Search Documents

By L. B. Rothfeld, R. L. Dolzani

This paper presents preliminary results of a US Bureau of Mines (USBM) study of potential costs of compliance with possible federal regulations for copper heap and dump leaching. The regulations could arise under amendments to the Resource Conservation and Recovery Act (RCRA) and/or the General Mining Law. Estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the cost of compliance with 1992 state requirements for terrains typical of those found at existing copper leach sites in the southwestern United States. Incremental compliance costs are found to widely exceed screening criteria used by the US Environmental Protection Agency (EPA) to denote significant economic impact.

Jan 1, 1995

By G. D. Elliot, R. L. Grayson, G. L. Winn

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate was approximately 10 times higher than the national coal-industry fatality rate. Although the number of fatalities went down from 22 in 1991 to 17 in 1992, West Virginia still led the nation in coal-mining fatalities. A team of mining and safety professionals from West Virginia, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training, studied this problem. A clear path for formal intervention was determined and is presented here.

Jan 1, 1996

By Craig J. Nelsen, David A. Smith

In 1987, LAC Minerals (USA), Inc. conducted a high resolution helicopter electromagnetic (EM) and magnetic geophysical survey on the Ortiz Mine Grant, New Mexico. The primary purpose of this survey was to assist in geologic mapping of a major structural zone, the Tijeras-Canoncito Fault System (TCFS). This structure is a very important ore- controlling feature in the area. Geophysical signatures over known deposits was a secondary goal of the survey, but direct detection of mineralization was not anticipated. The TCFS was revealed to be a complex, branching and anastomosing system of faults which locally form the bounding structures of a graben. The geophysical survey guided subsequent geologic mapping by redirecting field investigations, and geophysically redefining some features which previously had been only partly defined.

Jan 1, 1989

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

By J. A. Nelen, R. B. Cook

Panned stream-sediment, geochemistry-based gold exploration in those parts of the southeastern Piedmont proximal to the Fall Line must take into account potential contamination from basal fluvial sediments of the Coastal Plain. Anomalies attributable to the incorporation of placer gold of Coastal Plain origin into modern Piedmont drainages have been identified in portions of Lee, Macon, and Tallapoosa Counties, AL, and Baldwin and Hancock Counties, GA. Identification and interpretation of such multicyclic anomalies must be based on knowledge of the local maximum Cretaceous transgression, paleotopography, modern and paleofluvial system dynamics, and fineness trends and Au-Ag zoning in gold grains.

Jan 1, 1990

By J. S. Stachulak

Installation of a computerized mine monitoring and control system in two planned construction phases began in 1983. Phase one consisted of providing a central monitoring station located on surface for monitoring underground CO detection in Frood Mine's heated area. The implementation of this project annualized labour savings of $200,000. The cost of installation of an early fire warning system was $100,000. There are several CO sensor monitoring carbon monoxide trends through mine heated areas. To obtain an early warning, it is not good enough to know that a fire has started, but it is also necessary to know where the fire is located.

Jan 1, 1989

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A low-temperature-chlorination selective oxidation followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide was investigated for hydrometallurgical processing of a chalcopyrite concentrate. In this article, the selective oxidation phase of the process is described. The selective oxidation requires a temperature well above the CuCl-FeCl3 eutectic points. The test procedure was developed with a batch reactor and then tested with a continuous reactor. The process was initiated by adding small amounts of chlorinated samples to a fluidizing bed of dead-roasted sulfide concentrate micropellets. The selectively oxidized samples thus prepared were shown to fully dissolve copper, while virtually all the iron remained undissolved.

Jan 1, 2000

By Subash Chander, B. Arnold

Many developments have occurred in coal flotation with regard to increasing recovery from the flotation circuit and its impact on overall coal preparation plant recovery. This includes innovative design of flotation circuits, equipment modification and development, methods of enhancing the use of reagents, effect of slimes, and recognizing the effect of water chemistry. This paper will review recent advances and present some guidelines to improve process efficiency.

Jan 1, 2005

By L. Xu, R. Bhaskar

While a NIOSH accepted procedure exists for determination of quartz in the respirable dust samples from coal mines, no specific procedure has been defined for quartz determination in bulk samples. In this study, the effect of particle size on the estimation of quartz using the infrared technique was evaluated. Several laboratory tests were performed to determine the dependence of the infrared absorbance peak height on the different sizes of quartz particles. The significant dependence observed between quartz particle size and the measured peak height indicates the potential for erroneous interpretation of the quartz in bulk samples depending on how the samples are prepared. A procedure to reduce the effect of size in the determination of the quartz content is suggested.

Jan 1, 1994

By P. Somasundaran, C. C. Harris

The power consumption of stirred-media mills was studied using an approach developed from work on stirred reactors. Evaluated were the relationships of factors such as stirring speed and impeller and tank dimensions on the torque required to rotate disc and pin impellers immersed in dense particulate media. Data collected under carious experimental conditions were analyzed. The results were summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention was directed towards the rheological properties of the media, which was considered a non-Newtonian liquid, and hence the equation of power-law liquids was employed. A procedure for estimating the parameters of effective viscosity and scale-up guidelines (with respect to power consumption) are proposed.

Jan 1, 1996

By J. J. Kellar, W. M. Cross, H. Du, C. D. Struckman, D. A. Boyles

Silane coupling agents have been used in the filler industry for years. One particularly unique feature is the ability of the coupling agents to enhance the adhesion between filler and polymer matrices. This paper will review the use of coupling agents for polymer matrix composite applications and discuss a new approach to coupling agent chemistry, namely, direct formation of a silicon-carbon non-hydrolyzable linkage between glass and coupling agent. The grafted silane monolayers were evaluated by infrared spectroscopy to ascertain their surface coverage and relative stability. Finally, composite specimens were fabricated and their mechanical properties were compared with traditional silane coupling agent treatment.

Jan 1, 2003

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to pining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1992

By Abdullah Arik

In deposits with highly skewed grade distributions, such as precious metals deposits, proper handling of the outlier high grade data is very crucial to the ore reserve estimation. Although some recent geostatistical techniques are available to handle the estimation problems with these outlier data, ordinary kriging or conventional methods are still widely used to estimate the ore reserves for such deposits. One reason for this is the fact that the alternative methods offered are either too complex or too exhaustive for the mine engineers and geologist who often do not have the expertise or the time to apply these methods. This paper presents a new 2-step kriging algorithm "Outlier Restricted Kriging" (ORK) which can be a simple and a practical tool to use where the ordinary kriging will fail to handle the outlier high grade data properly in block grade estimation. The paper details the methodology and discusses the results of its application to a gold deposit.

Jan 1, 1992

By J. D. Miller, D. M. Catarious, F. L. Stanley

The quality of cleaned products from coal preparation plants is often variable due to natural fluctuations in the washability characteristics of the plant feed. To combat this problem, many modern plants have installed on-line analyzers that provide feedback for the real-time control of product quality via the adjustment of circuit cutpoints. Unfortunately, optimization studies show that this approach may actually lead to increased losses of saleable coal. This paper discusses the problems associated with the real-time manipulation of circuit cutpoints and suggests alternative modes of operation that are better suited for plant optimization. A case study involving an eastern U.S. coal plant has been used to compare the economic impacts of these different approaches for plantwide control.

Jan 1, 2000

By L. G. Austin, R. C. Klimpel

Batch breakage kinetic tests were performed in a mill of 0.3 m diameter for a range of mill conditions. Accurate simulation required the measurement and use of factors which accelerated the specific rates of breakage of the top sizes as finer material accumulated in the slurry. These factors depended on the size distribution expressed relative to the top size, not the absolute size, suggesting that they are due to a packing effect not a rheological effect. The data simulated correctly a series of steady-state continuous tests in a mill of the same diameter providing values were corrected to the hold-up, ball load, slurry density, and size distribution measured in the continuous mill tests.

Jan 1, 1990

By J. A. Organiscak

This paper examines methods for limiting occupational silica exposures for roof bolting personnel in underground coal mining. A canopy air curtain and an air tube were evaluated as means to provide filtered air over the breathing zone of these personnel. Laboratory testing showed that dust reductions beneath the air curtain and air tube approached 60 percent and 40 percent, respectively, with low interference air velocities. The data also showed that dust reductions were highest for positions closest to the device and that these levels decreased with distance. This paper also evaluates a metal rake, a flexible insert, and a rigid insert for cleaning the roof bolter dust collector box. Less dust was produced when using the rigid insert. Surprisingly, the flexible insert was sometimes no better than scraping or raking the dust onto the mine floor. However, little dust got on the coveralls when using either of the inserts.

Jan 1, 2002

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger's, Kick's and Bond's laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By Arpad E. Torma

The introduction of biotechnological principles in hydrometallurgy has created new opportunities and challenges for the industry of mineral processing. During the 1950's and 608s, the mining wastes and unused complex mineral resources have been successfully treated in bacterial assisted heap and dump leaching processes, especially for the production of copper and uranium. The economic viability of bio- leaching technology lead to its world-wide acceptance by the mining industries. During the 1970's this technology grew into a more structured discipline which is called "biohydrometallurgy". Currently, bioleaching techniques are ready to be used, in addition to copper and uranium, for the extraction of cobalt, nickel, zinc, gold and silver from diverse mineral resources and for the desulfurization of certain coals. However, in a foreseeable future the biohydrometallurgical processes may be applied also for the treatment of high- grade ores and mineral concentrates using native and/or genetically engineered microorganisms.

Jan 1, 1989