Search Documents

By Geoffrey Purcell

Improvements which have been made in commericial flotation systems during the past fifty years have resulted more from trial and error methods in the mill than from research in the laboratory. Research has often provided explanations of why mill changes have improved the metallurgical process. Hopefully, in the next fifty years, changes in mill flowsheets will come about, primarily, as a result of research work. However, since minerals, in their infinite variety, cannot be reduced to a standard state, research on commercial ores will have only a local utility, and research on pure minerals will have little commercial application. What will emerge from research on pure systems are mechanisms of adsorption, and this in turn may throw some light on the very much more complex adsorption processes taking place in the pulps of commercial ores. Quartz, without a doubt, has been the subject of more research effort than any other mineral, but we are still a long way from completely understanding its behavior in flo¬tation. Hematite and calcite have received considerably less attention. Ores containing a mixture of all three minerals, however, are commercially important, and the iron deposits in Alabama have been extensively studied by the United States Bureau of Mines (1). The literature reveals no reports of research on synthetic mixtures of all three.

Jan 1, 1967

By Hemendra N. Kalia

To plan a safe and efficient coal mining operation, the design engineer should use all the available information regarding the property to be exploited. The reliability of the mining operation must be as high as possible so that the plants relying on the coal can operate at the maximum design capacity. A good design should incorporate all of the known geological characteristics of the deposit, the structural and physical properties of the coal, as well as the rock which will form the roof and floor of the mine openings. A systematic method is proposed as a guide to insure a mine design that will be safe, efficient and will minimize surface disturbances resulting from mining operations. It is anticipated that the method proposed will result in maximum extraction at perhaps minimum cost to the operator. In general, to develop a mining area, several factors are systematically reviewed: (1) determination of the economic minability of the deposit, (2) the computation of the coal reserves, (3) the marketability of the coal, and (4) the life of the property. In general, boreholes are drilled in a predetermined pattern and geophysical or geological methods are used to log the boreholes. The information so obtained is primarily used to determine the quality and the extent of the deposit and to determine to some extent such geological features as faults, barren areas, washouts, and channels.

Jan 1, 1973

By Greg Border

Many unique ventilation problems have been faced as Avery Island Mine's large openings have been mined. High humidity of outside air combines with the hygroscopic salt to create a corrosive atmosphere. Massive rooms preclude routine use of brattices to direct air flow to the working faces. Large amounts of explosives are consumed in single blasts. Resulting concussion pounds air control structures and ANFO ignition creates large amounts of nitrogen dioxide in single rooms. Geologic constraints confine new shafts and slopes to areas thought to be free of potential ground water hazards. Dust control techniques are limited by dry product demanded by customers. The Avery Island Mine's ventilation system has evolved to deal practically with the conditions and to dependably provide fresh air to the miners. International Salt Company's Avery Island Salt Mine, a multiple level room and pillar operation, has been mined steadily since about 1900. It is known as one of the "Five Island" salt dome mines of South Louisiana's Gulf Coast. Production from the area places Louisiana first in United States rock salt mined tonnage, according to the United States Bureau of Nines, 1982 (1). International Salt Company is a major force in U.S. salt production, as it also operates mines in Detroit, Michigan; Cleveland, Ohio; and Retsof, New York; a solar salt facility in Bonaire, Netherlands Antilles; and a solution mining plant at Watkins Glen, New York.

Jan 1, 1983

By Neal P. Cochran

The United States is faced with increasing demands for electricity, coupled with continuing demands for crude oil and gas. Superimposed on these' national requirements are our national requirements for clean air and elimination of thermal pollution of our rivers. From the coal viewpoint, this situation is complicated still more by the rapid advances in nuclear power. In this paper, I hope to show a way to use our Western coals as a solution to this involved national problem by producing: 1. High quality crude 2. Low cost power 3. Economic byproducts We could expect these products to be made at one site in an integrated plant that would mine (extract) coal, process it, and convert it to electricity. Perhaps the most important attribute of the plant is its reduced water requirement and the elimination of air pollution from the power cycle. Quite logically, such a plant would probably recover valuable byproducts, such as pipeline gas, sulphur, cement, aluminum, and the like. Although the plant projected in this paper is a conceptual one, it is based on work now underway by Government and industry. Prediction of the future is a most hazardous occupation, but plants such as the one projected are based on current knowledge and can be expected to reach commercial operation in the near term future.

Jan 1, 1967

By Harry Teicher

The subject of Specialty Silica Products could encompass a broad range of materials, some of which would be familiar to members of the Society of Mining Engineers. With the concurrence of your chairman, I have chosen to limit my remarks to synthetic materials, not including such siliceous materials as diatomaceous earth, asbestos, quartz and clays. For purposes of discussion, I have classified Specialty Silica Products into two groups -- powders and liquids -- which I will discuss in that order and which are categorized in Figure 1. The synthetic silica powders are amorphous to x-rays and are manufactured by various processes resulting in products of a wide range of physical and chemical properties, as well as functional performance and applications. Applications or functional properties are generally dependent upon such physical properties as micron-sized particles exhibiting large surface areas per unit weight and low apparent bulk density. Their presence in various systems modify surface properties. As summarized in Figure 2, they act as viscosity modifiers, flow conditioning agents, anti-slip agents, anti-blocking agents, flatting agents in surface coatings, reinforcing agents in polymers such as silicone rubber and numerous other applications. Although the various types of silicas exhibit various levels of functional performance in these end uses, they are not usually equally effective as direct replacements and I will briefly discuss the various types of materials.

Jan 1, 1974

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By Jess W. Smith

The carbonaceous Monkemeyer sandstone member of the Creede Formation on Bachelor Mountain hosts alteration and mineralization which contrasts with other silver deposits of the Amethyst system. More than 20 million ounces of silver are contained in disseminated mineralization in the volcaniclastic conglomerates and sandstones. Hydrothermal fluids entered the Creede Formation directly from the Amethyst fault system and mixed with flowing meteoric ground waters trapped beneath the Monkemeyer sandstone. Portions of the basal rocks of the Creede Formation were argillically altered by more dense acidic fluids generated by boiling. The carbonaceous base of the Monkemeyer and much of the conglomerates below were mineralized and well silicified. Deposition of the mineralization resulted from two processes: (1) reduction by carbon in the Monkemeyer, and (2) fluid mixing in the conglomerates. Monkemeyer mineralization is confined to the carbonaceous basal material and silver content is relatively consistent. Silver is contained in acanthite which is commonly associated with traces of galena, chalcocite, covellite and sphalerite. Fluid mixing and mineral deposition in the poorly sorted conglomerates was controlled by the highly variable porosity and permeability. Anomalous silver contents are dispersed throughout a large volume of conglomerates but zones of higher silver content reflect the crude layering of the conglomerates. Acanthite is finely disseminated in pore spaces and partly replaces some detrital magnetite. other metallic minerals are rare in the main zone of mineralization.

Jan 1, 2013

By Keith A. Heasley

The objective of this paper is to back-analyze the August 6th ,2007 collapse at the Crandall Canyon Mine in order to better understand the geometric and geo- mechanical factors which contributed to that collapse. In this work, the LaModel boundary-element program along with the best available information is used for the back- analysis. To initiate the analysis, a six step base model of the mining in he Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters: rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis , a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) Overall, the area was primed for a massive pillar collapse because of the large area of equal size pillars, 2) The abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse, 3) From the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2012

Optimal gold recoveries largely depend on efficient liberation of the gold or gold-bearing minerals as well as on maximum access for the lixiviant. Thus, crushing and grinding may become the most costly part of gold ore processing. It may, in fact, represent 50% to 70% of a plant's operating costs (Michaelis, 1989). The increasing significance of refractory gold will require even more cost-efficient comminution of ultrafine sulfides and/or native gold. Transitional ore zones with semi refractory gold may respond to direct leaching if better particle fracturing is being achieved (Baum, 1991, 1993a). Many oxide ores have been left in the ground because they were unsuitable for heap leaching since conventional comminution could not facilitate economic gold extraction. Also, the costs of conventional bal1 mill operations did not permit the recovery of gold from many ultrafine, low-grade refractory ores. As shown by Marsden et al. (1993), the trend to treat ores with progressively lower grades will involve power-and leach-efficient grinding applications. Our current laboratory work shows that high-pressure grinding roll (HPGR) Polycom grinding may enable many mining companies to add large amounts of these "non-leachable" ores to their current heap or mill leach feeds. This finding may dramatically change the economics of many oxide gold ore operations and may add significant reserves to ores amenable to direct cyanidation.

Jan 1, 1994

By J. Herbst, A. J. Lynch, E. V. Manlapig, G. C. Throne, J. S. Hall, G. Poling

Modelling of industrial sulphide flotation based on data collected in several flotation plants is discussed. A mechanistic approach is used in which it is recognised that flotation is a two stage process with concentration occurring both in the pulp and in the froth. The important features of the model, which is a kinetic model, are – 1. for each particle species there is a range of flotation rates which corresponds to the range of particle sizes, 2. the flotation rates of the liberated gangue particles which have no hydrophobic properties are dependent on the flotation rate of water and are controlled by variables such as the air and frother addition rates, and the pulp level, 3. as an approximation the valuable sulphide particles may be regarded as being present in two groups with high and low flotation rate constants, 4. increase in the addition rate of collector tends to increase the proportion of sulphide particles which are in the high flotation rate constant group. The actual flotation rate of each group of particles is a combination of an "inherent" flotation rate and a flotation rate which is dependent on the flotation rate of water, at particular air and frother addition rates and pulp levels there is a physical limit to the rate at which particles can be transported into the concentrate and this is recognised in the

Jan 1, 1976

By J. Engesser

A research project supported by the Minnesota Department of Natural Resources and the Iron Ore Cooperative Research Committee was undertaken to reduce the dissolution of fluoride into process water during taconite processing. Leach tests were conducted using rod mill feed samples and water containing varying concentrations of calcium and sodium. Laboratory liberation grinds were performed to evaluate fluoride rejection during grinding and magnetic separation. Tube furnace tests were conducted to evaluate fluoride volatilization during pellet induration. The results indicate that fluoride concentration of process water is a function of both calcium and sodium concentration in process water. It appears that less than 1 percent of the fluoride present in rod mill feed will dissolve in process water during grinding. More than 90 percent of the fluoride present in rod mill feed is rejected with tailings during size reduction and magnetic separation. The furnace tests demonstrate that bentonite and fluxstone (calcite and dolomite) addition to taconite concentrate during pellet production increases the amount of fluoride that volatilizes during induration. Lime hydrate addition to pellets decreases the amount of fluoride that volatilizes during pellet induration. During acid pellet production approximately three times more fluoride enters the water during induration-off-gas scrubbing than during grinding. When fluxed pellets are produced three to eight times more fluoride enters the water during off-gas scrubbing than during taconite grinding.

Jan 1, 2004

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By A. Subbotin

During developing the Ingulska mine at the Mi-churinske uranium deposit in the central part of Ukraine the radioactive rock dumps have been piled. A height of dumps reaches to 15-25m. They occupy a large territory and can be a source of covering with radioactive dust the area around the Ingulska mine. Uranium content exceeds 0,01% in all dump rocks samples while in the dust fraction samples it ranges from 0,01 to 0,06%. Uranium content in road dust at the dump?s foot reaches 0,137%. A new (for Ukraine) method of f-radiography of tree and bush leaves sampled at the territory about 100km2 has been used. It is based on fission of 235U nucleuses due to heat neutron influence in a nuclear reactor and on following study of the Lausan films with tracks drawn by the fractures of these nucleuses. Uranium content of the dif-fusion-disseminated dust type is (0.9-22.2)?10-6% while in the individual particles it can be considered much more because of burned holes in Lavsan above them. The dust content with uranium in Kirovograd reaches to 20-50 part/cm2 while near the dumps it ranges from 100 part/cm2 to 300 part/cm2 in the radius of 1,5-2km from the Ingulska mine.

Jan 1, 2005

By G. S. Grainger, R. A. Cummings, F. S. Kendorski, R. L. Butts

Georgia Power Company's Rocky Mountain Project, located approximately ten miles northwest of Rome, Georgia, in the Valley and Ridge Physiographic Province, is a pumped-storage facility rated at approximately 800 megawatts of peaking energy. Geological field explorations and borings enabled the division of the rocks along the tunnel and shaft alignment into distinct lithologic units and defined the ground--water regime. Field explorations included a detailed analysis of the rock mass discontinuities at available rock unit exposures. Testing of rock strengths was performed in several phases in both the field and the laboratory. The field testing consisted of point-load testing, geophysical testing, in situ load testing, and hydro-fracture testing. Laboratory testing determined the Brazilian split-tensile strength, the unconfined compressive strength, the triaxial compressive strength, the joint-direct shear strength, and the pulse velocity. The rock mass along the tunnel and shaft was also characterized by empirical classification systems. The classification systems included the Rock Mass Rating (B1IR) and the Rock Mass Strength Determination (RHSD). The results of the field explorations, field testing, laboratory testing, and rock classifications were used to divide the rocks into two structural groups. These rock groups were defined as volumes of rock wherein the rock mass behaves similarly in response to the excavation. Each group, therefore, required separate rock engineering consideration.

Jan 1, 1986

By Jasper D. Ward

The Indiana Limestone Company has developed an insulated, thin and comparatively light-weight pane 1 suitable for use as a spandrel panel in a curtain wall. The panel is about four inches thick and is composed of limestone backed with insulation. The inner surface of the insulation is protected with asbestos-cement board or a metal pan, depending on the type of insulation, building-code requirements and appearance (if the surface is left exposed). The limestone is cut to the size of the spandrel openings and the insulation and backup is applied in the mill ready to be shipped and in- stalled in the wall grid, A mortarless and waterproof joint with the metal frame components is achieved through the use of neoprene, thiokol, and caulking, The limestone is "dirt-proofed" (waterproofed) in the mill to slow down discoloration. The panel weighs more than some presently used materials. However, ILCO's architects and engineers have found that curtain wall systems capable of withstanding imposed wind loads are made up of sections large enough to carry this extra load of stone with little or no modification to the size of the metal frame. Limestone, a traditionally sound material, can be used in this new way without losing any of its natural qualities of dimensional stability, resistance to fire, and permanence.

Jan 1, 1959

By L. Alan Weakly

The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement - fly ash mortar. Although the fully bonded bolt concept is not new, as exemplified by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1) (2) the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation’s Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since December of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the grout- rebar system.

Jan 1, 1977

By Gian-P. Lozej, Ross Y. Black, Sami S. Maddah

The Zabirah bauxite is a Cretaceous paleolaterite exposed by postTertiary uplift and erosion of the Phanerozoic sequence. The laterite profile, which is preserved in situ, occupies a prominent angular unconformity over a sequence of sandstones, siltstones and mudstones ranging from Late Triassic to Early Cretaceous in age, and is overlain by a Late Cretaceous terrigenous and carbonate package. The profile is known to be preserved over an area of 250 sq km and at depths below the present surface of up to 80 m. The bauxite layer is hard, compact and predominantly pisolitic, with a variety of subordinate, superimposed textures resulting from post-formation alteration. The bauxite minerals are boehmite and gibbsite. Boehmite generally predominates, and the boehmite:gibbsite ratio averages 2:1, with a marked tendency for the proportion of boehmite to increase down the profile. Kaolinite, a major constituent of the profile, is concentrated in two zones, one above and one below the pisolitic bauxite layer. Iron content is variable and bears a direct relationship to parent-rock lithology. Genesis and preservation of the bauxite are due to the favourable coincidence of a number of geological controls of which the most significant are the local structural and sedimentary regimes, the lithology and chemistry of the parent rocks, and the Cretaceous paleogeography of the region.

Jan 1, 1984

By Jaril B. Lavrencic

The unique and irregulator distribution of working places in a mine always poses the two questions: - which and how much production equipment is to be used, - what production can be expected. Since the development of analytical methods would be impractical for such cases, a lot of computer programs has emerged in recent years trying to simulate the productiom process and thus find the best answer. The usege of a simulator has its dark side well felt by the author(s) of such a program: the credibility and the confidence of the customer. Using the simulator means to respect and to incorporate all the restrictions imposed by the narow underground space, methods of production, safety regulations etc., which can turn out to become a major programming effort. If the program is not properly structured, it will be used for a single special' case only, and never again. In this paper the structure and internal mechanism of the simulator is described for which the author believes that can easily be adapted to conditions of various underground and open pit mines. MINSIM tries to reach the following rather ambitious goals: 1) Estimation of the production before opening the mine, or a part of the mine. 2) Training the personnel to make decisions. 3) Making the daily time schedules for the entire fleet of the equipment units.

Jan 1, 1989

By Ralph H. Knode, Stephen P. Collings

INTRODUCTION The Crow Butte uranium deposit is located in northwest Nebraska near the town of Crawford (Figure 1). The deposit was discovered during the fall of 1980 by Wyoming Fuel Company, operator of the Crow Butte Joint Venture. The Crow Butte Joint Venture is owned 50 percent by Wyoming Fuel Company, a subsidiary of KN Energy, Inc.; formerly Kansas-Nebraska Natural Gas Company, Inc., 40 percent by Ferret Exploration Company, Inc., and 10 percent by First Exploration Company. A preliminary announcement made in January 1981 indicated a "probable potential" reserve in excess of 25,000, 000 pounds U303. Drilling during 1981 and 1982 confirmed these reserves and indicated the presence of more than 30,000,000 pounds U308 having an average grade in excess of 0.25 percent U308. Wyoming Fuel Company was initially attracted to the area in 1978 by favorable regional geology for sandstone uranium deposits and weak radioactivity noted in regional oil and gas holes. Exploration drilling began in 1979 following the formation of the Crow 3utte Joint Venture. Drilling has continued up to the present, at which time the Joint Venture is ready to proceed with a pilot scale solution mine. Environmental baseline data have been acquired and the permit applications for the pilot scale mine have been submitted to the Nuclear Regulatory Commission and to the applicable state agencies in Nebraska.

Jan 1, 1984

By P. Michael

Proponents of geomorphic mine land reclamation have criticized current reclamation practices in the coal fields of steep-sloped Central Appalachia as too narrowly focused on civil engineering principles and neglectful of the functional and aesthetic benefits of reclaiming mine sites in ways that mimic natural landforms and drainage patterns. They observe that current mining and reclamation practices are radically transforming the mountain-and-valley terrain into gigantic flat plateaus and, in doing so, disrupting the beauty and ecology of the natural landscape. Instead of designing and constructing linear or planar surfaces and unvarying slope gradients during the reclamation process, they recommend ?landforming,? i.e. the adoption of curvilinear, compound slope forms that blend well with the surrounding physiography and represent the result of naturally stabilizing geomomorphic processes. The authors feel that the concept of geomorphic mine land reclamation is sound, however, its application to the Central Appalachian coal fields faces significant--albeit not insurmountable--challenges. They include: (1) existing reclamation enforcement regulations that are focused on civil engineering principles and not explicitly supportive of geomorphic methodologies; (2) regulatory agencies? current intent to limit the down-gradient reach of excess spoil fills in order to allay disruption or burial of natural streams; (3) actual or perceived increases in reclamation costs; and (4) the challenge of designing and constructing ?natural? landforms that are mature and stable in an otherwise youthful, erosional landscape.

Jan 1, 2010