Search Documents

By S. Zaman, John Bulter, M. E. Defoe, Franklin T. Davis

This section deals with the carbon minerals and materials: graphite, tar sands, gilsonite, and diamond. as well as sulfur and the sulfides of mercury, arsenic, antimony, and bismuth. Table I contains the production figures for each of these commodities in the United States and in the world. Specifications for concentrates are also summarized as are prices for concentrates at the time the section was written. In each chapter an attempt has teen made to describe the more common commercial mineral involved with the commodity, the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985

By Werner Stahl, Karsten Keller

Vibration screens are commonly used not only in classifying bulk material but also in dewatering it. The lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. Firstly, the dewatering of bulk material will be shown, based on a physical model. Because of the oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. The comparison between dewatering theory and practice will be shown by measurements using coal, limestone, etc. Dewatering measurements, which have been conducted on a vibration screen, demonstrate that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibilities of improving vibration dewatering will be described.

Jan 1, 1995

By John A. Ames

Limestone for portland cement must be beneficiated to produce uniform raw material for the kiln. Careful quarrying and selective recovery are factors in this process, but the chief aspects of beneficiation are "in plant" processes, such as crushing and screening, washing, grinding, flotation, and heavy-media separation. Numerous technical and economic problems exist. Detailed studies of the limestone deposit and the stone itself are required for intelligent beneficiation. As used in this paper, beneficiation is defined as the improving of limestone composition so as to produce an economically usable raw material A limestone deposit is defined as a mass of limestone which can be recovered, by quarrying or mining, for sale or for use in a commercially profitable operation. The stone may require elaborate processing, or it may qualify with little or none. Obviously, the "commercially profitable" qualification may change as the economy changes. Potentially commercial deposits may be of much better quality than actually developed deposits, and yet may be denied development for various economic reasons.

Jan 1, 1966

By R. Gong, R. Bhaskar

A coal mine study was conducted to evaluate the effectiveness of a compressed-air, foam spray system installed under a continuous miner boom and directed to cover the pan and the gathering arm. The study's objectives were to evaluate the foam, underboom sprays' effect on: • the respirable dust concentration in the ambient air, and • the quartz concentration in the airborne, respirable dust. The foam generation and delivery system's engineering design is described in the paper, followed by descriptions of the mine and the dust sampling strategy. The data were analyzed to study the foam's effects on respirable dust and quartz concentrations at the continuous miner cab, the face return and the intake. The data indicate reductions in the dust's quartz content, ranging from 19.7% to 64.6%, in eight of 11 comparisons of the foam vs. no foam cuts. In addition, airborne intake dust reductions were observed in eight of 11 comparisons.

Jan 1, 1993

By V. Srajer

Operations research includes the application of systems analysis to mining operations, the acquisition of field data and the creation and verification of computer models of these operations. These activities result in the generation of computerized mine planning tools which have a firm base-in observational facts. The Surface Mining Laboratory of the Canada Centre for Mineral and Energy Technology (CANMET), in Devon, Alberta has been engaged in operations research activities since 1982. The work includes computer simulation of truck/shovel, continuous mining equipment and dragline operations. Other examples include cooperative programs with industry (such as the demonstration and evaluation of an integrated truck management system), the development of a device to measure off-highway truck rolling resistance, and an automated remote data transmission network. The presentation outlines existing and proposed research projects of the Operations Research group.

Jan 1, 1989

By Henry P. Ehrlinger III, Latif Khan, John M. Lytle

The primary purpose of this project was to produce and test coal concentrates made from coal preparation plant waste fines for use in a slurry-fed gasifier. Concentrates from several individual waste streams were examined to determine their amenability as feedstock for a slurry-fed, slagging, entrained-flow gasifier. The tests included analyses of the plant feed and product, material balances, and estimates of gasification reactivity and of pumpability. The following preparation plant fines were examined: • fresh rejects produced in a plant processing underground- mined Springfield Coal • fresh rejects produced in a plant processing underground- mined Herrin Coal • fresh rejects produced in a plant processing surface-mined Springfield Coal and Herrin Coal • Five-year old impounded fines rejected during processing of underground mined Herrin Coal. At high coal recoveries the Btu content of the concentrates was greater than the Btu content of the utility product from the plant. The coal recovered from fines was found to be entirely acceptable for gasification and pumping without additives.

Jan 1, 1995

By J. M. Baker

It seems appropriate here to open with a quotation from the great pre-Confucian philosopher Lao-tze: "The softest thing in the world dashes against and overcomes the hardest. There is nothing in the world softer or weaker than water, and yet for attacking things that are firm and strong there is nothing that can take precedence of it." I am happy to report that our system of mining has worked out, with minor modifications, as well or better than was predicted. This, in a period of rising labor and material costs, has been most gratifying. Gilsonite is a solid hydrocarbon which occurs in vertical fissures cutting the sandstone and shale beds of the Uintah formation in south¬eastern Utah. It is found in other parts of the world under similar occurrence but nowhere else is it now being mined commercially. The Gilsonite veins on entering the shale members of the Green¬river formation break into small veinlets separated by shale, These veinlets are not now economical to mine.

Jan 1, 1959

By Ralph D. Daley, Kevin E. Redinger

The production of coal/water fuel (CWF), a highly loaded mixture of finely ground coal, water, and chemical additives, presents a unique opportunity for significant ash and sulfur reduction through physical coal cleaning. Froth flotation can be integrated with the staged, wet, fine grinding inherent in the CWF production process. A laboratory scale research program was conducted to demonstrate the feasibility of a flexible, integrated coal cleaning/CWF process flowsheet. Performance of the conceptual flowsheet was examined for two coals of CWF commercial interest, Upper Freeport and Pittsburgh seam coals, from central and southwestern Pennsylvania, respectively. Several multi-stage coal flotation and reverse flotation circuits were evaluated. CWF was produced from the cleaned coal in each case at similar solids loadings and viscosities as observed for the raw coal. However, the ash loading and SO2 emission potential for each CWF had been significantly reduced.

Jan 1, 1988

By Jorgen Elbrond

Before and in the early stages of industrialization, mining was the undisputed leader in technology. It represented the high-tech of the time. Early mechanization bears witness to that. Hoisting and rock breaking driven by waterpower are such examples. The mines' use of the steam engine was a major incentive to its development. By these means new mines could be opened and more metal supplied. Understanding of systems was essential for miners when shaping the infrastructure of the mines for the transportation of ore, material and men and for the evacuation of water and for ventilation. The irrigation systems of ancient mines are such examples. However, with the industrial revolution other more specialized branches of industry advanced further, and the mines became users of other industrial branches technologies. The mining industry had, however, always been quick to recognize a good thing and use it, when time was right. But, compared with other branches of industry, the mining industry has the disadvantage of working in a rugged environment with (and actually inside) a raw material which is abrasive and highly variable with respect to mechanical properties. This determines the rather high unpredictability of mining machines' performances and their low availabilities and explains a part of the delays in introducing technological advances.

Jan 1, 1989

By Li. S. D., R. X. Zhang, K. M. Li, Y. D. Zhang, Y. J. Hou, S. G. Li

A computer aided design software system for long range coal surface mine planning has been developed by the authors. The system is composed of two subsystems: a coal deposite sub- system and a long range mine planning system. The geological parameters are estimated and a grid model is formed, then a 3-D block model can be developed for mining design. The long range surface mine planning system is based on oriented graph simulation and combined approaches to seek for the optimal deign alternative. This mining model consists of a number of sub-models to realize mining design functions such as: calculation of mining volume and coal quality by graph scanning; determination of operational stripping ratio by interactive design; varification of annual coal production; delimitation and development of dumping site; optimization of material flow direction and volumes by Linear Programming; surface mine production scheduling by interactive iteration; etc. The software package was developed on PC computer 486. It features classified menu guide, module structure, figure and graph representation on the screen and flexible interactive functions. This system has been applied to an open cut coal mine and predicted functions have been obtained.

Jan 1, 1996

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy

Chromitiferous overburden containing nickel in oxide form is reduced with CO-CO2-N2 gas mixtures. This converts the nickel oxide to metallic nickel and restricts the iron oxide to the magnetite state to extract the nickel. Reduction experiments were carried out on 500-g samples in a bench-scale vertical reactor. The tests were run to establish the process parameters, including the optimum partial pressure of CO, the reducing gas flow rate, granule size and roasting time. The reduced calcine is then subjected to an ammonia-ammoniacal carbonate leach to extract nickel selectively as its amine complex. More than 90% of the nickel could be extracted with a volumetric CO/(CO+CO2) ratio of 0.57 at 750°C and a roasting time of 90 min. The addition of 2.5% (by weight) charcoal to the granules improved nickel extraction by 11 % to 19%. Nickel leaching efficiency with ammoniacal solution is compared to the bromine-methanol method.

Jan 1, 2000

By D. B. Dreisinger, H. J. Sohn, J. S. Sohn, G. A. Kordosky

The transport of lithium through a supported liquid membrane was studied with a mixture of D2EHPA and TBP in kerosene as a mobile carrier. In the flat- sheet supported liquid membrane(SLM) system, experiments were carried out to investigate the effects of concentration of mobile carriers in the membrane solution, hydrogen ion in the feed solution, and temperature on the transport of lithium. Experimental results agreed well with a transport model for permeating lithium across the liquid membrane. The permeation rates of lithium can be explained in terms of diffusion of a Li-complex through the membrane phase. For a practical application of an SLM method, a hollow fiber module has been used and lithium can be concentrated more than three times in 24 hours.

Jan 1, 1993

By L. E. Baker, M. J. Leck

OSIRIS is a continuous monitoring system for respirable dust which has been specifically designed for mining and related industries. By using the latest microprocessor technology, OSIRIS provides a sophisticated dust measuring system which is a cost effective alternative to regular gravimetric sampling. The system is certified intrinsically safe for use underground. Up to eight underground OSIRIS sensors can be controlled and monitored by a single IBM PC computer located at the mine surface. This computer provides continuous and instantaneous information about the dust concentrations at the sites being monitored. Information is available in tabular and graphical form. The paper gives details of proving trials of the OSIRIS system in some UK coal mines. During these trials, adjacent OSIRIS sensors placed on the same underground roadway cross-section gave virtually identical results. Throughout a good correlation was obtained with conventional gravimetric dust samples. The OSIRIS equipment proved both reliable and easy to operate. OSIRIS was designed and developed by the Safety Engineering Laboratory of the UK Health and Safety Executive. It is now available commercially and is being

Jan 1, 1987

By K. H. Al-Rawahy

Appreciation and awareness of the unique nature of mineral investment and ultimate development of a mine are crucial in promoting sustainable development. Special characteristics of mineral development include high capital intensive, long pre-production period, high risk, and the unavoidable ?economic? depletion. This paper examines ways to integrate these unique attributes of the mineral industry into the educational process, so that a properly advised and knowledgeable culture in terms of a sustainable mineral industry can be developed. Specific approaches are investigated in order to achieve this objective. These include a stochastic evaluation of a mineral investment proposal, adding a premium to the cost of capital that is used for valuation process, and internalizing incidental costs to the private cost function, thereby realizing the true (vs. apparent) marginal social cost of the proposed development. Undoubtedly, a total evaluation of any mineral project that accounts for both tangible and intangible parameters will contribute to sustainable development objectives. By incorporating the practical application of apparent theoretical topics such as risk, probability, and externality, and their relevance and impact on mineral lifecycle (prospecting, exploration, development, exploitation, use, and ultimate disposal) into the educational process, it is hoped that a generation of technocrats and decision makers that are familiar with and concerned about sustainable development will emerge.

Jan 1, 2007

By T. H. Combs, G. T. Lineberry

Increased productivity in the US underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on shuttle car sections results in more uniform loading and reduces spillage vulnerability. An investigation was made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is modeled, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods for predicting the loss in face production from lower feeder discharge rates were investigated.

Jan 1, 1995

By Malcolm J. McPherson, Satya Harpalani

A thorough knowledge of coal permeability and its variation with factors like stress conditions, and time, is useful in simulation studies of mine ventilation and coalbed methane recovery, as well as characterizing coalbed methane reservoirs. An experimental investigation was carried out to study the gas flow characteristics of coal to enhance the under- standing of the mechanism of methane flow through it. The work consisted of measurement of permeability of coal samples under triaxial stress and an examination of the physical structure of coal using electron microscopy. Effort was made to fit the experimental data to several phenomenological models that have been used to describe fluid flow through porous media. It was realized that gas flow through coal cannot be described by models that assume this flow to be through a bundle of capillary tubes. However, results suggest that this gas flow could be predominantly through fractures and cracks in coal, and this could be represented by flow between parallel plates.

Jan 1, 1986

By K. Hanumantha Rao, K. S. E. Forssberg

The separation of feldspars from quartz has been the subject of numerous studies since 1930 and the flotation process so far proved to be the most suitable method. In the conventional process, feldspars are separated from quartz using a cationic collector and hydrofluoric acid as an activator of feldspars. There is no general agreement on the mechanism of fluoride activation of feldspar surfaces and the role of fluoride ions is briefly discussed. The use of HF is no longer acceptable due to environmental and health problems, and a few new reagents schemes have been reported. The available evidence shows that the success of these new reagent schemes is very limited. A new reagent scheme which is environmentally safe and cost effective for the separation of feldspars from quartz is yet to be resolved.

Jan 1, 1994

By P. Venkatraman, F. S. Knoll, W. S. Kow

Froth flotation is the most widely used technique for cleaning fine coal. This practice may change, however, with the development of enhanced gravity concentrators such as the Mozley Multi- Gravity Separator (MGS). The MGS is a flowing-film concentrator that utilizes centrifugal forces to improve the separation of flotation-size particles. In the present work, a pilot-scale test program was conducted to examine the effects of feed rate, feed solids content, wash water flow rate and drum rotation speed on the performance of the MGS. The test results indicate that the MGS effectively rejects high-density minerals such as pyrite, while ultrafine ash-forming minerals are removed less efficiently. A major advantage of the MGS is that high separation efficiencies can be realized without additional grinding, flotation reagents or heavy media. This article describes the working principles of the MGS and presents data obtained from recent pilot-scale test work.

Jan 1, 1995

By J. Drelich, J. Pletka

Lost foam casting is a process in which a polymeric material is formed into the shape of the part to be cast. Parts that are more complex are fabricated by simply gluing several patterns together. The pattern is then coated with a refractory material consisting of a mineral mixture and binders. Finally, hot metal is poured into the pattern, evaporating the expanded polystyrene and taking the shape of the coating shell. Prior to casting, a significant number of the patterns are damaged and inevitably landfilled. In this study, a process was developed for the recovery of expanded polystyrene from the coating and glue contaminants. The process consists of shredding, impact comminution, size classification and pneumatic separation. It is successful in separating up to 97% of the contaminants, while recovering 95% of the polystyrene. Key words: Casting, Lost foam process, Expanded polystyrene recovery

Jan 1, 2003

By R. Sivamohan, F. Huang

A mineral processing strategy developed for the finely and complexly interlayered calcite rich wollastonite, microcline, and iron-garnet ore of Jokkmokk, northern Sweden, gives an overall calcite recovery of 89.4% at a grade of 90.7% CaCO3. The wollastonite product assays 53.0% Ca- SiO3 at a recovery of 92.2%. The significant elements of the developed strategy are stepwise grinding, wet high intensity magnetic separation (WHIMS), reverse flotation and starvation flotation. Stepwise grinding avoids the overgrinding of soft calcite. WHIMS removes the colored iron-garnet impurity and thereby increases the whiteness of the product. Reverse flotation enables a simple flotation circuit and starvation `flotation helps to optimize the physicochemical conditions in cleaner flotation by giving rougher products of narrow particle size distributions. Moreover, with the reagent scheme developed in this work only one cleaner stage is necessary for the various rougher flotation products to be upgraded to give the foregoing results. In this paper, the strategy is presented in detail along with appropriate results.

Jan 1, 1990