Search Documents

By Giorgio Höfer-Öllinger, Peter Pointner, Manfred Stadlober

"SUMMARY Investigations from tunnel face are part of risk mitigation measures during the excavation works. With the tunnel equipment, percussion drillings of up to 30-40m can be achieved. Core drillings are state of art method for investigation exceeding 50m. At Koralm base tunnel, up to 270m deep percussion drillings were performed with drilling rigs and accompanied by an intensive investigation program. These investigations consisted of monitoring during the drilling, field tests (with packer, using the preventer, borehole imaging) and in laboratory. Percussion drillings are cheaper and save time of interruption of the excavation progress. INTRODUCTION As part of a proper risk management, horizontal advance drillings during excavation of underground works can be seen as state of art and meet wide acceptance. Core drillings, deep and shallow percussion drillings can be differed. The selection of the type of drilling, meanwhile, causes intensive discussions. On the one hand, only a core drilling allows a direct investigation of the rock mass expected during later excavation works. On the other hand core drillings are expensive in both cost and time – if there is no excavation progress during the investigation measures – in construction time. Percussion drillings can be performed as rapid investigation measure with the excavation equipment (“Jumbo”) allowing two dimensional image of the ground around the cross section. There is some limitation concerning a reasonable depth of approximately 30m and a borehole diameter of 76mm. The applications of preventer, packer or borehole imaging are hardly applicable. By use of a drilling rig depths of percussion drillings of several hundred meters can be achieved relative easily and there is less limitation of the borehole diameter. Installation of a preventer is possible, as well as packer tests and borehole measurements (imaging, gyroscope, borehole geophysics). The gap of information between core and percussion drilling cannot be closed completely, but it can be reduced substantially and sufficiently by combination of an intensive program of measurements and analysis accompanying the investigation works."

Jan 1, 2016

By A. MacG. Robertson

INTRODUCTION The tailings, or solid waste, remaining after uranium has been extracted from an ore and the liquid wastes associated with it contain both radioactive and other substances which, if released to the environment, may have a detrimental impact on man and his environment. Although the radioactivity of the waste is of natural origin, the mining and milling process results in bringing the radioactive ore to the surface, changing its chemical and physical form, increasing its mobility and, therefore, enhancing the potential radiological exposure to man. Exposure to radionuclides released from a tailings impoundment, while small as applied to any one generation, can be made large by counting far into the future, large enough to be the dominant source of exposure from the nuclear fuel cycle, Cunningham (1978). Increasingly it is being found that where the prime concern was initially the radionuclide releases, the release of other pollutants and contaminants may be of equal or greater concern. While there is a definite benefit, at least to present generations, resulting from the recovery of uranium, current and long-term concerns require that consequential present and future releases be kept as low as is reasonably achievable. Design practice, to minimize this release, is currently passing through a technical revolution; precipitated by public and institutional concerns. New techniques and methods are, therefore, being actively sought and continuously implemented. Because of the complexity of the pollutant release mechanisms and the sitespecific nature of each impoundment site and tailings product, a wide variety of site selection and design options have been implemented or considered. It is often possible to design a number of satisfactory tailings disposal schemes which differ widely in nature and cost. This paper outlines the principal areas in which options are available and discusses some of these options. Both operating and post-decommissioning conditions are consi-

Jan 1, 1980

By P. R. Bailey

The use of carbon for the recovery of the gold dissolved in cyanide leaching began with a pilot unit at Barberton in 1977. This was quickly followed by larger scale plants at Modderfontein (1978), President Brand (calcine 1980), Western Areas (filter tails 1980) and Beisa (primary ore 1981) and has grown to become the preferred process. There are currently 34 operations that use the carbon in pulp/leach process which accounts for 35 percent of South Africa's gold production. The size of individual plant varies over a wide range.

Jan 1, 1993

By C. Pomeroy, J. Weyer, J. Brune

"Mining began in the Erzgebirge (“ore mountains”) region of Saxony, Germany more than 800 years ago, and extensive underground workings cut through the entire area. Some of these old workings are still used today: not for production, but for offering an underground venue for research, tourism and university teaching. One example is the Reiche Zeche mine at the Technische Universität Bergakadamie Freiberg which hosts one of the oldest mining engineering programs in the world. It is imperative to keep all active mine workings well ventilated to make the mine safe for students, visitors and researchers. Since the mine workings at Reiche Zeche are so vast, extensive and, to a large extent unexplored and unmapped, it has been difficult to provide a complete, functioning and adequate mine ventilation model for this mine that accounts for all known and unknown leakage air flows. Researchers at the Colorado School of Mines have cooperation with their colleagues at Freiberg to establish a mine ventilation network model based on a limited number of air readings in known and accessible drifts. In order to balance the measured air quantities, leakage flows were quantified and mapped by comparing input and output flows of mapped drifts, and modelled using Ventsim Visual, a powerful visualization software package. The resulting mine ventilation model is used to locate and quantify the leakage air flows and to examine how much air is lost in each area. With this model, ventilation changes and improvements underground can be documented reflected in the model. This enables the Bergakadamie Freiberg to project air changes required for scientific experiments and to set up mine ventilation in specific areas and for specific needs. The model also enables better ventilation control and monitoring than before. Finally, the model can be used to predict ventilation changes and escape way contamination in case of a fire, ground fall or inundation in the mine. The latter becomes important as the lower mine workings are often flooded during spring runoff, which has created uncertainty about mine ventilation in the past. HISTORICAL BACKGROUND The discovery of silver, lead, zinc, tin and other valuable metal ores in the Erzgebirge region of Saxony, Germany began in the12th century and started a mining boom than lasted for centuries. Surface mines quickly developed underground to access the higher grade veins. Explored by the early geologists and driven by the ingenuity of the miners, the underground works expanded vastly throughout Freiberg and the surrounding region. Development followed the highest grade veins, and engineers developed solutions to drain water and provide limited ventilation to the underground workings. Still, engineered and planned ventilation was usually not a priority in the development of a new drift, which today makes ventilation modeling a significant challenge."

Jan 1, 2015

By Wayne J. Nordstrom, Dennis L. Murr, James E. Wennen

National Steel Pellet Company (NSPC) conducted pilot scale testing and computer simulation studies which indicates that the capacity of the secondary grinding mill could be increased and that concentrate grade improvement could be expected with improved classification in the grinding circuit. Based on these studies, a decision was made to modify one secondary ball mill line at NSPC to include both cyclone and screen classification with magnetic separation applied to the circulating load. This paper will briefly discuss the studies leading to the decision to modify the circuit, the design of the modified circuit and the initial start-up and operating experience.

Jan 1, 1997

By D. M. Conner

An innovative patented process has been developed to convert high volume wastes--fly ash from coal-fired power plants, municipal solid waste (MSW) ash from incineration, solids from waste water treatment and paper mill sludge into a high value and environmentally benign product in the form of a lightweight aggregate. Lightweight Aggregate is widely used in the building construction industry in the United States, Europe and some Asian countries. This paper will present the development of the process, the process itself and details on the first commercial scale plant. The commercial plant is owned and operated by Wisconsin Electric Power (WEPCO).

Jan 1, 1997

By G. B. Michaels

Exploration programs for mineral resources often involve analysis of soils or stream sediments for the mineral being sought or its pathfinders. Because many metals are toxic to microorganisms, patterns of metal resistance in soil or aquatic populations may provide additional useful information at a reasonable coat. These patterns in some cases have been more effective than the soil geo-chemistry and may be easier to obtain. Elevated levels of resistance to silver and its path-finders have been demonstrated in stream populations from an area of known silver deposits, and resistance to gold pathfinders has been demonstrated for gold-bearing areas. Uranium has also been located by this method.

Jan 1, 1989

By S. K. Kawatra

Although temperature is known to have a substantial effect on many processes, this parameter has been widely dismissed as insignificant for mineral comminution. For this reason, temperature effects on grinding have largely escaped notice. However, it has been observed that processing plants which are subjected to large seasonal temperature variations show a change in performance which appears to be due to changing feed temperatures. The general effect is an increase of the specific energy consumption as the temperature decreases. In autogenous mills, an increased rate of production of critical-size material has also been observed. This is due, at least in part, to changing rheological conditions in the mill, with the slurry viscosity increasing markedly at low temperatures. Mechanical changes in the rock with temperature, such as increased brittle fracture, is also responsible for a portion of the observed seasonal effect, and may account for this phenomenon being observed only in certain plants.

Jan 1, 1989

By Shawn Boltz, Erik Westman, Derrick Chambers, Xingdong Zhaoa, Qiankun Zhua

Microseismic passive velocity tomography is becoming an effective technology for large-scale mining-induced stress monitoring in underground mines, especially in the field of early warning of mining-induced hazards. Aiming at the problems of missing low-magnitude events in traditional microseismic monitoring, as well as the potential to increase the resolution of the tomograms in both time and space, a microseismic passive velocity tomography analysis method based on the template matching method was proposed. First, the template matching method was used to pick microseismic events. Then, the probabilistic, non-linear, global-search earthquake location method was used to locate the events and calculate travel time and travel distance. Finally, the fast-marching method was used to carry out passive velocity tomography analysis to image the movement of the abutment stress associated with the longwall. The results show that the selected templates can identify more microseismic events than the traditional microseismic analysis, and the variation trend of events in each day is consistent with the data from the traditional analysis. Using microseismic event locations, travel times and travel distance can effectively complete microseismic passive velocity tomography analysis in each day during the study period and can effectively identify the forward and side abutment stress zones of that longwall panel. This study provides a reference for the identification of mine-induced high stress zones, which has implications for hazard identification and mitigation, with increased resolution of the tomograms in time and space.

Jun 25, 2024

By D. Yeager

Researchers at the U.S. Bureau of Mines have successfully used a genetic algorithm to tune computer models of three column flotation units simulating a separation circuit. The computer models rely on empirical constants that are selected so that the models accurately predict the performance characteristics of individual column flotation units. Unfortunately, these empirical constants have traditionally been selected using a time consuming trial and error process. A new and more efficient approach to selecting empirical constants for computer models has been developed. A genetic algorithm has been used to select the empirical constants for column flotation models used to simulate a three column circuit. Genetic algorithms are search algorithms based on the mechanics of natural genetics. They rapidly locate near optimum solutions in difficult search spaces. Bureau researchers have used these innovative search algorithms to dramatically reduce the time needed to select empirical constants for column flotation models. The approach is applicable to the selection of empirical constants for numerous other computer models.

Jan 1, 1995

By M. Robson

Water & Earth Technologies, Inc. (WET), Habitat Management, Inc. (HMI) and Chevron Mining, Inc. (CMI) together developed a solution for reclaiming steep southwest facing slopes in mining Area 12C that have historically been prone to excessive erosion, low vegetation establishment and continuing maintenance. Area 12C is located in the east wing of the Chevron McKinley Coal Mine, 27 miles northwest of Gallup, New Mexico, on Navajo Nation land administered by the Office of Surface Mining (OSM). Mining in this area was completed in May of 2007. Challenges encountered for this reclamation project included the need to reclaim graded material on a slope of 18-35% with southwest facing aspect, the presence of undisturbed rock outcropping that needed to be avoided during reclamation, the operational need to limit bulldozer pushes and the inability to import or export additional materials for construction. Two different reclamation alternatives were considered for Area 12C. The first alternative would use a traditional reclamation approach including three levels of draining terraces designed to convey water on a 3% slope to a single riprapped down drain. Terracing and down drains have been used to reclaim areas with similar terrain conditions elsewhere at the McKinely Mine and have failed to adequately control erosion (Williamson 2006). Terrace overtopping and down drain blowouts have been issues in maintenance and functionality for the mine. Maintenance routines consist of cleaning out terraces where they have filled in with sediment and repairing damaged or blown out terraces and down drains.

Jan 1, 2010

By V. B. Achanti

This paper deals with the effect of various bit geometric parameters on failure characteristics of rock material. Improvement of rock cutting efficiency of continuous mining machines has been an interesting research topic for the last few decades. In the current study, an automated rotary rock cutting simulator, duplicating a continuous miner, was utilized to study these parameters in the laboratory. Improvement of bit performance in terms of its life, cutting efficiency, dust production and energy consumption has drawn wide spread attention over the years. Research shows that optimizing bit parameters can result in efficient fragmentation of rock. Indiana limestone rock material was utilized in this study while bit tip angle, bit tip size, bit spacing, depth of cut and cutting velocity of rotary drum were varied to investigate the failure characteristics. The cutting pressure, penetrating pressure and the depth of cut were monitored on the simulator during the cutting process. Air borne dust and settled dust were measured for each experiment. Then, the specific airborne dust and specific energy were determined for the each type of bit. Triaxial tests were carried out to correlate the failure angle of the rock in static case to dynamic cutting process failure. The physical and mechanical properties of the rock were also determined in order to assess their influence on the wear characteristics of each bit.

Jan 1, 1998

By T. Gollaher

The use of paste thickeners for mineral tailings has gained increasing acceptance by the mining industry throughout the world and in the U.S. during the last five years. Advantages of water recovery and environmental sustainability are the driving forces for paste as an alternative to conventional thickening and the slurry pond. This paper presents a summary of the differences between paste and conventional tailings thickeners, along with recent examples of full-scale paste thickener installations.

Jan 1, 2010

By R. J. Sterrett

To the average mine operator, the implementation of environmental regulations are viewed as a drain on the profitability of the mine. Since the birth of environmental awareness in the late 1960's, which led to the passage of the National Environmental Policy Act (NEPA) in 1969, and through the publicity brought about by the discovery of Love Canal in 1978, the public are clamoring for increased environmental protection. It should be emphasized that the concern regarding the issues of the handling and disposal of nuclear and toxic wastes is not limited to a few overzealous environmental advocates. Toxic waste issues have "grass roots" interest and support. A reflection of this support has been the passage of key pieces of federal legislation. . Of particular interest are the following acts: Clean Water, Toxic Substances Control, Surface Mine Land Reclamation, the Resource Conservation and Recovery Act (RCRA) and the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). The last act is often referred to as "Superfund". Both RCRA and CERCLA have been re-authorized and amended, and in their re-authorization they have been substantially strengthened. Of the last two pieces of legislation, RCRA is the most powerful in that it governs the handling of hazardous wastes from "birth to grave". CERCLA was established to cleanup abandoned waste sites which are threatening human health or the environment. These cleanups can be undertaken by the government and then billed back to the previous owners or to the disposers at the sites.

Jan 1, 1988

By D. J. Miller

Environmental considerations are extremely important in planning and carrying out mergers, acquisitions and real estate transfers. It is not inconceivable that potential or actual environmental liabilities could exceed the targeted company's net worth or the book value of the real estate of interest. It is therefore essential that an environmental due diligence investigation (DDI) be performed to quantify environmental liabilities before sales, mergers or acquisitions. This paper will discuss general procedures used in environmental due diligence investigations. The emphasis will be placed on mergers and acquisitions. It should be pointed out that the procedures discussed in this paper are general and must be modified to fit each particular merger or acquisition under consideration.

Jan 1, 1988

By Eric W. Johnson

In the late 1950's a low-grade copper ore zone was outlined at the fifty-year-old McIntyre Porcupine Mine in Northern Ontario. Following this an independent copper circuit was installed in the existing gold mill. The nature of the operation decreed that capital expenditure be a minimum. To this end, in order to resolve the problem of storing and grinding two separate ores, it was decided to install a divider in the existing 4000 ton capacity fine ore storage bin and to replace ten conventional feeders with sixteen Mexican feeders. The article describes a successful application of the Mexican type feeder.

Jan 1, 1968

By J. B. Cabezas

The metallurgical processes that are frequently applied today use strong solutions and are of alkaline, acidic, or organic nature. These play a very important part in recovery of values from many ores. These solutions are of such a chemical nature that they are generally corrosive, flammable, and contaminating. In most cases, they are highly dangerous to the environment. Within the extractive metallurgical industry, it is also very common to have to deal with the handling of contaminating solutions with a high content of cyanide, arsenic, mercury, lead, copper kerosene, acid and many other components whose temporary or permanent confinement within the process must be adequate and absolute.

Jan 1, 1986

By P. Henderson, M. E. Morris, W. A. Johnson, F. D’Alessandro, D. Wilton

"The objective of this research is to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models can then be utilised to assist in the design of effective controls. This project will provide a significantly improved level of knowledge and control over current lightning abatement techniques. The findings may also be applied to open cut and coal preparation situations. Computer modelling identified that by isolating cased boreholes from underground conductive media such as roof mesh, and placing spacings between roof mesh the risk of an ignition can be reduced by more than a factor of ten. These controls should be applied in conjunction with minimising the potential for a flammable atmosphere to exist underground and ensuring that there is no transmission medium for the lightning to reach the atmosphere. INTRODUCTION The objective of this research was to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models could then be utilised to assist in the design of effective controls. If successful this project would provide a significantly improved level of knowledge and control over current lightning abatement techniques. The direct potential for harm from lightning has long been recognised for the surface facilities of coal mines. However recent events at Blakefield South in NSW on January 5 2011 (DTI, 2011) and at Sago mine in the USA in 2006 (MSHA, 2007) have suggested that there is potential for lightning to cause significant damage to the underground workings of a coal mine. A very detailed analysis carried out by as part of the MSHA investigation into the SAGO disaster by Sandia Laboratories identified at least ten other incidents over the past thirteen years where lightning had probably caused the ignition of a sealed goaf area of a mine (SANDIA, 2011). In addition there is a long history of lightning related incidents in South African coal mines (Geldenhuys, 1985). Fortunately in those cases no lives were lost. The event at Blakefield South has suggested that there may be the potential for ignition to occur in an active longwall goaf. The potential for a lightning strike to ignite a flammable atmosphere in an underground coal mine has been demonstrated from the past experience both here and overseas. It requires three things: • Lightning • A mechanism to convey the lightning underground to the flammable atmosphere • A flammable atmosphere."

Jan 1, 2016

By T. Wisdom, D. Romo, G. Seale, R. Jansen

Thickening remains relatively misunderstood since it is typically near the end of the process and not directly involved in metal recovery. When operating well, thickeners are ignored and left to run independently, the ‘out of sight, out of mind’ phenomena. However, when operating poorly, there is a lack of basic understanding and remedial actions to solve issues are reactionary rather than proactively addressing shortcomings. This series of papers breaks down in sequential order the stepped phases required to gain an appreciation and thorough understanding of the science behind thickeners, and key thickener components, and basic troubleshooting skills. This second paper starts with identifying the different approaches to thickener test work including static and dynamic settling tests followed by high-rate versus paste thickening. Complimentary to test work, the mechanisms surrounding coagulation and flocculation are presented and explained. The basic mechanisms for coagulation and flocculation are discussed to support the different test work approaches and provide the reader with the basic background.

Mar 2, 2022

By A. G. Journel

The regionalization of tungsten grades at the deposit represents an ideal case for anisotropic hole-effect variogram modelling. The modelling technique is presented step-by-step and the consequences of the model on block kriging are indicated.

Jan 1, 1982