (airmail). Reviewer: R.P. Plewman 2. Publications of the Canadian Mineral Policy Sector Lime by D.H. Stonehouse. 5 pp. Phosphates by G.S. Barry. 9 pp. Statistical summary of the mineral industry in Canada. 77 tables. Talc by M. Prud'homme. 6 pp. Zirconium by M.A. Boucher. 6 pp. Cement by D.H. Stonehouse. 13 pp. Gypsum and anhydrite by D.H. Stonehouse. 7 pp. Regional review by T.M. Buch. 12pp. SaltbyG.S. Barry. 7pp. Silicon, ferrosilicon and silicon carbide by D.G. Law-West. 6pp. SulphurbyB.W. Boyd. 9pp. Mineral Report 31. Canadian Minerals Yearbook 1981. Available from the above address at $40.75 per copy. 3. Mintek reports Report M18D The recovery of pyrite and gold from acid-leach residues from the Merriespruit Gold Mine. (First issued Feb. 1982; reissued Mar. 1984). Report M2OD The separation of ore from Cooke into high- and lowgrade fractions. (First issued Feb. 1982; reissued Mar. 1984). Report M33D Explanatory tests on the reduction of the sulphur content of sponge iron. (First issued Apr. 1982; reissued Mar. 1984). Report M43D Beneficiation tests on andalusite-bearing shales from a farm near Thabazimbi. (First issued Aug. 1982; reissuedMar. 1984). Report M129 The determination of tin, niobium, and tantalum in pegmatite by X-ray-fluorescence spectrometry. ReportM131 The determination of copper and nickel in iron- and chromium-bearing materials by a pressed-powder technique and X-ray-fluorescence spectrometry. Report M135 The installation of a 100 kV A plasma furnace at Mintek. The selection and installation of a 100 kV A a.c. plasma Report M136 The determination of gold in activated charcoal by use of a loose-powder technique and X-ray-fluorescence spectrometry. Report M140 The effect of physical and chemical factors on the corrosivity of a synthetic mine water.

Jan 1, 1984

By I. Soto, E. Córdova, A. Anani

The new caving megaprojects that are planned to go into production in the next decade have scheduled horizontal developments at very high rates, which are difficult to achieve. Research has been conducted that seeks to model the construction times for underground developments to determine the feasibility of achieving the planned rates. However, these previous attempts do not consider all the operational aspects that make up the mine development cycle. Here, we present a discrete event simulation (DES) model that individualizes each unit operation of the development cycle to determine the construction rates that new projects will be able to attain. The developed model was applied to the New Mine Level (NML) of the El Teniente Division (DET). The results indicate that it would be impractical to achieve the advance rates scheduled in the original plans if the unit operations of the mine continue to be executed using the status quo. The metres developed after six years in the sections analysed can be significantly improved by changing the maintenance strategy for the equipment (457 metres increase), orepass availability (194 metres increase), and the initial planning sequence (1 598 metres increase). It is recommended that the mine implements a flexible maintenance strategy, defines a strategy to ensure and increase orepass availability to contractors, and makes use of current simulation tools for a more robust development sequence planning.

Oct 1, 2022

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

Ninth International Symposium TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of 14th to 19th June, 1970, follows the Computer Symposium held in Salt Lake City in September, 1969. The purpose of the Symposium is to define the role of decision-making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-have permitted us to structure it in such a way that a complete picture of the mineral industry in its public policy, corporate, financial and technological environment emerges. Topics for the sessions are: . The Public Policy Environment;. The role of Decision Making Techniques in the Mining Company; . Information Storage and Retrieval; . Markets-Forecasting, Patterns and Strategies;. Search for Mineral Deposits;. Quantification of Geological Variables;. The Mine Development Decision; Production Systems;. Planning, Scheduling and Control Systems. The sessions will be directed energetically by chairmen who have been in continuous contact with the authors, providing them with information about related papers and sessions. This symposium is sponsored by the Canadian Institute of Mining and Metallurgy, McGill University and Ecole Polytechnique. Further information may be obtained from: The 9th International Symposium. W. H. Gauvin, General Chairman, J. Elbrond, Programme Chairman. Department of Mining Engineering, Ecole Poly technique, P.O. Box 501, Snowdon, Montreal 248, Quebec, Canada. ACHEMA 1970 The European meeting of Chemical Engineering and the Achema Congress 1970 is being held at Frankfurt/Maine, from 17th to 24th June, 1970. The programme includes some 110 plenary and specialised lectures, numerous technical films, excursions, and technical discussions in front of the exhibits which form the central feature of the Achema-Exhibition Congress. Further information may be obtained from the honorary representative of Achema in South Africa, Mr F. Schilling, P.O. Box 31274, Braamfontein, Johannesburg. NINTH COMMONWEALTH CONGRESS PROCEEDINGS Publication of the proceedings of the Ninth Commonwealth Mining and Metallurgical Congress, 1969, is being undertaken by the Institution of Mining and Metallurgy, London. There will be four volumes covering papers presented at the Congress together with the discussion and author's replies, and the addresses by Sir Duncan and Sir Ronald Prain. These will be available April-June 1970. Special pre-publication prices apply to orders received before 1st April, 1970. Order forms may be obtained from Secretary S.A.I.M.M., P.O. Box 1183, Johannesburg. 6th World Congress on the Prevention of Occupational Risks This Congress, dealing with industrial accidents and occupational diseases, will be held in Vienna from 10th to 15th May, 1971. Further information may be obtained from: VI Weltkongress für Unfallverhütung, Postfach 745, A-1015 Wien, ÖSTERREICH. International Vacuum Metallurgy Conference 1970 The Vacuum Metallurgy Division of the American Vacuum Society is organizing an international meeting that will be held at the Convention Center in Aanaheim, California from 15th to 19th June, 1970. Enquiries should be directed to the Arrangement's Chairman, L. M. Bianchi, TRW Inc., 23555 Euclid Avenue, Cleveland, Ohio 44117, Tel. No. (216) 383-2111. AIME WORLD LEAD-ZINC SYMPOSIUM This symposium is being held from 21st to 23rd October, 1970, in St. Louis, Missouri, U.S.A., in conjunction with the Fall Meeting of the Society of Mining Engineers, and a Rapid Excavation Conference. In addition to local field trips to smelter and refinery operations there will be a number of extended trips of six to eight days. Information may be obtained from: Mr. John C. Fox, Secretary, Society of Mining Engineers of AI.M.E., 354 East 47th Street, New York, N.Y. 10017, U.S.A. NEW SUBSCRIPTION RATE TO THE JOURNAL As from 1st JANUARY, 1970, the subscription rate for the Journal has been increased from R12.00 to R18.00 per annum, i.e. R1.50 per issue instead of R1.00. The discount to booksellers is 15 per cent. COURSEOF THE THEORYOF THE UNIT OPERATION OF GRINDING The South African Institute of Chemical Engineers is arranging for Prof. L. G. Austen to conduct a course on the above subject in September, 1970. Interested persons should contact Dr G. S. Harrison, S.A. Institution of Chemical Engineers, A.E. & C.I., 15 Anderson Street, Johannesburg. METRICATION The S.A. Bureau of Standards has published a document entitled "Metric Scales and Units for use in the Building and Construction Industry." It has been compiled by the Metrication Committee of the National Building and Construction Advisory Council and is the first of the series of informatory documents relating to the programme for the metrication of the Building Act Construction Industry. This document is obtainable from the South African Bureau of Standards, Private Bag 191, Pretoria at 50c per copy.

Book Reviews Linari-Linholm, A. A. Occurrence, mining and recovery of diamonds.Diamond Promotion Services (P.O. Box 62349, Marshalltown, Transvaal). 1974. Rl,OO. Metal Statistics 1962-1972. Metallgesellschaft Aktiengesellschaft. 60th Edition. Frankfurt am Main 1973. 328 pages. Published by Metallgesellschaft A.G., 6000 Frankfurt am Main, Reuterweg 14, Post Box 3724, Western Germany. Symposium on underground mining equipment maintenance~1973. Institution of Mining Engineers, and Association of Mining Electrical and Mechanical Engineers. Colloquium and general meeting A General Meeting and Colloquium on 'Motivation and productivity in the mining industry' was held on May 22nd, 1974, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 170 delegates and was opened by the President at 09h25. Minutes

Jan 8, 1974