Search Documents

By Jr. Wallace

This paper describes the importance of mine ventilation and air conditioning in the operation of a nuclear waste repository. It discusses the impact of ventilation on determining the number and size of shafts and access drifts to and within a repository horizon. The paper also describes the need to maintain separate ventilation systems for waste emplacement and construction operations. The requirement to have filtration capabilities for exhaust air from waste emplacement areas is discussed. Because radioactive high level waste will induce high temperatures in the emplacement drifts, the ability to cool an emplacement drift for re-entry requirements is important. The paper discusses strategies to cool an emplacement drift and the possibility of using continuous airflow to control temperatures in these drifts.

Jan 1, 1991

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does' not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By M. W. Springett

During the 1970's geostatisticians were often accused of not paying sufficient attention to geologic features in the computerised generation of ore reserves. Unfortunately this charge was all -too-often justified and the results of such studies tended to be oversimplified and failed to reveal the full potential of computerised reserve estimation and geostatistical methods. There were some notable exceptions to this trend. Techniques were described that paid a great deal of respect to the geologic characteristics peculiar to certain deposits (Rendu J-M, 1984, Barnes T. E., 1982). At Gold Fields several techniques have been developed for handling the geologic characteristics of ore bodies for reserve estimation purposes. These have developed over time and the evolution of their adoption has been a reflection of our own learning experience from the practical application of computerised reserve estimation on many precious metal s deposits. Problems Typical problems that have been experienced by ourselves and which we have learned to guard against and watch for are: ? "smearing" at geologic contacts ? confusion caused by disparate "selective mining unit sizes" and block sizes ? conflicting estimates generated by field staff using various versions of the polygonal method ? problems in generating meaningful variograms

Jan 1, 1985

By Robert Smith

Deposits are global, said Barrick Gold's Smith. This means that the mineral industry, by necessity, is global. "Manufacturers have considerable freedom to decide exactly where they wish to produce whatever it is that they sell," he said. "What we sell, on the other hand, must be produced where nature chose to lay it down. The question is not so much, whether to go global, as when to do it and how to go about it." The timing of international expansion depends on external factors, often political, Smith said, and on internal ones that relate to the company's size and stage of development. "In deciding how to expand, a company is largely deciding how to adapt its existing business strategy to activity on the world stage," he said Barrick entered 1997 with 1.58 kt (51 million oz) of reserves, Smith said, annual production of 93.3 t (3 mil- lion oz) and cash flow of $463 million. Reserves in- creased 40% in 1996 and production will begin to rise again significantly in 1999. "We believe our fundamental strategy is responsible for our early development and subsequent success," he said. Barrick entered the gold-mining industry in 1983. Its corporate mandate was to create shareholder value, Smith said. From the beginning, the company took a different approach - businesslike, entrepreneurial, strategic and focused. "Many mining companies start out with a technical team and develop business and financial expertise thereafter," Smith said. "In 1983, Barrick had the business people, and then moved into mining." First, it acquired part interest in two small operations, one in Alaska and one in Ontario. Then, in 1984, it merged with Camflo Mines, which operated a low-cost underground operation in Quebec.

Jan 1, 1997

By W. B. Collingwood, D. Misra, T. Ghosh, S. Bandopadhyay

Understanding the variability of sulfur and calorific value in coal seams is critical to planning mining operations and marketing the mined coal. In this study, statistical and geostatistical techniques were used to explore the underlying spatial trends present in a large coal deposit. Eight prediction models for the sulfur content of the coal seam were developed. Six of the models were created using geostatistical techniques, while the remaining two models were created using other techniques. The performance of each model was examined by conducting cross validation exercises. The results of the study showed that very pronounced trends and anisotropies were present in the sample data, which had to be accounted for in the modeling. The study found that a cokriging model using sulfur and ash is the best prediction model for predicting sulfur content in this coal reserve.

Jan 1, 2014

By T. A. Gray

The environmental liabilities of coal waste disposal sites can have a major impact on a mining project's economic viability. Developing a waste disposal site is no longer simply an exercise in completing paperwork to obtain a permit, with the proliferation of environmental regulations in recent years, managing disposal sites now requires design creativity, short term and long term planning and detailed monitoring to maximize the benefits to the mining company. Operating costs and future capital costs for expansion of existing sites, new site development and regulatory compliance should be reviewed periodically and considered in the overall management plan. This paper discusses various management methods that are being employed in the industry to improve waste disposal operations both environmentally and profitably.

Jan 1, 1994

By A. C. Lordi

Present industrial plant design is influenced by motivators beyond the usual powerful one, creativity, on which Consultants thrive. The respected, although annoying, ever-present Return on Invested Capital becomes even more significant with anticipated escalation. Government regulations are having an increasing influence as air and water protection, sound and electrical safety requirements must be met And more recently, the increasing cost and uncertain availability of energy sources are having a revolutionary affect on plant design. More than ever before, the Consulting Engineer is faced with requirements and restrictions which tax even the most original thinkers -- and the result is good. This paper includes a brief review of recent trends in Cement Plant Engineering Design.

Jan 1, 1975

By R. J. Sweigard

Estimated costs and revenues can be used in the evaluation of post- mining land use alternatives. However, post-mining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There- fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact upon each alternative under consideration. In this paper, a method is presented which employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1986

By J. L. Hoover, P. W. Conrad, J. Downey, S. Parrow, S. Rosenthal

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect drill bit wear and use that equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel software package. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By D. G. Chedgy

Careful consideration is given to the type of cleaning equipment and control sys- teas to be used when selecting circuits for wash-ing fine coal (28M x 0 size fraction). However, the desliming, declaying and sizing procedures required to ensure efficient operation normally are not evaluated in sufficient detail resulting in disappointing system performance. This paper details desliming and dewatering circuit design which is extremely effective based on recent test data. The circuit maintains control of the 28M x 0 (declayed) size fraction with minimal misplaced material and maximized circuit efficiency. A discussion of circuit design parameters and control systems, as well as results from the testing program, are included in this text.

Jan 1, 1986

By J. A. Madonna

Universities and colleges in three countries -Australia, Canada and the United States, recognized the need to establish and reorganize geoscience programs at the vocational and two-year technical levels. To accomplish this goal, a cooperative study with industry in one state or province from each country was initiated. These include 1) Tasmania, Australia, 2) British Columbia, Canada and 3) Alaska, United States. Over one hundred mineral exploration companies and private consultants cooperated in the study by providing information regarding their specific training needs for support personnel, the data gathered has been used to identify training area for semi-skilled, skilled and technical personnel in geophysics, including, but not limited to, geo-logical skills, geophysical skills, surveying skills, environ-mental skills, and computer skills. With areas of major educational need defined for geophysical exploration, an educational field skills model has been developed for the three levels of training. The depth of each level of education and the training objectives for the work force at each level will he discussed.

Jan 1, 1992

By Ching-Yi Tsai

The effect of various constituents on the pyrolysis and combustion of a pulverized coal in an entrained-flow reactor has been inves¬tigated. Predicted time-temperature histories of the coal' particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm. This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate prior to ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of a HVA bituminous coal which were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite rich samples.

Jan 1, 1984

By Jeff LeBlanc, George Gutierrez, Carl Pitzer

The Bay Park Conveyance Project was one of the largest microtunneling and rehab projects in the United States at the time of completion. The completed project conveys treated water from the South Shore Water Reclamation Facility located in Nassau County, New York, which currently discharges an average of 50 million gallons per day (MGD) of treated water into Reynolds Channel, to the Cedar Creek Water Pollution Control Plant (WPCP) ocean outfall pipe. The pipe carrying treated wastewater was installed approximately 20–60 feet below the surface. The treated wastewater is conveyed via microtunnel construction of a 2-mile long force main from the South Shore Water Reclamation Facility to an existing aqueduct under the Sunrise Highway, the rehabilitation of an 7.3-mile stretch of the aqueduct via sliplining, and construction via microtunnel of a 1.6-mile-long force main to connect the rehabilitated aqueduct to the existing Cedar Creek Water Pollution Control Plant (WPCP) outfall, which discharges and diffuses treated water three miles offshore in the Atlantic Ocean. This paper will review the Design-Build requirements, the chosen innovative solutions during planning for the micro tunneling portion of the project and review the microtunnel construction on the project.

Jun 23, 2024

By D. C. Myntti

An open pit mining equipment maintenance program, in order to be successful, must have many active segments covering the full range of equipment selection, trained personnel, repair facilities, preventive maintenance programs, warehousing, interdepartmental cooperation, paperwork and effective communications. The mine maintenance program is required to protect company assets Which are units of equipment generating revenue. The program should result in reduced unscheduled equipment downtime, increased equipment productivity rates, and decreased unit operating costs. Current maintenance problems; maintenance effectiveness and future projections on equipment maintenance are discussed. Equipment maintenance is big business and the maintenance department is a full-time partner in the mining venture.

Jan 1, 1978

By Steve Skelhorn, Dan Ifrim

"A tunnel project poses many challenges; the operation of the Tunnel Boring Machine (TBM) being one of them. Mechanized tunneling is known as a safe and effective alternative to other methods in terms of schedule and cost; however, efficiency can be severely affected by a bad TBM selection and qualification and employment of inexperienced operators. The success of a mechanized tunneling project involves a comprehensive and interdisciplinary consideration of all contributing factors such as TBM technical specification and selection, TBM design and procurement including ancillary equipment and tunnel linings. The tunnel equipment selection along with the operation can make or break the project. The objective of this paper is to address the importance of the skills and qualifications of the TBM crew with particularity to the TBM Operator. The study includes the Owner and Consultant involvement in the selection and pre-qualification of the TBM crew and specifically the TBM operator as well as the role of Contractor and TBM manufacturer in TBM operator training. This paper also analyzes the possibility of issuing a TBM operator certification, and discusses the benefits and significance of periodic training and certification programs. INTRODUCTION Training in the tunneling industry is not a new topic. The industry continues to evolve and become more complex with technology advances and expansion of mechanical tunnelling to mechanized shaft construction, large diameter drilling and mining industry applications. The need for professionals trained to operate mechanized tunnelling equipment is ever increasing, while there is a significant number of veterans who will be ageing out in the next 5 years. Consequently attracting young professional is a very important aspect of sustaining a qualified pool of professionals. For any given tunnel project, the owner and the engineer spend up to several years, studying the ground conditions during preliminary and final design. Post contract award the contractor spend additional months studying the ground again to develop the optimum means and methods for construction. All this time and money spent at the beginning of the project has the purpose of developing the optimum tunnel design, assessing the risk associated and implementing mitigation measures to reduce risks to acceptable levels. Following the tunnel design process, sophisticated TBMs are being specified and sourced to ensure the best tool for the job. The question raises here: Are there available experienced/trained professionals capable of operating these sophisticated machines?"

Jan 1, 2016

By John S. Carman

Our industry is in trouble. Real trouble. It has never been an easy, secure business. But to-day it is engulfed in revolutionary currents. No longer can there be reliance upon the checks and balances of market forces. Supply and demand largely dictated the economics of business enterprise in simpler days. To-day politics, in particular nationalism become increasingly dominant. And as governments expand and put out tentacles of interference in the direction of the mining industry, far too little understanding is evidenced as to how that industry works. Then there is something which is relatively new -stagflation. As the prices of minerals falls, the capital investment required for new extractive facilities soars at rates which far outdistance those which are cited by governments to indicate the magnitude of inflation. To illustrate; 1) In 1971 it was calculated that $355 million would be required to bring the Cuajone property in Peru into production. Five years later that stage was reached at a cost of $680 million. 2) With the Caridad mine in Mexico, estimated capital investment doubled between 1971 and 1976. 3) The requirements calculated for Cerro Colorado in Panama have risen in two years from $560 to $800. 4) The budget of $240 million for Sar Chesmeh in Iran in 1971 had become $500 million by 1976.

Jan 1, 1977

By Monica Campos, Jose Mujica, Maria Campos

The extraction and processing of metals and other minerals have played an important role in economic, political, and social development worldwide, from the early stages of prehistory to the present day (Gosner, 2020). In other words, mining has been a fundamental part of human civilization, providing the raw materials necessary for technological, infrastructure, and industrial advances. As society progresses, the importance of mining continues to grow, supporting the development of everything from the smallest electronic devices to the tallest skyscrapers (The Importance Of Mining In Modern Society, 2024). The mining industry is closely linked to a country’s economy and activities related to natural resources. The economy of a nation is connected to its extractive industries (Moreira & McMahon, 2014), which have seen dramatic growth in recent years (Pietrobelli et al., 2018). In a context of increasing demand for natural resources, driven by the development of emerging technologies, the expansion of infrastructure, and the foundation of engineering achievements for the coming decades (Importance Of Mining - Minerals Education Coalition, 2024), mining should focus efforts on global development, requiring a comprehensive approach to sustainability that addresses the planet’s needs and protects the well-being, primarily, of the communities and environments where mining operations take place (Figari, 2024). In these areas, diversity and inclusion should be promoted, thus fostering equitable and sustainable development. Speaking of sustainable development, diversity, and inclusion brings us to an interesting topic: the Sustainable Development Goals (SDGs), also known as the Global Goals, which could serve as a key framework for fostering a strong social management culture in mining. The SDGs were adopted by the United Nations in 2015 as a universal call to end poverty, protect the planet, and ensure that all people enjoy peace and prosperity by 2030 (Sustainable Development Goals, n.d.). Companies have compelling reasons to align their actions with the SDGs, as their long-term success depends on healthy communities. This is a major challenge and requires collaborative efforts (Singh & Rahman, 2021). As Fraser (2021) mentions, achieving more sustainable outcomes may involve mining companies and communities working together collaboratively. This research proposes an innovative approach: Inclusive Mining for Sustainable Development, which aims not only to maximize economic profitability but also to promote social and environmental well-being by integrating the United Nations’ Sustainable Development Goals (SDGs), primarily focused on diversity and inclusion. This can be achieved through the implementation of a key value-added initiative for mining companies: the Creation and operation of a corporate volunteering program aimed at developing and executing inclusive practices to promote gender equality, the inclusion of local communities and indigenous peoples, and accessibility for people with disabilities. This proposal will educate employees and stakeholders about sustainability and promote concrete actions through corporate volunteering to strengthen the mining company’s commitment to community development, improve social relations, and advance toward achieving the United Nations’ Sustainable Development Goals, establishing the company as a global change agent.

Feb 1, 2025

By Guillermo Krstulovich

Pillar strength is a fundamental variable in the design of room and pillar mining. A number of researchers have investigated the strength of mine pillars by loading cubical, cylindrical and rectangular model pillars to failure in a compression testing machine (1). Several of these researchers have observed an increase in the compressive strength of model pillar with an increase in friction at the platen-specimen interface (2, 3, 4, 5). It has been postulated that the friction prevents lateral expansion of the specimen, thereby exerting a confining pressure at the interface. Seldenrath and Gramberg in their work with cylindrical specimens of limestone and marble noted that the effect of clamping the ends of the specimens, i.e., to restrict lateral movement of the specimen face, was to increase the compressive strength about 10% for marble and from 50-75% for the limestone, as compared to the same type of specimens when tested with the end planes free (6). No attempt was made to determine the confining pressure exerted by the clamps. In recent years, Bureau of Mines has conducted an extensive study, similar to Seldenrath and Gramberg's, with dog bone specimens. The confining pressure exerted by the clamps was determined and an increase in the compressive strength with increasing confining pressure noted (7, 8).

Jan 1, 1970

By Ayman A. El‑Midany, Hassan E. El‑Shall, Kerri‑Ann A. Hue

Modification of clays is necessary for the zearalenone (ZEN), as long-chain mycotoxins, removal. The organic-cations were usually used to modify the clay hydrophobicity to accommodate the large mycotoxin molecules. In this study, tri capryl methylammonium (TCMA) chloride and common corn oil were used in clay modification. Several characterization techniques such as XRD, FTIR, and TGA were used to identify the d-spacing changes after modification either by TCMA or corn oil. The results of applying the TCMA-corn oil-modified clays in ZEN removal indicated a noticeable improvement where more than 90% of ZEN could be removed in vitro at acidic and neutral pH values. The success of eliminating a high percentage of ZEN molecules is due to the expansion of intergallery spacing as a result of TCMA surfactant intercalation within the clayforming layers. The removal percentage does not depend only on pH but also on the amount of clay used. In addition, the ZEN removal in the presence of corn oil is better at acidic pH and small clay amount where the ZEN can be fully removed.

Sep 27, 2021

By Jeffrey Peterson, John Beesley, Martino Scialpi, John Cassidy

The DC Clean Rivers Project is DC Water's ongoing program to capture and treat combined sewer overflows (CSOs) during rainfall before they reach the District waterways. The Anacostia River system was designed to reduce CSOs into the Anacostia River and includes the Blue Plains Tunnel, Anacostia River Tunnel, First Street Tunnel, and Northeast Boundary Tunnel. A portion of the Anacostia River system was commissioned in March 2018 and the final component, the Northeast Boundary Tunnel, was placed in operation on September 15, 2023. This paper provides a summary of the experience gained during construction of this +$2.9 billion project, an overview of the system performance since its activation in 2018, and a look-ahead to the next phase of the DC Clean Rivers program: the Potomac River Tunnel.

Jun 23, 2024