Search Documents

Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to the company's industry peers in the platinum group metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that resulted from milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tapblock movement, the formation of three-phase 'mushy' zones, high refractory and taphole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to redesign Furnace No. 1, to invest in backup furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line monitoring of feed chemistry and mineralogy, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilizing optical spectral analysis of the converter flame to characterize converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

By G. H. Lind

This paper discusses the traditional costing approach currently used in the underground coal mining industry. Activity Based Costing (ABC) is identified as being a potentially more effective manner in which to cost underground coal mining systems. With the use of a costing framework developed by the author incorporating new thinking to eliminate the shortcomings identified in the traditional costing approach, a comparison of two types of underground coal mining systems, viz. continuous miner and longwall, is conducted. It is found that under certain criteria, in all cases, irrespective of the way in which the systems are costed, the continuous miner system is currently the better investment. It is also observed that when a system is costed using ABC that better investment decisions result when compared to costing the same system using traditional costing techniques. It is further seen that traditional costing techniques tend to overestimate the total costs of a mining system. This paper shows one application of ABC that can be incorporated as a management tool.

Jan 1, 2001

By R. T. Jones

The 20 Mt reverberatory furnace slag dump at Nkana in Zambia contains a substantial quantity of cobalt. A 40 MW DC arc furnace has been built at Chambishi for the purpose of recovering cobalt from the slag. The technology was jointly developed by Mintek and Anglovaal Mining Ltd (Avmin), and the furnace was designed by Bateman Titaco. Testwork at the 150?250 kW scale was conducted at AVRL, and larger scale piloting was conducted at Mintek (in partnership with Avmin) in a 3 MW DC arc furnace. Approximately 840 tons of Nkana dump slag (ranging from 0.66% Co) was processed at power levels around 1-2 MW. Good overall cobalt extraction was achieved, and approximately 100 tons of cobalt-bearing alloy was produced (containing 5 to 14% Co). This testwork demonstrated that the Nkana dump slag could be processed in a DC arc furnace of suitable design, to produce a cobalt-bearing alloy suitable for further hydrometallurgical processing. Bateman Titaco were contracted to design and build the furnace, and the design team contained representatives from Avmin and Mintek. The project was conceived as a fast-track exercise, and many activities had to be run in parallel. Notable features of the furnace include an ABB power supply, a Concast conductive hearth, the refractory design, and copper cooling in the sidewalls. Power to the furnace was switched on during January 2001.

Jan 1, 2002

By X. Yu

Although many investigations of the deformation behaviour of rocks have been carried out, most of them are carried out in compression. In all rock engineering practice it is usually assumed that the deformation of rocks in tension is the same as that in compression. However, data from numerous researchers have shown that this assumption is not correct for some rocks. A new loading frame for testing rocks in compression and direct tension has recently been developed by the authors, with the capacity to conduct both compression and tensile tests on the same rock sample. The results obtained show that the ratios between the average Young?s modulus in compression (ECA) and in direct tension (ETA) are 1, 1.16, 2 and 6 respectively in four rock types tested. For Poisson?s ratios, analogous relations were obtained. It was observed that, in all cases, the tangent Young?s modulus intension reduces with an increase in the applied tensile stress, while the behaviour of Poisson?s ratio is similar, but shows greater variability. The difference between the Young?s modulus of rocks in tension and that in compression could lead, large errors in calculating induced stresses around underground openings, as well as in determining the Brazilian tensile strength of rocks. This may have a significant influence in rock engineering and therefore more investigation is necessary into the tensile deformation behaviour of rocks and its influence.

Jan 1, 2005

Bacterial leaching represents an unusual problem in biochemical engineering, because the substrate for bacterial growth is not supplied directly, but is a product of another reaction, the leaching of mineral particles. Leaching arises from the bacterial oxidation of ferrous ions to ferric ions, which in turn oxidize the mineral. For the bacterial dissolution of pyrite, these reactions are: [ ] (Y represents a stoichiometric yield factor, and N represents the amount of bacteria.) Equations [1] and [2] represent a cyclic auto-catalytic system since more ferric ions are added to the system with an increase in the extent of leaching.

Jan 1, 2000

By J. H. Potgieter

This paper describes an investigation to separate and selectively recover silver, gold and platinum from jewellery and laboratory wastes, and produce technical grade material suitable for training purposes. Nitric acid was employed to dissolve and separate silver and other impurities from gold and platinum, which were then dissolved in aqua regia and precipitated selectively. The current work quantified the effects of temperature, stirring rate, leaching agent concentration and solid: liquid ratio on the recovery of the various noble metals and in summary yielded the optimum treatment conditions in each case. It was found that increased leaching reagent concentration (in the case of Ag), temperatures and stirring rates enhanced the recovery kinetics and optimum yield of the three noble metals. An increased liquid to solid ratio also enhanced the recovery of the silver. Recovery yields 97.1%, 99.9%and 99.4% for silver, gold and platinum, respectively, were obtained. The recovered silver, gold and platinum had purities of, respectively, 98.3%, 99.1% and 99.0%. A cost saving of approximately R10 000 per kilogram of scrap refined could be achieved by the in-house treatment of the waste, not to mention the time-saving benefit.

Jan 1, 2004

By O. Naiker

Xstrata has modified and improved on the solid state reduction of chromite (SRC) process that was pioneered by Showa Denko in Japan and previously used at Xstrata?s Lydenburg plant. The history of pre-reduction is a long one, with the SRC process being the first and only commercially successful one prior to Premus. Krupp developed the chromite direct reduction and the rotary hearth for the pre-reduction of chromite. However, these processes have not been successfully commercialised. The are a number of significant differences between Xstrata?s patented Premus and the original Consolidated Metallurgical Industries (CMI) process. These include, the use of lower cost anthracite fines as the reductant source together with the use of unactivated bentonite as the binding agent. In addition the use of oxygen as an energy source is used in Premus but not in the original CMI process. There was a fundamental change in the operational philosophy of the process in that while the original CMI process aimed to maximize metallization of the pellets, the Premus process seeks to maximize the energy output from the kiln while still achieving the required efficiencies and hence increasing furnace output. Premus is designed to reduce electrical energy consumption, provide high recoveries of metallic oxides, and utilizes low cost reductant and energy sources such as anthracite and oxygen respectively. Due to the fact that Premus is one of the most technologically advanced and competitive processes used today in the production of ferrochrome it was the process selected for Xstrata?s new ferrochrome facility, Project Lion, that is due to be commissioned in the third quarter of 2006 in the Steelpoort Valley in Mpumulanga, South Africa.

Jan 1, 2007

By C. -J. Rick

By implementing a converter downstream of the reduction furnace it is possible to broaden the product range significantly. The converter can also successfully be used to strip furnace slag from chromium oxide. Some process alternatives and their economical, practical and environmental implications are studied using process models developed based on UHT?s long experience in stainless steelmaking, stainless steel process control and charge chrome refining. Keywords Charge chrome, converter refining, ferrochromium products, process design.

Jan 1, 2010

By A. Singh

The control of flotation plants is by no means trivial. Flotation is one of the most interactive minerals? processing operations. The interactive nature of flotation circuits results in oscillations of levels and hence of grades and recoveries. Also, poor level setpoint tracking and disturbances have negative influences on grades and recoveries. The result is an unstable plant with limited scope for optimization. An advanced controller, FloatStarTM, has been developed to provide tight control and to reduce the amount of disturbances in flotation levels. It has been shown on a number of plants that the system results in faster and better setpoint tracking, better regulatory control and faster settling times after start-ups and disturbances. The successful stabilization provided by FloatStar has made it easier to investigate the area of optimization on flotation circuits. Mintek has identified the need for a more meaningful set of setpoints or aeration rates to use as a basis for control than levels and have advocated flow control by looking after residence times. When the feed conditions change, the ideal solution would be an algorithm or strategy that finds the new optimum conditions rather than just having an unguided hunt from the previous point. A multivariable flow-optimizing algorithm, a new module in FloatStar, has been developed to calculate optimum level setpoints and/or aeration rates that will aim to optimize the residence times, mass pulls and circulating loads within a flotation circuit. Keywords: flotation, regulatory, FloatStar, start-up, disturbance, residence times, circulating loads

Jan 1, 2003

By B. Elevli

The aim of this paper is to demonstrate the implementation of multicriteria analysis in selection of the most suitable underground ore transport system for a chromite mine in Turkey. The related problem includes five possible ore transport systems and six criteria to evaluate them. The adopted evaluation and ranking method for this study is PROMETHEE. PROMETHEE I revealed a partial order of alternatives where incomparability exists. PROMETHEE II gave the absolute ordering of alternatives. The results have shown that the PROMETHEE method can be successfully used in solving mining engineering problems. Keywords: multi-objective, decision analysis, mining, ore transport system

Jan 1, 2004

By S. Luyckx

This paper reports hardness and abrasive wear resistance test results from a wide range of WC-Co alloys, varying in cobalt content as well as WC grain size. The results show that the abrasive wear resistance increases with increasing hardness and that the rate of increase is higher for larger WC grain sizes. The increase in abrasive wear resistance was found to be parabolic up to a critical hardness value and exponential above that value. The transition from parabolic to exponential behaviour was found to occur at the same contiguity value for all grain sizes, which suggests that at that contiguity value the WC skeleton becomes continuous in all WC-Co alloys.

Jan 1, 2004

By J. C. Jansen

The platinum mining industry has experienced a significant increase in fatal accidents. Mine accidents are in principle preventable, and there is enormous pressure on employers to reverse this trend. This paper reviews safety management systems (SMS) as well as behaviour-based safety (BBS). Based on the review, SWOT analyses are performed on the SMS and BBS processes and a model of an integrated safety management system (ISMS) is introduced. A number of fatal accidents is analysed to identify factors that contributed to accidents in the mining industry. Thereafter the potential weaknesses of an SMS of a platinum mine are exposed and the potential benefits of implementing the ISMS for this case study are demonstrated.

Jan 1, 2005

By Rodney Ishak, Merete Tangstad

In the HC FeMn production, better utilisation of coke and electric power is vital for reducing the production costs. The higher manganese oxides in the charge are reduced to MnO in the prereduction zone, where also the Boudouard reaction is active. These gas-solid reactions are to a large extent decisive for the total consumption of both coke and electrical power in ferromanganese production. In the present work formulas for calculating the Degree of prereduction have been developed for industrial practice. It shows that the typical Degree of prereduction is between 10-40%, but it may in good periods be as high as 60%. Statistical analysis has been done in order to find how various operational parameters influence the Degree of prereduction. A few parameters were observed to have an effect on the prereduction. Comilog ore definitely had a positiveinfluence on the prereduction, Comilog sinter and Mamatwan ore probably had a positive influence on the prereduction, all in relation to the average prereduction in the selected periods. Meanwhile, As man ore definitely, % H2O in raw materials and increasing Hd probably, had a negative influence on the prereduction. The findings for these raw materials were very much in coherence with the results of laboratory scale experiments performed, where the CO-reactivity of different ore materials was studied.

Jan 1, 2007

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

By H. Saroglou

The anisotropic behaviour of Athens Schist has been brought out through the testing of specimens with varying orientation of schistosity with respect to the major principal stress under uniaxial, triaxial and dynamic conditions. A large number of results from tests on intact rock specimens of the Athens Schist were statistically analysed and evaluated.

Jan 1, 2004

By S. Dalton

The use of coal for power generation is being questioned in many developed countries, as a result of ever-tightening environmental restrictions and concerns about the potential impact of CO2emissions on climate. Coal will continue to be the fuel of choice for new power plants for many developing countries with large percentages of the world?s population, because of its relatively low cost and broad availability. Even in many of the developed countries that are under pressure, coal will continue to fuel large percentages of power due to the installed base. Using coal efficiently and in an environmentally responsible manner will be a challenge for technology and politics in this new century, with the politics played out on the world stage. Coal use will vary in the next few decades, including short-term changes such as the use of more diverse coals and the increased use of efficient ultra-supercritical boilers to longer term ?refining? of coal to produce a range of energy and chemical outputs. This paper outlines EPRI?s Global Coal Initiative aimed at needed developments and demonstrations that support the long-term vision of environmentally sound and economical coal use for power generation, and discusses some of the forces that are driving this development effort.

Jan 1, 2001

Council for 1999/2000 President M.H. Rogers President Elect Dr L.A. Cramer Vice Presidents Senior A.A.B. Douglas Immediate Past President J.R. Dixon Junior S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2000

By M. van Schoor

The bulk of the world?s platinum production originates from the Merensky and UG2 reefs within the Bushveld Complex, South Africa. Both the Merensky and UG2 reefs are disrupted by faults, dykes, potholes and iron-rich ultramafic pegmatite bodies (IRUPs)?features that impact negatively on production, planning and safety. It is therefore advantageous to know of their presence and geometry ahead of mining. To date, no geophysical technique has been successfully applied to the routine mapping of mine-scale potholes and IRUPs. These disruptive features may vary from a few metres to several tens of metres in diameter. In this paper the applicability of in-mine electrical resistance tomography (ERT) to map potholes and other disruptions to the continuity of the Merensky and UG2 reefs ahead of mining is demonstrated using two case studies.

Jan 1, 2005

Changes in reductant and energy inputs which are required to adjust the slag composition in an ilmenite smelter to a higher or lower FeO content are calculated. The calculated changes are based on the assumption that solidification equilibrium with the freeze lining constrains the slag composition to follow a eutectic groove in the TiO2-FeO-TiO1.5phase diagram. Calculated equilibrium conditions along the eutectic groove are presented, and form the basis of the calculations. The inputs of energy and carbon need to deviate strongly from the steady-state values to adjust the slag composition. The inputs required at any given time depend on the desired rate of change of the slag composition, and the current slag composition. The steady-state relationship of a change in energy input of 5 kWh corresponding to a 1 kg change in carbon input also holds for the changed inputs during transient changes in FeO content. Keywords: Ilmenite smelting, freeze lining, solidification, eutectic

Jan 1, 2003