Search Documents

By Chester A. Rowland, David M. Kjos

INTRODUCTION Mineral ore comminution is generally a feed preparation step for subsequent processing stages. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding - primary and secondary), natural or manufactured nonmetallic media (pebble milling) or manufactured metallic media - steel rods, steel or iron balls, or a combination of autogenous media and steel balls (SAG milling). This chapter covers rod and ball mills utilizing manufactured metallic grinding media. MILL DESIGN The interior surface of rod and ball mills exposed to pulp and/or grinding media are protected from wear and corrosion by rubber, metallic or a combination of rubber and metallic wear resistant materials. Rod and ball mills essentially draw constant power, thus are well suited for use of synchronous motors with power factor correction capabilities as drive motors. A net of approximately 120 to 130 percent of running torque is required to cascade the charge in these mills. The pull-in torque is about 130 to 140 percent with the pullout torque to keep the motor in-step (in-phase) generally in excess of 150 percent. When rod and ball mill are started across-the-line the starting and pull-in torques result in inrush currents exceeding 600 percent which possibly result in high voltage drops. To deliver 130 percent starting torque to the mill the motor design must take into account the maximum anticipated voltage drop. Motor torque decreases as the decimal fraction of the voltage available squared. E.g., a motor rated 160% starting torque with a 10% system voltage drop will deliver 160% x or 129.6% torque to its output shaft When it is not possible or practical to start a fully loaded synchronous motor across-the-line it is possible to utilize the motor's pull- out torque to start the mill. By using a clutch, normally an air clutch. between the motor and the mill, the motor is brought up to synchronous speed before the clutch is energized. If the motor has an adequate amount (175 or greater) of pull-out torque the pull-out torque starts the mill without major disruptions on the electrical system. Since the energy release at initial cascade of the mill charge is an inverse function of acceleration time, a minimum acceleration time of 6 to 10 seconds or more is recommended to prevent damage to the mill or the mill foundation. Economics at the time of plant design and mill purchase determine the drive to be used. The simpliest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinionshaft by either an air clutch or flexible coupling. Using a speed reducer between the motor and pinionshaft permits using motors having speeds in the range of 600 to 1000 RPM. In this speed range, if power factor correction is not required induction motors can be used; squirrel cage where there is no restriction on inrush current; slip ring where a slow start and low inrush current is required. Air clutches can also be used to ease starting problems with squirrel cage motors. In some areas of the world induction motors and starters are less expensive than synchronous motors at a sacrifice of motor efficiency and power factor correction. Dual drives, that is two pinions driving one gear mounted on the mill, become economical for ball mills drawing more than 3500 to 4000 horsepower (2600 to 3000 kilowatts). Further developments of the low frequency, low speed synchronous motors with the rotor mounted on the mill shell or an extension of one of the mill trunnions could improve the cost picture for these "gearless drives", making them practical for large ball mills. The percent of critical speed, which is the speed at which the centrifugal force is sufficiently large to cause a small particle to ad- here to the shell liners for the full revolution of the mill is given in mill specifications. Critical speed is determined from the following: Where D is mill diameter inside liners (specified in meters). Cs is critical speed in RPM. When D is specified in feet

Jan 1, 1998

By O. M. G. Newman

The Electrolytic Zinc Company of Australasia Ltd., generates a jarosite waste at its Risdon smelter. Since 1974 this waste has been disposed of at sea off south-east Tasmania. As part of a monitoring programme prescribed by the Australian Government, bottom sediments from the disposal zone are monitored regularly. QEM*SEM image analysis complements conventional chemical analysis, having the ability to partition the occurrence of an element between sediment particles of metallurgical and natural origin. The adaptation of QEM*SEM techniques to the evaluation of bottom sediments provides insight into the fate of the particles of jarosite waste.

Jan 1, 1989

By D. H. Warren

This presentation we hope will provide you with an orderly approach co mine and surface plant closure taken from our experience over the past several years on six different projects within the intermountain states. There is no magic to the approach. It is basic common sense and yet it is interesting how many of the specific details are overlooked due to the individual complexity of each site. Our attempt here is to share some of the issues that have confronted us on these six sites. Please recognize that it is impossible to be all inclusive. Of the six sites we have drawn from; two are mine, mill and smelter sites dating back to pre-1900, one is an industrial site dating back to the early 1900s, two are mill and concentrator sites dating from the late 1940s and one is a mining district site dating from the late 1800s.

Jan 1, 1989

By R. C. Emmett

Gravity sedimentation is one of the most widely used unit operations in mineral processing and hydrometallurgy. Properly selected and operated sedimentation equipment can provide probably the most economical means of concentrating solids or clarifying solutions. Because of the variety of different approaches possible, including the use of modern flocculants, it is easy to overlook the optimum approach in selecting equipment. The different types of sedimentation systems that can be used in the minerals field and the sizing methods that are currently employed will be discussed here. Sedimentation applications usually fall into two areas, clarification or thickening. While the two operations are basically similar, the difference in emphasis (a well-clarified overflow as opposed to a highly concentrated underflow) results in significant differences in testing, equipment design, and operation. Clarifiers may be merely simple settling vessels with no special features, other than ample volume to provide the detention time needed for suspended solids to settle out of the feed slurry. Or, they can be designed to employ elaborate solids-contact techniques utilizing coagulants or flocculants to achieve more rapid clarification through the growth of particle agglomerates. Thickeners also are available in a wide variety of designs, with the main differences concentrated in the design of the raking mechanism. Thickeners operating in series (continuous countercurrent decantation or CCD) are used to recover valuable solution or purify the insoluble solids. Tray thickeners are used for recovering fine particulate solids such as alumina seed, but in other applications have been supplanted largely by unit thickeners or inclined plate units. Thickeners and clarifiers sometimes are used for storage of either solids or overflow liquor, or employed as precipitating reactors, such as in desilication applications. The use of flocculants and coagulants is much more common in modern processing plants, primarily due to the reduction in capital costs rendered possible through the use of these reagents. The terms flocculant and coagulant are often used interchangeably; generally, it is understood that flocculants refer to organic, high molecular weight synthetic or natural polymers which are useful in flocculating most suspended solids, but generally are ineffective on colloidal suspensions. Coagulants refer to chemicals such as those commonly used in water treatment, alum, ferric salts, lime, etc., which are usually far more effective on colloidal solids but cannot achieve the degree of agglomeration that is possible with the polymers. In some cases, both coagulants and flocculants are used in order to achieve optimum results.

Jan 1, 1986

By E. Wiewiorowski

A new technology for recovery of metals from spent catalysts containing aluminum, cobalt, molybdenum, nickel and vanadium was developed. The catalysts are decomposed in two consecutive pressure leaching steps. Sodium aluminate-sodium hydroxide systems are lixiviants in both leaching steps. Selective extraction of molybdenum and vanadium is achieved in the first leaching step. The leach liquor is processed for separation and recovery of these two metals. The residue from the first leaching step is further processed in a second leaching step where alumina is solubilized. The residue from this operation is a nickel-cobalt concentrate. Alumina is separated from the second stage leach liquor by precipitation; the depleted liquor, a sodium aluminate solution, is recycled to the first and second leaching step. This technology has advantages over other approaches for the recovery of metals from spent catalysts because no solid waste is generated.

Jan 1, 1988

By C. J. Pritchard

As productivity improvements reduced the number of continuous miner sections from seven to three while maintaining full productive capacity, a decision was made to test an advancing tailgate ventilation system on the shortwall mining section. Having the shortwall mine its own return air system has freed the third mining section for more productive, less costly mining. The advancing tailgate has provided effective ventilation across the face and gob with acceptable pressure losses. The tailgate development continuous miner section has been since transformed from a low productivity part-time function to a high productivity development/retreat panel and is available for long term mine development duties also.

Jan 1, 1989

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their coal. Sulfur was the major concern, with BTU and sodium limiting the market for some. The Clean Air Act has extended the PRB market into plants converting from other coals. These new customers are more sensitive to constituents affecting boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to control cost more stringently than ever. Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998

By R. C. Keaney

The metals industry is in complete chaos with mines being shut down, profits becoming non-existent, and continual losses to imports from other countries. Yet the raw material supplier to the glass industry has many opportunities to grow and to produce profits. Fortunately, the cost of most glass raw materials are low enough that competition from imports is not anywhere as critical as it is in the metal industries, such as copper, aluminum, lead, and others. But the glass raw material supplier must develop new products, both chemically and physically, to effectively compete in the future. The purpose of this paper is to point out generally where these opportunities exist and to suggest how they may be further developed. As the glass industry looks for energy saving materials, they look once again towards finer materials. A glass furnace is now approximately 40% efficient. Glass engineers are constantly striving for energy savings and it is well known that finer materials melt easier so that the manufacturer can operate his furnace either at lower temperatures for the same production or he can produce more material at the same temperature. The old 20 mesh sand specification is no longer sacred and as the mesh size for sand changes so do the specifications for all other raw materials used in the melting process. Highly instrumented glass furnaces can now measure quite accurately the energy needs to produce glass and can also measure the energy loss in each furnace. Glass technologists desire today a sand with a top size of 40 mesh while some would like to have the top at 60 mesh. This becomes more difficult to accomplish as a raw material supplier without .grinding. As you well know, grinding develops fines. Yet the same technologists will tell us that we can have nothing passing a 140 mesh screen. Therefore, we must develop processes which allows us to produce a finer screen size without increasing the amount of fines passing through the 140 mesh screen. To counteract this, different and changing industries are now demanding much finer products so possibly there will be markets for the fines which are currently separated out of the products. Methods that are practical and low cost must be found to develop different products with different screen specifications. What works for sand can be carried over to the other raw materials used in melting. Among the answers to finer products, of course, are pellets. Aglomeration or pelletizing has been looked at in the past and will be looked at in the future. Considerable work has been done in the glass container industry on this and must be carried out more extensively. By using aglomerated material or pellets, the glass producer will gain the benefits of melting fine materials without suffering from handling or dust problems. Pelletizing, particularly where using basic glass melting materials such as burned lime or sodium silicate, will not only produce a good pellets but will add desirable minerals to the glass batch.

Jan 1, 1986

By A. D. S. Gillies, A. Haghighat

"A study has been undertaken at the Missouri University of Science and Technology (MS&T) limestone Experimental Mine to determine new fans set up and wiring options.to install additional mine ventilation capacity. Selection for main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Available fans for ventilating the mine are Joy and Alphair axial fans each of 24 kW each and two Spendrup booster fans of 12 kW each. The installation of main mine fans on the surface and underground entails numerous considerations. Design of a ventilation network for the Experimental Mine incorporating surface and booster fans has been accomplished using Ventsim Visual program software. The ventilation network has been separated into two segregated parts. A main surface fan and a booster fan have been used in each segregated part of the network. The mine has had a vane axial Joy fan in place for many years. The Alphair 4800 VAX 1800 full blade adjustable pitch vane axial fan was selected and installed as the other surface fan and eventual replacement for the Joy fan. Main surface fans have been connected individually to booster fans in series. The Alphair main surface fan has been installed vertically. Four different wiring options and related cost estimations for addition of the new main fans to the ventilation network have been considered. The analysis resulted in an innovative steel frame design used to allow the fans, when necessary, to be moved to the side of the shaft so that blast pressures do not damage the blades. INTRODUCTION Main fans are the heart of a mine’s ventilation network and play a key role in supplying required airflow (Haghighat, 2014). The Missouri S&T Experimental Mine has been developed in uniform limestone with few stratigraphic features. The mine floor is approximately horizontal and water drains well. A study has been carried out on MS&T Experimental Mine. Selection of main fans has been undertaken according to the mine’s required performance specifications and fan characteristics. Ventsim Visual computer simulation has been used to assist in design of the ventilation network. Wiring circuits, fan foundations and flexibility have been considered as the three main parameters for surface fan installation at the Experimental Mine. Two surface and two underground wiring options and three surface set up options and related cost estimates for the new surface fan system were investigated. Frequent use of explosives in the mine occurs throughout each year. Flexibility in changing the position of a surface fan is important. A number of options have been considered for the location of a vertical main fan positioned on the upcasting shaft. The mine is used for a variety of purposes and flexibility has a high priority amongst design considerations."

Jan 1, 2015

By W. R. Hopkins

Over 95 percent of the world's refined copper is now produced by electrolytic processes. The bulk of this electrolytic copper comes via the conventional route for sulfide ores of concentration, smelting and electro-refining. A rapidly increasing percentage of world production is now achieved using hydrometallurgical routes involving dissolution of the copper values from minerals, purification of the resultant leach solution by solvent extraction and finally deposition as cathodes by electrowinning. The technology can now be considered mature and this paper endeavors to summarize recent developments which, from the authors' perspectives, are important.

Jan 1, 1989

By W. K. Fletcher

As part of an ongoing programme on behaviour of heavy minerals In streams, the dispersion of Au as free gold (Day and Fletcher, 1987), Sn in cassiterite (Fletcher et al, 1987) and W in scheelite (Saxby and Fletcher, 1987) have been investigated downstream of mineralization. The studies of Au and W were undertaken, in British Columbia and the Yukon Territory, respectively, in streams that are strongly influenced by spring snowmelt floods. Sn was investigated under tropical rainforest conditions in Peninnsular Malaysia.

Jan 1, 1988

By Ben E. Lusk

First of all let me say what a genuine pleasure it is to be here. Acapulco certainly is a beautiful change. I'm going to spend sometime talking about change, because frankly I'm astounded at the rate of change in our world today. One good example of this, reminds me that the first time I spoke before the AIME two years ago, we were at the Ramada Inn in Beckley, West Virginia. Today we're at the Princess Hotel in Acapulco, Mexico. Now that's what I call a change. Seriously though, I'm sure you've all heard it said that the most consistent thing about our society is its constant change. Five years ago, no one could have predicted the changes we experienced in the United States during the first half of the 1970's. In the past twenty-four months alone, we have seen two presidents, three vice-presidents and hundreds of administration and government personnel changes. We have stumbled from one social crisis to another, while suffering through rising inflation, major energy shortages and labor unrest that could plunge us into a full scale economic depression. In view of these constant and unpredictable changes around us, it's obvious that we must learn to deal with change and "roll with the punches" if we are to survive. A controversial book published recently, explores in detail the various aspects of change and its impact on man.

Jan 1, 1974

By T. A. Gray

There are several potential large-volume uses for coal ash in mining-related applications that could be environmentally and economically beneficial to mining companies. Actual usage, however, may be constrained by regulations or by perceptions of coal ash and the potential uses. To identify currently allowed uses and to assess constraints to coal ash use in the eastern coal fields, questionnaires were sent to state coal mining agencies to determine their policies on coal ash utilization and to mining companies to solicit their viewpoints on coal ash utilization. Identifying and understanding the constraints will allow for the development of a coordinated and consistent approach to remove or reduce these constraints and possibly allow for increased utilization of coal ash by the mining industry. This paper summarizes the findings of our investigation.

Jan 1, 1995

"On-site research and development as well as in-situ testing are key factors to the successful implementation of new mining equipment and technology. Unfortunately the demands and necessities of research and development often conflict with the reality of mine production in operational mines, especially during early stages of research and development and the initial testing of new equipment. Several experimental mines under university supervision attend to this problem and provide a close-to- reality testing environment for the mining industry and mining equipment manufacturers. This paper gives an overview of the design and organization of such an underground testing area as well as of the wide range of possible operations it can facilitate at the example of the FLB Experimental and Teaching Mine (Forschungs- und Lehrbergwerk) at Technische Universität Bergakademie Freiberg, the central European underground research mine. INTRODUCTION As well as the Mining Engineering education follows the same pattern worldwide, the tasks and duties to be fulfilled by engineers in the productive mines are comparable around the globe. This also holds true for the technologies and equipment needed, both in surface and underground mines. Almost all mining equipment brands are being distributed worldwide. The tasks and challenges of guaranteeing an ever- increasing productivity at the mines, while simultaneously maintaining, respectively improving, safety standards, also in the developing countries and emerging economies, requests a constant development, improvement and adaption both of the engineering education and of R&D in technology and equipment. The increasing safety requirements at the mines, in combination with also increasing safety and liability policies, do often not allow a proper practical education of mining engineering students. At the same time, new technologies and equipment to be deployed / brought to the mines have to be fully functional in a production operation from the very first moment. Time losses like break-down time or even repair and maintenance breaks are often costly and, even when expected up to a certain degree with newly developed machines, have a wider negative impact on the neighboring operations and operations within that mine, thus often being unacceptable within the ongoing production process and extremely costly."

Jan 1, 2015

By E. M. Frizzell

This paper addresses the use of the microcomputer programs BACKONE and BACKWEDG for an estimation of rock mass strength characteristics by back analysis of plane and wedge failures. The artificial support requirements are also determined by the programs PLANE2, BOLTPAT, and BOLTWEDG in terms of rock anchor installation angles, tensions, and installation patterns. These programs have been combined into a package called BACKPACK, which can be applied in open pit mines where some failures have already occurred.

Jan 1, 1988

By G. J. Schneider

The higher stress zone adjacent to an underground opening causes a velocity anomaly that can be mapped in favorable conditions with an acoustic cross-borehole logging system. Bureau personnel used a specialized system at the Colorado School of Mines test site near Idaho Springs, Colorado, to locate the Edgar Mine tunnel and its associated stress anomaly. Data from the logging system' were processed with a tomographic image reconstruction algorithm to map the opening and the location of the high velocity zone around the opening. The velocity imagery from tomographic analysis compared favorably with predictions from numerical modelling of the location of the stress anomaly.

Jan 1, 1988

By S. Polegeg

The basic principle of this separation method was already defined in the middle of the nineteenth century. However, a change over for the treatment of minerals has followed from the construction of proper machines i.e. airjigs and airtables as late as in the twenties and thirties of this century. The main application of this technology was subsequently found in coal processing and reached quite a great dimension in the two following decades. The number of applications of this method in mineral dressing plants decreased rapidly and has almost vanished in the fifties in favour of wet concentration procedures. It has been for a long period as long as up to the eighties that no more consideration was taken for applying dry gravity separation in the field of mineral processing also due to the successful introduction of flotation. Due to the fact that labour cost was increasing remarkably within the past period after the end of World War II also the economic conditions in the agricultural sector became more though. As a result there came up a great demand for harvesting machines. Since agricultural products can only be processed by dry methods in a prevailing number, highly developed machines were introduced for the dry processing of food and feed stuff.

Jan 1, 1992

By D. L. Johnson

A number of small but rich copper sulfide (chalcocite) ore deposits are located on Michigan's Keweenaw Peninsula. These deposits are considered too small to warrant the capital investment required for conventional mining. However, they are being considered for in-situ solution mining as a way to revitalize the area's once prosperous copper extraction industry. Geology, mineralogy and geohydrology of the deposits have been investigated to determine their suitability for leaching; Three conclusions were drawn from the work. First, the sulfide mineralization is found primarily in fractures (65%) and, therefore, is accessible to injected leach solutions. Second, the ores are shallow, occurring from surface exposure to about 200 meters depth; injection and recovery wells would not have to be excessively deep. Third, the rock was found to have low permeability, in the neighborhood of thirty millidarcys or less. However, preliminary hydraulic fracturing experiments indicate that this will be an effective method for permeability enhancement. In one experiment a permeability increase of 100 times was achieved using a very low injection pressure at shallow depth. Additionally, fracture aperture spacings measured from drill core were correlated with fair success to field permeabilities.

Jan 1, 1989

By G. E. Wasson

Coal in most refuse ponds including those owned by Consolidation Coal Company can be recovered by froth flotation techniques. Laboratory studies show that the flotation conditions required for coal recovery varied greatly from pond to pond. The variables found to be most important for high coal recovery and low product ash were: a) the amount and type of flotation reagents and b) the degree of conditioning before flotation. Coal recovery at a rate of 0.504 kg/s (2 tons/hr) was demonstrated at a pond site employing a mobile froth flotation unit.

Jan 1, 1988

By S. D. Thompson

Conveyor belt haulage has become the preferred mainline transport method in under-ground coal mining, especially for multi-unit mines. Optimum designs for belts (width and speed) and surge bins (placement, capacity, and discharge rate) are necessary for minimizing haulage cost. Two computer simulation models, CMaCS and BELTSIM, available for optimizing these designs are compared. These comparison include: modeling, input data requirements, statistical flexibility, accuracy of simulated loading, and execution time.

Jan 1, 1989