Search Documents

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By E. Laine

Rock density determinations are necessary for ore resource evaluations from estimated block grades in g/t. Rock density depends on the mineral composition and, thus, it is specific for each rock type. The rock density distributions for different rock types are often symmetric. Hence, the arithmetic mean is a good approximation for the average density for lithological units. However, there may exist spatial variation in density values due to alteration, fracturing and original heterogeneities such as layering. This study compares the kriged density model with the one with constant density values for different lithological units in the evaluation of metal amounts in rock blocks. The case study consisted of rock densities measured from the drill cores at Ahmavaara PGE deposit in northern Finland. The used Ni contents were simulated in accordance with the spatial distribution of rock densities. The Ni amounts in 2x2x2 m3blocks are higher for the kriged densities than for the average densities. The difference is increasing with the increasing metal amounts due to the nonlinear correlation between Ni content and rock density. The final effect on the resource estimation depends on the cutt off grade and prices of the metal, for example, for a very valuable metal the small differences are significant

Jan 1, 2003

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By D. Chetty

The characterization of platinum group minerals (PGMs) from concentrator flotation circuits provides valuable information towards understanding PGM recovery under given milling and flotation conditions. Additional mineralogical characterization also provides information on ore variability, which may affect recovery. Considering the low grades involved, automated scanning electron microscopy (SEM) characterization of PGMs has enabled relatively quick analyses, compared with older, time consuming and less accurate optical microscopy methods. Over the years, parameters, such as species, size distribution, liberation, gangue and base metal sulfide (BMS) associations, have been used to characterize the PGMs in a process mineralogical context, to aid metallurgical interpretation. This paper considers whether flotation indices determined for PGMs can be empirically validated, using initial results from analysis of PGMs in a concentrate bank from a South African concentrator treating UG2 ore from the western limb of the Bushveld Complex. The aim is to determine whether floatability is adequately described by these parameters, or whether other mineralogical factors must be considered when assessing PGM floatability, and hence accounting for recovery vs. losses to tails. The data obtained to date, show that flotation parameters (including liberation index, BMS/gangue relationships and size distribution) have merits where large changes in PGM concentration occur, as observed in the first four cells of the concentrate bank. Larger data sets, however, are required to assess floatability, particularly where concentrate cell grades are similar, as observed in the last six cells of the concentrate bank. Furthermore, the floatability indices could be enhanced by the incorporation of selected associated gangue mineral information, chief amongst these being the content and mode of occurrence of naturally floatable talc and associated orthopyroxene.

Jan 1, 2009

By E. Eccleston

The ConRoast process for the production of platinum group metals involves the use of a fluidized bed reactor for the removal of sulphur from ore concentrates by roasting prior to smelting in a DC-arc furnace. Test work was carried out in 2007 at Hazen Research in Golden, Colorado to provide the data necessary for a commercial roaster to be designed by Technip. This paper discusses the rationale behind the test work, the goals for calcine composition to be used as smelting furnace feed, the results of various roaster operating parameters in terms of calcine composition (particularly residual sulphur and the fate of trace elements), and the impact of the results in terms of a commercial roaster design.

Jan 1, 2009

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By G. R. Lane

A large opencast gold mining company in Africa had just completed a feasibility study for an expansion of the operations. A traditional net present value project valuation methodology had been used that showed a very positive net present value (NPV). The project team had conducted a qualitative risk assessment that identified and logged all potential project risks and had subjectively incorporated 'risk' via the discount rate and other assumption contingencies around gold price expectations, operating parameters, etc. Management requested that an independent quantitative risk modelling approach be adopted to obtain a better understanding of the impact of risk on the overall project valuation and confidence level in the final valuation. A detailed project valuation model was configured in the Cyest Carbon Modelling Technology platform, and the stochastic modelling module used to perform the Monte Carlo simulations. Analysis of historical operational performance data relating to actual achievements versus planned and budget determined the historical variability of the underlying parameters as well as variance to budget. This was done at a detailed level for mining rates and costs, processing rate, costs and recovery, and other operational efficiency measures. External market assumptions relating to gold price, exchange rate, and inflation were modelled and the dependency between them modelled using a copula. This case study will demonstrate the approach taken to building and populating the quantitative risk model and the overall results of the Monte Carlo simulation. The final valuation demonstrated that the project had a 44 percent probability of an NPV less than zero i.e. a 44 percent chance of project finance loss.

Jan 1, 2013

By S. Y. Chen

A new process comprising metallizing reduction, magnetic separation, and electroheat melting separation is proposed with the aim of achieving high recoveries of iron, vanadium, and titanium from vanadium titanomagnetite. The effects of magnetic intensity, reduction temperature, reduction time, carbon ratio, and coal particle size on the efficiency of reductionmagnetic separation were investigated, the reaction mechanisms elucidated by SEM and EDS analysis, and the optimal process parameters established. Recoveries of up to 80.08% for titanium, 95.07% for iron, and 71.60% for vanadium were achieved. The reduction sequence is shown to be: Fe2O3 ? Fe3O4 ? FeO ? Fe; Fe2TiO5 ? Fe2TiO4 + TiO2 ? Fe + FeTiO3 ? Fe + FeTi2O5 ? Fe + TiO2.

Jan 1, 2014

By N. Z. Jovanovic

Irrigation of agricultural crops may be a cost-effective option for the utilization of gypsiferous minewater as it may also create an opportunity to produce crops during the dry winter season on farm sin South Africa, such as in Mpumalanga. In this study, intensive field monitoring systems were developed and implemented to assess the feasibility and sustainability of irrigation with gypsiferous mine water. Soil water and salt balance components, as well as crop yields, were monitored in field trials carried out at Kleinkopjé and New Vaal Collieries (Anglo Coal), and at Syferfontein (Sasol). Field measurements indicated that high crop and pasture yields can be obtained, provided fertilization and irrigation water management are appropriate. Soil water and salt balances indicated that considerable amounts of minewater can be used and considerable masses of salts can be removed through precipitation of gypsum in the soil profile. With appropriate management, water and salt runoff and salt leaching can be intercepted, thereby minimizing the impact on groundwater. The SWB model is being validated through on-going monitoring. This will allow the use of the SWB model at other sites to predict the long-term impact of irrigation with mine water on soil and groundwater, as well as to run scenario simulations in order to recommend sustainable management of irrigation with minewater.

Jan 1, 2004

By D. J. de Beer

South Africa had a late start with rapid prototyping (RP), with the first system being available in 1991. Up to 1994 only three systems were available in SA. Through active research participation from the CSIR and a number of universities, supported by technology transfer programmes and industry awareness workshops, adoption of RP technologies started to grow. Internationally, RP grew to the extent that several country-based member organizations were formed, and an initiation meeting of the Global Alliance of RP Associations (GARPA) took place during the SME Rapid Conference in Dearborn, USA in 1998. South Africa (SA) was invited under the auspices of the Time Compression Technologies Centre (TCTC) launched by the CSIR, and received an invitation to become a member of GARPA through the launch of a national, inclusive organization. The latter gave rise to a RAPDASA planning/launch meeting held at the University of Stellenbosch, which culminated in the first RAPDASA international conference held in November 2000 at the CSIR, and the election of a first RAPDASA management committee, also at the 1st AGM held during the conference. RAPDASA has been a pillar of strength since then, with an annual international conference being presented. As South Africa?s RP awareness grew through the RAPDASA and independent activities, so did the availability of RP platforms in SA.SA also became a benchmark for other countries/late adopters to follow, as slowly a position of following became a position of leading through innovative applications. The paper highlights SA?s development approach and history, together with the discussion of case studies in various fields. Contribution to the light metals industry will also be discussed. Keywords Rapid prototyping, additive manufacturing, product design, rapid tooling, rapid manufacturing, medical product development.

Jan 1, 2011

By N. Sahay

Open fire in coal mines is one of the most serious threats to miners, as well as to the mine. Open fire can often be effectively dealt with by prompt local action, otherwise it very quickly becomes uncontrollable. In one incident, none of the available open fire control technologies, viz., water deluge and sprinkler systems, high-expansion foam, high-pressure high-stability nitrogen foam, water misting, and ventilation and pressure control techniques, were effective for saving the mine without sealing from surface, since the fuel-rich environment prohibited underground access due to the methane explosion hazard. The authors have developed a methodology for dealing with advancedstage open fires underground by the application of a modified ventilation control technique. It is based primarily on a better understanding of the behaviour of open fires, proper diagnosis of the problem, application of judicious ventilation control techniques, and selection of suitable fire indices for assessing the status of an open fire. This methodology was used to successfully control an open fire in Surakachhar 3 and 4 incline mine Surakachhar, central India. The fire area was sealed underground and production subsequently resumed in record time. The paper discusses the behaviour of open fires, particulars of the mine, diagnosis of the problem, experimentation methods, and the results obtained.

Jan 1, 2014

By J. L. van Niekerk

The proposed Gautrain Rapid Rail Link (GRRL) will require approximately 15 km of double or twin high-speed rail track tunnels located for the greater part beneath the northern suburbs of Johannesburg, including Houghton, Rosebank and Sandton. During the Environmental Impact Assessment (EIA) it became clear that potential surface vibration above and in the vicinity of the tunnels was a matter of serious concern to the residents of the affected properties and that the impact required assessment. The general method proposed is based on a US Department of Transportation, 1998, publication in which abase vibration curve derived for typical high-speed passenger trains is adjusted for the topological, geological and other features to predict the surface vibration and the associated ground-borne noise. The predictions indicate that some isolated areas might be impacted but that the impact will likely be limited, and it is possible to mitigate the impact using suitable track construction methods and track support systems.

Jan 1, 2004

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By R. M. Tyler

The importance of the heavy mineral sands to southern African economic well-being cannot be over emphasized. The value of the worldwide titanium dioxide industry is estimated at $7 billion. Six out of eight of the world?s proposed new project areas are in southern and eastern Africa, and a seventh at Tamil Nadu in India is partly owned by a South African company, Kumba Resources. The HMS industry can be highly lucrative; its return on capital is the best in the mining industry. There are, however, problems, particularly in the smelting technology. The often considerable affect of mining on environmentally sensitive coastal dunes is also becoming increasingly important. The medium-to long-term demand for Ti-dioxide pigment and ceramic grade zircon appears very healthy. If, as predicted, the costs of producing titanium metal can be reduced, then there is huge potential for the metal. In summary, the HMS industry is an attractive one to be in, with good returns and generally manageable risks. New business opportunities and their economic implications for Africa are discussed.

Jan 1, 2004

Although not fully accepted in South Africa, the Theory of Sampling originally proposed by Pierre Gy is fast becoming the cornerstone of sampling practice throughout the world. The growing acceptance of Gy?s Theory of Sampling in South Africa can be attributed to a number of factors, chief amongst them being the development of a tradable mineral asset market, the promulgation of the Mineral and Petroleum Resources Development Act (MPRDA), the growing number of commercial and academic courses that are offered on sampling, and the regulation of the industry through internationally acceptable guidelines and rules for reporting and trading in mineral assets. The size of the South African minerals industry and the dependence of our economy on mineral production have also meant that correct sampling is of key importance to mineral trade. ISO standards have been the principal guides for producers of mineral bulk commodities who produce to customers? specifications, whereas Gy?s insights have been most readily accepted by precious and base metals producers whose product is sold into metal markets. Understanding of small-scale variability is essential in the precious and base-metal industries, but detailed studies of the effects of heterogeneity have not been as productive in the bulk commodities. Sampling practices at different stages of mineral development from exploration, face sampling and grade control, ore processing and handling, metallurgical sub-sampling, point of sale sampling, and sampling in the laboratory are considered in the gold, platinum, ferrous metal, and coal industries. A summary of the impact of poor sampling in these industries is presented. Generally it appears that poor sampling practice is most likely to erode mineral asset value at the early stages of mineral development. The benefits of good sampling are considered, especially with regard to the financial implications of bias and error on large and consistent consignments of bulk commodities. Keywords theory of sampling, sampling errors, ISO standards.

Jan 1, 2014

By M. R. Bitarafan

Mining method selection is the first and most important problem in mine design. In this selection some of the parameters such as geological and geotechnical properties, economic parameters and geographical factors are involved. The mining engineer must balance the input parameters and select the method that appears to be the most suitable; mining method selection is both an art and a science. Distinguishing all parameters that have an effect in mining method selection and in the determination of weighting factors of any parameter is a difficult task in an ordinary environment. This paper attempts to determine important parameters that impact on the mining method selection and demonstrates the calculation of the weighting factors for each selected parameter. This study has been directed to the research of a methodology for the selection of an optimal mining method. Different fuzzy methods are presented as an innovative tool for criteria aggregation in mining decision problems. Two methods of fuzzy multiple criteria decision making are used for selecting the optimal method with which to mine anomaly No. 3 of the Gol-Gohar iron mine. This paper finally presents a comparison of the selection methodologies and further discusses the most appropriate method investigated.

Jan 1, 2004

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015

By C. L. Reichardt

Mining companies are increasingly looking to the developing world for the next generation of mining projects, often in countries that have little or no previous history of large-scale mining. One of the major challenges for such projects is hiring?and retaining?personnel that have technical skills and experience in mining-related disciplines. Staffing a mine with an expatriate workforce is neither cost-effective nor sustainable, and many countries now insist that mining companies ?transform? the profile of their workforce to more closely mirror the demographic profile of the host population. The need to nurture mining-related skills in emerging mining nations is not solely limited to the workforce: there are also pressing economic and sustainability imperatives to develop capacity within local service providers such as consultants and contractors, as well as to facilitate informed engagement between mining companies, government and civil society. However, few educational institutions in emerging mining nations currently have the ability to offer practical training in mining-related disciplines. Local employees who are sponsored by companies to develop their skills through international study maybe impeded by language and cultural barriers, and may also be taught using course content that is of limited relevance to the specific challenges of their future working environment. This paper addresses the challenge of skills development and retention in emerging mining nations and uses examples from sub-Saharan Africa and the Asia Pacific region to explore practical means of developing capacity in mining-related disciplines. It examines the need for companies to implement strategies to develop local technical capacity in countries where they envisage a long-term operational future and also highlights the need to foster partnerships between academia, developmental institutions, mining companies, governments and civil society to establish the critical mass of mining-related skills required to nurture the development of a sustainable mining industry.

Jan 1, 2009