Search Documents

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By Y. Pan, P. Tukkaraja, R. BHARGAVA, V.V.S. VYTLA, S.J. SRIDHARAN

Panel caving is an underground bulk mining method that uses gravitational force to mine massive, steeply dipping and deep-seated ore deposits at lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. As caving is a dynamic process, designing an effective ventilation system is challenging; therefore, estimating the airflow resistance offered by the broken rock inside the cave is critical. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using the computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

Nov 1, 2022

By V. A. Evans

The preparation of a paper reporting fluorspar economics in the United States at one point in time could have been somewhat complicated be- cause of the number of producers, both large and small, that derived production from different locations throughout the Western U. S. and the Southern Illinois and Western Kentucky fluorspar districts . Companies such as Allied Chemical and William- son Mining operated in the Jamestown district of Colorado. In Walden and Salida, Colorado, the Colorado Fluorspar Company operated mines and mills.

Jan 1, 1986

By N. Careddu

In recent years, slabs with a rough surface have captured a large share of the ornamental stone market. However, the main technologies used for this type of treatment are based on mechanical shock (bush-hammering) or thermal treatment (flaming or flame-finishing). These traditional technologies are widely used, but have many limitations that decrease their usefulness. The purpose of this study was to develop a technology that enhances the natural colors of the rock and produces a rough surface without compromising its mechanical characteristics, in contrast to traditional technologies. This report shows the technical, economic and aesthetic results obtained with a new water-jet treatment and compares it with competing technologies.

Jul 1, 2010

By Dr. R. W. Mead

There are two basic problems when one attempts to separate a solution of metal ions utilizing a chelation-solvent extraction cascade (commonly called liquid ion exchange). First, it is impossible to produce any great degree of separation unless the separation factor (also called selectivity, which is the ratio of the distribution coefficients) is very large. Second, the richest possible extracted product, using an infinite number of equilibrium stages, is at best only in equilibrium with the feed solution. These factors combined with equipment design considerations have led to a situation where only the most selective chelating agents are applicable to economic industrial operations. The authors know that distillation techniques are used routinely to separate compounds with nearly identical relative volatilities and that there should be a way of operating solvent extraction cascades in an analogous manner to obtain separations of metal ions. The advantage of this approach would be that solutions of metal ions of any desired purity could be obtained even if the separation factor was close to unity. This paper presents this idea and suggests some possible applications.

Jan 1, 1977

By Hendri Silaen, Charles Leatemia, Monang Napitupulu, John Kamarea, Arwin Edijanto, Riza Hasan, Avesiena Primadiansyah

The Deep Mill Level Zone (DMLZ) is the fourth panel cave mine in the East Ertsberg Skarn System, (EESS) which lies 500 m below the producing Deep Ore Zone (DOZ) mine and up to 1,700 m below the surface. The interaction between the DMLZ and DOZ is occurring as the DMLZ cave grows vertically toward the DOZ footprint. During this process, a rapid change in the global mine system stress is anticipated. This change is forecasted to drive substantial changes in the magnitude and direction of principal stresses in the DMLZ and DOZ mines at PT Freeport Indonesia. These changes will bring the mine system closer to the ultimate capacity of the excavations and can result in significant impacts to mine stability if not managed. Critical to this management, is understanding cave growth and locations, as well as how these changes will impact stress conditions.

Apr 26, 2022

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988

By C. C. Clark

The National Institute for Occupational Safety and Health (NIOSH), Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system there is a need to know when the material has developed a threshold early compressive strength of approximately 1 MPa (145 psi) for safe re-entry of miner and machine into shotcreted mine workings. This equates to the material having developed enough strength to be self-supporting and allow for emplacement of the remaining support elements that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on-site in the first six hours after application using the ASTM C 116-90 (1990) standard. These advances were demonstrated in tests on five commercially available shotcrete mixes, sprayed as dry shotcrete using the field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. The findings of this NIOSH research for determining shotcrete early strength can improve mine safety by providing a method for determining initial site specific material property values to be used for design and as a means to conduct on-site quality control and monitoring during production.

Jan 1, 2010

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau ofMines (USBM) have given a significant effort over the past four decades in researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers performing manual bagging and palletizing of 50- to 100-pound bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper will provide an overview of available dust control technologies for bagging operations and present the findings of a recent case study that was conducted at four different industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation will also be performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

Apr 3, 2020

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

By Richard O. Rouse

Today, I want to challenge this audience by charging each of you to be a greater manager and superior engineer to manage and engineer our way through the 1980's and profitably overcome all the present and proposed government regulations. May of the present and proposed regulations will tax you and your company's management and engineering to the brink of physical and monetary exhaustion, but I believe we can succeed and coal can be America's answer to her hungry energy needs. To put our 1980's challenge into perspective, I want to give two great challenges we must overcome. First - We must improve on our process of compliance to new government regulations in the technical and equipment end of our industry. The Lord said, "Let There Be Light". MSHA said, "Let there be light in underground coal mines". Since that time, we have lived through an unmanageable and tremendously costly period of compliance.

Jan 1, 1980

By Yi Zheng

Under normal circumstances, methane released along a longwall face represents only 10%-20% of the total me- thane emitted from the entire longwall panel. However, there might be a sudden surge of methane at the face which may cause a potential problem because the friction from shearer cutting, support movement, and scraper conveyor dragging can be ready ignition sources. Therefore, to predict the distribution of methane will be critical to prevent possible explosions. In this paper, methane dispersion patterns along a lognwall face are simulated under normal and abnormal conditions. With the simulation of methane released from the face, around shearer drum, and from the broken coal on the conveyor, places with possible high methane content can be identified by different phases of working process and shearer positions. Local ventilation measures are evaluated so precautionary measures can be planned ahead.

Jan 1, 2012

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

6.1 PRINCIPLES OF PLANNING GROUTING OPERATIONS FOR SHAFTS, DRIFTS AND TUNNELS The planning of integrated grouting of vertical, inclined or horizontal underground workings in saturated, fractured rock includes the following phases: 1. Planning for the collection and analysis of geological information concerning the characteristics of the struc¬tural deformation(s) that produced the details of the frac¬ture system being studied. 2. Planning for the acquisition of initial hydrogeological information produced by the flowmetric and hydrody¬namic investigations (described in Chapters 2 and 3). 3. Computing the initial engineering calculations of the ex¬pected or planned dimensions of the isolation curtains for each water-producing stratum (fracture zone) and the expected areal spreading pattern of the grout in each of these water-producing horizons. The selection of the lo¬cations, the initial optimal number of holes and the vol¬ume of grout needed to create each isolation curtain also are included in this phase. 4. The selection or development of a grout formula for the specific hydrogeological conditions that exist at the site. 5. Identification of a resource (deposit) required to produce the grouting clay. The planning of grouting operations must be supported by the acquisition of all necessary initial data, which in¬cludes: 1. The geographic location and administrative responsibil¬ity (ownership and regulatory constraints) of the mineral deposit and any peculiar features of the area where ex¬cavation of the underground workings is planned. The surface relief, the hydrographic network of the region, and the local climatic conditions must be evaluated prior to planning for buildings and waste discharges if any. 2. The economic status of the region, the available trans¬portation, the nature of the energy base, the water and heat supply sources, the location of construction mate¬rials suitable for making the grout all must be deter¬mined. 3. The geological and hydrogeological characterization of the work site must be accomplished. 4. The technical features of the shaft(s) and underground works must be characterized. 5. The organization's principal initial design plan features and the construction sequence of all buildings and struc¬tures must be developed. These must be correlated with the organization and schedule for excavating the under¬ground works. The technical characterization of a shaft or of other un¬derground workings must contain information about the purpose of the workings, the design depth, the planned excavation procedures along with cross-sections, and the parameters of the lining, if a lining is required. The geology of the section to be penetrated must include geological data obtained from existing exploration activities at the mineral deposit and conclusions about the shaft ex¬cavation conditions obtained from drilling technical moni¬toring holes and exploration drillholes. The interpreted stratigraphic regime, including the thickness, strike and dip of each stratum, must be shown in cross-section. The tec¬tonics, including all geologic structures, must be presented by cross-sections. The bedding orientations must be used to identify anticlines, synclines, monoclines and faults. The lithologic composition and the drillability of the rock com¬prising the section must be examined. The character of the rock's fracture pattern must be presented. Finally the per¬meability, porosity and storage characteristics of each aqui¬fer must be determined by in situ hydraulic property testing (injection tests or pumping tests, as described in Chapter 3). The fracture pattern of the indurated rock is presented in reports derived from geo-exploration borehole studies and from studies of outcrops on the surface and in all nearby underground workings. The extent of each fracture zone is mapped in three dimensions. The distribution of fracture apertures, the nature of the fractures according to each litho¬logic stratum, and the relationship of bedding planes to each fracture system are all determined. Acoustic logs, downhole cameras, caliper logs, oriented core, and any other appro¬priate geophysical tools available are used to construct the data base for this purpose. The hydrogeological characterization of the geologic section to be penetrated by the workings is based on the analysis of hydrogeological data collected during the drill¬ing and testing of technical monitoring holes and from in¬formation on ground water inflow collected during the ex¬cavation of nearby underground workings, if such workings exist. The hydrogeologic characterization must contain the following information: 1. The identification of all aquifers, their thicknesses and their locations in the section, 2. The distribution of hydrostatic head in the ground water in three dimensions, 3. The coefficient of saturated hydraulic conductivity (per¬ meability) of each aquifer, 4. The porosity and storativity of each aquifer, and 5. The projected rate of water inflow into the shaft, drift or tunnel for each aquifer prior to grouting. This step is used to identify the zones to be grouted.

Jan 1, 1993

By Lok W. Home

INTRODUCTION Today, raise drilling (boring) has become the stan¬dard method of raising throughout the Western world. It is estimated that the majority of raise footage com¬pleted in 1977 was accomplished by the raise drilling method. Extensive replacement of the drill and shoot system by mechanized raise drilling has occurred be¬cause users have recognized one or more of the follow¬ing advantages. In a direct cost per meter comparison, mechanized raise drilling is economically more attractive than drilling and shooting. Mechanized raise drilling offers improved personnel safety over the drilling and shooting method. Mechanized raise drilling is a faster and more predictable method for excavation than is drilling and shooting. The raise cost per unit of length becomes less as the raise length increases, offering greater flexibility in the overall design of mines. Mechanized raise drilling provides a substantial reduction in labor requirements. 6) Mechanized raise drilling improves the working environment. 7) Mechanized raise drilling improves the rock in¬tegrity of round, unblasted raises. Increasing acceptance of the raise drilling technique is enhanced by continuing equipment development. Today, a wide range of machines and capabilities is available, machine drive systems have been improved, reliability has been increased, and cutter technology is being improved quite rapidly. Table 1 lists the four major manufacturers of raise drilling machines, cutters, and reamers, together with the approximate number of machines that each company had in operation at the end of 1977. Although Reed and Smith are major suppliers of reamers and cutters, they do not manufacture the drilling machines. Four or five other relatively minor suppliers have built machines, reamers, and cutters for raise drilling, but they did not have a substantial num¬ber of machines in the field at the end of 1977. MACHINES FOR MECHANIZED RAISE DRILLING There are three principal arrangements for making machine-bored raises. They include the use of standard raise drills, reversible raise drills, and blind-hole or box¬hole raise drills. Standard Raise Drills The standard raise drilling machine is set up on one mine level or on the surface, and a pilot hole is drilled from that level or surface to a level below. When the pilot hole has been drilled, the raise then is reamed back from the lower level to the upper level or the surface. This arrangement is illustrated in Fig. 1. Reversible Raise Drills The reversible raise drilling machine is set up on a lower level of the mine, and a pilot hole is drilled up¬ward to a higher level. The raise then is reamed back from the upper level to the lower level. This arrange¬ment is illustrated in Fig. 2. The machines used for this type of raise drilling normally are capable of being used as standard raise drills. Blind-Hole or Boxhole Raise Drills The blind-hole or boxhole raise drilling machine is set up on a lower level of the mine, and a full diameter raise is bored to a higher level without the use of a pilot hole. This type of machine is illustrated in Fig. 3. Drill Recommendations If access to upper and lower mine levels is equal, the standard raise drill should be used. The complexity of the equipment and associated handling procedures for boxhole drilling far outweigh any mechanical advantage or reduction in the number of operations, provided that access to an upper level is available. If there is good access to a lower level but only limited access to an upper level, the use of a reversible raise drill should be considered. If there is no access to an upper level, a blind-hole or boxhole raise drill is the only practical mechanized system. MACHINE SELECTION There are six major considerations in selecting a machine for raise drilling. These include operating range, cutter loading, machine structure and main¬tenance, drill string configuration, drive system, and automated controls. Operating Range As shown in Table 2 and Figs. 4 through 6, raise drilling machines are available for a wide range of hole sizes. Standard raise drill ratings range from raises of 0.9 m (3 ft) diam and 120 m (400 ft) length up to raises of 3.5 m (12 ft) diam and 900 m (3000 ft) length. Boxhole raise drilling machines are available for raises ranging from 0.9 m (3 ft) to 2 m (6 ft) diam with lengths up to 90 m (300 ft). Table 2 lists, among other criteria, the torque and thrust of typical machines; torque and thrust are the main criteria for analyzing the capacity of a machine. The raise sizes shown in Table 2 assume a condition of medium hard to hard rock formations and optimum cutter loading. The recommended raise size for a given machine can be exceeded when raising softer rock formations or when the operator is willing to accept a lower level of performance; the performance is related directly to the 1093

Jan 1, 1982

By RICKARD HANSEN

Vehicle fires in underground mines pose a certain risk for which measures to prevent or mitigate the fires are highly important. Fire protection measures can be divided into active and passive measures, where active measures require an external power to work in the event of a fire, and passive measures could include an existing partition preventing fire spread. As passive fire protection does not rely on activation, it is expected to provide high reliability and a robust solution, and should be considered during the design process. This paper investigates passive fire protection measures that could be implemented in the design of mining vehicles. It was found that passive fire protection should include the use of several measures simultaneously to ensure fire protection throughout the different phases of a fire. Threshold distances for fuel components were calculated, and it was found that combining hydraulic hoses and electrical cables resulted in larger threshold distances. A pool fire along the underside of a vehicle will pose a certain risk, and passive measures should be focused on ignition prevention, making high demands on the insulation/shielding along the underside. Any occurring tire fire may pose a challenge, and the priority should be on preventing ignition. Potential measures include shielding the wheelhouse and applying fire-resistant sealings.

By Paul Soros

Lord Robens, Chairman of the National Coal Board of England announced recently to the world press plans for construction of the largest bulk terminal in Western Europe. This should result in annual freight savings of 22.4 million dollars and between 150 and 190 million dollars of new export business. These are rather substantial amounts for any mining enterprise. Or to put it another way, opportunities to make substantial savings in the delivered price of a highly competitive commodity such as coal are few and far between. One area where such opportunities still exist is in the economical; movement of bulk materials between producer and consumer.

Jan 1, 1966

By Albert L. St. Peter

The "Old Reliable" four million pound blast in March of 1972 marked the opening, as far as is known, of serious efforts to commercialize the In Situ concept. That was a coyote shot, and it was followed by three blasts at McAlester Fuel's "Zonia" operation which were surface hole shots. As the only individual who had a principal part in all four shots, it seems to be appropriate to present experiences in the developments and evolutions of the in Situ method of ore extraction. Some of the problems will be described, along with proposals for management of such projects in the future.

Jan 1, 1976

By Thomas P. Meloy

Comminution is an old art. Unfortunately the analysis of the unit operations has been handicapped by the lack of both theoretical and experimental information. Two types of infor¬mation are needed, one an understanding of what happens when a particle breaks in a brittle manner; and two, an understanding of what happens when the daughter fragments pass through the mill. This paper is concerned with the former, the catastrophic fracture of a brittle solid. Recently, successful theoretical attacks on the frac¬ture of brittle solids have yielded significant-results. New experimental techniques are yielding insight into the physical phenomenon occurring during brittle fracture. Many of the re¬doubtable shiboliths of the last century are either being laid to rest or verified.

Jan 1, 1965

By David E. Lindorff

The impact of surface coal mining on the geologic materials and ground water in different geologic settings is being investigated by the Illinois State. Geological Survey at three abandoned surface mines in Illinois. At a site near Ottawa in La Salle County, the overburden prior to mining consisted largely of pyritic shale; sand was the major component of the overburden and spoil at a mine near Coal City, Grundy County. Clays, lacustrine silts, and some shale and limestone were the dominant premining overburden materials at a mine near Harrisburg, in Saline County. Ground-water elevations at Coal City and Harrisburg are approximately at premining levels, whereas at Ottawa they are near the base of the spoil. Ground-water quality has deteriorated at all three sites, especially at Ottawa and Harrisburg.

Jan 1, 1981

During 1993, contraction of indus¬trial economies in Germany (-2%), France (-1 %), Japan (-0.1 %), Eastern Europe (-2%) and the former Soviet Union (-13%) dimmed prospects of a robust economic recovery for North America. Some European countries that suffer from high unemployment and large government deficits have non-com¬petitive cost structures that will require long-term economic reforms to solve. Restructuring in the United States also continued in 1993. The sluggish pace of the US economic recovery, in¬troduction of federal tax increases and the persistence of high levels of unemployment did little to inspire consumer confidence. By the end of the year, however, sales of consumer durable and capital equipment began to grow. Depressed demand for minerals by industrial economies in recession was partially offset by continuing rational¬ization or abandonment of non-competi¬tive productive capacity in Eastern Eu¬rope and the former Soviet Union. Al¬though aluminum, lead, titanium sponge and zinc prices fell, increases in copper and steel consumption helped steady their prices along with prices of some alloys. Cash flow to the mining industry - the primary source of exploration funds - was therefore constrained. For many companies, exploration expendi¬tures were reallocated geographically and in terms of commodities sought.

Jan 1, 1994