Search Documents

By F. Hassan, M. A. Arafa

At El-Gedida iron ore deposits there is a block of about 30million tons neglected due to its higher sulfur content due to the presence of barite gangue minerals. From this bluk by magnetic separation dual concentrates of high grade iron concentrate (~65%Fe and total Sulfur of 0.26%) and the second concentrate is barite of (60.87% BaO and total impurities of less than 3%).

Jan 1, 1999

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By Y. Nien Wang, Moe Amini, Heiner Sander, Max John

INTRODUCTION As the population increased along the coast route (California Route 1), and the people’s need to have guaranteed access increased, the landslides and related road closures began to have serious adverse economic impacts. Landslides were causing major long-term road closures about every 10 years on average. In 1983, ground movement at Devil’s Slide caused Highway 1 to be closed for an extended period of time which caused significant economic loss to the surrounding coastal communities. A number of options for bypassing the slide area were considered, and the Martini Creek inland bypass was selected for design. Subsequent litigation led to the creation of the Devil’s Slide Tunnel Study in 1996. The results of this study indicated that a tunnel alternative would be competitive with the inland bypass. The final decision was left to the citizens of San Mateo County, who approved the tunnel alternative in the November, 1996 election After completion of environmental studies and the processing of legal challenges, the final environmental document was finished in 2001. The preferred tunnel alternative was designated to proceed for final design and construction. PROJECT DESCRIPTION The Devil’s Slide Tunnels consists of a separated two-lane road, one lane in each direction, which passes through twin tunnels and over twin bridges and then connects with the existing non-separated, two-lane road at each end. The total length of the project is approximately 1900 meters consisting of four main project divisions, which are described below, going from south to north. 1.Operations and Maintenance Center (OMC) area, 2.Southern approach roadways to the South Portals (250 meters), including the South Rock Cut,

Jan 1, 2005

By Se-joon Kim, Jong-hwa Chun

"‘Gas hydrate’ is the common term for a solid material formed from the combination of various gases as ‘guest’ and water as ‘host’. A series of large-scale scientific drilling and coring programmes conducted since 2000 revealed that natural gas hydrate exists in a wide variety of accumulations in the sediments. The scaled-up onshore and offshore field production tests during the last decade show that gas production technology will be realized to make gas production from gas hydrates viable in the future, recognizing its potentials as one of the future sustainable energy resources.The total produced gas was approximately 470 m3 by the hot water circulation method over 6 days of operation in the permafrost-associated Mallik 2002 project in the Mackenzie Delta of Canada. In the Mallik 2007-2008 project, the gas was successfully produced stably by the depressurization method for 6 days, up to 13,000 m3 cumulatively. The depressurization method applied in the Mallik test was shown to be an effective way to produce gas from gas hydrates. The Alaska field trial to inject mixed gas of CO2 and N2 to exchange CH4 in 2012 was successfully done for the first time to produce maximum 1,270 m3 per day. A remarkable achievement was made by Japan when it completed its first offshore production test in the Eastern Nankai Trough, producing approximately 120,000 m3 of methane by the depressurization method over 6 days in March 2013. The technical challenges and scientific uncertainties obtained from Nankai Trough production test provide Korea with more considerations as to the aspects of well completion, reservoir formation and seafloor stability, sand control, flow assurance, environmental monitoring, and etc., due to the different geological setting and geomechanical properties of the Ulleung Basin in Korea."

Sep 1, 2014

By G. T. Adel, J. D. Miller, C. L. Lin

Washability analysis determines the maximum separation efficiency that can be achieved in the operation of coal preparation plants. Unfortunately, there are no on-line techniques for determining this most fundamental information. It now appears possible to determine coal washability on-line through the use of x-ray computed tomography (CT) analysis. This paper presents the results for the development of a CT-based, on-line coal washability analyzer. The development of appropriate hardware and software necessary to adapt a CT analyzer for use in determining coal washability is discussed. Testing of the analyzer using well-characterized coal samples is presented.

Jan 1, 2000

By Earl C. Herkenhoff

Editor's note: The subject of mining on the moon can generate a wide range of strongly held opinion, from those leaning toward the view that, ultimately, such activity is the destiny of mankind to those who believe that all suggestions for moon mining to date are unrealistic, wildly expensive and in the hands of people who 'know nothing.' MINING ENGINEERING herewith publishes some of the basic pros and cons on the subject of moon mining by writers who are among those holding strong views on the subject, with the hope that some of our readers may be interested in joining this debate. Every mineralogist and most mineral industry people were keenly interested in the examinations of the first moon rocks brought back by US astronauts in 1969. Suffice to say that the examinations revealed nothing exotic in the mineral makeup of the very limited rock samples. The rocks were generally of igneous type, dark-colored and contained some common, Earth-type minerals. There was, in Earth terms, above average TiO2 content, but they contained nothing of commercial significance by Earth standards. Therefore, interest in moon minerals rapidly faded. Years later, on Sunday, May 4, 1986, living in Reno, NV, this author was shocked to read a local newspaper article by the Dean of the Mackay School of Mines, University of Nevada, Reno, headlined, "Moon Mining Not Far Off." Considering that the announcement more or less coincided with a slump in our domestic mining industry, the immediate questions in a reader's mind

Jan 1, 1991

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

"Quang Ninh province is located in the north east of Vietnam and the coal mining in the province generates two thirds of the province’s GDP. The coal is extracted from both open pit and underground mines for the country’s complete coal export and by a share of more than 90% for domestic coal usage. Overburden generated through open pit mines is piled up nearby in the form of large waste rock dumps. The side-hill fill dumping near open pit mines is the source of environmental degradation in the region. Among the current problems at solid waste rock dump sites are dust emissions during and after dumping as well as Acid Rock Drainage (ARD). One of the major existing problems at waste rock dumps is dump stability (comprising erosion, sliding and subsidence issues). The RAME R&D project (Research Association Mining and Environment in Vietnam) is - among other activities - actively involved in the research for stabilisation and rehabilitation of mine waste rock dumps in Vietnam in the form of several sub-projects. The Institute of Mining Engineering I of RWTH Aachen University is leading the sub-project of mine waste dump stabilisation in co-operation with Chair of Geotechnical Engineering and Brenk Systemplanung GmbH. Mine waste dumping in the form of layers as an alternative to the side-hill fill dumping is expected to bring up environmental and economical benefits by minimising the problems of dump sites with the contribution to a sustainable development. Reduction of the post construction settlements, long term stable dump profile with minimum erosion, improvement of material parameters for geotechnical slope stability through compaction from hauling trucks as well as economical evaluation of new dumping concepts are the areas of the current research. The project has been financed by German Federal Ministry for Research and Education (BMBF). The ultimate aim of the sub-project is the compilation of the project results in the form of a "Best Practice Guide" and software based "Decision Support System" for planning and management of solid mine waste dumps."

Jan 1, 2011

By H. Sato, B. Thornton, K. Nishi, A. Usui

"Northwestern Pacific submarine seamounts are believed to be future marine mining areas of ferromanganese crusts, which contain hi-tech industrial metals, such as Co, Ni, Te, Ti, Pt, and REEs. The Takuyo No. 5 seamount is a member of the Cretaceous super-plume seamounts in the north Pacific, located within a Japanese EEZ (100 nm from the Minami- Torishima Is. or Marcus Is.), and only 300 nm away from the Japan’s Licensed area for exploration of Co-rich ferromanganese crusts under the ISA. This is an on-going program supported by independent academic communities but not a state-run program or managed by private funding.We have observed, sampled, measured, and analyzed the occurrences, distribution, physical properties, and microbiological environments at a selected flat topped seamount named Takuyo No.5 as a model area for scientific study of ferromanganese crusts within the Japanese EEZ. We then characterized crust structures, composition, age, and growth history, resulting in an understanding of the overall nature and distribution of these deposits from wide range of areas, water depths and geological environments. The study started with a ROV (Hyper-Dolphin 3K of JAMSTEC) exploration jointly with universities and national institutions (Japan Agency for Marine-Earth Science and Technology, Japan Oil, Gas, and Metal Exploration Corporation, and Geological Survey of Japan) in 2009 using marine geology vessels, remotely-operated vehicle, an oceanbottom drill machine, deep-tow TV camera, as well as conventional dredges and corers. We have been studying the topography, geology, nature of the bottom material of the seamounts using delicate sampling devices and measurement tools, and characterized the distribution patterns of the metal-rich ferromanganese deposits from chemical, mineralogical, and microbiological points of view."

Sep 1, 2014

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

By N. Dhawan

With ever-increasing demand, low-grade complex ores and strict environmental regulations, metallurgical processing options have become limited. Heap leach technology provides several benefits to combat these issues including low cost, flexibility and diversified process conditions. This paper provides an overview of heap leaching technology with specific emphasis on chemical aspects. Hence, influencing factors, advantages and disadvantages, testing approaches and some fundamentals will be discussed. Finally, heap leach technology for different ore types (copper, nickel, uranium and gold) will be briefly compared.

Jan 1, 2012

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By K. E. Livo, D. H. Knepper

Modern remote sensing provides a means for locating and characterizing exposed mineralized systems in many parts of the world. These capabilities are non-invasive and help target specific areas for more detailed exploration. An example of how remote sensing technology can be used is evident from a study of the Questa Mining District, New Mexico. Analysis of low spectral resolution data from the Landsat Thematic Mapper satellite system clearly shows the region-al distribution of two broad mineral groups often associated with mineralized systems: clay-carbonate-sulfate and iron oxides-iron hydroxides. Analysis of high spectral resolution data from the Airborne Visible and Infrared Imaging System (AVIRIS) shows the occurrence and distribution of many individual mineral species that characterize the pattern of hydrothermally altered rocks in the district.

Jan 1, 2004

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By Michael S. Kucker, Stuart Warren, Robert A. Robinson, Michael J. Lehnen, David McAllister

Geotechnical conditions exposed by the phased exploration programs have had a major impact on the selection of excavation and support methods, dewatering requirements, size of openings, vertical alignment, and estimated cost of construction for the Beacon Hill Tunnel and Station section of the “Link” Light Rail. Beacon Hill is comprised of a very complex glacial geology, including numerous slickensided fractures, injected sand dikes, and multiple perched groundwater levels as revealed by a phased boring program and exposed in a test shaft. The Geotechnical Baseline Report (GBR) presents this complex geology along with a “tool box” of alternative additional support systems to accommodate the varying ground conditions during construction of the station excavation. Additional explorations will also be accomplished during construction to further refine the geotechnical interpretations and provide an opportunity to use pro-active ground improvement techniques to optimize the station excavation and support requirements.

Jan 1, 2005

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By D. H. Horswill

The Red Dog Mine is the world’s largest zinc mine. It is located 145 km (90 miles) north of the Arctic Circle in northwest Alaska on lands owned by the Inupiat Eskimo organization called the Northwest Alaskan Native Association (NANA) Development Corp. NANA acquired surface and subsurface title to this resource as part of its settlement lands under the Alaska Native Claims Settlement Act. In 1982, NANA entered into a lease agreement with Cominco. Cominco is an international mining company focused on zinc. It built and operates the Red Dog Mine. NANA’s principle objective in the development of the mine was to have it contribute to the development of sustainable communities within their traditional region. This meant creating job opportunities in a modern economy while preserving the traditional subsistence lifestyles. Preservation of their culture, language and traditions are as important to the NANA people today as they were in the past.

Jan 1, 2000

By R. Owen

An overwhelming amount of data can be collected around the blasting process. This information can include blasting product, pattern design, blast results, and routing. It is only when these data sources are combined in a concise and accurate form that they are of real use in determining the safety and economic implications of each parameter. Two key technological aspects of blasting are drill fleet management (DFM) and size fraction analysis (SFA). As these technologies are integrated as near-real-time measurement and QA/QC tools, the resolution and realization of blasting parameters is significantly increased. The Freeport-McMoRan Morenci Mine has integrated these technologies along with other existing database structures to create a responsive and sustainable tool for reconciliation, forecasting and parameter matching. This ability allows Morenci to customize blast patterns to meet the criteria most critical to each shot, whether the impact is influenced by routing and recovery, equipment maintenance or safety concerns. DRILL FLEET MANAGEMENT The current DFM was stabilized in its current form in mid 2009 after database and hardware maintenance met stability requirements. Currently the system is running on 12 production drills. The system receives pattern layout and is capable of semi-autonomous drilling over the entire district. The fleet is capable of drilling in highly altered intrusive units and hard granites through the range of sedimentary and volcanic units that comprise the Morenci District. The system brings a level of accuracy not achievable with earlier paint-marked patterns. Depth control is also increased along with more consistent wear and maintenance patterns due to semi-autonomous drilling.

Jan 1, 2011