Search Documents

By Yiming Sun, John Stolz, Jakob Walter, Drew Mason

The Courthouse Commons SEM Tunnel was excavated within 6 feet of cover beneath two buildings in downtown San Diego utilizing high-precision geotechnical instrumentation. The excavated dimensions are approximately 25 feet in diameter and 328 feet in length connecting two in-service detentionlevel security buildings. Presupport includes large-diameter grouted canopy pipes and smaller pipe spiles. Initial support consists of fiber-reinforced shotcrete with lattice girders. This paper presents observed ground and structure behavior and lessons learned. During construction an unanticipated brick structure was encountered, and methods were developed to improve adhesion of shotcrete to sandy soil and to reduce rebound

Dec 1, 2022

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By John Callahan

A stream sediment (minus 80-mesh and minus 60-mesh panned concentrates) and lithogeochdcal survey for gold did not locate any Triassic-age placer deposits in the northern Wadesboro and southern Sanford basins in North Carolina. A stream sediment geochemical program for uranium funded by the North Carolina Energy Institute did identify one and anomalous site (8.5 ppm U; 5 ppm Th) near Covenington, North Carolina and eighteen possibly anomalous sites (1-1.6 ppm U) . Five of the eighteen samples with uranium levels in the 1-1.6 ppm range have high thorium levels (112-853 ppm) and may indicate a monazite source for the uranium. Gold values as high as .83 ppm in the stream sediments and 9.3 ppm in the panned concentrates were obtained during the survey. Small (<.5mm) flattened grains of gold (1-4 grains) were observed along with coarse kyanite and/or monazite in some of the panned concentrates. A distinctive pattern of high gold values in the sediments was observed in the vicinity of Mangum, N. C. where Minard (13) reported values as high as 2.1 ppm £ram a Triassic lithology. Follow-up gold analyses on over 400 rock samples from twenty-eight exposures near Mangum failed to obtain any high values (<55 ppb). The presence of coarse kyanite, monazite and gold in panned concentrates may be from a source younger than the Triassic lithologies that the streams currently drain or adjacent Paleozoic rocks.

Jan 1, 1979

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov&apos;s original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973

By J. C. Norman

The United States was the world&apos;s largest producer and consumer of boron compounds during 1994. According to US Bureau of Mines (USBM) estimates, boron mineral concentrate and chemical production in the United States totaled about 1.05 Mt (1.15 million st), yielding 560 kt (617,000 st) of B203, for a total estimated value of $370 million. This production level was about 2% less than 1993 revised figures. The United States continued to provide nearly all of its own boron supply while maintaining a strong position as a source of sodium borate products and boric acid for export. Domestic employment in the mining and beneficiation of boron products during 1994 was 900 people, about the same as in 1993. USBM estimated total world production of boron of about 2.3 Mt (2.5 million st), yielding 1.1 Mt (1.2 million st) of B203. World production during 1994 was about the same as during 1993. USBM estimates US reserves to be about 210 Mt (231 million st) of ore and world reserves to be about 630 Mt (694 million st) of ore.

Jan 1, 1995

By Michael V. Wolski, Ryan O. McCarter, Kenneth A. Johnson

"The Central Subway is Phase 2 of the San Francisco Municipal Transportation Agency’s (SFMTA) Third Street Light Rail project and will extend the existing Phase 1 initial operating segment from its current connection to the Embarcadero line at Fourth and King streets along Fourth Street to Market Street, under the Bay Area Rapid Transit (BART) and Muni Metro tunnels and then north beneath Stockton Street to Chinatown (Fig. 1).Total new track to be constructed as part of the Phase 2 work consists of approximately 734 m (2,410 ft) of surface track and 2,636 m (8,650 ft) of tunnels. The tunnels were constructed as twin, singletrack bores by two tunnel boring machines (TBMs) (Johnson, 2014) moving north from the southern end of the launch box under the I 80 freeway between Bryant and Harrison streets. North of Chinatown Station the TBMs continued another approximately 683 m (2,240 ft) to a retrieval shaft near Columbus Ave. at Washington Square. The project also includes five cross passages to connect the two tunnels, and three underground stations (the Yerba Buena/ Moscone Station, Union Square/Market Street Station and Chinatown Station.)Excavation of the twin tunnels was performed with two TBMs, with both TBMs driving northward from the launch box. TBM excavation was performed such that the location of the machines was staggered to separate the active excavation faces by a minimum of 91 m (300 ft) between headings. This minimum separation was maintained until the first TBM arrived at the retrieval shaft plug, at which time the separation requirement was relaxed.Excavation began with the “southbound” (SB) tunnel which will ultimately accommodate the southbound TBM light rail trains followed by the second TBM in the “northbound” (NB) tunnel. With the completion of the drives in June 2014, cross passage excavation then began and was completed in April 2015. Overall, construction of the Central Subway tunnels was a success considering the nature and complexity of the project. Additional details of the completion of the Central Subway tunnels are presented in another paper from the RETC 2015 conference (Leong et al., 2015)."

Jan 1, 2015

By A. Gene Collins

The demand for lithium may increase because of its potential use id lithium batteries and in the generation of electrical power by fusion. Therefore, lithium abundance in some United States oil-field brines was surveyed. Oil-field brines from numerous locations were found to contain more than 100 mg/l lithium and several exceeded 500 mg/l. An area of 25,000 km2, with a reservoir thickness of 60 m, an effective porosity of 5 percent, and a brine with a specific gravity of 1.2 containing 100 mg/l of lithium, contains about 0.75 x 106 tonnes (1 tonne = 1 metric ton = 1,000 kg) of lithium in 7.5 km3 of brine. It is postulated that the brines were enriched in lithium by lithium-rich spring water or lithium leached from volcanic rocks followed by evaporation sequences.

Jan 1, 1978

By James C. Norman

The boron review arrived too late to appear in the June issue. The US was the world&apos;s second largest producer and the largest consumer of boron compounds during 1990. Boron mineral concentrate and chemical production in the US totaled 1.13 Mt (1.2 million st), including 565 kt (662,800 st) of boric oxide (B2O3) in 1990, according to US Bureau of Mines estimates. Total value amounted to $404 million. This was slightly higher in production than 1989 but down in value, reflecting a softening in boron product prices. Total world production of boron mineral concentrate and chemical tonnage in 1990 was estimated at 3 Mt (3.3 million st), which corresponds to about 1.3 Mt (1.3 million st) of BO,. World production in 1990 was about the same as in 1989.

Jan 1, 1991

By Michael H. Leon, John A. Organiscak

Controlling worker dust exposure on longwall mining systems is difficult because the working face area serves as an immediate return during the mining cycle and the amount of airborne dust generated is directly related to production. Since improvements in longwall mining technology have significantly boosted production levels, additional technology is needed to control the airborne respirable dust generated at present and future production levels. One concept to reduce longwall worker&apos;s dust exposure is to maintain two splits of air at the face -- a clean intake split in the workers walkway, and a return (dusty) split over the face conveyor. The U. S. Bureau of Mines has recently investigated a concept to overcome the visibility handicap of face partitions by utilizing a permeable polyester mesh. The mesh material was anticipated to provide adequate air-splitting capabilities as long as the pressure differential between the face and worker walkway was minimal. Initial testing of this concept at the Bureau&apos;s Lake Lynn Laboratory showed that notable reductions could be achieved with a 1/8 in (3.18 mm) and 1/16 in (1.59 mm) mesh opening size. Dust reductions at 100 ft (30.5 m) and 200 ft (61.0 m) downstream of source were 58 and 36 pct, respectively, for the 1/8 in mesh and 79 and 55 pct, respectively for the 1/16 in mesh. Longwall application of the 1/8 in mesh showed similar results to the Lake Lynn Laboratory tests. A flame retardant mesh was used underground with portable lighting mounted on the shearing machine for face side lighting.

Jan 1, 1993

By Pedro D. Lasota

Chile leads the world in copper production with an annual capacity nearing 2 Mt (2.2 million st). Most of the country’s copper production, about 74%, is mined by open-pit mining methods. Open-pit mining also accounts for a major portion of Chile’s production of other commodities, including iron, gold, silver and coal (Table 1). Chile’s mining boom began 10 years ago and is expected to continue through the end of the decade. From 1980 to 1990, copper production in Chile increased 48.7%. During the same period, gold production increased 303%, silver production increased 119% and coal and iron ore production increased 163.7% and 6.6%, respectively (Table 2). It is estimated that copper production will be in the order of 2.3 Mt (2.5 million st) by 1996, when new projects now under construction come onstream. Gold production could reach 35 t (1.1 million oz) and coal production could increase another 1 Mt/a (1.1 million stpy). Open-pit mining has played a significant role in Chile’s minerals production growth. The expected increases in mine operations will come about mainly through new open pits or expansions of existing surface operations (Table 3). However, the number of open-pit copper mines will decrease from 74% to 66% of the total number of Chilean mines. Gold mines will increase from 63% to 69% of the total, while coal mines will go from 41% to 59%. Most all of the present iron ore production is from surface mines and will continue that way.

Jan 1, 1992

By C. T. Thompson

"Rotary percussion" implies two types of energy, rotary and percussion. Into these categories fall rock&apos; drills of varying sizes. The larger ones drill above 6" diameter holes; the medium size, 2 3/4" to 4 1/2" holes; and the smallest, 1 1/4" to 2" holes. Essentially, the larger holes are drilled with doom-the-hole drills using tri-cone bits. Percussion energy evolves from the drill piston and rotation power from the rotary table or overhead drive, using drill collars or pull down mechanism to preload the bit.

Jan 1, 1963

By J. C. Monette

Stripping of gold and silver from carbon is effected by means of two main processes (AARL and ZADRA ). The main rate-enhancing parameter in the stripping of gold and silver is temperature. A secondary rate-enhancing parameter is ionic strength. (1) Stripping is usually conducted within a solution containing sodium cyanide (0.1 -0.5% ) and caustic ( 1 -3%). The development of a chemistry that increases the rate of gold and silver stripping from carbon in a manner proportional to its concentration is described. Its use in atmospheric and pressure strips is also outlined.

Jan 1, 1992

By Antonieta Middea, Rupen Adamian, Fernando F. Lins

This work presents the results obtained with aggregation of fine talc (-19 m), a naturally hydrophobic mineral, in the presence of KC1 solutions. The classical DLVO theory describes well the aggregation of talc in dilute KC1 solutions. Beyond 1 M KCI we have found indications that a non-DLVO interparticles force is operative, say an hydration (repulsive) force. This structural force could be responsible for the unexpected re-dispersion of talc suspension. However, no repulsive force (depression) has been observed in salt flotation of talc at higher ionic strength, up to 3 MKCI.

Jan 1, 1995

By D. D. Harbuck, G. K. Green

The Bokan Mountain area on Prince of Wales Island, AK, contains vast quantities of heavy rare earth minerals. To lessen the US dependence on foreign sources, the US Bureau of Mines (USBM) investigated yttrium recovery from this ore. By sulfating the ore at 250 ° C for 1 hr at an H2S04:ore ratio of 1:1 and then water leaching the sulfated material for 1 hr at 20% solids and 25ºC, over 74% of the yttrium, cerium, and lanthanum were solubilized. Solvent extraction (SX), using a synergistic combination of OPAP and DEHPA, selectively loaded 100% of the yttrium. Yttrium was stripped directly as a solid using a 2M, 35 ° C NaOH liquor. When the OPAP/DEHPA mixture was tested in a continuous SX circuit, yttrium loading and stripping were 100% and 96%, respectively. The organic showed excellent recyclability properties with minimal solvent loss.

Jan 1, 1996

By Daniel Hodouin, Claude Bazin, Sami Makni

SCOTT COULTER: Thanks, Eric. Thank you all for coming. Our first speaker today is Claude Bazin. Claude received a degree in metallurgical engineering in 1980 from Laval University in Quebec. He worked for a short time in a mineral processing plant and then returned to Laval to complete graduate studies in the field of process modeling and control. He obtained his master&apos;s degree in 1983 and his Ph.D. in 1990. In 1987 he joined Brunswick Mining, New Brunswick, as research metallurgist and subsequently process control engineer. In 1990 he joined Helzfield Mines, New Brunswick, as senior metallurgist. In 1991 he accepted a position of professor at the department of mining and metallurgy at Laval University, a position he is still holding. He&apos;s a member of the CIM, TMS, and the Society for Mining, Metallurgy, and Exploration. Claude&apos;s topic today is "On-Line Material Balance for Flotation Plants." INTRODUCTION CLAUDE BAZIN: During the last two decades, the on-stream analyzer (OSA) has gained the stat& of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant (Leroux and Franklin 1994), and its application to oxide mineral flotation plants is increasing. The OSA assays are sent to the flotation operators via an operator console or to control loops of various degrees of complexity (McKee 1991) implemented in a distributed control system (DCS). Operators and/or controllers take control actions based on these assays to ensure an adequate operation of the plant. Although this application pays off very rapidly for the purchase of the OSA, one could ask, "Could we get more from the OSA?" Some plants reported the use of OSA measurements for process optimization (McKee 1991). The optimization strategy is based upon economic indices calculated from metal recovery using the 2-product formula (Wills 1992, p. 124). The 2-product formula is sensitive to measurement errors in the assays and can lead to considerable scatter in the calculated indices (Hodouin et al. 1993). Least squares algorithms provide a robust alternative to filter out measurement errors (Spring 1992). This paper presents some applications of a recursive least squares algorithm that provides real-time estimates of the mass flow rates within a flotation plant using OSA and mass flow rate measurements.

Jan 1, 1998

By Harry M. Castrantas, James L. Manganaro, Craig W. Rautiola, James Carmichael

Caro's acid (peroxymonosulfuric acid) was successfully field tested as a cyanide detoxification agent at a North American gold mine. An on-site FMC generator injected Caro's acid into a mill tailings slurry sump. The WAD cN-(weakly acid dissociable plus free cN-) was reduced from 40-108 ppm to below the target level of 20 ppm using a 1/1 mole ratio of CA (Caro's acid) /CN-. At an inlet CA/CN-mole ratio of 1.8/1, WAD CN­concentrations as low as 4 ppm cN-were achieved. Raw material costs for the cyanide detoxification were cut by 60% compared to using hydrogen peroxide (H202) alone. Detoxification time with Caro's acid was much faster compared to H202. This resulted in completion of detoxification before the treated slurry reached the tailings pond thereby substantially reducing the probability of wildlife fatalities.

Jan 1, 1993

By F. Heivilin

"Health and Safety problems can make a mineral deposit or a portion of one, an operating plant, or finished product unprofitable or worthless. Therefore they need to be reviewed when reserves are established and yearly thereafter until the deposit is closed down. Health and Safety regulations serve as a guide, but I have always done more frequent checks, when adding new products with different specifications or during times of bad weather and crisis. Water quality and quantity are always in question. Health and Safety are quality of life issues which are at or near the top of priorities for communities, companies, employees, and government bodies. Georgia dropped from one to three in U. S. for business development due to “Quality of Life” issues. Remember crystalline silica is present in nearly all sedimentary and acidic rocks and basic igneous rocks are the perceived home of asbestos. These health issues, any other safety and health issues or perceived issues need to be resolved initially and any time they come up during life of deposit. When handled properly good safety and health programs add to the profitability of a deposit, not to the costs. Daily safety checks in operating plants and mines, and visual check of all drilling core with an eye for changes are a key to successful programs. Both plants I turned around had terrible safety records, too much airborne dust, and maintenance problems resulting in low productivity. In almost every case cost reduction was tied to eliminating maintenance and spillage problems which caused health problems and increased possibility of accidents. Implementation of these safety and health programs around 1970 starting prior to government programs, working with new MSA/MSHA regulations, working to improve the regulations as a president of a state mining organization, and maintain profits was a challenge, but very rewarding. Reducing time to make repairs and work simplification gleaned from observations and employee recommendations learned from making multiple daily inspections resulted in years without lost time accidents at two plants, reduced maintenance and 33-75 % improvement in cost per ton at A. P. Green Refractories Co. Eufaula Calcining Plant 1972-77 and Oil-Dri Ochlocknee plant and mine 1979-82. The Ochlocknee mine worked 1981-2007 without a LTA. The author participated in 16 acquisitions and new plant design projects. All of above reduced costs allowed mining deposits with higher overburden to be used and considered. Thereby increasing reserves considered in all operations."

Jan 1, 2016

The Mining Foundation of the Southwest (MFSW), located in Tucson, AZ, will hold its 16th annual American Mining Hall of Fame Awards Banquet Saturday, Dec. 5,1998. The Hall of Fame recognizes outstanding contributions to the mining industry by selected individuals and industry partners. Each year, one living award recipient and up to two mining history honorees are chosen by the , Hall of Fame Committee and the Board of Governors of the Mining Foundation. In 1989, the Mining Foundation initiated a Medal of Merit to recognize outstanding individual, technical and professional contributions to the mineral industry. In 1995, an award was created to recognize contributions made by companies and organizations in partnership with the mining industry. This year&apos;s inductee, guest of honor and featured speaker will be Charles G. Preble, president and chief executive officer of Southern Peru Copper Corp. He is being recognized for outstanding performance as an executive of an American company operating under difficult circumstances in a foreign country. The Hall of Fame will induct H. Myles Jacob, former chairman and CEO of Inspiration Copper Co., for innovation and farsightedness in matters pivotal to the cop- per industry of his time. In addition, John Cromwell Lincoln, former president and chairman of Bagdad Mining Co., will be inducted for his outstanding contributions to the American mining industry. These contributions include metallurgical research and development of the Bagdad Mine as well as pioneering innovation in the electrical industry. Medals of Merit will be awarded to David N. Skillings, editor and publisher of Skillings Mining Re- view, for his dedication and support of mining interests. J. Ruben Velasco Rodriguez will also receive a Medal of Merit. He is economic geologist, professor and former secretary of the board of directors and secretary general of Compania Minera de Cananea. His medal is for fostering excellent relations between Mexico and the , United States in mining geology and management and for advancing the professional development of others in the field of earth science. An Industry Partnership Award will be presented to Stephen Bechtel and the Bechtel Corp. in recognition of Bechtel&apos;s 100th anniversary and the company&apos;s outstanding service to the mining industry. The banquet will be held at the The Westin LaPaloma in Tucson beginning with cocktails at 6:30 p.m. Tickets are available from Clare A. Roscoe, manager, Mining Foundation of the Southwest 520-577-7519, fax 520-577-7073.

Jan 1, 1998

By Robert Blair, David L. Fey, Stanley E. Church

Determination of the pre-mining geochemical baseline in bed sediments in watersheds impacted by historical mining activity is important in establishing watershed restoration goals. We have developed methods to solve this problem in the Animas River watershed, southwestern Colorado, using geomorphologic mapping to identify terraces that contain pre-mining sediments. Following a systematic evaluation of possible sites, we collected samples of pre-mining sediments in gravel deposits from 21 sites throughout the watershed. Geochemical analysis of individual layers has produced a chemical stratigraphy that can be tied to the historical record through geochronological and dendochronological studies. Analysis of geochemical data, when coupled with the historical record, clearly shows that there has been a major impact on the geochemistry in bed sediments in the active stream channel by past mining activities. Historical mining has resulted in a substantial increase in metals in the very fine sand to clay-sized component of the bed sediment of the upper Animas River, and Cement and Mineral Creeks, which are the major tributaries of the Animas River. Enrichment factors for metals in modem bed sediments, relative to the pre-mining sediments, range from 1 to 6 for arsenic, 1 to more than 10 for cadmium, 1 to about 15 for copper, 1 to more than 25 for lead, 1 to more than 10 for silver, and 1.6 to more than 12 for zinc. The pre-mining bed sediment geochemical baseline is high relative to average crustal abundance values of many metals. The Animas River watershed above Silverton, Colorado would be readily identified as a highly mineralized area suitable for mineral exploration if it were not disturbed by mining.

Jan 1, 2000

By Osamu Nishikokura, Jumpei Yamashita, Darrell Liebno, Malcolm Sheehan

"The Eglinton-Scarborough Crosstown Project builds a 19km LRT corridor that includes a 10km underground portion, between Keele Street and Laird Drive. The West Tunnel Contract (ECLC1-15) includes 6.5km of twin EPB TBM bored tunnels with a 5.75m internal diameter precast concrete segment lining (PCTL), between Keele Street and Yonge Street. This paper summarizes the overall scope of work, the technical challenges faced and innovative solutions developed by the contractor during the TBM move across an existing subway tunnel using state of the art high capacity strandjack gantry crane.1. PROJECT OVERVIEW The Greater Toronto and Hamilton Area (GTHA) is Canada’s largest urban region, populated with over 6 million people, and is one of the most rapidly growing regions in North America. One forecast estimates that the population of this region will increase to 8.6 million by the year 2031. In September 2008, Metrolinx, an agency of the Government of Ontario, launched a 25-year regional transportation plan named “The Big Move” to cope with the expected increase in transportation demand. The Eglinton-Scarborough Crosstown, one of the projects included in “The Big Move”, is a light rail transit (LRT) that will run across Toronto in an east-west direction between Mount Dennis and Kennedy along Eglinton Avenue. In October 2012, the West Tunnel Contract of the Crosstown LRT (ECLC1-15) was awarded to Crosstown Transit Constructors (CTC), a joint venture between Obayashi Canada Ltd., Kenny Construction Company, Kenaidan Contracting Ltd. and Technicore Underground Inc. The project includes approximately 6.2 km long twin bored tunnels, 9 cross passages, 1 emergency exit building, 7 sets of station headwalls, and an intermediate pair of extraction and launch shafts. Each of 6.5 km long twin tunnels are divided by the existing subway station into two drives: the first half from the launch shaft LS-1 (west of Keele Station) to the extraction shaft ES-1 (west of Eglinton West Station), and the second half from the launch shaft LS-2 (east of Eglinton West Station) to Yonge Station, as shown in Figure-1. The TBMs are extracted at ES-1 and moved to LS-2 over the existing Yonge-University Subway Line at Eglinton West Station before resumption of tunneling at LS-2."

Jan 1, 2016