Search Documents

By K. Sasaki

Diffusion phenomena in mine airways are important to trace gas and dust introduced into mine ventilation flows. Authors have carried out tracer gas measurements to check mine ventilation using concentration-time curves measured in mine airways, however dispersion mechanism to enhance effective diffusion have not been cleared. A numerical model using discrete tracer points dosed into tube flow has been presented to simulate their movements in consideration of turbulent velocity profile and fluctuation. Numerical simulations have been carried out to predict distributions of dosed points in tube flows with turbulent velocity profile, turbulent intensity profile and Reynolds stress. The numerical simulation results show that a combination of turbulent velocity profile and fluctuation creates extremely large dispersion of points in longitudinal direction and concentration curve with long tail was observed. This dispersion by velocity profile and fluctuation contributes large effective diffusion coefficient compared with original diffusion coefficient dominating in uniform velocity fields. Furthermore, the effect of Reynolds stress on the concentration-time curves is discussed.

Jan 1, 2009

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

By Jeremy Theys

The Sacramento Regional County Sanitation District (SRCSD) is improving the sewer system in the Natomas area of Sacramento, CA. The Upper Northwest Interceptor (UNWI) system is an ongoing series of tunnel pipeline projects that will provide sewer conveyance for all residents of northeast Sacramento County to the New Natomas Pumping Station, located North of downtown Sacramento, also in the city of Sacramento limits. The New Natomas Pumping Station then carries wastewater flowsto the Sacramento Regional Wastewater Treatment Plant in Elk Grove via the existing Lower Northwest Interceptor. The Joint Venture of Traylor Brothers, inc. and J.F. Shea (TSJV) were awarded the UNWI 1&2 project in late September, 2007. The planned 5.8 km (3.65 mile) construction route for UNWI 1&2 begins at the New Natomas Pump Station and runs north along the East Drainage Canal to the begin-ning of UNWI 3&4 at Bridgecross Drive. UNWI 1&2 includes approximately 5.8 km (19,240 feet) of 3.65 m (144 inch) inside diameter pipe using Earth Pressure Balance Tunneling Methods. The project also includes 16.76 m (55 feet) of 3.04 m (120-inch) diameter interceptor pipeline, twenty three access manholes spaced approximately 305 m (1,000 feet) apart along the alignment, a 2.13 m (84-inch) by 3.65 m (144-inch) transition structure, a 3.65 m (144-inch) by 3.04 m (120-inch) transition structure, and the connection of three existing sanitary sewer lines to the interceptor.

By R. Gensemer

A number of state and federal agencies are calling for development of aquatic life criteria for conductivity. These aquatic life criteria or ?benchmarks? are based on observed correlations between conductivity and benthic macroinvertebrate community composition, generally measured by composite metrics or indices. However, development of an aquatic life criterion for a composite variable like conductivity is made difficult by a number of factors. Based on a database from West Virginia, observed patterns of invertebrate community composition versus conductivity may instead be related to a combination of abiotic (e.g., ionic composition, habitat) and biotic (e.g., life history, colonization potential) factors. Many benthic invertebrate taxa also do not respond to increasing conductivity in a consistent relationship. Many states have determined that a composite variable, like conductivity or TDS, is not appropriate for criteria development, as many studies have shown that toxicity varies as a function of ion composition and can be mitigated by elevated hardness. We conclude that the relationships between conductivity and changes in benthic macroinvertebrate community composition are neither strong nor reliable enough to warrant derivation of a criterion based solely on conductivity.

Jan 1, 2011

By H. H. Murray

Clay minerals are one of the more important industrial minerals. They are used in many products and because of different specifications may require special processing which can be either wet or dry. The clays discussed are bentonites, kaolins including ball clays, and palygorskite (attapulgite). In order to design a process flow sheet for these clay minerals, the physical, chemical, mineralogical, and optical properties need to be evaluated. Each species of clay minerals require a group of special tests which are described in this paper.

Jan 1, 2009

By G. Baldermann, Hüttenrauch

Occupational health and safety are an important tool to increase a company’s economic efficiency. The integration of safety-related tasks into the overall structure of entrepreneurial tasks is an inalienable requirement for the sustainable achievement of positive effects. Investments into technical and personnel occupational safety that are tied in a streamlined organizational structure guarantee the improvement of defined indicators. The labor force is of central importance. Its added value ought to be ensured. It is necessary to move away from the employees‘ hazard awareness towards a safety awareness including many other aspects in order to save costs in the long run.

Jan 1, 2005

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By J. Kern, M. Cain, T. Torries

Until recently, the generation of electricity was regulated in all states and the value of generation assets in a regulatory environment for ad valorem taxation were based largely on the book value of the plant plus the rate of return on capital allowed by the state regulatory agency. This method of appraising utility generation assets is inappropriate in a competitive environment because past capital expenditures are not relevant in a competitive environment. However, it is not clear what valuation methods are appropriate after restructuring. This paper identifies key problems and advantages of other appraisal methodologies and makes comments on various valuation and taxation methods.

Jan 1, 2001

By J. D. Potts

Installation of a horizontal air blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong coanda effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector to bailing airflow ratio, and a 5.1-cm (2-in) gap between the shroud and ground. The shelf was 15.2-cm (6-in) wide and located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2009

By M. N. Chandraprabha

This paper discusses the role of mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans on the beneficiation of arsenopyrite containing multisulfides (pyrite and chalcopyrite). Adaptation to minerals altered the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed.

Jan 1, 2009

By L. Tercero Espinoza, F. Marscheider-Weidemann, C. Gandenberger

"A reliable supply of non-energy raw materials is a precondition for the functioning of the European economy. In line with its importance, the issue of raw materials supply has become more prominent in the past years, especially owing to turbulent raw material markets. However, these turbulences are not due to depletion of the geological resources but to a missmatch of (expected) supply and (expected) demand, with several interacting factors influencing the markets both from the supply as well as from the demand side. A recent evaluation, published in June 2010 within the framework of the EU Raw Materials Initiative, sought to bring together these two sides of raw material markets and asked the question "which raw materials are critical for the EU?" Herein we present the methodology used by the Ad-hoc Working Group on Defining Critical Raw Materials and the results obtained, complemented by results from the study "Raw Materials for Emerging Technologies"."

Jan 1, 2011

By K. A. Larsen, J. L. Ariail, C. M. LaRosa

This article discusses the evolution of U.S. laws and policies towards environmental remediation at mine lands over the last 20years, the opportunities that these changes present for reuse, and the remaining challenges associated with community capacity for effective reuse planning and implementation. Emerging initiatives by the U.S. Environmental Protection Agency and Department of Interior for addressing these challenges are discussed.

Jan 1, 2004

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005

By Raquel Costa, Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, Ana Filipa Marques, Andreia Afonso, Maria Ana Martins, António Calado, Luísa Pinto Ribeiro

Since its formation in 2004, the Task Group for the Extension of the Continental Shelf (EMEPC) has been collecting hydrographic, geological and geophysical data to support the extension of the continental shelf beyond 200 NM. In 2008, the EMEPC acquired a 6,000 m rated ROV named "Luso" and has been cooperating with several national and international institutions to increase and improve its operational capabilities to conduct research on deep-sea minerals. The Portuguese continental shelf corresponds to a broad area of the seafloor encompassing different physiographic domains: the mid-Atlantic ridge system, abyssal plains and numerous seamounts. From 2008 to the present, the mid- Atlantic ridge and seamounts have been the most visited sites with the ROV "Luso". Several hydrothermal vent sites are known to occur along the mid-Atlantic ridge to the south of the Azores archipelago and mostly within the Portuguese EEZ. Vent fields were also discovered in the extended continental shelf, namely the Rainbow and the Moytirra sites located to south and to the north of the Azores archipelago, respectively. The most studied seamounts correspond to those forming the Great Meteor chain and the Madeira- Tore rise. All these visited sites are related either with the occurrence of polymetallic sulphides or cobalt rich Fe-Mn crusts and the opportunities to further pursue their exploration will be discussed.

Sep 1, 2014

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By W. P. Diamond, S. L. Cario, F. Garcia, J. D. Byars, T. P. Mucho

The National Institute for Occupational Safety and Health (NIOSH) has been conducting research at a Pittsburgh Coalbed longwall mine to evaluate and optimize bleeder ventilation and gob gas venthole longwall methane control systems. Gas flow into these two methane control systems was investigated using a combination of Sulphur Hexafluoride (SF6)tracer gas studies and gob venthole pressure monitoring experiments. The insights gained from this research has facilitated the development of a longwall subsided strata methane control system conceptual model. This model provides the basis for design suggestions to increase the efficiency of the gob gas venthole system to permit the bleeder ventilation system to become a "safety net" for methane control.

Jan 1, 2000

By M. S. Riyazulla

A model of a new laboratory magnetic separator has been conceived to cater the needs of process engineers and mineralogists world over engaged in mineral characterization and beneficiation. It would be essentially a laboratory instrument for the separation and concentration of various ferro and non-magnetic minerals. Based on the basic concept of Frantz Isodynamic Magnetic Separator, the new separator conceived would not only speed up the work of a process mineralogist and save the energy, but it would effectively separate and sequentially produce about fourteen fractions at a time. In the present paper, the probable operational procedures and the design have been discussed in detail for the various mining companies to assess its economic feasibility. If it could be fabricated, it would have a worldwide market The concept has been patented in author?s name in India.

Jan 1, 2009

By W. J. Nokleberg, B. A. Bouley, T. K. Bundtzen

Central Alaska contains a wide variety of pre-, syn-, and post -accretionary mineral deposits that are related to the growth and evolution of the north-west North American continental margin. Withinpre-accretionary terranes, the Devonian-Carboniferous, carbonate platform-hosted MVT zinc-lead deposits of the Kandik and Reef Ridge districts in central Alaska, and the Devonian-Mississippian volcanogenic massive sulfide (VMS) polymetallic deposits of the Bonnifield, and Delta mineral belts of eastern Interior Alaska have received the most exploration interest to date. Syn-accretionary rift related, mafic and ultramafic sill swarms and zoned plutons of the Kluane-Nikolai igneous belt are currently being explored for Ni-Cu-Co-PGE deposits. Syn-accretionary granitoid complexes in the PurcellMountains, Illinois Creek, and Sitylemenkat areas have been explored for uranium-REE-gold, and tin-silver mineralization respectivelyPost-accretionary granitoid intrusions and associated volcanic fields that range in age from mid-Cretaceous to early Tertiary contain significant gold-silver-polymetallic resources in the East Central Alaska, Hogatza, and Kuskokwim Mineral belts. Collectively the three main post-accretionary plutonic/volcanic belts of central Alaska are part of the Tintina Gold Province, where exploration since 1990has identified about 848 tonnes gold.

Jan 1, 2000

By R. T. Langland

The U.S. Bureau of Mines has conducted underground tests and computer analyses to study coal mine roof behavior. Southern Ohio Coal Company provided test sites it) their Heigs mines located near Athens, Ohio. Testing apparatus was adapted for monitoring roof behavior at the face of mining from a remote surface location. Finite element analyses were applied to study the structural conditions present. Test sites were located at three different intersections of entries and crosscuts of the room-and-pillar mine. Electrical read-out instruments were used to record roof bolt loads, roof sag, and roof-floor convergence. They were installed during the roof bolting cycle of a conventional mining section and data was recorded for several months. Normal mining operations continued throughout the test period with minimal interruptions due to the installation and monitoring of the instruments. A computerized data acquisition system, partly underground, partly on surface, permitted continuous monitoring of data and its retrieval, display, manipulation, and storage. The finite element code used to model the test sites accounted for three-dimensional geometry, nonlinear material behavior, and the mining excavation and bolt installation sequences. Results of the test are highly variable. Comparable values between test and analysis results were obtained by applying statistical averaging of. roof test data. Results of the analyses indicate that bolts have a lesser effect on the gross behavior of mine roofs than has been indicated and that bolt load changes are strongly influenced by mining excavation sequence, bolt-placement sequence, and face distance

Jan 1, 1977

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, NV began large-scale production in 1977. During 2008 Round Mountain Gold Corp. (RMGC) relocated the primary crusher facility approximately 300 m (1,000 ft) to make room for the next phase of openpit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket. RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17-m- (56-ft-) high mechanically-stabilized embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, CO. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design and construction of the MSE wall.

Jan 1, 2010