Search Documents

By K. K. Wu

In some cases, coal barrier pillars must be relied on to withstand high hydrostatic pressures in order to prevent inundation of active mine workings. Such barriers are particularly important in areas, such as parts of West Virginia, where much of the future mining is down dip of mines which have been abandoned, or are currently being worked. Also, where multiple seam mining is conducted, a barrier pillar in one mine may be critical to safety in a mine in a lower seam. MSHA's Coal Mine Safety and Health district offices and the Mine Waste and Geotechnical Engineering Branch of the Pittsburgh Technical Support Center, have recently been involved in the study of barrier pillars in Kentucky, Virginia, West Virginia, Ohio and Oklahoma. In this paper, the factors involved in determining the required width of pillar are discussed, past practices for sizing barriers are reviewed, and related current Federal regulations are examined. In addition, the results of laboratory testing of bottom rock are presented.

Jan 1, 1980

By Armin C. Supp

Since 1975, about a dozen high capacity flotation plants have been installed in the Ruhr district. Depending on the size of the preparation plants, the design capacity of the flotation section is between 100 - 150 t/h. The flotation units generally comprise rougher and cleaner stages in which 5 to 6 or 4 to 5 agitators respectively are arranged in line. The unit volume allocated to each agitator is up to 16 m3. The type of flotation machines, the design of these plants and their instrumen¬tation and control equipment are described in detail. The run of mine coal in the Ruhr district is characterized by a wide variety of the volatile matter. Generally, a distinction must be made between coals with more than 30 - 35% V.M., which are preferably used in power station, and coal with lower V.M. content, which are preferably used as coke-oven feed. The difference between these coals in respect to grain-size distribution, ash cotent and flotation properties will also be described in detail.

Jan 1, 1985

By Chris A. Minnucci

In 1978, the U.S. Department of Energy funded a 2-year study to identify and quantify causes of the post-1969 coal mine productivity decline. A large number of factors hypothesized to have affected productivity during this period were analyzed using regression techniques. The results were particularly interesting for two of the factors--mining method and shift scheduling. The study results indicate that the use of longwall mining has an insignificant impact on overall mine productivity, compared to other methods, and mines operating on a two-production shift per day schedule are more productive than mines employing other shift schedules.

Jan 1, 1984

By F. W. Bond

Predictive ground-water modeling is currently being applied to a wide range of engineering applications. In recent years models have been used to evaluate the effect of large ground-water withdrawals on regional water supplies; subsidence associated with overpumping; siting and design studies for chemical dumps; siting and safety aspects of nuclear waste storage; and heavy metal migration from disposal sites. Similar modeling techniques could be used to analyze water-related problems in the minerals industry such as mine dewatering (both open pit and underground), environmental and pollution control, and process water supply and disposal The objective of this discussion is to describe how ground-water models are being used to assist in the solution of water-related problems outside the industry and to extrapolate that use to mining problems.

Jan 1, 1980

By Robert D. Norris

Heap leaching provides a method of economically recovering gold from low grade ores with low capital and reasonable operating costs. As with conventional methods, alkaline cyanide solutions are used for leaching. Since gold (and silver) is (are) present as the native metals, oxygen (as air) is required to oxidatively complex the metals with the cyanide. Oxygen depletion can readily occur adversely affecting recovery. The addition of low levels of hydrogen peroxide during leaching can lead to significant increases in both rate of recovery and total recovery. This process allows for the use of shorter pad times or deeper heaps and increases the gold (silver) concentration to the recovery circuit and thus can reduce cyanide losses by virtue of permitting the use of less total leach solution per ton of ore processed.

Jan 1, 1983

By T. W. Flemal

Good afternoon gentlemen. To begin, may I say ?thank you? to the AIME for the invitation to be here today to talk about my company's experience with shovel, truck, pocket, to car loading. The other author of this paper is here today. (Introduce John Sweet). Before we get to the details of this paper I want to tell you a little about Erie Mining Company. Erie Mining Company is located on the east end of the Mesabi Range in northern Minnesota and is engaged in the business of processing taconite rock into iron ore pellets. In 1970, the twelfth year of production, Erie will produce its rated capacity of 10.3 million tons of high grade iron ore pellets. The plant is the first of five iron ore pelletizing operations managed by Pickands Mather & Co. with a combined annual production capacity of 21 million tons. This plant began producing high grade iron ore pellets in 1957 placing it among the earliest of taconite production facilities in North America. Historically Pickands Mather & Co. had been a leading natural ore mine managing firm in the Great Lakes region for more than 70 years. Pickands Mather & Co. moved into the new field of taconite mining and processing with management and operational experience from the open pits and underground mines. We were to learn much of volume taconite handling requiring new equipment and new procedures. A trial and error period through the early years of taconite processing developed through the operation of an experimental sized preliminary plant near the present Erie Mining Company site.

Jan 1, 1970

By G. M. Wenberg

Bacterial leaching of copper and uranium is practiced in environments containing available sulfur and iron and having a strong acidic reaction. However, many mineral deposits do not have these conditions; the chalcocite and native copper ores in Michigan's Upper Peninsula are examples. Bacterial and fungal populations were observed in samples taken from the White Pine Copper Company tailing pond and mine, and isolates were prepared of the dominant species. The isolates were then screened for solubilization of copper from tailing, ore, and concentrate during incuba¬tion in a carbon and nitrogen supplying medium. Certain Penicillium fungi solubilized significant amounts of copper under neutral to slightly acidic conditions. Leaching apparently was accomplished by release into the medium of metabolites which chelated with the copper.- The process was found to be highly dependent upon the medium and the concentration of copper in the source material. The paper describes sampling and screening techniques, presents the results of experimentation to standardize procedures and maximize the yield of copper, and discusses the nature of the leaching process. This preliminary research reveals a biological process which may find use in mineral extractions but whether it can be applied economically remains to be determined.

Jan 1, 1969

By Rubén Pavón] [H.

Mexico, that for various years held the second place among the elemental sulphur producers in the world, now occupies the fourth position. Nevertheless, taking advantage of the recent increase in the international prices of the metalloid, it is expected that Mexico recovers its traditional position producing, for the first time, over two million tons of sulphur during 1974. Drawing from material stockpiled during the last years sales are expected to reach 2.5 million tons, at excellent prices in the foreign markets, but not so in the domestic ones where prices have remained practically static since 1955, in spite of substantial escalation of production costs. Of the two sources of elemental sulphur in Mexico, the frasch process extraction from the salt domes of the Tehuantepec isthmus where the most important reserves are located - is the one that shall have an important increment. An increase of production of lesser magnitude is expected from sour gas, since sulphur recovery plants wilI go on stream toward the end of the year in the new oil fields recently located in the State of Chiapas. Two Mexican corporations are expanding and improving rational Frasch extraction operations. Together with Petroleos Mexicanos' sulphur recovery from sour gas it is estimated that production during 1975 shall reach 2.5 million tons and, consequently, supply the domestic market and generate an important sum of foreign currencies.

Jan 1, 1974

By William G. Kegel

Apart from a usable product and good 'mining conditions, the greatest asset for a profitable coal mining organization is an effective mine maintenance program. The first step in achieving this is to have good mechanics-or men who want to be mechanics and are interested in knowing more about the design and control of the machines in their charge. A good mechanic's knowledge and ability result from ambition, curiosity, and determination. Starting with these qualities, the aspiring mechanic can launch his career by learning all he can about mechanics, electricity, and hydraulics. Though the path is rough, the end result is rewarding. Mining machinery probably receives as much, if not more, abuse as any other heavy equipment in use today. Considering the conditions under which much of the repair work must be done, it is essential that the mine operator has the best men and tools to perform the work. Mining machines, from their inception, have utilized the electric motor; and down through the years of mechanization, this power source has undergone many changes to better adapt it to the job. The first motors used were direct-current (d-c) motors since d-c power was the most economical power source for mining at the time of early mechanization. These motors were large open-type machines which are seldom used in modern mining. Because of the mine environment, the d-c motor has been reduced in size to better suit the application in mining machines and is now manufactured with dust-tight or explosion-proof enclosures. The d-c motor is constructed with either (or both) series and shunt fields located on the stationary part of the motor (stator) and- an armature coil wound on the rotating part of the motor (rotor). Power is supplied to the armature by brushes which are held stationary and make sliding contact with the armature. The brushes requires regular and careful maintenance because worn or defective brushes will cause heat or arcing which can destroy the motor. D-c motors can be used as d-c generators when mechanical power is supplied to them by the rotating shaft. In the case of a locomotive, this principle is used in dynamic braking. The momentum of the locomotive drives the motor and generates d-c power. The power is regulated with resistors and provides opposition to the motion of the locomotive.

Jan 1, 1981

By Neil D. Donnell, O&apos

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1984

By C. P. Miller

In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about two years ago, approximately ten localities, representing several different types of nickel occurrences were sample, and about 1500 samples of plant and soil were collected. This report will briefly cover the data and results for two areas, and s summary of guides for prospecting.

Jan 1, 1959

By M. G. Gorman

The effects of particle size, particle shape and degree of aggregation on n-dodecylamine flotation of -20 µ m quartz and glass beads were studied. A microflotation cell suitable for use with very fine particles was used in the flotation experimentation. Degree of agglomeration of particles was estimated by comparing size distributions of the quartz and beads in a dispersed system to size distributions in systems in which the collector was present. Results obtained show that in such flotation systems the fine particles are not generally present as individual particles during flotation but rather as aggregations. However, the quartz floats more readily than the beads indicating that there are some shape effects in the systems, considering the large specific surface areas of the materials it also appears that substantial amine consumption in the systems may limit flotation or lead to a requirement of greater reagent dosage for equivalent flotation to that tor larger particles.

Jan 1, 1990

By Joseph D. Martinez

Salt, because of its plasticity, exerts a major influence in deformation. Resulting salt structures are common world-wide. A special type, salt domes, are associated with thick sequences of sediments deposited over salt. Their upward intrusion is generally thought to be in response to buoyancy. Mines in salt domes reveal an internal pattern compatible with large amounts of vertical flowage. Caprock, the end product of accumulation of anhydrite from salt dissolution, attests to long continued upward growth and concomitant truncation by moving underground waters. Concepts of modes of growth are evaluated and related to problems in utilization.

Jan 1, 1979

By I. Orisek

The methodology and results of a feasibility study of an Automatic Truck Dispatching (ATD) system in an actual open pit mining operation, are presented. Using mine cost data, an economic analysis confirms that capital and operating cost savings with ATD out-weigh the costs. Productivity improvement achievable with ATD is quantified with a computer simulation of truck haulage based on mine production and operational data.

Jan 1, 1986

By L. G. Martin

Early mining at Manhattan demonstrated that blasthole assays alone were insufficient to control the disposition of material. A program was began using controlled blasting, intense sampling and panning of crushed samples, fire assay checks, and geologic inspections to sort material in the pits. Statistical data confirms that the method provides effective control at minimal cost. This cost is easily offset by additional tonnage found in areas considered to be waste.

Jan 1, 1980

By James K. A. Harral

The growing national concern over energy has aroused a great deal of interest in the most efficient and least costly way to use our remaining fossil fuel reserves. A number of studies have been published which compare the overall thermal efficiency and cost of gas and electric energy. These studies have been carried out by a wide variety of organizations including Oak Ridge National Laboratory, The Rand Corporation, The Stanford Research Institute, and The Institute of Gas Technology. This paper is an attempt, by PGandE, a large combined gas and electric utility serving most of the northern and parts of central California, to compare the cost and efficiency of gas and electric energy for certain residential appliances using actual operating data and financial statistics for the year 1974, and thereby develop some guidelines for future energy developments utilizing these limited fossil resources. The appliances chosen for the study were kitchen ranges, clothes dryers, hot water and space heaters. These appliances were selected because they can be served with either gas or electricity and they account for approximately one-third of PGandE's total residential electric sales and nearly all of PGandE's residential gas sales.

Jan 1, 1976

By Jerry F. Fountain

Variations in ore grade, mineralogy, and copper pricing structures over the life of the Inspiration mine have mandated many modifications to the treatment methods to maximize process economics. In the 1970's, copper prices generally declined, while inflation, wages, and interest rates increased. A metallurgical treatment route had to be developed for this continuing economic climate which would be capable of minimizing labor, energy, and capital cost requirements. After many years of development, the patented "Ferric Cure" process was introduced to satisfy these requirements. This dump leach process for treatment of mixed oxide/sulfide ore includes: strict mineralogical control of ore placed for leaching, controlled leach pad construction, solution saturation and curing of the pads with higher acid concentrations, and, finally, rinsing of the cured pads for removal of dissolved copper. Leach solutions, high in sulfuric acid during the cure application and low in sulfuric acid during the rinse, contain sufficient ferric iron to enhance the leaching of chalcocitic sulfide minerals.

Jan 1, 1983

By A. M. Raichur

The selective adhesion of hydrophobic Mycobacterium phlei to coal particles is responsible for flocculation of fine coal from associated ash forming minerals. The driving force for the differential adhesion is the hydrophobic interactions between the fatty acid surface of the organism and hydrophobic nature of coal. The effect of Mycobacterium phlei on surface hydrophobicity, surface charge and mechanism of adhesion on coal and associated minerals are controlled by several factors including hydrophobicity and surface and solution chemistry of the system. Adhesion measurements indicate that maximum adhesion occurs below the isoelectric point (IEP) of the coal particles. While massive adhesion of Mycobacterium phlei is observed on coal, however, negligible amount of Mycobacterium phlei attaches to mineral pyrite and quartz.

Jan 1, 1995

By Larry B. Bramlett

Regional radiometric, magnetic and geologic data point to Copper Mountain as an area of general uranium favorability. Sub-regional radiometric and magnetic data direct interest to a specific section of an overthrust Precambrian granite. Detailed magnetic and resistivity surveys in this area show local targets of interest, one of which corresponds to Rocky Mountain Energy's North Canning deposit. On the basis of these data a second and previously untested target was drilled resulting in the intersection of uranium horizons similar to those at North Canning. This integrated geophysical approach can be used for uranium exploration in geologically similar areas.

Jan 1, 1979

By Richard H. Olson

The following discussion will deal with the domestic talc industry only, inasmuch as the writer has had no experience in this field outside of the U. S. This is strictly a geological-mining approach; no attempt is made to assess in depth the effects which milling technology and marketing capability might have in determining the potential of any given talc deposit.

Jan 1, 1970