Search Documents

By Yongping Hu, Dianchen Cai, Congya Zhang

China is a rich in stromite mineral resource. Unfortunately, the resource is very difficult to separate by using conventional flotation method because stromite and gangue minerals are very fine disseminated, the average size of them is about 10 µm or below, and the content of clay minerals such as illite is 19% or even more. In this paper, the aggregation floatation behavior of ultrafine (-10 µm) stromite, illite, ablbite and quartz using anion collector were studied. The result show that, Oxidized paraffin (O.P) is a good collector and has better selectivity for stromite particles flotation. The salted sodium silicate depressed illite gangues minerals effectively. The separation of mineral mixtures was carried on successfully at one stage flotation by the technique. The mechanism of O.P. and salted sodium silicate were studied and discussed by using IR and Zeta- potential measurements.

Jan 1, 1995

By J. L. Hendrix, M. Ahmadiantehrani, G. Ramadorai

The concept of hypochlorite treatment prior to cyanidation in the heap leaching of low grade carbonaceous gold ores is discussed. Laboratory column leach tests using a low grade carbonaceous ore were performed to investigate the effects of pH, hypochlorite consumption and concentration, and bed height on total gold extraction. At high pH, hypochlorite stability increases and thus, hypochlorite consumption decreases. At room temperature, total gold extraction is proportional to hypochlorite consumption. However, at some point additional hypochlorite consumption does not increase gold extraction. Gold recoveries of 10% and 80% are achieved at 12 and 167 lb/ton hypochlorite consumption, respectively. Increasing hypochlorite concentration increases the rate of extraction. For a given hypochlorite consumption, gold extraction increased with decreasing ore bed height. Finally, using calcium hypochlorite results in higher gold extraction than using sodium hypochlorite at a fixed hypochlorite consumption.

Jan 1, 1992

By J. Herhold, S. Plaum

"Current and future operational processes in the mining and underground construction sector are under the influence of the prevalent competition and the acute necessity of optimization approaches concerning corporate and project processes. Besides general construction procedures, especially underground construction procedures and procedures in the field of deep shaft construction are high-profile. Those processes describe high technical challenges as well as increased requirements to occupational safety and health. Therefor an occupational safety management, which should be adjustable to the company itself and adaptable to all kinds of projects, shall be created. The creation of such an occupational safety management would lead to an economically optimized and safe (within the scope of OSH law) implementation of internal activities for the performance of construction services underground and in the field of deep shaft construction. With this approach the satisfaction of the high safety request as well as the demand for process optimization, as part of keeping the own competitiveness, will be satisfied successfully at once. PROJECT BACKGROUND Introduction The health and safety protection as well as occupational safety look back on a long historical development, which had brought more important sectors and developments during the last years, not only in Germany but also on the European and international level. The accident insurance protected by law has already been reported in 1884, which is astonishing early. The launch time point is strongly connected with the on-going economic development in the end of the 18th century, but above all this increased in the 19th century. The progress of occupational safety and especially the interest in the integration and the concentrated consideration of occupational safety and the health and safety protection in the company process is strongly visible during the 19th century and directly connected to the industrial revolution. [9] The industrial revolution and with that the development of work places lead to changing demands in the field occupational safety and health and safety protection. Insufficient security precautions caused problems in the industrial revolution, such as personnel and material losses as well as serious injuries and their consequences. These and the fundamental economic endeavours of the entrepreneurs lead therefore to the important step to develop an occupational safety system. [9] The prevailing basic ideas seize the insufficient security precaution of work places as well as the economical and profitable ideas of the entrepreneurs and bring them together. From this the necessary entrepreneur’s task comes into being and that is bringing the work conditions to the way that life and health of employees are not in danger. [9]"

Jan 1, 2017

By Michael J. Rinker, R. V. Nicholson

Waste rock and tailings from a proposed nickel-copper mine were evaluated extensively for potential on-land and under water disposal. Standard humidity cell and column tests were conducted over a two year period and underwater tests were conducted for more than one year. Nickel concentrations or release rates from the waste were consistent with nickel to sulphur ratios in the solids. This relationship provided a tool to assess the risk of metal leaching in wastes using nickel and sulphide assays. Nickel release and mobilization was found to occur for both oxidizing leach tests and under water tests even when pH values exceeded 7.0. Geochemical model calculations showed that iron oxyhydroxide solids can scavenge nickel from leachate and that the nickel inventory can be released from solids at relatively lower, but neutral pH values.

Jan 1, 2000

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999

By Suresh K. Bhatt

A mathematically simulated modeling technique is used in this U.S. Bureau of Mines paper to represent a hypothetical mining operation with existing mining technology and prevalent mining costs. Mining scenarios are prepared and evaluated for potential benefits and costs available through computer-assisted mining. Base criteria, parameters, and methodology are described.

Jan 1, 1991

By D. Spitty

Mining companies often have many disparate systems and repositories of data in their organization for planning and scheduling outbound mining supply chains. To optimize ore quality, throughput, transport logistics scheduling and delivery to contract, planning teams need to model and manage the value chain accurately and achieve a consolidated, enterprise view of operational performance. Planning teams coordinate a complex series of activities to ensure production forecast accuracy. They also negotiate and execute complex contracts often with disconnected and limited visibility of production forecasts, quality, and variability with little ability to accurately market potential product specifications over longer time horizons. This market is becoming increasingly dynamic, with increasing variability and the time for planning teams to react is decreasing. This is driving the need towards using science to generate the necessary scenarios required to support the decisions made by planners on a frequent basis. Resource-to-Market is a highly flexible, user-configurable supply chain management system for the mining and metal processing industries. This provides an integrated view of the supply chain that supports the dynamic nature of planning in a mining company, embraces variability of elements across the supply chain with the ability to optimize across all the functional areas of the operation to enable optimal decision making for often competing objectives such as throughput, quality, cost, revenue and profit.

Feb 23, 2014

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 2,903 t (3,200 st) of ore per day, with an average gold grade of 0.4 opt. The mine’s horizontal extent is large, 762 by 152 m (2,500 by 500 ft), while its vertical extent is 6 to 61 m (20 to 200 ft). A high density of joints occurs within the host rock. Based on rock mass rating and field observation, the ground conditions at Leeville can be characterized as poor to very poor. As such, heavy ground support is required for its mining operation. Ore zones with a height in excess of 10 m (35 ft) are considered for longhole stoping. A typical stope measures 6 m (20 ft) wide, 30 to 55 m (100 to 180 ft) long, depending on the ground conditions, and 10 to 30 m (35 to 100 ft) high, depending the thickness of the ore body, yielding 9,100 to 18,000 t (10,000 to 20,000 st) when completed. Narrow ore zones, less than 10 m (35 ft), are mined using cut and fill. Drifts at the Leeville Mine are 4.6 m (15 ft) wide by 4.6 m (15 ft) high. Because of poor ground conditions at this mine, the establishment of a ground control monitoring system is key to operating both safely and successfully. This monitoring system is composed of comprehensive instrument design and installation. Instruments include multi-point borehole extensometers (MPBX) and “stretch measurement to assess reinforcement tension” (SMART) cables. The monitoring system covers the mining zones and infrastructure openings. After about two years’ application and measurement, useful data has been collected and continues to be collected; this information will be used to design future stopes and infrastructure. The system makes engineering and operation teams able to do their job with more confidence and efficiency.

Jan 1, 2009

By W. P. Diamond

The Bureau of Mines has been investigating several techniques, including the use of horizontal and vertical boreholes, to remove gas from coal in advance of mining. Horizontal boreholes drilled from underground workings as part of the mining cycle have been shown (Finfinger, 1980; Hagwood, 1983; Perry, 1978; Prosser, 1981; Thakur, 1980; VonSchonfeldt, 1982) to be very effective in providing short-term, immediate relief from high methane emissions. This technique has been widely accepted in the coal mining industry, but it does require close coordination to integrate the drilling and subsequent gas drainage and disposal into the projected mine development plan. Vertical boreholes can be placed several years in advance of mining to predrain gas from coalbeds over relatively large areas (Dunn, 1984; Elder, 1975; Lambert, 1980; Steidl, 1978; Stubbs, 1979). The vertical borehole technique has the additional advantage over horizontal boreholes of allowing work to be performed on the surface instead of in the more restrictive underground environment. However, except for the relatively large scale vertical borehole programs for both mine safety and commercial production in the Black Warrior Basin of Alabama (Dunn, 1984; Lambert, 1980; Stubbs, 1979), the technique has been underutilized. The primary reason for this seems to be a combination of the current economic climate in the coal industry, legal questions as to the ownership of coalbed gas, and potential roof damage from the stimulation treatments required to increase the characteristically low permeability of coalbeds to enhance gas production. The question of potential roof damage is the subject of this paper.

Jan 1, 1985

By Rodolfo V. de la Cruz

The in-situ deformability of a highly jointed basalt rock mass was determined by two distinctly different methods: one, by the NX- borehole jack method where the displacements of opposing curved platens were related to the applied hydraulic pressures, and; two, by the modified Goodman jack method where the tangential strains on the borehole walls were related to the induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX- borehole jack method. To explain the discrepancy, the influence of fractures and test variables such as depth, orientation, hole number and applied pressure on the calculated modulus of the rock mass were analyzed by factorial analysis and it was found that the orientations and depths of measurement has statistically significant effects. The in-situ deformability values obtained by non-linear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1982

By R. O. Burt

The paper examines the role of gravity concentration in both an historical contest and within the modern mineral processing industry. It discusses the principles of the process on both a theoretical and practical level. The importance of ore mineralogy and its effect on the choice of the wide range of equipment available is discussed. The paper concludes with a discussion on the relative merits of gravity concentration to other forms of processing and seeks to answer the classical question - "Quo Vadis?"

Jan 1, 1982

By R. L. Pozzo

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying the Faraday's Law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a nonmagnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-electrode system involving pyrrhotite, pyrite and grinding media was also investigated as a first step towards elucidating the nature of interactions that occur in the grinding of complex sulfide ores.

Jan 1, 1987

By Rainer Antretter

The city of Garmisch-Partenkirchen in southern Germany is located at a main transit road to Tyrol in Austria and suffers of a very heavy traffic load. Therefore, the Kramertunnel as a by-pass tunnel is built to release/mitigate the traffic through the city centre. The 3,600 m long single tube road tunnel is designed with a parallel but smaller emergency tunnel and with cross passages, fitted with single- and doublesided emergency bays, a vent shaft, and an intermediate ceiling to separate fresh air supply from the road traffic. The tunnel, concrete lined along its entire length provided the challenge to find smart formwork solutions for quick set-up, repositioning, setup and pouring. Three particularly specific sections are discussed in this paper.

Jun 13, 2023

By P. R. Taylor

This investigation (Bowles, 1990) involves consideration of technology utilized by three separate fields of metallurgy and materials science: 1) The recovery of metals employing the use of solvent extraction, 2) The fabrication of materials using powder metallurgy, and 3) The use of composite materials in fabrication of engineering materials. The research considers each of the processes in order to realize the benefits of each. In light of the fact that materials have an intended use -it does seem plausible to simplify the process required between "mother earth" and final use. For instance, a primary copper producer that already employs a solvent extraction and electrowinning process could produce value added products directly. Part of the existing extractant flow could be diverted into a pressurized hydrogen stripping process in order to produce specialty composite powders. Innumerable methods have been employed for the recovery of metals; solvent extraction, the one considered in this study, was used due to the possibility of it providing a pure powdered metal. The use of solvent extraction in the recovery of metals has gained wide acceptance and its use proves beneficial in many applications (Ritchey and Ashbrook, 1984). Pressure hydrogen stripping of solvent extractants may provide the benefit of flowsheet simplification compared to conventional solvent extraction followed by electrowinning. It may also provide the benefit of direct production of high purity metal powder (Demopoulos and Distin, 1985).

Jan 1, 1992

By J. F. Oyler

One of the most important applications of material handling engineering technology occurs in iron ore pelletizing plants. Although the total installed value of material handling systems in such plants, as well as in many other modern process plants, is a relatively small percentage of the value of the plants (5 to 10% perhaps), their significance is considerable. Indeed this significance equals that of the more expensive process equipment in the plant, since the failure of any component of any system causes, shutdown of the entire plant. It is because of this increased consequence of failure that design criteria for process plants are more conservative than for conventional material handling applications. A second unique characteristic of material handling technology applied to process plants in general is the variety of materials being handled and the wide range of problems this variety presents. One extreme encountered is the stickiness of filter cake. Here the entire design effort is aimed at keeping the material flowing through transfer points and preventing it from building up on components. Another extreme is the conveying of fired pellets - hard spheres with a very flat angle of repose and abrasive characteristics severe enough to make conventional wear plate materials impractical.

Jan 1, 1976

By D. R. Nagaraj

Depression of copper sulfides followed by MoS2 flotation is the most commonly practiced technique for Cu-MO separation. Although numerous organic depressants have been developed in the past, a majority of the currently used copper depressants are inorganic compounds (ex. NaHS, Nokes reagent, etc.). A unique advantage of organic depressants over the inorganic compounds is the potential versatility for design of the organic molecule to suit many requirements. The present study was initiated to systematically investigate the structure- activity relationships for a large number of organic complexing agents in comparison with the commonly used inorganic depressants that are often inefficient and hazardous. The results obtained in this study are discussed in light of the useful correlation obtained between practical solution redox potential and depressant activity. Several requirements, such as the presence of an active -SH and hydrophilic -OH or -COOH in the organic molecule, are identified for a reagent to be a satisfactory depressant. Some preliminary results on the desorbability (or destruction) of collector coating on the sulfide surfaces in the non-xanthate collector systems are also discussed.

Jan 1, 1983

By J. L. Vanderbeek

Investigations have been conducted at Chino Mines Company into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on the laboratory, pilot, and plant scales, to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 34% with a reduction in specific energy (kWh/ton) of 33%. Test results obtained to date are presented.

Jan 1, 1985

By C. Alexander

Stillwater Mining Company is developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in south central Montana. A 5650 meter (18,550-foot) tunnel is required to gain access to the ore bearing horizon (J-M Reef). Access and primary mine development can be accelerated through the use of two 4.6 meter (15-foot) diameter tunnel boring machines (TBM). One TBM was purchased new while the other was purchased used. Machine specifications, site support facilities, portal/launch chamber construction, TBM assembly, startup and operation are discussed in this paper.

Jan 1, 1999

By Neil J. Dahmen, Howard J. Handewith

INTRODUCTION Tunneling machines were introduced into civil con¬struction in the 1800s, but their practical applications were not realized fully until the 1950s. As of 1977, tunneling machines were being used on most tunneling projects of substantial size. As in civil construction, the mining applications of tunneling machines have included long drives such as tunneling for long ore-body develop¬ment drifts, long haulage tunnels, longwall access drifts, and long crosscut developments. Tunneling machines ranging from 1.75-m (5.7-ft) to more than I1.0-m (36-ft) diam are available from several manufacturers; machines for mining applications generally have ranged between 1.75 and 6.0-m (5.7¬and 20.0-ft) diam. Tunneling machines usually operate at or near horizontal grades and are supported by a rail-haulage backup system. However, declines and inclines have been made using alternative backup equip¬ment. Either circular or shaped tunnels may be bored, depending upon the particular equipment used. Using tunneling machines to bore openings through rock offers several advantages over the use of the drilling and blasting technique. These advantages include a rapid advance, continuous operation, uniformity of the opening size, smooth walls, and safe working conditions. Compared to drilling and blasting, boring reduces the disturbance of adjacent rock, thereby reducing the ground-support requirements and the exposure to water inflows. The smooth walls provide natural arching and present minimum resistance to the flow of air. A tunneling machine should be considered a spe¬cialized mining tool that is well-suited to certain mining applications. Properly applied and sustained, a tunnel¬ing machine contributes to realizing substantial econo¬mies in the development of underground mines. All costs herein are expressed in 1977 US dollars, unless otherwise noted. The mention of trade names and manufacturers is not intended to imply an endorse¬ment of any specific equipment. TYPES OF TUNNELING MACHINES As listed in Table 1, five principal types of tunneling machines were being manufactured in 1977. Each type of machine offers a special solution to a specific mining problem. Although each of these types of machines is described herein, most of this chapter is devoted to the full-face rotary rock-tunneling machine that has demon¬strated the greatest production in both civil construction and mining applications. Full-Face Rotary Rock-Tunneling Machines As shown in Fig. 1, a full-face rotary rock-tunneling machine consists of a rotating head that is fitted with rock-cutting tools and is forced into the tunnel face. This head is supported by a bearing on a structural support member that, in turn, is held in place by a hydraulically positioned wall-gripping mechanism. Both torque and thrust are reacted from the cutterhead, through the structural support and gripper mechanism, and to the tunnel wall. The rock cuttings fall to the invert at the tunnel face, and they are removed by means of cutterhead buckets or scoops that transfer the cuttings to a conveyor belt. After advancing the cutter¬head through a preset boring stroke, the tunneling machine is advanced by hydraulically pulling the gripper mechanism in from the tunnel walls, stroking forward, and resetting the gripper to the new forward position on the wall; the machine then is set for the next advance stroke. Full-face machines cut only circular openings. Ma¬chines with diameters as small as 1.8 m (6 ft) and as large as 6.1 m (20 ft) have been used in mining applica¬tions, excavating rock with unconfined compressive strengths in excess of 276 000 kPa (40,000 psi). Although special machines have been designed to turn on a radius of 30 m (100 ft) in both horizontal and vertical directions, the conveyors and backup sup¬port equipment generally limit tunneling machines to turns with a radius of more than 60 m (200 ft). The full-face rotary rock-tunneling machines have provided the fastest and most reliable production of any mining method or machine. These machines can be equipped to place any of a variety of ground-support systems, and they can be provided as "open" machines, as shown in Fig. 1, or as "shielded" machines, as shown in Fig. 2. The open machines have the advantage of allowing the ground to be supported as near to the tunnel face as possible. The shielded machines have been designed principally to allow placing precast con¬crete segments. The shielded machines completely pro¬tect the equipment and personnel at the heading, but they are economically limited to permanent long-life haulageways where full lining is required. Partial-Face Rotary Rock-Tunneling Machines As shown in Fig. 3, the partial-face rotary tunneling machine is equipped with a cutterhead that rotates slowly at about 0.21 rad/s (2.0 rpm). The single-disk cutterhead produces the tunnel section shown in Fig. 4 by means of an oscillating motion. These machines work on the undercutting principle, and they are avail¬able in spring-line dimensional increments of 0.1 m (0.32 ft) from 1.5 to 2.1 m (5.0 to 7.0 ft); the vertical dimensions are 2.4 to 3.2 m (8.0 to 10.5 ft), respec¬tively. Depending upon the tunnel width, the cutterhead disk may be fitted with from 8 to 16 drag-bit cutters. Penetration is achieved by means of hydraulic rams that force the tungsten-carbide bits into the rock mass. The operation is cyclic, with cutting occurring only on the upstroke. On the downstroke, the rotating cutter¬head draws the fallen muck from the invert into the panzer-type conveyor for rearward transfer. This feature allows time to either reposition ore cars or to exit the tunnel with muck trains while the machine is cutting, as shown in Fig. 5. Boom-Type Rotary Excavators The boom-type rotary-excavator tunneling machines commonly are known as boom-type continuous miners

Jan 1, 1982

By Tetsuo Yamazaki

Natural cold seepages are characterized as rapid upward transports of methane from deeper parts of geological structures to the seafloor. Thermogenic and/or biogenic methane generated in deep sediments moves up to seafloor, and major part of methane is consumed in anaerobic oxidation of methane (AOM) and hydrogen sulfide is created in anaerobic sulfate reduction by consortium of microorganisms. Then the hydrogen sulfide is utilized by chemosynthetic communities near the seafloor, such as Acharax, Calyptogena, Bathymodiolus, and the mat-forming bacteria Beggiatoa (Fig. 1). When the supply of methane is large or rapid, remaining methane escapes from seafloor, and it is aerobically oxidized in seawater. A mass balance ecosystem model of chemosynthetic community around natural cold seepages in sediment layer and on seafloor has been created and improved by the authors (Yamazaki et al., 2005; Takeuchi et al., 2007). The model is constructed from 3 main processes as schematically shown in Fig. 2: (1) Methane supply process; (2) Ecosystem process; (3) Water column process. The part of chemosynthetic communities is in the ecosystem process. A numerical model CANDI (Carbon And Nutrient Diagenesis) was developed by Boudreau (1996) to simulate the biogeochemical processes such as organic matter, oxidant, nutrient, bi-product, and pH diagenesis in aquatic surface sediments. Then, the improved version named C. CANDI was developed (Luff and Wallmann, 2003; Luff et al., 2004). The authors created the same type carbon and nutrient diagenesis process model with calcium carbonate formation like C. CANDI (Yamazaki et al., 2005), and have added the sulfur oxidizing and immobilization processes (Takeuchi et al., 2007). The sulfur oxidizing and immobilization processes are connected with the carbon and nutrient diagenesis process model.

Jan 1, 2008