Search Documents

By Andrew Neale

ERIC GUTIERREZ: With that, we'll go ahead with the final speaker of the day, Andrew Neale. Andrew has a master's of science degree in mineral processing from the University of Alberta. He worked at the Falconbridge in Sudbury area, also at Brenda Mines, and then he became part of the Brenda Process Technology group in British Columbia. He joined Freeport in late 1993 in Indonesia, and was involved in process control and automation. He is now the senior manager of metallurgy in New Orleans. He's responsible for designing Freeport's new 100,000-ton-per-day expansion concentrator, which is currently being commissioned. Please welcome Andrew. ANDREW NEALE: With the ongoing explosion in digital computing power, there seems to be no limit to what can be modeled, simulated, and controlled in the mineral processing plant. However, at each stage of development of a control system, it is necessary to complete a cost-benefit analysis for justifying the move to a higher level of control. Incremental improvements in plant performance, while often significant, must be weighed against the costs of implementation and long-term maintenance. This presentation will provide examples of what the author believes are misplaced or misguided process control efforts and make a case for the KISS principle as applied to process control.

Jan 1, 1998

By Jesse L. . Jr. You

Tunnels in the granitic Climax stock at the Nevada Test Site were inspected for keyblock occurrence. Thirteen relatively large pyramidal keyblocks were located in about 230 m (750 it) of tunnel. Orientations, dimensions, joint roughness coefficients, and joint compressive strengths were measured for the faces of nine keyblocks. The measurements were used to back-analyze keyblock stability to check the validity of a numerical model for keyblock behavior. A newly developed three-dimensional numerical model correctly predicted whether or not each keyblock failed in six of eight cases. The two exceptions involved stress conditions and keyblock locations that clearly violated the assumptions that underlie the stability model. The observations also allowed the effect of tunnel orientation on keyblock occurrence to be evaluated. Of the thirteen observed keyblocks, nine large blocks were found in less than 30 m (100 ft) of the Piledriver drift (which runs N56E) while only four blocks of comparable size were observed in 200 m (656 ft) of the Spent Fuel Test--Climax drifts (N61W). The orientations of the keyblock faces were checked against known discontinuity set orientations; some of the faces correlated well with mean set orientations, whi.le other faces were fringe members of sets. Stereographic techniques were used to examine the frequency of keyblock occurrence and to determine the maximum keyblock size that could be encountered with a given combination of discontinuities. Keyblock occurrence was found to be affected by tunnel orientation in a predictable way; this can be used to guide or improve tunnel design practices.

Jan 1, 1986

By J. W. Shuster

Test of trolley-diesel prime power is another step in the search to exploit the unused potential of electric wheel driven haulage trucks. The output of the present engine - a 700 horsepower diesel - is not adequate to exploit fully the 1200 horsepower potential of the two electric wheel drive motors. Power was supplied to a modified 100-ton haulage truck through a double wire trolley system. The vehicle was tested with various payloads on a 7% adverse grade haul road. More significant conclusions developed are: Power - Horsepower to propel the vehicle can he more than doubled to improve truck cycle time. Productivity - Trolley power up adverse grades can improve [producivity] rates from 18 to 36%, dependent upon haul road profile.

Jan 1, 1968

By Gustavo G. Pilger, Jair C. Koppe, João Felipe C. L. Costa

Information for mine planning requires to be close spaced, if compared to the grid used for exploration and resource assessment. The additional samples collected during quasi-mining are frequently located in the same pattern of the original diamond drill holes net but closer spaced. This procedure is not the best in mathematical sense for selecting a location. The impact of an additional information to reduce the uncertainty about the parameter been modelled is not the same everywhere within the deposit. Some locations are more sensitive in reducing the local and global uncertainty than others. This study introduces a methodology to select additional sample locations based on stochastic simulation. The procedure takes into account data variability and their spatial location. Multiple equally probable models representing a geological attribute are generated via geostatistical simulation. These models share basically the same histogram and the same variogram obtained from the original dataset. At each block belonging to the model a value is obtained from the n simulations and their combination allows one to access local variability. Variability is measured using an uncertainty index proposed. This index was used to map zones of high variability. A value extracted from a given simulation is added to the original dataset from a zone identified as erratic in the previous maps. The process of adding samples and simulation is repeated and the benefit of the additional sample is evaluated. The contribution of an extra sample was evaluated locally, globally and in terms of variation in total measured resources. The procedure showed to be robust and theoretically sound, mapping zones where the additional information is most beneficial. A case study using coal seam thickness illustrates the method.

Jan 1, 2002

By S. P. Banerjee

By international standards, Indian coal seams are not very gassy. In some of the major coalfields such as Singareni, Wardha, Pench, Chirimiri, Rewa and Talcher Coalfields practically no methane is emitted from the coal seams. Even in the coalfields of Ranigang, Jharia, Bokaro and Karanpura, all of which are situated in the basin of the Damodar river, only a few mines are faced with excessive gas emission problems. But the number of such mines is increasing as deeper reserves are being worked and already the exploitation of some of the best quality coal reserves in the country is held up pending measures for control of methane emission in these mines. Even in mines having no previous history of gas emission, methane has been met near dykes and faults. This was dramatically revealed by an explosion in Dhori colliery in 1965 wherein 268 persons got killed. Until that time, Dhori colliery was considered as a non-gassy mine but on that fateful day gas came to the workings through a freshly exposed fault plane. Similar incidences of ignition of firedamp in so-called non-gassy mines have also occured in the past, for example, in Chapui Khas and Samla Dalurband collieries, but the casualty figures were not as high. After the Dhori explosion, all Indian coal seams have been declared to be gassy, whether presence of methane is detected in the workings or not.

Jan 1, 1980

By J. A. Ryder

Compressed air is a relatively inefficient yet very convenient vehicle for transmitting mechanical energy. It is inefficient when compared to, say, hydraulic or electric energy systems since compressor and pneumatic machine efficiencies are quite low (in the range 20-65%) and reticulation losses can be quite high unless adequate pipe diameters are used to minimize friction drops. It is convenient in that capital and maintenance costs of pipes and machines are exceptionally low, the equipment is flexible and lightweight, the technological level is simple, the form of the energy supply is intrinsic- ally safe, and as an additional minor but psychologically important benefit, it provides a ready source of cooling and air supply for emergency use in deep hot mines. It is for these reasons that compressed air is a premier source of energy for many forms of underground equipment, in particular hand or rig-mounted rockdrills, some forms of rock- handling equipment, and a host of minor applications including agitators, small-lift pumps and temporary f am installations. In a typical S. African deep-level gold or platinum mine, compressed air generation accounts for 15% of the total mine electrical energy bill - more than is used for hoisting. In these mines it is not uncommon for over 100 km of underground compressed air piping to be installed, primarily to supply handheld rockdrills.

Jan 1, 1979

By Alfredo Menendez, Alberto Sarmentero

A B S T R A C T The Los Pijiguaos bauxite is one of the largest accumulations of trihydrate alumina ore recently discovered; it is a plateau type, with no overburden, relatively soft tertiary quartz-bearing bauxite developed on a pre-Cambrian Rapakivi Granite batholith. The deposits are found in the northwestern rim of the Guiana Shield, State of Bolivar, Venezuela, and were discovered in 1976 after a grass-roots exploration campaign. Target areas were mainly selected on the basis of geological and geo¬morpholigcal criteria, guided by correlation with known deposits elsewhere in the Guiana Shield. The vertical. lateritic profile consists of an upper concretionary zone, followed by a mottled zone, a palid zone and finally the weathered rock merging into fresh granite. The upper concretionary zone displays a cellular, pisolitic or spongy texture and contains the following minerals: gibbsite (60-90%),quartz (5-10%), hematite (5-10%), goethite (under 5%), boehmite (traces), kaolinite (traces). The gibbsite content decreases sharply downward from the lower limit of the concretionary zone and the kaolinite and quartz content increases in the underlying mottled zone. The mottled and palid zones display a pseudo rapakivi texture and quartz, kaolinite and mica are the. essential minerals.

Jan 1, 1984

By V. K. Karra

Research by various workers has shown compressive comminution to be significantly more efficient than impact comminution. Based on the work being done at Nordberg, wet compressive crushing in cone crushers producing finer and finer products, shows the feasibility for partial substitution of conventional tumbling mills. For further substitution, major challenges are processing of fine feed slurries in cone crushers to realize a significant size reduction of the particles, and understanding the limitation of the gyratory type units in terms of finest product achievable. The paper addresses the challenges involved, efforts at Nordberg, and the implications to conventional comminution flowsheets.

Jan 1, 1989

By R. J. Sweigard, R. V. Ramani

Estimated costs and revenues can be used in evaluating postmining land use alternatives. However, postmining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact on each alternative under consideration. In this paper, a method is presented that employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1988

By Nasri Munfah, Raymond E. Sandiford

"Superstorm Sandy (Sandy) created a storm surge that inundating many of the tunnels that pass beneath the Hudson and East Rivers. The tunnels are vital infrastructure links for the economy of New York City and the northeast region. The sea water, which contains highly reactive salts, caused significant damage to electrical and mechanical systems. In addition, the salt water inundation left corrosive precipitants on the tunnel linings and on and within electrical duck banks. After the salt water was evacuated from the tunnels, condition assessments were performed using a state of the art approach involving high resolution laser scanning, digital imaging, and thermal imaging. These scans were performed prior to hands on inspections. The damage assessment concluded that, although the tunnel structural linings were not damaged, the interior elements of the tunnels needed major rehabilitation to arrest the continual deterioration of the structures. This paper details the state of the art approach used for these tunnel inspections. INTRODUCTION On October 29, 2012 Super Storm Sandy flooded a large number of both transit and vehicular tunnels in the New York Metropolitan area. The region’s transportation network was severely disrupted. The storm damage is estimated to have been in excess of $30 billion, and with the tunnels out of service, the local economy was losing hundreds of millions in economic activity. Restoration of these tunnels was a very high priority and the resulting expedited restoration process did not always provide adequate time for comprehensive condition surveys. This resulted in many of these surveys being conducted after service restoration. Inspecting highly trafficked transit tunnels is challenging and the logistics of working in short night outages led to a rethinking of the conventional inspection approach. Traditionally, visual and tactile methods are first used to inspect tunnels and then quite often followed by LiDAR (Light Detection and Ranging) scanning and perhaps infra-red scanning. For multi-mile tunnels, the time required to visually map tunnel features can be quite extensive. By performing the scanning first and then performing the visual and tactile inspections, one is able to use the scan data to identify the specific areas that need detailed inspections. This approach was used quite successfully for a number of the NYC tunnels."

Jan 1, 2016

By Andrew J. Neale, Brian C. Flintoff

A review of the current literature, combined with the authors' knowledge of the western Canadian coal industry, indicates that the development and implementation of process control in coal preparation, particularly in flotation applications, is significantly lagging behind that seen in mineral processing. The reasons for this include the lack of inexpensive and reliable sensors, incomplete understanding of the flotation process, limited experience of process control in the coal preparation industry and depressed coal prices, all of which have combined to hinder plant automation. This paper illustrates the benefits of process control in coal flotation, provides a general discussion of the control problem and concludes with two examples drawn from Australian experiences.

Jan 1, 1989

By Dave Willis

In ME'S 1994 Powder River Basin (PRB) coal transportation article, the lead author described some destinations pursued by the railroads. As with many destinations, though, they turned out to be merely stops on the way to places that have yet to be reached. Along the way, the railroads discovered that making it better is a continuous process, not just something done in several phases. This was always known but not at the awareness level that exists in 1998 railroad environments. This update of the 1994 article includes railroad companies' plans for the future of rail transportation in the PRB.

Jan 1, 1998

By F. Djahanguiri

The US Bureau of Mines con¬ducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1997

By [Miroslaw] M. Hajdasinsk

The identification of the real internal rates of return (IRR's) of a project is essential for its economic evaluation. The existing methods for the calculation of IRR's are both cumbersome and unreliable, mainly because of their inability to effectively isolate the real IRR's and incapability of discovering multiple IRR's of even multiplicity. In this paper, a concept of the 'cash flow pattern tree used for isolation of the real IRR's of a project is presented. This concept, combined with the Sturm procedure for counting the real distinct zeros of a polynomial within a specified interval, leads to the development of a method and computer program for isolation and calculation of the real IRR's of a project. The method examines whether or not real IRR's exist, and if they do, isolates them within bounded and narrow intervals in a mathematically founded way. The isolated IRR's, whether simple or multiple, are subsequently calculated either directly or by means of an appropriate approximation procedure. Numerical examples assist the development of the method and the corresponding computer algorithm. Because any Net Present Value treated as a function of interest rate can easily be transformed into a polynomial, the method presented also constitutes a method for finding the real zeros of a polynomial.

Jan 1, 1986

By G. Gaidajis

For the environmentally safe management of the sulphidic waste rock produced from the Stratoni mining facilities, TVX Hellas has examined, within the frame of the funded European research program ROLCOSMOS, the effectiveness of an alternative rehabilitation scheme involving the segregation of the sulphide rich components of waste rock and the engineered application of alkaline additives. The examined waste rock management scheme was evaluated with laboratory test work followed by pilot-scale field applications. In this paper, the results from the two-year monitoring period of the pilot scale application are presented.

Jan 1, 2002

By Kent S. Roessler

The Bureau of Mines is currently investigating the geophysical application of Tomography to monitor leachate during in-situ mining. Determining the location of the leachate is important for both economic and environmental reasons. By analyzing a sequence of tomographic images, we can determine where highly permeable/fractured regions are located and hence, major flow paths. Since BOMTOM (Bureau Of Mines TOMography - Tomographic Reconstruction Program), and BOMCRATR (Bureau Of Mines Curved RAy Tomography - Tomographic Reconstruction Program) are sensitive to user-selected ray path arrival times, we are also investigating the use of neural networks to automate the process of recognizing this feature. This paper presents a technique for detecting fracture zones and their orientations in a region between two boreholes, by using a motion analysis study of a sequence of tomographic images. It also addresses the need for an automated/unbiased method to pick crosshole seismic arrival times using a trained neural network. In exploration geophysics, the picking of first break arrivals represents a pattern recognition task. The neural net paradigm has proved to be a good method of solving this type of task. To pick the first arrival peak of a trace, the network is trained with a set of known (user selected) first arrival peaks by creating a binary image of a set of traces. Once trained, the neural net correctly picked first arrivals of the remaining traces in the set.

Jan 1, 1992

By W. Blake, J. K. Whyatt, B. G. White

In situ stress on the scale of a tunnel or mine may be distorted by geologic structures. The resulting variations in in situ stress have a direct bearing on the potential for mining-induced seismicity. New evidence collected from the Lucky Friday mine by US Bureau of Mines researchers, as well as a review of previous case studies, demonstrated that in situ stress variations affect the [spatial] distribution of mining-induced seismicity. Although overcore stress measurements have been useful in these studies. they are too expensive and, depending, on conditions, may be too difficult to collect. However, information on borehole and raise breakouts: deformation of mine openings: and patterns of seismicity, ground-control problems and rock-burst damage can be used to build a stress database. In conjunction with maps of mine structure and geology and models of rockmass behavior, this database can then be used to build a map of in situ stress variations. Such a map could provide a means of anticipating patterns of mining-induced seismicity and. Thus, could be the basis for planning appropriate measures to ameliorate rock-burst hazards.

Jan 1, 1997

By V. Prabhu, D. Mantha, R. Reddy

Secondary copper blast furnace slag was treated with carbon to derive the conditions for maximum recovery of copper with a minimum simultaneous reduction of iron oxide. Experiments were carried out to study the effect of temperature, carbon and CaO additions to the slag on the efficient recovery of copper. A two-stage reduction process was also employed to study the efficiency of copper recovery and the results were compared with those of single-stage reduction. The maximum recovery of copper in alloy phase was obtained with 5 % initial carbon in the slag, 2% CaO addition to the slag and at a reducing temperature of 1573 K. Higher grade of the alloy phase with respect to copper was obtained by employing a two-stage reduction process. The results obtained in this study are comparable to those of the earlier research on the recovery of copper from reverberatory furnace discard slags.

Jan 1, 2004

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, J. Brent Hiskey, Gürses Öner

Currently there is considerable interest in applying in situ leaching technology to recover copper from oxide ores. In many instances, the distribution of copper mineralization in these deposits is fracture controlled. Laboratory core-leaching experiments have demonstrated that leaching response is sensitive to the dissolution of copper from and the formation of channels along main fractures. Solution short- circuiting can be a major limitation of this technology. This paper describes the application of macromolecular polymers to achieve flow-profile control during leaching. Pre- and post-leached fractures were characterized by computerized tomography (CT) analysis.

Jan 1, 1993