Search Documents

By Donald Bishko

Zoning is the legal means by which land use can be controlled. Although zoning laws have historically been quick to prevent quarrying, one is hard pressed to find zoning ordinances which specifically state that land should be used (or held in reserve) for quarrying and prevent other uses such as recreation, housing, etc. This situation is especially true when the mineral to be quarried has a low intrinsic value such as sand, gravel, and crushed stone. The chance of a gold mine surviving urban sprawl is probably considerably greater than that of a sand and gravel pit, even though it is possible that the dollar value of the sand and gravel' would exceed that of the gold mine. The research reported herein was concerned with two major topics: to delineate the real costs associated with the non-protection of our construction aggregate resources (growth minerals) and to develop a computer simulation model which would aid planners in making economically sound decisions. This paper describes the problems faced by the mineral aggregate industry and discusses the role of computer simulation in planning problems. It briefly describes a simulation model which has been developed and previously reported12 and discusses the results of a pilot study conducted on the Tri-City area (Albany, Schenectady, and Troy, New York). 3

Jan 1, 1970

By A. Bhagavatula, M. Rezaee, M. J. Kiser, R. Q. Honaker

"A field study of the coal preparation plant fleet in the eastern United States was undertaken to determine if quantify of rare earth elements (REEs) present in the product streams are large enough to justify further concentration. Representative composite samples were taken from the clean product, coarse refuse, and fine refuse streams from 20 coal preparation plants. Each stream was then separated into various size and density classes and analyzed for ash and REE contents. The large database showed that coarse refuse contained the largest amount of REEs, although the ratio of heavy to light REEs was greater for the clean coal products. The concentration of REEs was also compared to that typically seen in the earth’s crust. This enrichment ratio ranged from approximately 1.5 to more than 4.0 as the ash content varied. The database also showed that a linear correlation existed between La and Ce for many REEs of interest, although there were several notable exceptions for some of the high-value REEs. INTRODUCTION Worldwide energy demand is expected to grow by as much as 37% by 2040 according to the International Energy Agency (2014). This growth, coupled with a decrease of the reliance on coal to generate energy, means that it is more important than ever for countries to secure the materials necessary to meet its energy projections. For the United States, the U.S. Energy Information Administration (EIA) predicts that total domestic electricity use will increase roughly 25%, from 3,836x109 kWh in 2013 to 4,797x109 kWh in 2040 (EIA, 2015). In the EIA’s reference case, coal’s contribution to electricity generation drops from 39% in 2013 to 34% in 2040. On the other hand, renewables share of electricity generation grows from 13% to 18% for the reference case. Compared to its current state, renewable energy electricity production is predicted to grow as little as 50% to as much as 121% over this time period, depending on the economic case being examined. This growth will largely be seen in the wind and solar sectors (EIA, 2015). The focus on viable renewable energy resources will be crucial to the future of fueling American growth. Many of the renewable energy technologies, such as wind turbines and photovoltaic films, rely on materials and supply chains outside of the United States. The lack of a reliable and low-cost domestic supply could pose a threat to the growth of the renewable energy markets in the United States. This potential vulnerability recently led the United States Department of Energy (DOE) to create a Critical Materials Strategy Report. In this report, 15 elements were identified as critical for the continued growth of the renewable energy market. Eight of these elements were rare earth elements (REEs). Five REEs (dysprosium, neodymium, terbium, yttrium and europium) were identified as highly critical and vulnerable to shortages (Bauer et al., 2012)."

Jan 1, 2016

By Francisco A. Fonseca

The Carajás Hills are in Brazil's Eastern Amazon, between the Araguaia and Xingu rivers, and parallels 5° and 7° Latitude South. A location map is given in Fig. 1. It is an area of low mountains (maximum altitude 900 meters), covered by the Amazon rain forest. Annual average temperature is 25°C, ranging from 31°C (maximum) to 19°C (minimum). Annual rainfall averages 2,000mm. Although it rains throughout the whole year, heavy rains occur from December through March. At the beginning of the 20's, Brazilian explorationists made brief geological descriptions of the area. Due to the thick soil, scarce fresh rock outcrops and the tropical forest covering a completely unpopulated area, detailed geological studies were difficult and reconnaissance expeditions were limited to the river margins.

Jan 1, 1982

By Robert N. Morris

Ladies and Gentlemen: It is a distinct pleasure and honor to appear before you representing the railway industry as I do, but there is a much closer personal relationship. I am a graduate Mining Engineer and worked in the coal industry for 15 years prior to becoming a railroader only 4 ½ years ago. I have been a member of AIME most of my adult working life and am currently active in the Washington, D. C. Section. While having been in the railway industry only a short time, I have become involved during the recent period of innovation and development of the new railroad technique known as unit train service. I have had the privilege of helping to work out a number of unit train movements to both electric utility companies and to a major steel concern, handling coal from mines on the Southern Railway to the consuming plants. On Southern, our unit trains are all of what I shall describe as shuttle train operations whereas within the railroad industry today several types of service are characterized as unit train service and many don't offer comparable efficiencies.

Jan 1, 1968

By B. J. Timmons

An initial point that I would like to make very emphatically?and as our title might erroneously suggest for those of you old enough to remember . . . Peter Harben and myself do not intend to shoot ourselves in the foot. We derive our livelihood from a number of aggregate, industrial and other minerals producers, both here in the United States and outside. This paper, therefore, is a fence-straddler or for information purposes (we hope) only, rather than any "fur or agin" stances. In essence, some of you may consider it a U.S.G.S. publication! In fact, we hope that it serves to inspire aggregates producers to do some radical thinking, to promote introspection, and to that end it would benefit both domestic and foreign producers. The title could be shortened into a brief question of "Aggregates Travel?" with an emphatic no for the answer. In the past, the success of a construction materials venture depended upon your ability, through siting, to provide the customer f.o.b. the job site, a product at the lowest possible cost.

Jan 1, 1987

By D. N. Madge

A survey is given of production scheduling systems currently in use or contemplated for future use in Cominco operations. Emphasis in this presentation is made on the chain of decisions that are made with the help of mathematical programming models. Some attention is devoted to the structural properties of the models.

Jan 1, 1966

By J. J. Sammarco

Computer-aided control of a mining machine pl aces its operator in a safe, remote location, thus reducing health and safety risks, Sensing systems that provide machine position (xy coordinate) and heading (yaw), are extremely useful in aiding remote positioning of mining machines. The U. S. Bureau of Mines has developed two sensing systems for position and heading information: A scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system that employs ring-laser gyroscopes. This paper presents a brief background and status of these sensing systems as applied to the remote positioning tasks of a continuous mining machine. Included are field test results of each system operating in a room-and-pillar research section at a cooperating mine in West Virginia.

Jan 1, 1992

By J. S. Chen

DOE recently funded 21 projects under the solicitation by its Environmental Restoration and Waste Management Division. This project is combining the expertise of an interdisciplinary team of researchers with that of three manufacturers to isolate nuclear waste storage sites using remote longwall mining. The concept is being pursued in Germany, too. This paper will present the conceptual approach to the project and discuss the problems in transferring longwall mining technology to nuclear waste containment.

Jan 1, 1994

By B. Zane Egan

The Calsinter process for recovery from fly ash involves sintering the fly ash with calcium sulfate and calcium carbonate at 1200°C, followed by a dilute sulfuric acid leach step. Flue gas desulfurization sludge containing calcium sulfite, calcium sulfate, and unreacted calcium carbonate may be substituted for the calcium sulfate and calcium carbonate. Conversion of aluminum in fly ash by the sintering process to an acid-leachable species was measured as a function of sintering time and temperature in the range of 800°-1200°C The sinter-leach steps were investigated using thermogravimetric analysis, x-ray diffraction, scanning electron microscopy, and elemental analysis. SEM photographs indicated that the glassy spheroids in the original fly ash were converted to a crystalline structure by the sintering reaction.

Jan 1, 1980

By A. Torrance, M. G. Seo

Velocity of detonation (VOD) is an important variable when evaluating the performance of mine blasts. Typically, for a VOD measurement, individual probes have to be loaded into each blast hole that requires a measurement, which increases the loading time and is not representative of the whole blast. Experimental studies of electromagnetic pulse (EMP) from the detonation of explosive charges show that electric and magnetic field signals are observed when chemical explosions occur in the air, at the ground surface, and in the underground. EMP has the potential to evaluate VOD of the whole blast without impeding the loading process. Due to a variety of physical causes which make the electromagnetic effects complex, measuring EMP of the detonation of explosive charges has not been fully studied yet. Five different antennae were tested with explosives, which are commonly used in mining industry. Among the five antennae, aluminum and copper tape, and wire were successful to detect the EMP. INTRODUCTION The measurement of the velocity of detonation (VOD) helps in evaluating and comparing relative performance of explosives in mine blasts. A VOD of an explosive is usually predicted by empirical mathematical equations or measured in-hole by VOD meters. However, conventional methods to measure a VOD have constraints: only a limited number of holes can be measured because cost of consumables for such systems is very high, and systems only allow a certain number of holes to be measured. The measurement cables have to be placed into the holes prior to loading with explosives which means that preparing to take the measurement is time consuming and has to be well coordinated with the mine. In order to evaluate VOD for a whole blast, there is a possibility of using electromagnetic pulse (EMP) from the detonation of the explosives. As there are many parameters that affect the generated EMP from explosive charges, measuring EMP of the detonation of explosive charges has not been fully studied yet. Most studies conducted relate to military related explosives, not the ones frequently used in mining industry. This research has been performed to have a better understanding of EMP from the types of explosives which are commonly used in the mining industry. To discover a way to detect EMP efficiently, five different types of antennae have been studied in the air and in the underground blasting conditions: coil, monopole rod, log periodic, wire, and aluminum and copper tape. LITERATURE REVIEW Conventional methods of measuring VOD Over the years, demands for more accurate theoretical predictions and physical measurements of the effects of the explosives have increased. Especially when both demand and commodity price decline, mining companies are keen to understand the effectiveness of explosives since it has a direct relationship with fragmentation, which influences their production rate. Since the 1940s, various methods have been devised to determine VOD of explosives.

Jan 1, 2019

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By Gregor de Ratmiroff

Field prospecting for bauxite in Venezuela has had a long but interrupted history having till now oferred but evidence of occurrences. The Venezuelan Government, trough the Corporación Venezolana de Guayana (C.V.G.), in 1974, formalized a major effort in prospection for bauxite in the Shield area and the Orinoco Delta in orden to establish the possibility of raw material supply to an upcoming and expanding aluminium industry. The Corporation, in turn, created and delegated to the Division of Geological Stu- dies, the formulation of the necessary infrastructure and execution of work in orden to determine the existence of economically exploitable bauxite deposits.

Jan 1, 1979

By Benjamin Grunauer, Anthony Iannacchione, Taylor DaCanal

"In Pennsylvania’s rich mining history, various forms of room-and-pillar mining have been in use for over 150 years. Longwall mining, introduced in the late 1960s, occupies only the last 60 of those 150 years and now represents the dominant method of extracting coal in the Pittsburgh coalbed. The introduction of longwall mining allowed larger quantities of coal to be extracted in safer and more efficient manners than room-and-pillar mining. However, the associated formation of subsidence basins have elevated both the number and intensity of watersource and surface structure impacts. When these first longwall panels were mined the factors responsible for these impacts were poorly understood and regulations were focused only on surface structures. Today, with over 600 panels mined under a wide range of conditions, these factors are known and regulations have developed to help mitigate water supply and surface structure impacts.The cause and severity of surface effects are thought to be dependent on multiple factors, including the location within the subsidence basin, overburden, panel width, and orientation of the panel. The changing characteristics of over 600 longwall panels mined in the last 60 years are analyzed to determine factors important in subsidence related surface impacts. This study compares the location of the surface impacts with the longwall panel size, overburden, and maximum predicted vertical subsidence. The data shows that changing these characteristics are impacting surface features in a significant manner as measured by the number of company liable reported effects.INTRODUCTIONLongwall mining has occurred in Pennsylvania for over 60 years, and at the current mining rates, longwall mining is expected to continue in the Pennsylvania Pittsburgh Coalbed until the reserves are exhausted. Figure 1 shows all mining that has occurred in the Pittsburgh Coalbed, as well as the area that is left to mine. It is predicted that there are 40 years left of longwall mining on the Pittsburgh Coalbed, under the assumption that 50% of the total 280,000 acres will be mined at the current rate of 3500 acres/year."

Jan 1, 2019

By C. G. Anderson

The treatment of materials for the recovery of the precious metals imposes many processing and environmental challenges. Sunshine Mining and Refining Company has developed hydrometallurgical technology for recovery of values from refractory precious metal materials. At Sunshine, the industrial focus of these processes has been for the direct recovery of silver without cyanidation. However, recent work has indicated that these technologies can provide a means for treating complex, refractory gold concentrates. This will be the focus of this paper. The practice of pretreating ores and concentrates to make them more amenable to cyanidation is becoming more common. Several pretreatment options for sulfide concentrates containing gold include roasting, bio-leaching, direct pressure oxidation and nitrogen species catalyzed pressure oxidation. The industrial use of nitrogen species catalyzed pressure oxidation has been limited to the Sunshine refinery where its focus has been for the treatment of silver concentrates. Much of the reluctance, outside of Sunshine, to use this type of technology may be based on the perception that high costs are associated with using nitrogen species (e.g. nitric acid, sodium nitrite) to leach. Also, the use of nitrogen species catalyzed pressure oxidation on an industrial scale is unfamiliar to most metallurgical professionals. A summary of pressure leaching processes which utilize nitrogen species as a catalyst is presented in Tables 1 and 2.

Jan 1, 1996

By Ronald H. Mullennex

The growing need for development of thinner, more erratic, or less easily- mined coals in the Appalachian region requires more detailed analysis of conditions and factors controlling or influencing deposition of these seams. The value of depositional modelling in evaluation of such coals has been demonstrated in many recent studies and publications. Such modelling may be applied to allow prediction of factors varying from regional coal occurrence trends to very local areas of seam discontinuities, but requires thorough utilization of all available types of data. Mapping of general depositional energies, as derived from basic geophysical and driller&apos;s logs, can be applied to specific prediction of coal occurrence, and projection of particular facies as representative of unique depositional features or conditions often proves more applicable to coal character delineation than does mapping of the coal itself. Depositional modelling and trend projection may also serve as a guideline in reserve classification and confidence-levels in reserve estimations.

Jan 1, 1981

By M. Canty

Results are presented that were gathered during pilot-and field-scale testing of an innovative technology, sulfate-reducing bacteria (SRB), designed to treat and control acid mine drainage (AMD). The project was performed under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy through an Interagency Agreement. The MWTP is implemented by MSE, Technology Applications, Inc., located in Butte, Montana. Sulfate-reducing bacteria, a common group of anaerobic bacteria, produce hydrogen sulfide and bicarbonate when supplied with sources of carbon and sulfate. Hydrogen sulfide reacts with metal ions in AMD, precipitating them as metal sulfides; the bicarbonate serves to help neutralized the drainage. Pilot-scale testing was performed within eight packed-bed reactors at a temperature representative of a field application of this technology in a northern climate, nominally 8°C. The reactors, packed with an organic substrate, were operated continuously in upflow configurations receiving AMD at a flow rate corresponding to a 5-day retention time over a test duration of 60 days. During this time, numerous physical and chemical parameters were monitored. Pilot-scale metal removal efficiencies reached 99% for zinc, 99% for aluminum, 96% for manganese, 98% for cadmium, and 96% for copper. Iron and arsenic removal was not as effective as the aforementioned metals, which was largely attributed to the high levels of iron and arsenic contaminating the organic substrate. Evidence existed that both adsorption and sulfate reduction were occurring within the reactors.

Jan 1, 1998

By L. B. Rothfeld

This paper presents preliminary results of a Bureau of Mines study of potential costs of compliance with the federal Resource Conservation and Recovery Act for copper heap and dump leaching. Specifically, estimates are given for the cost of compliance with possible technology standards that would require the use of liners and closure caps regardless of terrain and underlying geology and hydrology. This cost is compared to the co lit of compliance with present state requirements for terrain a typical of those found at existing copper leach sites in the Southwestern U.S.A. Incremental compliance costs are found to widely exceed screening criteria used by the Environmental Protection Agency to denote significant economic impact.

Jan 1, 1993

By M. G. Hester

The inadequacy of traditional geostatistical methods for estimating some precious metals deposits has become apparent in the last few years. New methods or estimation such as Indicator, Probability and Multigaussian Kriging are difficult to understand and apply. Case studies using a new method of variogram calculation proposed by Srivastava show the method valuable for variogram estimation in precious metal deposits. Some simple, sometimes unorthodox. estimation methods that have proved useful in Some situations are presented.

Jan 1, 1990

By C. Newman, R. C. Ray

Originated and developed in the civil tunneling industry, the Ground Reaction Curve (GRC) has provided a robust methodology for evaluating and designing ground support in both tunnels and underground mining scenarios. This paper presents a preliminary assessment in the utilization of the GRC concept for the evaluation and design of the pillar-support system with respect to overburden stress and displacement. This initial assessment will be based on and backed by past research on this topic. Underground mine instrumentation is planned for a longwall mine in the Appalachian coal field based on the research and findings in this paper to support the postulated hypothesis. INTRODUCTION Since the early 1970’s, the mining industry has evaluated the structural stability of a pillar by dividing an approximated pillar load by an approximated pillar strength. While this design methodology has served the industry well in the past, as modern mining operations continue to develop in more complex geological and geometric conditions coupled with market economics, industry professionals are in dire need of a modified stability assessment approach which considers both the stress condition and material displacements. Within the civil tunneling industry, the GRC approach has been successfully utilized in designing underground support measures that enhance the stability of an underground excavation. Through the incorporation of current industry knowledge and understanding of ground and support behaviors this paper looks to investigate into preliminary assessment for the development of a Modified Support Response Method (MSRM) to further improve the analysis of local and global underground stability. CURRENT PILLAR DESIGN METHODS AND THEIR LIMITATIONS Globally, multiple pillar design methods have been utilized in the design of underground excavations. Each of these methods approaches the calculation of pillar stability a little differently with respect to material properties, underground geometries and stress conditions. Analytical solutions can be used to determine the strength of homogeneous materials like concrete, but not in case of non-homogeneous and non-isotropic mineral deposits in a mine. These equations are often derived using empirical methods. Pillar strength is defined as the maximum resistance of a pillar to axial loading (Brady & Brown, 1985). The strength of mine pillars is typically estimated through indirect methods. In the past, researchers have correlated the strength of a given size and width of a rock specimen to the strength of a mine pillar. The first study on the effect of geometry on rock strength was done by (Bauschiger, 1876) on Swiss sandstone samples. Since then several empirical equations to determine pillar strength had been published by many researchers like (Bunting, 1911), (Griffith & Conner, 1912), (Greenwald, Howarth, & Hartmann, 1939), (Holland & Gaddy, 1957), (Evana, Pomeroy, & Berenbaum, 1961) and (Holland C. , 1964).

Jan 1, 2019

By R. D. Hansen, R. R. Klimpel

Previous papers by these authors on slurry rheology control grinding aids have emphasized the end-use results and application methodology involved. This paper emphasizes the chemical principles and the influence of various chemical structures behind slurry rheology control chemicals. Particular examples are shown which correlate chemical structure modifications to environmental factors involved in grinding such as pH, shear, ore type, water chemistry, and particle size.

Jan 1, 1990