Search Documents

By R. Q. Honaker

Although the fundamental principles of hindered bed classifiers are relatively simple, the complex interactions between the operating parameters provide a degree of difficulty that hinders the ability for on-line plant optimization. Thus, a dynamic population balance model was developed for determining the hindered settling velocity of particles varying in density and size. The steady-state results of the model include partition curves as a function of particle size and density as well as metallurgical data. A statistical comparison of the simulation results with those obtained from industrial units reveal a high level of accuracy with adjusted R2 values greater than 0.95.

Jan 1, 1999

By Maria C. Jaime

Optimization of the rock cutting performance plays a major role in the tunneling operation. For a given set of tool and cutting environment, rock fragments may be chipped away in numerous manners and it is crucial to understand and be able to predict the dynamics at the cutter-rock interface. This paper presents rational and realistic 3D finite element modeling of rock cutting where typical computational issues ?such as contact formulation, appropriate rock material response, mesh distortion, and crack propagation? are overcome. Cutting forces and failure mechanisms in this finite element analysis are successfully validated by laboratory single-cutter scratching tests in sandstone.

Jan 1, 2010

By K. Adam

Uncontrolled disposal of pyrite wastes and concentrates comprise a major source of acid drainage in active and abandoned sulphide mines. In this paper, the state?of-the-art mitigation measures implemented for the final reclamation and closure of a pyrite concentrate stockpile at Platia Karra, Stratoni mines, Greece, are presented.

Jan 1, 2002

By M. P. Fahey

A significant amount of silca is recovered in the rougher stage of anionic flotation of Florida apatite. This recovery, in the past, has been attributed to both entrainment and cation activated flotation. This study shows that by using a transport factor, it is possible to determine the contribution of each mechanism towards silica recovery. Further, it is shown that the concentration of cations in the conditioning water significantly affects both the amount of silica recovered due to entrainment and true flotation. Further confirmation of this phenomenon was obtained by Ca++ doping of the conditioning water and by using a sodium silicate depressant.

Jan 1, 1996

By W.J. Atkinson

The first recorded discovery of diamonds in Australia was in 1851 from New South Wales. Subsequent prospecting has shown alluvial occurrences of diamond to be relatively widespread through much of the Tasman Fold Belts of Eastern Australia and production to date is estimated to be some 500 000 carats from a number of 'small alluvial fields. Despite extensive exploration though, no primary rock source carrying significant diamond contents has ever been confirmed in Eastern Australia. Conversely, diamond exploration of the older Western and Central Cratons of Australia over the past 30 years has discovered 12 fields containing 360 kimberlites, lamproites and lamprophyric volcanic pipes, dykes and other intrusives, of which 180 have been confirmed to be diamondiferous. Only one pipe however, the 1200 Ma high grade Argyle lamproite and associated near-by alluvials, has proved to be economically exploitable with current annual production of 40 million carats valued at approximately US$400 million. Production from the open-pit will be sustainable until at least 2003. This paper briefly summarizes the history of diamond discovery in Australia, principal diamondiferous provinces and deposits, current exploration activities and the potential for future discoveries.

Jan 1, 1995

By W. M. Aubrey

Cobbing, as used in this; paper, refers to coarse dry magnetics separation. It is applicable when, by its practice, plant cost can be reduced or the value of its products increased by the removal of a barren or lean reject or a high grade final product. This paper attempts to describe cobbing as it is now being practiced, and also the problems that are of concern to the operator and design engineer. In preparation, 16 plants were contacted, all of which were very cooperative with their time and data.

Jan 1, 1958

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By L. F. McHugh

Molybdenum conversion operations discussed in this paper encompass all major operations commercially used to upgrade molybdenite concentrates to various refined products. More emphasis is placed on discussion of key pyrometallurgical unit operations. These operations conducted at Metec include roasting, sublimation, and hydrogen reduction

Jan 1, 1986

By D. A. Shock

Utilizing the technology developed for oil well stimulation by hydrofracing, a disposal system which permanently fixes the waste has been proven. Large quantities of radioactive waste can be processed by a single well system making this method an attractive method for permanent radioactive waste disposal. The system depends on locating a relatively thick formation of impermeable, but easily fracturable rock such as a shale, creating a horizontal fracture, pumping the waste into the fracture in a form which will subsequently solidify and seal the fracture from the well system. The paper presents the theoretical considerations from creating and extending horizontal fractures and how these considerations were used in designing a waste disposal system which is now operating.

Jan 1, 1964

The paper presents results of the mineralogical examination on samples from a bacterial leaching test which simulated in situ leaching for 482 days. Rock fragments (15 to 20 cm) were obtained from the top, the middle and the bottom of a bioleach column. Examination of the samples was carried by electron microscopy and image analysis. The surfaces of the rock fragments were studied to characterize the precipitation products, and cross-section cuts were studied to assess the advance of the bacteria leaching front and the dissolution of the different sulphide minerals.

Jan 1, 1991

By D. L. Kowal, P. J. Whittaker, M. A. Tuzun, N. O. Lotter

The area of flotation testing of drill-core is important in the business plan of most mining companies. Metallurgical information derived from this practice can be used to advantage in strategic decision-making. Sampling, flotation testing and subsequent Qem SCAN analysis of a mineral resource is one example of this approach. Anew resource, located in Sudbury, Ontario, is being assessed for the Sudbury Operations of Falconbridge Limited, which includes the Strathcona Mill. In this case, it was possible to improve the value of information from sampling and flotation testwork by using an improved, statistically-based test design, by sampling the resource by generic end-member ore type, and by integrating the Mineral Processing and Mineral Science disciplines into a Process Mineralogy team. In addition to producing standard metal grade and recovery information, this new approach provides more reproducible information from representative samples and flotation testing in a replicate format. Qem SCAN technology is used to produce a size by size mineral balance, including both modal percentages and liberation, from which flotation models for each ore type can be developed. As a result, a key understanding of the potential behaviour of a given ore type, if mined and then processed at the current mill operation, is gained at the 95%confidence level. The three ore types of this mineral resource were shown to have different flotation characteristics. Quantifying the mineralogy and liberation in each of the three ore types, has shown that this difference is due to changes in modal percentages of ferro-magnesium and magnesium silicate minerals such as pyroxene, talc and serpentine. Liberation across the three ore types is very similar and is therefore not responsible for variation in flotation performance.

Jan 1, 2003

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By Stephen J. Crittenden

Deep gas and oil production has been substantially increased over prolonged periods through the use of sintered bauxite propping agents. Since its inception in 1976, over 170,000,000 pounds of high strength ceramic proppants have been employed. Recent field evaluations and economic analysis demonstrate the superiority of sintered bauxite proppant over quartz sand. This paper describes the development, application, field results, and product evolution of sintered bauxite.

Jan 1, 1983

By Malcolm Heyburn

Airborne and ground magnetic surveys were made over and in the vicinity of the Sanford Hill ore body at Tahawus, Essex County, New York. These geophysical surveys served to: l. delineate, lithologic and structural features associated with the ore bodies; 2. indicate a major extension of the Sanford Hill ore body; and 3. guide a drilling program to prove this extension. The titaniferous magnetite ore body at Sanford Hill is associated with gabbro occurring in anorthosite. The contrast in the magnetic susceptibilities of these rock types, reflected in the magnetic measurements, allows geologic-mapping showing rock types and inferred structural features. The anomalous magnetic high of the airborne magnetometer survey indicated a southern extension of the Sanford Hill ore body. Diamond drilling, guided by the airborne and specifically the ground magnetic results, substantiated this interpreted ore extension to be of major magnitude.

Jan 1, 1961

By D. Wright, J. Samborski

DuPont’s Florida Plant has been mining in northeast Florida and supplying titanium-bearing minerals, zircon and staurolite for over 50years.The site has successfully implemented and “sustained” a land reclamation/habitat enhancement program that goes beyond regulatory requirements and standard industry practices. However, the term sustainability has been used by so many organizations, many with divergent viewpoints, that it is important for a mine to develop its over-all concept and approach to sustainable operation. As a foundation, the outstanding reclamation efforts at DuPont’s mine will be presented followed by a broader look at the overall sustainability strategies and tactics used at the site.

Jan 1, 2004

By George D. Lessner

I'm sure that everyone at this meeting is aware of the current problems facing the U.S. metals mining industry. Prices are depressed and expected to remain depressed for quite some time. On the other hand, industrial minerals, including talc, are doing quite well. The profitability of industrial minerals has sparked considerable interest on the part of many companies in expanding into industrial minerals. Our company is one of those actively seeking to expand its position in industrial minerals. It is appropriate that the A.I.M.E. asked me to speak to you regarding entry into the talc business. So how do you get into the talc business? Earlier speakers have explained how to locate, mine, process, and market talc, so you have the "how ton.

Jan 1, 1984

By Michael Deutscher, Jozef F. Zurawski

Part of Capital Improvement Project SE-754 tendered by New York City Department of Design and Construction included installation of a 96-in. (2.47 m)diameter sewer by pipe jacking methods. The pipe selected by the Contractor, EIC Associates, Newark, New Jersey, was a glass-fiber-reinforced thermosetting resin pipe installed in two reaches: 72 m (235-ft.) and 222 m (728-ft.). The machine selected for the excavation was an open face shield. This paper describes the set up of the tunneling operations, subsurface conditions, progress of excavation, pipe performance and other details of the project including unexpected difficult ground conditions that were encountered during excavation and how these conditions were overcome.

Jan 1, 2003

By Moussa Wone, V. Nasri, F. Guimbal, D. Andre

The Magenta underground station was constructed in the heart of Paris in saturated soft soil and at shallow depth. To investigate the surface settlement and the deformation of the concrete liner, innovative techniques combined with a vast campaign of monitoring were applied. The monitoring data and a simple three-dimensional ?nite element analysis were used to assess the accuracy of the two-dimensional ?nite element model originally utilized in the design of the station. The deformation of the concrete liner was monitored using vibrating wire extensometers. Their performance was validated by the data obtained from monitoring and also by a simpli?ed ?nite element analysis.

Jan 1, 2003

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the "advance and relieve" method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2001

By Allan M. Johnson

Since 1974 researchers at Michigan Technological University have been studying mine subsidence in the Iron River District of Northern Michigan. The district, which was active from 1881-1978, has had numerous cases of subsidence. Much of the subsidence resulted from rock mass failure but some appeared to have developed primarily in the thick glacial overburden which is a typical feature of this area. This latter observation led to the recognition that some of the surface subsidence was due to piping; i .e., loss of overburden material to the mine voids by groundwater flow (Johnson and Frantti, 1978). The Sherwood Mine was the last mine to operate in the district. With its closedown scheduled for late summer of 1978, a unique opportunity to monitor the mine as it flooded was presented. It was reasoned that with the cessation of pumping, groundwater would rise in the overburden and the mine would flood. The physical characteristics of the mine were favorable for piping to occur as the mine flooded. With the permission of Inland Steel Mining Company and the support of the U. S. Bureau of Mines, a project to monitor the Sherwood Mine for piping subsidence began in June of 1978. This paper present aspects of this study pertinent to the piping-induced subsidence events which occurred at the Sherwood Mine in 1980 and 1981, including acoustic emission monitoring of the subsidence activity, hydrologic monitoring of the groundwater regime and the flooding mine, laboratory modeling of the piping mechanism, and analytic procedures which are under development.

Jan 1, 1982