Search Documents

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By M. A. Trevits

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

Jan 1, 2009

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By B. C. Lewis

Have technological advancements in underground coal mining driven people's skills to new highs or have the expanded skills of mining people driven the industry's technological advancements. Who knows? What we do know is that both our technology and our people have made meaningful and significant advancements. Overall, longwall systems continue to increase productivity and retreat faster. Globally, gate road development is the primary bottleneck in a longwall mine. The primary bottleneck in gate road development is roofbolting. Generally, roofbolting is the bottleneck in room and pillar operations as well. This paper will present an integrated manufacturer's (Joy Mining Machinery) vision of the future in comparison to current equipment performance. Particular emphasis will be placed on roofbolter technologies.

Jan 1, 1999

By Y. Q. Zhang, Y. Luo, S. S. Peng, C. T. Holland

Barrier pillars in underground coal mines could eventually be subjected to a hydraulic pressure head due to the build-up of mine water in the old workings. The pressure head could not only act as a force to destabilize the pillar but also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that in turn could accelerate the mechanical failure process of the barrier pillars. In this paper, finite element simulation approach has been employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations.

Jan 1, 2001

By K. W. Lee, C. Pound, J. Carmody, L. Petersen, C. Nelson, J. G. Cai

The feasibility of developing the Underground Science City below the Kent Ridge Park has been investigated. The primary aim of the study has been to explore the possibility of creating underground space to house a new community of research laboratories and offices. The investigation represents the first such study undertaken in Singapore for a non-military underground facility. The paper describes the geology of the Underground Science City site and illustrates the layout and plan of the Underground Science City. The geology and rock mass below the Kent Ridge Park is generally favorable for the development of an underground cavern complex. Underground Science City can be potentially developed housed in a cavern complex. Several potential development schemes are studied; with various combination of deep/shallow mined caverns of different span sizes and access options. The preferred scheme is shallow, mined room-and-pillar caverns with large spans and shaft accesses at both existing surface Science Park 1 and Science Park 2. The scheme can be potentially expanded laterally to create more underground space for new Underground Science Cities at Kent Ridge area.

Jan 1, 2001

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

By Steve Kral

Mining is a risky business. The cost of exploring for new mineral deposits is high and the success rate of finding one worthy of development is relatively low. And once a deposit is identified, there is no guarantee that it will become a mine. Mining companies have to spend a lot of time and money on due diligence, prefeasibility and feasibility studies, and sustainable development and environmental issues before deciding whether the deposit will become a profitable mine. And then there are the millions of dollars spent in developing the deposit and building a mine. No wonder the mining industry has trouble attracting investment capital. Companies take a large risk in developing reserves and investors take a similar risk in investing in them. So mining companies must be as accurate as possible in determining mineralization that makes it to reserve status. After all, reserves are a company’s most important asset and one of the critical factors analysts and funding sources look at when determining if a mine or mining company is worth the risk.

Jan 1, 2003

By Shimi Tzobery, John E. Shamma, Samuel Swartz, Gary B. Hemphill

The trapezoidal tapered ring method has made significant progress in recent years for shielded-TBM projects, excavating tunnels with high overburden, strict water tightness criteria, and multiple curve alignments. The selection of compatible tapered rings is critical for successful advancement of the tunnel, assuring efficient installation of rings, as well as prevention of ring damage and excessive leakage. Using experience from the Arrowhead Tunnels Project, this paper describes guidelines for ring selection in tunnel curves, geometric analyses that comply with criteria principals, and provides techniques developed to determine the appropriate relative key position.

Jan 1, 2005

By António Fiúza, Anthony Danko, Patrícia Leitão, Aurora Futuro, Cristina Vila, Lurdes Dinis

The average global recovery rates for processing scheelite ores by physical methods are normally in the range 50 to 70%, and it is problematic to attain a minimum grade of 60% WO3 in the concentrates without penalizing further this yield. Direct hydrometallurgical processing of low-grade concentrates or medium- to high-grade ores may become an interesting global economic alternative as it allows increasing the recovery rate, avoiding major penalizations due to the grade of the concentrate and increasing the added value of the final product. Leaching of scheelite by sodium carbonate presents several advantages such as its selectivity regarding the dissolution of troubling metals like iron and aluminium, allowing for a simple and flexible process diagram. However, it has the disadvantage that it is performed at high temperature and pressure with a high consumption of reagents. The feasibility of leaching is appraised by the extraction yield and selectivity, but also by the operating cost. Considering these aspects, a relevant objective of the research was to transform alkaline pressure leaching into a feasible processing alternative directly applicable to both medium- and high-grade ores and simultaneously to low- and high-grade concentrates produced by physical methods. The research used ore samples and low-grade concentrates from a typical skarn orebody as well as high-grade concentrates from a chalcopyrite-scheelite orebody. Different operating conditions were tested. Temperature, pressure and reagent concentration showed to be fundamental, but not exclusive, in determining the leaching behaviour. The operating conditions are milder than the ones generally proposed in the literature or currently in use in industry, but with higher carbonate consumptions. The research was oriented towards potential industrial implementation allowing for the application of optimization methods and straight scale-up to pilot-plan design and project.

By P. Perruzza, R. Grandori, A. De Biase, A. Ciamei, A. Busillo

The Turin metro alluvium soil is mainly made of large boulders, cobbles and gravel , few sand and almost no fines. This grain size curve is out of the range of application for EPB and Slurry TBMs. In order to bore 5 of the total 7,5 kms of Line 1 tunnel, two specially designed Lovat EPB TBMs were utilised in combination with a systematic non structural pre-grouting of a small volume rectangular slab just above the tunnel section. The same pre-grouting was not however applicable for lack of access on surface in some sections of the remaining 2,5 km of tunnel that had to be bored below important buildings/structures, with under ground water pressure up to 1,5 bar, with curves radius of 180 m only. For these more critical sections it was necessary to study and implement a new technical solution and improve the capacity of the TBM to work efficiently in EPB mode even in this unsuitable ground and overall conditions. After months of studies the selected and adopted solution has been to inject inside the cutterhead chamber, in addition to the almost standard foams & polymers additive mixes, a suspension of limestone powders. This with the scope of compensating the lack of fines of the natural ground with rock powders.

Jan 1, 2005

By M. Mead, J. Dumouchel, W. Yule, J. Giroux

The QMM mineral sands of South East Madagascar contain approximately 1,900 million tonnes of mineable sand with a total heavy mineral (THM) content of roughly 4.5wt%. The QMM deposits are the world’s largest known reserves of 60% TiO2 ilmenite and also contain a small volume of zircon. The deposits are semi-continuous and homogenous and the mineralized sands are free flowing with minimal overburden, induration & slimes. These characteristics are favourable to dredge mining and allow the application of conventional wet gravity, electrostatic & magnetic separation to final products. A mature THM mineral suite of high valuable heavy minerals (VHM) content has enabled the development of a relatively simple separation process.

Jan 1, 2005

By None None

Life as a mining/mineral professional doesn’t leave much time for perusing 20-page technical papers. Yet, being technologically savvy is part and parcel of a successful career in this industry. What’s an intelligent, well-informed person to do?

The schlieren technique describes an optical analysis method designed to enhance light distortions caused by air movement. The ability to visualize air flow has significant implications for analyzing underground mine ventilation systems, including the enhancement of surveys and models. Currently, traditional schlieren methods are impractical underground. Background oriented schlieren (BOS) provides a solution to this problem. BOS requires two primary components, a professional quality digital camera and a schlieren background. A schlieren background is composed of a varying contrast repetitive pattern, such as black and white stripes. This background allows the camera?s sensor to capture minor light diffractions, such as those caused by air flow. Although BOS shows great potential for ventilation analysis, sensitivity is an issue. This paper seeks to validate the BOS technique for imaging flow through a regulator by comparing BOS images with traditional schlieren images. This paper also outlines initial experimental efforts used for the validation.

Jan 1, 2011

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Steve Kral

MINExpo INTERNATIONL 2000 was a good place for companies to introduce new products, technologies and services to the mining industry. Caterpillar took that a step further. The company hosted a one-day preview of its mining products at its Tinaja Hills Training and Demonstration Center near Tucson, AZ. About 30 members of the trade press spent the day at Tinaja Hills before heading on to Las Vegas for MINExpo INTERNATIONAL 2000. Dozens of Caterpillar professionals provided the editors with a first-hand look at Caterpillar’s mining trucks, loaders, excavators, road graders, water trucks and engines. In addition, these Cat experts explained the intricacies of each piece of equipment, the latest technology that led their improvement and their value to the company’s mining customers.

Jan 1, 2000

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

By P. A. Plunkert, D. E. Morse, L. McCartan, S. F. Sibley

The average annual growth rate of real gross domes-tic product (GDP) from the third quarter of 2001through the second quarter of 2003 in the United States was about 2.6 percent. GDP growth rates in the third and fourth quarters of 2003 were about 8 percent and 4 percent, respectively. Many other indicators reflected a rebounding U.S. economy — rising consumer confidence, higher retail sales, greater industrial production and more housing starts. Inflation also reached a 38-year low in 2003. The upward trends in many sectors of the U.S. economy in 2003, however, were shared by few of the mineral materials industries. Annual output declined inmost non fuel mining and mineral processing industries, although there was an upward turn toward yearend as prices began to increase (Table 1).

Jan 1, 2004

By E. Sun

Tailings disposal is a significant consideration for the mining industry, with the majority of the ore processed in most mining operations ending up as tailings. Several tailings dam failure accidents have occurred during the past few years and mine tailings dam failures are occurring at relatively high rates. Tailings dam failure is disastrous with the serious damage and the loss of lives. To increase the tailings dam safety, a tailings dam monitoring and pre-alarm system (TDMPAS) based on the internet of things and cloud computing platform has been accomplished with the abilities of real-time monitoring of the saturated line, impounded water level, rain fall and the dam deformations etc. The TDMPAS has been applied in several mines in China and helped the mine engineers monitor the tailings dam safety and get warning information automatically and remotely in any kind of weather conditions. This work has been demonstrated the tailings dam monitoring and pre-alarm system (TDMPAS) is meaningful to monitor the tailings dam physical safety condition. The TDMPAS could be applied to monitor all the national tailings dams online in the future.

Jan 1, 2012