Search Documents

By N. L. Parduhn

Populations of Bacillus cereus spores are elevated in soils over four subsurface gold deposits in the western United States. Large deposit-to-background ratios of B. cereus populations were obtained in soil traverses over the Minnesota vein deposit, Empire District, Colorado (maximum 50:1); the Shasta (maximum 3,500:1), and Evening Star maximum 18,000:1) vein deposits, Shasta County, California; and the Hog Ranch disseminated gold deposit (maximum 40,000:1) in Washoe County, Nevada. Small increases in the concentration of toxic metals in the soil may be responsible for the elevated spore populations. The observed elevation of B. cereus spore populations near these gold deposits indicates that the method should be further investigated as a potential exploration tool.

Jan 1, 2013

By Maurice L. Madden

An investigation was undertaken for a ground water discharge plan for the Chino mining complex near Hurley, New Mexico. Operations which impact ground water include dump leaching, storage reservoirs, and tailings seepage. The investigation included both hydrogeological data collection and laboratory analysis. A conceptual understanding of surface water and ground water was then developed. Surface water and ground water models were used to match existing conditions and predict the impact of operational modifications. The study concluded that runoff and resulting leach reservoir overflows were primarily responsible for the ground water degradation. Tailings seepage represents a smaller part of the impact.

Jan 1, 1984

By C. Salcedo, J. Vallance, J. Sáez, M. Robles, J. Spangenberg, S. Rosas, L. Fontboté

The Tambomachay ore deposit (13°28'36.78"S, 71°57'35.98"W, about 6 km north of the town of Cuzco, Peru) consists of Cu hosted in arkosic red beds of the Kayra Formation (Lower Eocene). Bornite, chalcopyrite, chalcocite, covelite, digenite, malachite, and chrysocolla occur disseminated in thin layers and in veinlets. The occurrence of the copper ores in a part of the red bed sequence containing green reducing layers, the presence of organic matter in interstices between the hypogene sulfides, and the sulfur composition of the copper sulfides (δ34S values between -16.9 and -12.4‰ vs VCDT) pointing to bacterial sulfate reduction, are strong arguments to propose that mineralization was caused by copper-bearing oxidizing saline basinal fluids that precipitate copper sulfides when they meet reduced sulfur in an organic matter-rich horizon. Faults parallel to the regional Tambomachay Fault could have acted as feeders for oxidizing basinal copper-bearing fluids. Fluid migration was probably driven by tectonically-induced topography gradient. INTRODUCTION A number of red bed Cu occurrences are known in the Cuzco region in the early Eocene – early Oligocene San Jerónimo Group (Gregory, 1916; Carlotto et al., 1996, 2011; Loza et al., 2004). In the past, copper ores were extracted in several small-scale mines in the surroundings of Cuzco, including Tambomachay, Tipón, and Zurite in the Cusco province and Ushpa, Guilda, Giovanna, and Langui in the Sicuani Province. The abandoned Tambomachay Mine (13°28'36.78"S, 71°57'35.98"W), about 6 km to the north of the town of Cuzco (Romero et al., 2015; Salcedo et al., 2017, Fig. 1) was chosen as the main site for the present research aimed to better study the genesis of these copper occurrences. Results deriving from fieldwork, microscopic characterization of ore and host rock, and sulfur isotope determination suggest that the key factor for the genesis of the copper ores is that copper transported by oxidizing basinal fluids is trapped by reduced sulfur of bacteriogenic origin located in a part of the red bed sequence that shows intercalatins of green reduced horizons.

Jan 1, 2019

By J. A. Boyle

In the Frick District of U, So Steel Corporation, we have had more than 37 years of experience in the use of multiple-fan ventilation systems, in our coal mines. In our Colonial field, with a long belt installation, we have mined 85 million tons of coal with the use of the multiple fan system of ventilation. In our Palmer field, with the use of the same arrangement, we have mined 90 million tons of coal--a total of 175 million tons without one accident attributable to improper mine ventilation. The same system, fundamentally, has been installed in our expanding Robena operations and at its present stage of development we are using eight fans to ventilate this area. To date we have mined 55 million tons of coal with very encouraging results and again without any accidents attributable to ventilation.

Jan 1, 1961

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with mediumsized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in the present study: a 15.2-cm (6-in.)-wide shelf; a 7.6-cm (3-in.)-wide shelf; and a 7.6-cm (3-in.)-wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1 and 1:1 were evaluated for the 15.2-cm (6-in.)-wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. IntroductionSurface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1 percent of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples).• 5.8 percent of rotary drillers were overexposed to respirable silica dust (nine out of 155 samples).• 7.3 percent of drill helpers were overexposed to respirable silica dust (three out of 41 samples).• 7.5 percent of blasters/shotfirers were overexposed to respirable silica dust (three out of 40 samples)."

Jan 5, 2018

By R. W. Ballmer

Bingham Canyon lies in the heart of the Oquirrh Mountains, 25 miles southwest of Salt Lake City, Utah. In it is located the world's largest open-pit copper mine, owned and operated by the Utah Copper Division of Kennecott Copper Corporation. From the beginning of open pit mining operations in 1906 until 1963, the pit haulage, or materials transportation, was primarily by rail. In 1963, phase-in of a truck haulage system in the upper two-thirds of the pit was begun. The details of that conversion, its associated problems and the resulting pit operation have been covered in an earlier paper.1 The purpose of this paper is to discuss various factors for consideration in transportation system selection, and to discuss some of the alternatives considered prior to making the change from rail haulage to truck haulage for a portion of Bingham Canyon.

Jan 1, 1968

By D. C. White

The Vulture Mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11,000 kg Au and 8,000 kg Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely disseminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence all dipping north about 35°. Early mining focused on the vein-hosted gold particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pitting of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry.

Jan 1, 1988

By Danforth R. Hale

The pressure of military use of quartz resonators led to efforts to Grow high, grade quartz crystals in Germany and in Great Britain during 19)3-25, and was responsible for a series of U.S.A. Signal Corps contracts beginning in 1946 with the Clevite Corporation (as the former Brush Development Company), Bell Telephone Laboratories, Antich College, and others. The technique of growing crystals from the melt, such as KI, NaBr, was already commercially inuse Quartz could not be so grown, since its utility depends on the form stable below 573°C, and, even if it could be grown from an extraordinarily viscous melt, the higher form passing through this transition becomes twinned. Again, several crystals were being grown commercially from water solutions; quartz, however, is listed in the common literature as being insoluble in water. Fused quartz, or vitreous silica, was chosen as raw mater¬ial by the European experimenters because of its thermodynamically lesser stability than quartz, and various alkaline solutions were tried for the purpose of enhancing the solubility.

Jan 1, 1964

By Kenneth Savidge

With the recent demand for increased coal production there has been a corresponding increase in the horsepower of the shearing machines. The resultant increase in the machine haulage pull has heightened the incident of haulage chain breakage resulting in machine downtime, but more seriously the danger to face personnel. This paper discusses the application of chainless haulage to longwall mining and describes the systems currently available.

Jan 1, 1978

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global platetectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20o in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed

Jan 1, 1999

By Henry N. McCarl

[ ]

Jan 1, 1966

By S. K. M. Chao

The increasing demand for large volumes of relatively low-cost cement has resulted in the need for an equally low-cost high-volume means for transporting that cement. It has been estimated that 20% - 25% of the total cost of cement to the buyer represents delivery expenses from the mills. For instance, during the 1972 cement shortage in the Southeastern region of the U. S., bid prices for a ton of cement delivered increased to $45 compared to $20 average at mill price, i. e. , F. O. B. plant. Much of the increase was caused by the anticipated higher cement shipping costs for longer hauling distance. The exceptionally high bid price, of course, was not the price quoted by the successful bidder. Thus, clearly, cement is not a marketable commodity unless it can be economically transported to the consumer.

Jan 1, 1975

By Harvey P. Knudsen

This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima Nine, located near Tucson, Arizona. Results at the Pima Mine indicate that the geostatistical method is no better nor worse in predicting block grades and total tonnage than the ELIP or IDS methods in contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELlP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties, the geostatistical model is more attractive, due to its ability to construct confidence limits on the estimates.

Jan 1, 1976

By W. Dan Hausel

In previous reports by Hausel et. al., (1979 a, b, and c), Leighton and McCallum (1979), and McCallum (1974;1979), several exploration procedures were examined as to their effectiveness in locating kimberlite intrusives in northern Colorado and southeastern Wyoming, where approximately 90 kimberlites have been recognized within 5 districts (Figure I). Briefly, geological mapping and stream sediment sampling for indic- ative heavy minerals of kimberlite (pyrope garnet, chrome diopside, and magnesian ilmenite) proved to be the two most effective methods in isolating kimberlite occurrences within the granitic terrain of Colorado and Wyoming (Hausel et. al., 1979 a, b, and c; Leighton and McCallum, 1979). Where a kimberlite intrusive is deeply weathered, remote sensing using color and color infrared aerial photography may be a potential reconnaissance tool in kimberlite exploration. The kimberlitic eluvium supports thicker grassy vegetation, and at least one species of grass (the Bluebunch Wheatgrass) is found to grow only within the eluvium. The result is that vegetation in the kimberlitic eluvium is a better infrared reflector than the vegetation in the surrounding granitic soils (Hausel et. al., 1979 b; McCallum, 1974

Jan 1, 1980

By N. Mehrshad

Research and experience have demonstrated that the operating conditions of the flotation process are reflected in the froth?s appearance. Despite recent advances in image analysis and several algorithms developed for froth flotation, there still is not a comprehensive algorithm to accurately determine bubble features from actual froth images. Being able to accurately and automatically measure bubble size distribution is an important requirement for optimization and control of the flotation process. Segmentation is one of the most effective approaches for accurately determining the bubble size distribution. In the present study, a new bubble segmentation algorithm, which utilizes an adaptive marker-based watershed transform, is proposed to measure the bubble size distribution from froth images. The developed algorithm is validated using some industrial scale froth images from flotation cells at different duties.

Jan 1, 2011

By Floyd L. Prestridge

A test of a solvent extraction (SX) pilot plant featuring electrostatic coalescence has been performed by C-E Natco at the United Nuclear uranium mill in Church Rock, New Mexico. Operating in parallel with the United Nuclear SX system, the C-E Natco electrostatic SX pilot plant exhibited comparable extraction efficiency to the United Nuclear system which utilizes conventional mixer-settlers. The C-E Natco pilot, however, operated at much higher liquid loading rates and exhibited less communication between the aqueous phases of the extraction and stripping circuits.

Jan 1, 1983

By R. L. Keaton

Since the earliest days of mining, the job of digging coal out of the earth has been considered one of the world?s most dangerous occupations. From 1880 to 1910, mine explosions and other accidents claimed thousands of victims. In 1907 alone, over three thousand deaths occurred in U.S. coal mines. Public concern has prompted the passage of much needed safety legislation; from the creation of the U.S. Bureau of Mines in 1910, to the comprehensive laws of the Federal Mine Safety and Health Act of 1977. This type of legislation, along with the cooperation of industry, labor, and MSHA has contributed greatly in making mining safer and more healthful. Mining deaths and injuries have declined Significantly since those early days. However, even though this trend is positive, none of US can afford to look at the injury numbers and frequency rates and label them as acceptable.

Jan 1, 1988

By William H. Engelleitner

Agglomeration by balling in cylindrical or shallow pan devices dates back to the early part of this century. The first sintering tests conducted by Dwight-Lloyd on nonferrous ores included a mixing step for ore, flux and fuel carried out in a deep pan device similar to the balling pans, or discs, presently in use. Further work directed mainly toward sintering of ferrous and nonferrous ores always included a preparatory step, usually referred to as mixing, agglomerating or green-balling of the ingredients. In the late forties and early fifties two methods of particle preparation prior to firing were in general use. In Europe the balling pan was used predominantly, both as a mixer and as a pelletizer. In the United States many pilot plants and semi¬commercial plants used balling drums. When the first iron ore pelletizing plants were built in this country, the most frequently used device for green-balling was the cylindrical drum. At the same time, the pan device was used both in Europe and the United States for many other materials such as fertilizer, cement, flyash, alumina and copper concentrates, as well as to mix the feed for sinter machines. The difference between these two balling devices - -the drum and the disc - has been the subject of much discussion and is well covered by several papers included in the 1962 publication "Agglomeration' issued by AIMS, based on their 1961 International Symposium held in Philadelphia. (1)

Jan 1, 1965

By M. R. Rosen

CARBINDER Polymer 498 is a liquid organic taconite binder which significantly improves fired compression in both fluxed and acid pellets. It has been used commercially in both shaft and straight grate furnaces. This new binder produces an unusual wicking phenomenon during balling wherein the rate of movement of interstitial water is accelerated to the surface of the balls. The phenomenon is proposed to be responsible for the significant improvement seen in fired compression. This paper presents information as to the effect of CARBINDER Polymer 498 on green ball and fired pellet properties. It also describes the wicking phenomenon and discusses a reversal in the normal balling operation procedures required for successful agglomeration.

Jan 1, 1988

By S. B. Patton

A comprehensive approach to the development and organization of an expert system that is designed to assist electricians in diagnosing electrical faults m mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures m the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchical structure an: formulated by creating "what-if" scenarios and performing a qualitative circuit analysis for each fault Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide' reference material and tutorials on the circuit are also described.

Jan 1, 1989