Search Documents

By Hisakazu Matsushita, Yoshio Yamaguchi

INTRODUCTION Shinkansen, operating 1,176km between Tokyo and Hakata, transports 340,000 passengers a day. Presently, the 466km Tohoku Shinkansen linking Tokyo and Morioka and the 270km Jyoetsu Shinkansen linking Omiya and Niigata are under construction. It is progressing smoothly and 95% of the civil and architectural construction has already been completed.

Jan 1, 1981

By J. Lovering, H. Wilhelm, P. Siewert

Introduction The Afton property is located 290 km (180 miles) by air east-northeast from Vancouver and 14 km (8.7 miles) west of Kamloops, a city of 60,000 people, in south central British Columbia, Canada. The mine is adjacent to the Trans-Canada Highway at an elevation of 670 m (2198 ft) above sea level. The ore body is a porphyry copper deposit that has undergone supergene alteration. The major economic minerals in the supergene zone are native copper and chalcocite with chalcopyrite and bornite in the hypergene areas. The grade is 1% with an overall copper distribution - 70% native, 25% chalcocite, and 5% chalcopyrite with bornite and covellite. The ore also contains important but variable amounts of gold and silver. The mill was designed to treat 6350 t/d (7000 stpd). Semiautogenous grinding was selected to minimize capital cost and because of the expected high clay content of the ore, which would have caused problems in a conventional crushing and screening plant. Test work indicated that a recovery of 87% was possible in a circuit incorporating both flotation and gravity separation. Flowsheet Run-of-mine ore is crushed in a 1.06 x 1.65-m (3.5 x 5.4-ft) Allis Chalmers gyratory crusher set at 228.6 mm (9 in.), closed side setting. The surge pocket, below the crusher, is emptied by a Hydrastroke feeder onto number one conveyor, which discharges onto a 180,000-t (198,416-st) coarse ore stockpile. Six Hydrastroke feeders on two conveyors withdraw the crushed material from the bottom of the pile. These two conveyors, in turn, discharge onto the belt feeding the semiautogenous mill. The live storage in the stockpile is approximately 22,000 t (24,250 st), sufficient for three days' mill feed. Primary grinding is accomplished in an 8.5-m (28-ft) diam by 3.7-m (12-ft) long Koppers (Hardinge Cascade) mill (Fig. 1) containing a 10% ball charge and driven by a 4000-kW dc variable speed motor. The mill dis¬charge is pumped by a 10 x 12 G.I.W. pump to a 1.22 x 4.88-m (4 x 16-ft) stationary screen sloped at 20°. Screen oversize returns to the semiautogenous mill (SAM), and the undersize flows by gravity to the ball mill discharge pump box. Secondary grinding is performed in a 5-m (16.4-ft) diam by 8.84-m (29-ft) Koppers overflow ball mill driven by a 3430-kW synchronous motor through an air clutch. The mill is in closed circuit with a Krebs Cyclopac containing 10 635-mm (25-in.) cyclones and the cyclone overflow, at 35% solids and 65% to 70% -200 mesh, is flotation feed. In order to limit the buildup of native copper, circulating in the secondary grinding circuit, a portion of the underflow from the cyclones is processed in a circuit containing screens, cyclones, and shaking tables to produce a finished metallic copper concentrate. Primary mill variable speed drive The overall waste to ore ratio at Afton was 4.5:1. The mining was to be done with only three shovels, which meant that it was highly unlikely that more than one of them would be in ore at any one time. The resulting inability to blend the mill feed made it impossible to prevent wide swings in the grade and grindability. The variable speed do drive motor installed on the semiautogenous mill was selected because of the extreme variability of the Afton ore body. This variability has persisted throughout the lifetime of the mine. There are times, however, when due to ore conditions, the mill is operated at full speed (78% of critical) for extended periods of several shifts duration. There are other times when the mill speed may be changed several times in a 12-hour shift due to changing ore conditions. When ore is processed that contains a fairly large proportion of fine native copper, the primary mill speed and, consequently, the tonnage may be reduced to improve the secondary grind and to maintain an acceptable grind and recovery. High clay ores require less mill speed and more dilute grinding densities. In the latter case, the slower primary mill speed also helps to minimize damage to the mill liners. Approximately 57% of the time the mill operates between 90% and 100% of full speed or between 71% and 78% of critical. The variable speed is also used for inching during mill relines.

Jan 1, 1987

By John O. Marsden

Process selection is the systematic development of the optun.m metal extraction route for a particular feed matenal and has two main objectives: (1) to optimize project economics, principally a function of gold recovery, throughput rate and processing costs, and to develop a process that satisfies all of the proct requirements including, for example, political and environmental considerations.

Jan 1, 1992

By Charles A. Horne

Grinding mill circuits used for particle size reduction of mineral ores commonly use cyclones as primary classifiers. Typically, several individual cyclones are installed in a cluster (Fig. 1) where they can easily be added or valved-out of operation in order to balance classifier capacity with fluctuations in tonnage and recirculating loads as ore grades and hardness vary.

Jan 1, 1993

By Justus B. Deen, Randy Peterson

INTRODUCTION The General Chemical Soda Ash Operation located near Green River, Wyoming produces about 4.5 Mt of trona per year. In July 1989, Mine Ventilation Services Inc. performed a ventilation survey of this complex trona mine which had thirteen active panels spread over 36 square kilometers. The ventilation survey and subsequent study showed that the intake shaft air velocities were at their practical limits (Wallace and Rogers, 1987). The need for additional intake capacity was immediate. The ventilation network modeling delineated the best location for this new intake shaft as it applied to the 5 year ventilation plan. Unfortunately, this location, 6.5 kilometers from the soda ash processing plant, would make heating this intake air very costly. Presently, the intake air is heated by heat exchangers which use waste heat from the plant. Air heating during the winter months is necessary for miner comfort and to prevent potential freezing of water lines in the mine. It was decided to examine the feasibility of heating the air geothermally by coursing it through an old production panel. This method of air heating has been used in this region with good results at the Stauffer Chemical Operation (now Rhone-Poulenc) (Moore, 1985). In 1990, a geothermal heating study examined four different production shaft/panel configurations and a workable design was found. The operators at the General Chemical Soda Ash Operations acted on this design and began raise boring a ventilation shaft in the Spring of 1991. This paper describes the ventilation system, briefly, and the geothermal heating studies performed. Findings of the 1990 geothermal studies are then compared to field data acquired in the Winter of 1992. THE VENTILATION SYSTEM The ventilation system at General Chemical had four shafts serving the mining horizon in July 1989; three of these shafts are located at the Northwest end of the mine. The active work areas had progressed to the South over the past years and supplying ventilation has become increasingly difficult. The 6.1 meter diameter #3 Production shaft and the men and materials compartment of the 6.1 meter diameter #2 Split Shaft had reached their air velocity limits. Conversely, the 4.6 meter diameter #5 Exhaust Shaft was under utilized. Ventilation studies showed the conversion of the 3.7 meter diameter #1 Exhaust Shaft to an intake would provide adequate intake capacity for two years. The next option to improve ventilation was the addition of an intake shaft at the southeast part of the mine at the intersection of H Mains South(H-M-S)and J Mains East(J-M-E) (See Figure 1). A service shaft has been planned for the extreme Southeast end in the late 1990's. Ventilation network analyses showed this interim intake shaft would have to be at least 2.5 meters in diameter to postpone the service shaft construction beyond 1995. The greater the size of the borehole, the further the construction could be postponed. In October 1991, General Chemical commissioned the 4.57 meter diameter #4 Ventilation Shaft near the junction of H-M-S and J-M-E as shown in Figure 1. The L95 panel would be used for air heating as described in the geothermal heating section to follow. GEOTHERMAL STUDIES Geothermal heating studies were performed by MVS Inc. in May 1990. Using a modified code of CLIMSIM, an underground mine climatic simulation model, several different shaft/panel configurations were examined to see which would provide adequate air heating during the winter months. CLIMSIM simulates heat flow into a single underground airway. The program was used to evaluate the heat flow to and from the airway surface and to calculate the resulting change in dry bulb temperature of the ventilating air. CLIMSIM uses inlet air conditions, airway characteristics, and rock thermal properties input by the user to predict the variation of psychrometric and thermodynamic parameters along an underground airway.

Jan 1, 1993

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader's orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature's effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993

By William R. Henkle

High-calcium limestone has been intermittently produced from the Monarch quarry since the late 1800s. Initial production was used in sugar processing and for a smelter located near Salida, Colorado. During the 1920s, Colorado Fuel and Iron Company (CF&I) began to exploit the deposit as a source of flux stone for its blast furnace steel operations at Pueblo. The deposit was operated for many years as a captive quarry by CF&I. In 1984, CF&I closed the quarrying operations at Monarch; flux stone was no longer required since the blast furnaces were taken off line in 198 1. In 1994, Colorado Lime Company, a subsidiary of United States Lime and Minerals, Inc. acquired the property. Limestone was mined from the Castle Butte Member of the Leadville Limestone (Lower Missippian). Some high- magnesium dolomite was also mined during WWII from the Redcliff Dolomite Member which directly underlies the Castle Butte. Past production was from both an upper and lower quarry at elevations ranging from 10,000 to 11,000 feet (3,048 m-3,353 m) mean sea level (m.s.1.). The reserves at Monarch quarry are in a dip slope deposit, occupying the northwest slope of Monarch Hill. The structural geology of the deposit is complex on both a region- al and mine scale. The reserves are located on the eastern limb of the Syncline Hill syncline. The beds on this limb of the structure strike to the northeast and dip to the northwest from 30 to 45 degrees. A major reverse fault separates the reserves into an upper and lower deposit. Numerous smaller normal and reverse faults cut the deposit, requiring a flexible mine plan. At the Monarch quarry, the Castle Butte Member con- sists of two stratigraphic units. The Upper unit (Mlu) is a thick-bedded, fine-grained crystalline dolomitic limestone from 0 to 300 feet (0-90 m) thick. The unit generally has an Si02 content of less than 4 percent. A bedded chert horizon and a karst horizon at the base of the unit locally raise the Si02 content as high as 20 percent. The underlying Quarry Stone unit (Mlq) is a light-gray, massive, bedded, calcilutite/micrite limestone from 90 to 130 feet (27-40 m) thick. The Quarry Stone unit is remarkably uniform chemically throughout it's entire thickness. Average analysis is CaC03 - 95 percent, MgC03 - 3.5 percent, and Si02 - 0.5 percent. The Footwall dolomite unit (Mld) of the Redcliff Member of the Leadville Limestone is a dark gray to black, blocky, medium-to-thick-bedded, calcilutite/micrite dolomite from 150 to 180 feet thick (46-55 m). The upper 100 feet (30 m) of the unit is a low-silica facies with an average Si02 content of less than 0.5 percent. MgC03 content is con- sistent at 39.8 percent throughout the upper 50 feet (15 m) of the unit but varies from 15 percent to 39.8 percent in the lower portion (50 to 100 feet [15-30 m]) of the low-silica facies. The lowest portion of the unit, 100 feet (30 m) to base of unit is high in silica and is not considered chemical grade. Current in-place, surface-minable reserves at the quarry are estimated to be 14 million short tons (st) (13 million metric tons [mt]) of limestone and 50 million st (45 million mt) of dolomite. A 1.4 million st (1.3 million mt) stockpile of finely crushed limestone is also present on the property. Colorado Lime is presently processing approximately 2,000 st (1,800 mt) per month from the crushed limestone stockpile. This material is pulverized and sold to underground coal mines for use as rock dust, some of this product is also used for environmental purposes. Limestone mining is scheduled to resume in spring of 2000.

Jan 1, 2001

23.1-SOURCE, POWER-SYSTEM ELEMENTS A. J. T HUM Basic considerations in providing power for mine production and collateral operations are: 1. Mining operations of any size normally use electric motors for driving all equipment except mobile service units. 2. The electricity for power may be purchased or self-generated, depending on the location, size and specific operating circumstances of the individual property. 3. The major elements of the power system will be the source, either an incoming transmission line from a utility in the case of purchased power or the power plant if self-generated. Energy for the power plant may be water, hydrocarbon fuels, waste heat or nuclear, which will govern the type of prime mover selected. 4. The electricity normally is generated in the form of alternating current and must be distributed to the points of usage. This usually requires a primary substation for transformation to suitable voltages and secondary substations at points of usage throughout the operations, The power is delivered from the primary to the secondary substations over transmission lines or cables, depending on distances, voltages and local conditions. 5. At the points of use, there will be starting and protective devices for each motor. In some instances, direct current will be needed and rectifiers of various types can be used to provide it. 6. The entire electrical system requires suitable switching and protective devices to prevent damage to the equipment in case of power failues or faults; also, in most cases, sufficient metering to establish the demand and amount of electrical energy consumed. 23.2-PURCHASED POWER A. J. THULI 1. Where public-utility or government-generated power is available, it usually is advantageous for the mine owner to purchase rather than generate. Purchased power generally will be cheaper and more reliable than operating a small generating plant except in some cases where waste heat is available as the source of energy and can be used to supply all or a portion of the power requirements. 2. If it is decided to purchase power, the owner usually must participate in the cost of constructing the connecting line from the closest existing utility line to his point of usage. If the connected load is less than 1,000 lip, it probably is best to let the utility provide the primary substation. For larger connected loads the owner can obtain a more favorable "primary voltage" rate if he provides the primary substation to receive the incoming power and transform it to the distributing and usage voltages. 3. The cost of purchased power usually is made up of a demand charge, deter¬mined by the maximum amount of power the customer takes during any 15-min period throughout a month, and a graduated energy charge for the kilowatt-hours consumed-that is, so much for the first block of energy based on the demand,

Jan 1, 1973

By Paul L. Russell, R. G. K. Morrison

9.1-CLASSIFICATION OF MINERAL DEPOSITS AND ROCK MATERIALS After a mineral deposit has been discovered, delineated and evaluated, the next step is to select a mining method that is physically, economically and environ- mentally adaptable to recovering the mineral from the deposit. The term "mineral deposit" is used to denote a concentration of mineral (including rock and coal). Even where there is considerable past experience available, many of the critical design criteria must be determined utilizing only information obtained from an examination of exploratory drill core specimens. The factors that affect this selection are as follows: (1) the spatial characteristics of the deposit (size, shape, attitude and depth); (2) the physical (or mechanical) properties of the mineral deposit and surrounding rock; (3) ground water and hydraulic conditions; (4) economic factors, including grade of the ore. comparative mining costs and desired production rates; and (5) environmental factors, such as the preservation of the surface overlying the mine, and the prevention of air and water pollutants. Of these factors, the spatial characteristics of the deposit and the physical (or mechanical) properties of the mineral and surrounding rock limit the methods that can be employed to mine it. Six types of mineral deposits are recognized, as follows: 1. Massive-A deposit of considerable lateral and vertical extent in which mineralization (or ore) is relatively uniformly distributed. Disseminated copper ores are typical deposits. Dome salt also is included in this classification. 2. Bedded or Tabular-A mineral deposit that parallels the stratification, most often in sedimentary rock, usually laterally extensive, and of limited thickness. Most coal measures and some evaporite mineral deposits (e.g., potash) fall in this class. 3. Narrow Vein-A zone or belt of mineralization (ore) typically long, narrow (less than 10 ft), often dipping steeply, and usually lying within boundaries separating it from neigh- boring rock. Many gold and other metallic minerals occur in narrow veins. 4. Wide Vein-As defined under narrow vein except that the vein thickness is greater than 10 ft. 5. Lentictclar or Pocket-An isolated ore body, or an enrichment of limited vertical and horizontal extent in a massive, bedded or vein deposit. Lead, zinc and iron ores often occur in this type of deposit. 6. Placer-A surface or near-surface deposit, usually tabular and may be of consider- able areal extent, containing mineral particles (e.g., gold, platinum) in detritus (e.g., sand, gravel). The rock materials associated with mineral deposits are classified as follows: 1. Detritus-Sediments and other accumulations of solid particles produced by the mechanical and/or chemical disintegration of rocks, and usually having a low cohesive strength and very low compressive strength (e.g.. soil, sand, gravel, alluvium, playa). 2. Jointed and Fractured-Unbonded-A rock mass, often occurring on or near the surface or in fault zones, in which the joints or fractures contain alteration or decomposition

Jan 1, 1973

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION This method is a variation of cut-and-fill mining where either the wall rock or the vein is too unconsolidated to permit safe mining by conventional cut-and-fill methods. Basic development consists of driving a 2.4 x 2.7-m (8 x 9-ft) haulage heading laterally in the footwall side of the vein. Crosscuts are driven over to the vein at 91-m (300-ft) intervals. Then the vein, at each inter¬section, is mined out to a distance of about 9 m (30 ft ) above the track level. After the installation of an ore chute, scrams or intermediate drifts are driven in both directions along the vein. Mining then starts imme¬diately below the level bounding the upper limit of the stope. A cut varying between 3 and 4.2 m (10 and 14 ft) in depth and mined for a distance of 45.7 m (150 ft )along the strike is taken from the orepass in each direction (Fig. 1). In this mined-out void, the floor of the cut is equipped with 203 x 203-mm (8 x 8-in.) caps hitched into the wall with steel saddle hitches installed on 1.5-m (5-ft) centers. Double wood stringers, 152.4 x 152.4 mm (6 x 6 in.), are then installed on 1.2-m (4-ft) centers longitudinally down the length of the stope. Reinforc¬ing wire mesh is also placed, overlying each mat of timber. Directly above the stringers, stulls are installed from hanging wall to footwall to hold the timber in place during the sand-filling operation. Then a cement¬sand mixture in a ratio of about 1:10 weight is poured to a depth of about 2.4 m (8 ft). The entire cycle is then repeated down to the scram drift. Another variation of timbering is illustrated in Fig. 2. There is a vein width of approximately 5.5 m (18 ft) with the same unconsolidated ground conditions. The primary difference between handling this situation and the previously described undercut-and-fill method is that standard timbered sets are installed in each excavated stoping void rather than stulls. Once again the basic method is to work down the ore block from an upper timbered drift to a lower timbered drift. Cuts are taken from a timbered raise with a chute on the stope side. Each piece of ground excavated is essentially two sets high, 5.5 m (18 ft), by two sets wide, 5.5 m (18 ft), by the length of the cut along the strike of the vein. The timbered sets are 2.4 x 2.4 x 2.4 m (8 x 8 x 8 ft). The net result is, therefore, two sets of timber on a top floor separated by doubled-up 76-mm (3-in.) lagging from

Jan 1, 1982

By Robert A. Jankowski, George E. Niewiadomski

INTRODUCTION The utilization of longwall mining technology in the United States has steadily increased since the first longwall plow system was installed in 1952. At the errs of FY 1992, some 76 coal mines were employing longwall mining systems for coal extraction, and approximately 78 shearer and 3 plow faces are operating nationwide at any given time. Although the number of operating longwalls has remained relatively constant over the last five years, longwall production levels have increased significantly during this period. During the same timeframe, the number of continuous miner sections has decreased by 13 pct., from approximately 1438 in FY 1988 to less than 1250 in FY 1992. According to Mine Safety and Health Administration (MSHA) data, the average production of longwall sections increased from approximately 2400 tons per shift (tps) in FY 1988 to more than 3100 tps FY 1992. In fact, the average production has more than tripled since 1978, when it was only 850 tps. Approximately 25 pct. of operating longwalls are capable of producing in excess of 4000 tps. Longwall production currently accounts for nearly 36 percent of U.S. underground coal production, compared to 4 pct. in 1978. These improvements are attributed to improved longwall equipment and increased availability, larger longwall panels and automation. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems more frequently than other mining system. Although dust levels have remained relatively unchanged over the past five years, averaging 1.6 mg/m3 and 1.9 mg/m3 based on results of operator and inspector sampling, respectively, during FY 1992, approximately 25 pct. of the operating longwalls were in noncompliance during any given bimonthly sampling cycle. Although modest gains in longwall dust control technology have been made, these have been overshadowed by significant increases in production rates. As more coal is mined, more dust is generated (Figure 1). Therefore, the increase in longwall productivity has meant that far more dust is being produced which must be controlled. [ ] In view of the current compliance record, any efforts to further increase longwall output, as has been forecasted, must be accompanied by: (1) the reduction of dust levels at existing operations through the proper installation and maintenance of suitable engineering dust controls; and (2) the advancement of dust control technology for today's and future longwalls that will enable all face personnel o work in an environment that is free of excessive levels of respirable coal mine dust. MSHA'S RESPIRABLE DUST CONTROL PROGRAM Since 1972, federal regulations have required each coal mine operator to continuously maintain the average concentration of respirable dust in the mine atmosphere during each shift in the active workings at or below 2.0 mg/m3 through the application of environmental dust control methods. The regulations provide for further reduction in the dust standard whenever the

Jan 1, 1993

By M. Tirmarche, J. Brenot, J. W. Piechowski

INTRODUCTION Statistical analysis of results obtained by workers survey is very often limited to the determination of the collective dose and mean annual values. This information is not sufficent by itself for radiation protection purposes since the cumulative exposure of a worker during his working life is not taken into account. A more complete analysis would be obtained by considering both: [ ] These two notions are different. The former depends on the evolution of the protection with time and is related to annual limits (ICRP, 1977 and ICRP,1977 a). The second depends mainly on the works performed during the period of survey, the interference of protection evolution is weakened. So it is useful to foresee how the individual average annual doses would be when considering survey periods of 5, 10 years, or more. STUDIED POPULATION In order to analyse the two previously mentionned notions it is necessary to follow up a well defined population of workers which is continuously exposed to the radiological hazards on a long enough period. The selected population is that of the workers of the French uranium mines always present during the 1971-1979 period (9 years). The number of individuals is 937. The radiological hazards are: 1. exposure to radon and short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation. The workers of the uranium mines are exposed to these radiological risks in different ways according to the work performed. It is therefore necessary to subdivide the population into more homogeneous groups with respect to the radiological risks. Three groups are considered: - Group 1 : 227 individuals whose radon and dust exposures are always nil - Group 2 : 449 individuals whose radon and (or) dust exposures are different from 0 every year - Group 3 : 261 individuals represent a mixed category. Some features of these groups are given in table 1. [ ] The 937 followed individuals represent approximatively the half of the whole population of the French uranium mines. Taking into account the procedure adopted to select the studied population, it appears clearly that this population is not representative of the whole miner population. DOSIMETRIC RECORDS Three risk indicators are considered .Individual annual exposures to radon and its shortlived daughters. They are determined by ambient monitoring based on radon concentration measurements and recording of the times elapsed in the various workplaces. For each worker the annual exposure is represented by the mean annual air concentration and is expressed as a fraction of the maximum annual concentration (MAC). Given the administrative arrangements and the effective state of equilibrium between radon and its daughters, the maximum annual concentration is practically equivalent to 1 Working Level = 2.08 x 10- 5 jm-3. (UNSCEAR, 1977). . Individual annual exposures to long-lived ore dust which are also expressed in fraction of the maximum annual concentration. . Individual annual doses of external irradiation (X and [y] rays) expressed in mSv (= 10-3 Sievert). Irradiation monitoring is based on use of individual film badges.

Jan 1, 1981

By Lance Rasband, Richard Hanke, John Starcevich

"The world’s largest tunnel boring machine (TBM), at the time of her launch in 2012, the TBM locally referred to as “Bertha,” is incapacitated due to mechanical failure. Bertha’s stoppage places her 25m below the surface between the aged Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to access all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Due to the limited area above the tunnel alignment and physical constraints created by existing infrastructure, the dimensions of the otherwise symmetrical shaft are heavily impacted, thereby requiring special attention to design and layout. Consequently, the shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude. INTRODUCTION Mining on Seattle’s SR99 tunnel began in July of 2013. Initial mining progressed slowly through a 4.5 m thick fiber-reinforced concrete headwall before immediately entering the first of three planned safe havens. Once through the headwall and safe haven the machine would move through roughly 122 lineal meters of jet grout improved soil at a rate of slightly over 1.6 m per day. It was anticipated that once mining has passed through the improved area, “Bertha” – now the world’s 2nd largest tunnel boring machine (TBM), would be moving at a rate of almost 11 m per day. By the end of October 2013, Bertha had mined roughly 131 m, averaging 1.4 m per day, and had begun mining within native soils. By the start of December 2013, tunneling had reached the 244 m mark and Bertha was now averaging 3.6 m per day, achieving as much as 12.8 m of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt. Initial reports stated an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure within the ground around the TBM, to allow the contractor’s personnel to inspect the cutter head from within and also to investigate for the presence of obstructions at the face of the cutter head. During inspection, the contractor’s crews found fragments of steel pipe entangled in the cutter head. The steel was apparently from an abandoned 254 mm diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, she attempted to move forward but was only able to generate a slow crawl."

Jan 1, 2016

By M. Pawlik

Canadian sylvinites contain over 90% of KCl and NaCl and a few percent of water-insoluble minerals. Cationic flotation is used to produce KCl concentrates. Since water-insoluble minerals appear in the pulp as slimes, and since long-chain primary amines are utilized as a collector, desliming is essential. The potash industry utilizes different desliming methods. This may involve selective flocculation of the slimes with polyacrylamide and removal of the flocculated product by flotation, or mechanical desliming with the use of classifying cyclones. Whichever method is applied, desliming is never complete; the flotation feed after desliming still contains about one percent of the slimes which heavily affect collector consumption and flotation selectivity. Therefore, the remaining slimes have to be rendered inactive by “blinding” them with polymers such as carboxymethyl cellulose or guar gum. The commercial blinders used by the potash industry include natural and synthetic polysaccharides. The most common is the use of carboxymethyl cellulose (CMC) and guar gum (GG). These are quite different polymers, while CMC is anionic, GG is non-ionic; while the applied CMCs are of relatively low molecular weight (about 300,000) GGs have much higher molecular weight. Guar gums are also heavily used as the depressants of naturally floatable gangue in the processing of platinum-bearing ores, and according to Harris et al. (1999) quite a large variety of modified guar gums are available in South Africa for this application. Cheng et al. (2002) claim that natural guar gum’s molecular weight is 1.935 • 106. Robinson et al. (1982) found that the molecular weights of five grades of commercial guar gums ranged from 4.4 • 105 to 16.5 • 105. The highest molecular weight sample is then very close to the natural guar gum studied by Cheng et al. (2002). According to the manufacturer, the Rantec KP4000 guar gum which is used by the Canadian potash industry has a molecular weight of about 1.5 x 106. Since both KCl and NaCl are soluble in water, the flotation process is carried out in saturated brine. At 20 oC, 1450 kg of NaCl-KCl-H2O saturated solution contains about 0.300 kg of NaCl, 0.150 kg of KCl, and 1 kg of water (Gaska et al., 1965). Thus, in the saturated NaCl-KCl brine there are about 5.1 kmole of NaCl and 2 kmole KCl per 55.5 kmole of water. This gives 3.9 molecules of water per each ion assuming complete dissociation of NaCl and KCl. Thus, it is obvious that all water molecules in the saturated brine must be bound in the hydration shells around the hydrated ions. The surface tension of the NaCl-KCl saturated brine was recently measured to be 85 mN/m (Laskowski et al., 2003).

Jan 1, 2004

By I. Michalakis

A geological and geophysical study was con-ducted at the area of Stylos, Hania in order to study the possible mechanisms of saltwater contamination. A new detailed geologic map in scale 1:5,000 was combined with the results of a time lapse geophysical survey using seismic and electrical methods. A fault system in the N-NE direction possibly favors the saltwater intrusion.

Jan 1, 2006

By J. P. Morgan

The Vesta Preparation Plant of the Jones & Laughlin Steel Corporation is located on the Monongahela River, eight miles south of Brownsville, Pennsylvania. This plant is capable of cleaning 2400 NT/hr of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables. handle the -1/4" fraction of the raw coal feed. Cleaned -coal goes to boot classifiers where the +48 mesh material settles and is removed by bucket elevators. This 1/4 x 48 mesh material is then sent to centrifugal driers for dewatering. As designed, the minus 48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and dewatered by filtration. The-products of the heavy media circuit, the launder-table-boot-drier circuit and the cyclone-thickener-filter circuit are combined to constitute the shipped metallurgical coal. This Vesta-Shannopin mix is combined at J&L's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke.

Jan 1, 1962

By G. H. Gronhovd

The U.S. Geological Survey estimate of the total remaining reserves of lignite in this country as of Jan. 1, 1967 was about 448 billion tons. This represents 27 percent of the total coal reserves on a tonnage basis and about 17 percent on a thermal basis. Approximately 98 percent of these reserves are in a vast lignite field located in western North Dakota and eastern Montana. This field also extends north into the Canadian province of Saskatchewan. Despite these large reserves and relative ease of mining by stripping operations, lignite production historically has accounted for less than 1 percent of the national total. This is largely due to the fact that the lignite deposits are located in an area that has no large centers of population and the economical radius of transportation is limited by its relatively high moisture and low heating value. Commercial utilization of North Dakota lignite for power production became firmly established in the mid-1920's with the development of the first successful lignite-burning equipment. Most of the early lignite-fired boilers were equipped with spreader stokers, but as the size of the plants increased, pulverized-coal firing became the more popular method, and with few exceptions, the plants built during the past 15 years are pc-fired.

Jan 1, 1968

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By Dan J. Van Roosendaal

A closely spaced grid of survey points was installed over the tensile zone of a longwall panel in southern Illinois and monitored daily during subsidence to document the complex ground-surface movements associated with dynamic subsidence. Vertical and horizontal displacements were used to calculate maximum tilts and principal strains within the grid. The dynamic nature of subsidence is made evident by changes in both the direction and magnitude of maximum tilts and principal strains. The maximum tilt (smax) of 0.036 and maximum tensile strain (Emax) of 0.027 were measured after subsidence and were oriented transverse to the longwall panel. Observations of surface fracturing were correlated with strain determinations to estimate a surface strain at incipient cracking (E;) of 0.006 to 0.009. Using shallow inclinometers, a linear variation of horizontal displacement with respect to depth was observed, suggesting a neutral¬axis bending mechanism for near-surface deformation. Horizontal displacements transverse to the longwall panel reduce to zero at a depth of 40 feet. A linear relationship between strain and curvature was used to estimate ground-surface curvatures associated with Emax (0.00068 ft-1) and E; (0.00015 to 0.00023 ft-1). The curvature estimates are consistent with published results.

Jan 1, 1986

By A. A. Terchick

In 1970 U. S. Steel acquired the physical assets of mine, mine property, and preparation plant of the Crystal Block Coal Company near Thacker, Mingo County, West Virginia. The facility, identified as U. S. Steel Mine No. 20, is administered and operated as a production unit of U. S. Steel Gary District, Gary, West Virginia. Mining operations of the No. 20 mine are conducted in the high-volatile Alma seam. The preparation plant, which originally had a capacity of about 150 tons per hour (tph) of raw-coal feed, had process circuitry consisting of a Daniels heavy-media vessel for cleaning the plus-1/4-inch raw coal, a McNally-Pittsburg feldspar jig for cleaning the 1/4 inch by 28 mesh, and Daniels flotation cells for treating the 28 mesh by 0. No water-classification system existed. Refuse tailings from the plant were pumped to several surface lagoons which were decanted to the stream. The settled solids were removed and trucked to the coarse-refuse disposal area. Water make-up requirements were supplied by a small mine-water surface reservoir and augmented with stream water. Expansion of production from the property required an increase in preparation-plant raw-coal-feed rate capacity from

Jan 1, 1974