Search Documents

By G. R. Corbett

The introduction of roof bolts to Phalen Colliery in the Sydney Coalfield, Nova Scotia (annual output of 2Mt) has been successfully implemented in maingate and tailgate entries over the last four years. Monitoring of the roof bolted areas continues to be an integral part of the quality control program as the results are utilized to maintain safety and to aid in long-term design strategies. Although all gateroads in the Phalen Colliery have converted to roof bolts as their primary means of support, the majority of intersections which intersect the main slopes remain supported by large steel structures. Several intersections within the Phalen Colliery were monitored as they were created by the mining process. A comparison is made between intersections supported with only traditional 6.4 to 6.7 m steel structure and intersections supported by 2.44 m fully resin encapsulated roof bolts in conjunction with 7.6 m fully cement grouted cable bolts. Detailed monitoring was conducted using CA NM ET's intrinsically safe sonic probe extensometer datalogger which has the ability to read up to sixteen probes simultaneously at programmed intervals. The density of the data from the datalogger has allowed a better understanding of the deformation of cable bolted intersections than was possible with manual monitoring. Test results have helped mine operators to design safer cable bolted intersections.

Jan 1, 1995

By John A. Owsiany

The effect of longwall mining on streams and shallow aquifers has been the subject of numerous research studies for more than twenty years. As a result of these studies, it has become common to consider an overburden thickness of 400 feet as the lower limit at which longwall mining methods may be used with little or no effect on hydrologic systems. This paper presents the results of a study documenting the response of a large high order stream to shallow cover undermining by longwall methods in the northern Appalachian coalfield. The field site is located in a narrow stream valley where the overburden, composed primarily of limestone and sandstone units interbedded with shales and siltstones, ranges in thickness from 340 to 285 feet above the main bench of the Pittsburgh coal seam. Streamflow monitoring and monitor well measurements indicate that no significant loss zones or water table lowering resulted from undermining the stream or the adjacent valley bottom area. Additionally, hydrographs for shallow near-stream wells exhibit fluctuations related to natural seasonal variations, which are nearly identical to those observed in a non-undermined control well in the same watershed. Environmental factors affecting streamflow were monitored through the use of a control stream in an adjacent non-undermined watershed to differentiate between natural and mining induced changes in flow.

Jan 1, 2001

By Mike Watts

Since the first longwall panel development started in the new mining, (Southern) area, a number of roof falls have occurred in L1 and L2 gate-entries. The longwall was delayed for a total of two months due to roof falls in the gate-entries. To prevent roof falls in future gate-entries, an extensive ground control analysis has been conducted which incorporated regional horizontal stress and panel orientation, tectonic stress, roof strata, surface stream valleys, etc. Results of the analysis indicate that a combination of these factors caused the roof falls. Therefore, a Roof Instability Rating (RIR) system was constructed to predict the roof condition and identify areas where supplemental support should be implemented. The L3 gate-entries, supported by the prediction using the RIR system, have not experienced any roof problems.

Jan 1, 2000

By John D. VandeKraats

Yielding rock bolt support systems have been developed to accommodate ground movement in shifting ground such as in coal operations; in creeping ground such as salt, trona, and potash; and in swelling ground associated with some clays. These systems, designed to remain intact despite ground movement, should enhance mine safety and help contain costs in areas where rebolting of rigid non-yielding systems is typically required. Four such systems were tested in straight tensile pulls in the laboratory. They include the Slip Nut System from Dywidag Systems International USA, Inc., Ischebeck's bolt mounted Titan Load Indicator, Rocky Mountain Bolt Company's Yielding Cable Bolt, and a rock bolt installed variation of the yielding steel post developed by RE/SPEC Inc. The first two systems are currently marketed products and the latter two are prototype systems. Each system responds to load and displacement by yielding in a unique manner. All are designed to yield at predetermined loads. A description of each system and its yield function is provided. Each system was tested over its prescribed yield range in a test machine. At least five tests were performed on each system. Each system yielded and continued to provide support according to its design. Each shows promise for ground control use in shifting or creeping rock. This work helps to illustrate the comparative differences in performance between these specialized systems and the applications where they may be most useful.

Jan 1, 1996

By Hamid Maleki

A comprehensive study consisting of stress determinations, core logging, laboratory testing, and numerical analyses was conducted to investigate the cause and potential alternatives to the coal bump conditions that developed in the Second North Panel of the Little Dove mine near Buntington, Utah. Roof rock characteristics were such that a cave did not develop above this 420 ft wide panel. After 700 ft of pillar retreat, severe coal bump conditions developed during pillar mining. The coal bump conditions resulted from excessive pillar stress which was caused by load transfer from the extracted, noncaving, portion of the panel. Site specific data and numerical modeling techniques were used to back-analyze the bump prone condition. This back- analysis lead to the identification of critical stress, closure, and energy release levels. These critical levels were then used to evaluate alternative pillar mining sequences in the hope that the potential for coal bumps could be reduced. It was found that while alternative sequences offered some potential improvement over the pillar mining sequence used in the mine, alternative pillar mining sequences would not significantly reduce the potential for bumps. For the roof characteristics at this mine, coal bumps are best avoided by developing narrow panels or significantly wider panels, which incorporate properly sized barrier pillars. Narrow panels, on the order of 300 ft, would not cave, but panel pillar stresses and the potential for umps would be moderated by the reduced r' panel width. Wider panels, of approximately 650 ft, would allow a cave to develop, also reducing panel pillar stresses and coal bump potential.

Jan 1, 1987

By Kot F. Unrug

In the premining stage of engineering design, the only available data are obtained from core drilling. It is often not sufficient for a realistic design of strata control. During the development, an access to the geological formation is created, enabling in situ testing. Obtained data can be utilized accordingly to improve preliminary design. The available methods for testing are described with emphasis on their application for a longwall system. The optimum design ensuring continuous operation of the high output longwalls is critical because their downtime is very expensive. Optimization of ground control measures also has the potential for substantial savings by elimination of unnecessary support.

Jan 1, 1994

By Erdal Ünal

The computer program introduced in this paper is based on design guidelines developed for selection of support systems used in mine roadways. The support types considered include rock bolts as well as rigid and yieldable steel arches. Using the computer program, the design engineer can select the type, pattern and specifications of the support systems suitable for various roof conditions. The concepts utilized, assumptions made, support selection criteria and description of the computer program, developed for the PC, are included.

Jan 1, 1989

By John W. Fredland

Many accidents occur in the mining industry as a result of the instability of material during handling and processing operations. Accidents due to dump point instability at stockpiles, and at spoil or waste piles, for example, occur with alarming frequency. Miners must be trained to be better aware of these hazards. Information on safe working procedures at stockpiles and surge piles is provided. Mine operators must review their training and operating procedures regularly to ensure that hazardous conditions are avoided.

Jan 1, 1993

By David A. Newman

Barrier pillars created during mine development provide additional reserves during mine closure and can be the sole access to reserves previously abandoned because of mining height or out of seam dilution limitations. The safe and successful mining of barrier pillars requires a thorough knowledge of the magnitude and distribution of the vertical stress field in addition to the strength and physical properties of the coal, immediate roof, and immediate floor strata. Quantifying the vertical stress field is complicated by the combination of the overburden stress, abutment stresses transferred onto the barrier pillar from adjacent gob areas, and in multiple seam mining, stresses transferred from abandoned subjacent mines. These variables make the extraction and development of barrier pillar reserves a site specific consideration. Three case histories are presented in which barrier pillar development and extraction provides; i) an access point and the means to ventilate a large area of low seam reserves left by a prior operator after developing only the thicker areas of a multiple split reserve, ii) the means to increase total recovery of a deep, thick seam longwall reserve, and iii) opportunities for the development and retreat mining of a two mile long barrier pillar in thick seam reserves.

Jan 1, 1995

By Robert A. Siokler

Approximately 75 percentage of the earth's land surface is comprised of shale or shale-like materials. Shale itself is composed of the residue from an almost infinite variety of weathered parent materials which have undergone deformations ranging from intense to negligible. Under standard test procedures, shales exhibit a very wide range of physical properties particularly if the test specimen is subjected to a change in moisture content, when the original test values may vary from 0 to 100 percentage. It is this wide variation in physical property values compounded by its ubiquitous presence that makes shale such a problem material to engineers. In reviewing the literature relating to shale, it is evident that the "problem" has been approached from many directions. In order to understand why shales behave as they do, investigators have sought mineralogical, geological, chemical, electrical, and physical answers. Each study yields valuable academic information, but few contribute much of value to the engineer in the field. Many valid relationships between shale strength or competency and clay type, clay content, organic content, water content, grain size, cementation, density, porosity, etc, have been established. Yet it is very difficult to extend these understandings to the in situ condition with results that can be used by the field engineer. One major reason earlier work has not produced better information lies in the ambiguity of the definition of shale. It is apparent that no one laboratory parameter can be successfully used to provide sufficient engineering information to properly describe in situ conditions. For example; shale with swelling clays will produce low strength values provided: the swelling clay is in sufficient quantity, the clay is dispersed throughout the medium involved, and there is a low value of cementation. Shales with high unconfined compressive strengths have been found with very low shear strengths. Sandy shales often provide as many ground control problems as clay shales. Shales of similar nature may provide good roof conditions in one part of a mine yet in another part of the same mine the apparently identical shale may cause substantial problems. A clear need exists to classify shale in a manner which will enable the engineer to better predict the strength and durability of shale-like materials. Studies at the University of Missouri-Rolla (UMR) have focused on finding parameters which influence durability and competency, while being discretely discernible through uncomplicated testing. Initial research concentrated on distinguishing shale8 on the basis of standard physical tests such as: unconfirmed compression, triaxial shear, and slake durability. As results accumulated, however, it became evident that moisture content played a much greater role in determining competency than had been recognized previously. As a result the focus of the research turned to developing tests which would evaluate the influence of moisture on shale behavior. The above work then became a foundation for a second phase of investigation in which a suite of standardized tests were developed to provide a classification procedure. From this study five tests were identified as being critical: Moisture Activity, Atterberg Limits, Submersion, Unconfined Compression, and Shore Hardness.

Jan 1, 1986

By D. A. Donato

It is often necessary for a mining company to extract coal from a seam underlying a previously mined coal seam. The impact of the overlying mine workings on the stress distribution within the underlying mine workings is very difficult to assess without the use of numerical modeling techniques. This paper demonstrates the usefulness of applying numerical modeling to evaluate alternate startup-room locations for a longwall panel considering the effects of multiple seam interaction. MULSIMIPC, a code adapted by the former U. S. Bureau of Mines, was used to compare stress patterns in two proposed startup-room locations. These model results were not only compared to each other, but also to results from a model with no overlying mine workings to provide baseline criteria for evaluation of the two proposed startup-room locations. The numerical modeling study was successful in providing useful information to the coal company and the regulatory agency (MSHA), resulting in a mine design that was both safe and efficient, and prevented the sterilization of a large volume of coal reserves.

Jan 1, 1996

By Wm. Mark Hart

High horizontal stresses and shear failure have been considered the major reasons that cause entry roof failure and falls for underground mining. Therefore, reorientation of the current mining systems or layouts or using angular crosscuts in mains or gate entries becomes more popular if a greater than normal horizontal stress is measured. However, reorientation of the current mining systems or layouts is always expensive and use of the angular crosscuts may weaken the pillar structure at corners. Therefore, cautions must be taken before any decision related to reorientation of the current mining systems or layouts or use of angular crosscuts is going to be made. In order to prevent entry roof failure and falls, the following two issues must be carefully examined and fully understood: 1. Which one, shear stress or tensile stress, is going to be blamed for entry roof failure? 2. Which one, horizontal stress, vertical stress, or local geological weakness plays a major role in entry roof failure and falls? This paper analyzes the mechanisms of entry roof failure and falls for underground mining in general examines the roof fall history at Springvale Colliery, and proposes the means of preventing roof failure and controlling roof falls for Spingvale Colliery in particular.

Jan 1, 1996

By Kenneth E. Hay

Researchers from the U.S. Bureau of Mines conducted a field study to assess the safety of remotely controlled mobile roof supports (MRS) in a retreat pillar mining operation, Data were collected to provide the Mine Health and Safety Administration with criteria needed to develop guidelines for MRS use and to determine if precursors could be identified that would alert miners to imminent roof falls. Two test sites at which two different support methods-MRS's and posts were used and were monitored to obtain information on entry stability. Pressure transducers and string pots were installed on all four MRS's to obtain loading and displacement information. and roof bolt load cells. sonic probes, extensometers, and survey targets were installed in the surrounding entries to obtain information on ground behavior. Results showed a larger increase in roof bolt loading and roof movement when MRS's were used, especially in the intersection area. Roof bolt loads in the entries showed decreases in load when the MRS's were set and increases up to 11,1 kN (2,500 lbf) when the MRS's were unloaded. Unloading of one MRS in a pair did not significantly increase load on the other. MRS's I and 2 usually had the higher loads, with these loads increasing as the pillars on each side were being mined. MRS 3 normally had lower loads than I and 2: however, it also experienced some very high loads when in the last position near the pushout. MRS 4 usually had the lowest loads, primarily because it was located near the solid pillar that was not being mined.

Jan 1, 1995

By G. C. Marino

The performance of the V-Day Mine near Danville, Illinois has been evaluated from data extending over about a 20 year period. The area included in this study involves over 16 acres. Essentially this entire area has progressively subsided. Extensive data has been collected on the geologic and mining conditions, the subsidence movements, as well as on the response of the surface structures to the subsidence. In this paper a detailed summary of the site conditions is given, and the mechanics of progressive failure of the studied room and pillar mine is postulated. These progressive long-term failures of the V-Day are then compared to other similar mine failures in Illinois. Some overall, but tentative, long-term strength evaluations are presented as well.

Jan 1, 1990

By I. W. Farmer

Weightings and water inflows into longwall workings often occur together, giving rise to discussions on their relative genesis. Case histories are introduced which indicate that most water inflows are associated with heavy weightings. Resultant large releases of energy can lead to extensive vertical fractures, which can drain water from aquifers or other sources, such as separation accumulations, onto the face. Effectively control of water inflows in these cases depends on face support and weighting control.

Jan 1, 1996

By Christopher Mark

The Bureau of Mines has recently completed a comprehensive study of coal strength. More than 4000 individual test results from over 60 seams were extracted from the literature and combined in the most complete data base of the uniaxial compressive strength of coal ever assembled. In addition, more than 100 case studies of in-mine pillar performance were available in the Analysis of Retreat Mining Pillar Stability (ARMPS) data base. Statistical analysis of this wealth of data has yielded valuable results. The data shows clearly that the "size effect" is related to coal structure. The widely-used Gaddy formula, which predicts a significant strength reduction as the specimen size is increased, was found to apply only to "blocky" coals. For friable coals, the size effect was much less pronounced or even non-existent. Case histories of failed pillars are the best available data on in situ coal strength. This study found no correlation between the ARMPS stability factor of failed pillars and coal specimen strength. Pillar design was much more reliable when a uniform coal strength was used in all case histories.

Jan 1, 1996

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard to miners and mine operators. This type of failure, termed a "Cascading Pillar Failure" (CPF), occurs when one pillar in a mine layout fails transfering its load to neighboring pillars causing them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S. are documented. Mining engineers can limit the danger posed by these failures through improved mine design practices. Whether failure occurs in a slow, nonviolent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines, namely, the containment approach, the prevention approach, and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining.

Jan 1, 1996

By C. Fairhurst

Most of the papers designated as being within the topic of underground storage at this Symposium are concerned with aspects of radioactive waste isolation. Although this is, unquestionably, an important international application of underground storage, and one involving a considerable number of research investigations, the subject of underground storage is indeed much broader. Several major international conferences have been devoted exclusively to it. Applications include storage, under a range of temperatures and pressures, of oil and liquefied petroleum products, compressed air, heat, foodstuffs of various kinds, hazardous and 'nuisance' industrial by-products, and a variety of special applications, both civilian and military - some in use, others proposed. Storage may be in caverns excavated specifically for the purpose, exhausted mines may be adapted for storage or, in some cases, the material to be stored may be injected under pressure into the pore spaces of porous-permeable formations at depth. A variety of rock types and geological environments are used, e.g. excavations in salted or domal salt, where long-term creep closure of the openings is a concern; massive granite, where fluid loss through fissures may be important. Cavities may have spans of several tens of meters, and there is interest in achieving still larger excavations. As would be expected, this breadth of underground storage applications introduces a similarly broad range of questions in rock mechanics and rock engineering. The report will review these questions and recent developments in rock mechanics research, computational procedures, and design applications - and will also discuss the opportunities for a still greater range of applications of underground storage to current industrial and social problems.

Jan 1, 1989

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996