Search Documents

By Ihsan Berk Tulu

In the Analysis of Retreat Mining Pillar Stability (ARMPS) program, the magnitude of the abutment loading adjacent to a gob area is calculated using an ?abutment angle? concept. The extent of the abutment loading is determined solely as a function of depth from an empirically derived equation. In the recommended calibration method for LaModel, it was believed that the empirical equations for calculating the magnitude and extent of the abutment load, as used in ARMPS, were the best available methods for determining these critical overburden loading values. Therefore, similar calculations were implemented in the LaModel calibration method. However, the latest in situ stress measurements of abutment loading performed in the United States and Australia have shown that there can be significant deviations in the measured abutment magnitude and extent as compared to the predicted values from the empirical formulas used in ARMPS and LaModel. It seems reasonable that the overburden geology, depth, extraction panel width, and mining height should have a significant effect on the extent and magnitude of the abutment load. However, the current empirical formulas do not incorporate many of these significant parameters into determining the abutment load on the pillars. In this paper, stress measurements from US and Australian mines were back-analyzed by using analytical and numerical methods to investigate the measured abutment extent and loading. Ultimately, it was determined that the original empirical abutment extent formula in conjunction with the original ALPS square-decay stress distribution function was supported by the case histories in this paper. Also, for depths less than 900 ft, the average 21° abutment angle was supported by the case histories; however, at depths greater than 900 ft, the abutment angle was found to be significantly less than 21° and should be calculated with a new proposed equation.

Jan 1, 2012

By James J. Scott

Dynamic rock anchors are interior fixtures developed by the author which promise to be a revolutionary development in the field of ground control. The fixtures are designed to be placed in the ground with modern roof bolting equipment, such as the type used in the American coal mining industry. They are composed of a plastic form- able anchor tube which serves to fasten a buttress deformed rod which is thrust and turned into the plastic and in turn clamps the roof plate to the rock surface. Plastic tubes 10 to 16 inches in length provide sufficient anchorage to exceed the yield strength of steel rods 5/8, 3/4 or' 7/8 inches in diameter. This paper presents field testing and early work done on the device over the last seven years. Results of pull tests, creep tests, laboratory testing in concrete, and field testing under natural rock conditions demonstrate the uniqueness and effectiveness of this new support system. A second development which uses the dynamic rock anchor in conjunction with a resin cartridge to provide a stiffer anchorage system is also discussed. These products will be manufactured and marketed by Ingerso-11-Rand Co. under the trademark of DYNA-ROK and DYNA-ROK PLUS anchors.

Jan 1, 1989

By Najdat I. Aziz

There are different schools of thoughts about the influence of gas pressure on coal strength. Researchers have reached contradictory results with regard to the effect of confining gas pressure on tensile strength of coal. Accordingly, this paper re-examines the influence of gas pressure on the strength of coal. A specially designed precision drill capable of drilling in a pressurised chamber was used to drill coal samples under both atmospheric and increased gas pressure environment. The drill cuttings were examined for particle size distribution using a laser controlled Malvern Mastersizer S particle size analyser. Petrographic analysis of the sample examined the effect of gas pressures on the maceral structure and the composition of coal. The paper demonstrates that there is a definite variation in the range of particle size distribution with particles obtained from drilling coal samples not subjected to gas pressures, in comparison with those obtained from samples drilled under confined gas pressure. Also observed were the changes in the rate of drilling in soft coal obtained from geologically-disturbed zones compared with other coal samples. Some variation on the maceral compostion of coals were also observed in relation to increased gas pressures and gas type.

Jan 1, 1996

By Andreas Hucke

For the roadway design in the German hard coal mining industry, an advanced combined planning system has been applied during the past 20 years. The German mining industry is working with single entry roadways system. After first longwall passage the roadways will be stabilised with side wall building material packages. Later this roadway will be used again for the second retreating longwall. The intention of the implementation of several different design methods for the planning of the roadways is to enhance the reliability of the results. On one hand the planning system uses numerical simulation and physical modelling in addition to analytical and empirical methods. On the other hand in-situ monitoring and analysis during the roadway development will be used to verify and calibrate the numerical and physical models. Especially before the implementation of new support elements in underground, this system is suitable and reasonable because the new support elements will be tested in the physical and numerical simulation prior to cost intensive underground tests. The interaction between the numerical and physical modelling in comparison with underground monitoring and analysis during development and the later use of roadways will be shown with some examples. The first example shows a rock bolted rectangular roadway which will be mined at both sides of the roadway. Different support and roadway building material package systems are investigated under various stress conditions. The results are utilised to optimise the roadway support and the roadway side package systems. The influence of different points in time of the installation of several support elements in a combined arch and bolted roadway is shown as another example. Two different types of support systems are compared within the physical models. These models are used as a base for ongoing numerical analysis and simulation to find out the ideal point of time to assemble the different support elements. The last example handles the influence of slickensides in the roof of arch shaped roadway on their stability. Different slickenside positions and densities are investigated and classified.

Jan 1, 2006

Recent improvements are described in several techniques for ground control in underground mining. Promising methods for analysis and mitigation of rockbursts are discussed. Methods of assessing damage to underground excavations from repetitive seismic loading are reviewed. Analysis of mining-induced surface subsidence is discussed.

Jan 1, 1989

By Keith A. Heasley

In the past, numerous displacement-discontinuity (DD) models of stratified rock masses have been proposed using a homogeneous isotropic elastic overburden. In this paper, it is postulated that a laminated overburden model might be more accurate for describing the displacements and stress in these stratified deposits. In order to investigate the utility of using a laminated overburden in a DD model, the fundamental mathematical basis of the laminated model is presented and graphically compared with the fundamental behavior of homogeneous isotropic elastic overburden and with field data. Specifically, the stresses and displacements surrounding an idealized longwall panel as determined from the laminated overburden model are presented and compared with results from the homogeneous isotropic overburden and with measured abutment stress data. Also, the remote displacements and surface subsidence as calculated by the laminated overburden model are compared with homogeneous isotropic calculations and with measured subsidence data. The results of this investigation show that the laminated overburden is more supple, apt to propagate displacements and stress further, and better able to fit observed data than the classic homogeneous isotropic overburden. Ultimately, it is suggested that the laminated model has the potential to increase the accuracy of displacement and stress calculations for a variety of mining situations.

Jan 1, 1996

By Stephen Tadolini

The annulus thickness, for bolts anchored with resin, effects the systems final performance. Recent developments in the manufacturing process of these support systems, coupled with improved resin characteristics, have resulted in design changes to minimize hole drilling requirements and reduce resin usage. The amount of resin to properly anchor a 7/8-SRD (Special Rolled Dimensions) bolt in a 25.4 mm (1-in) diameter hole has been reduced to about one-third of the resin required to anchor a No. 7 rebar bolt (22 mm (7/8-in) diameter) traditionally installed in a 35 mm (1-3/8-in) diameter borehole. More importantly, laboratory and field tests, indicate that higher bond strengths and anchorage capacities can be realized with reduced annulus systems. These factors have a direct bearing on reinforcement efficiency and subsequent roof support performance.

Jan 1, 1998

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

By Jeffrey M. Listak

This report describes a study, conducted jointly by BethEnergy Mines Inc. and the Bureau of Mines, to assess the effects of longwall front abutment loading on various supplemental support materials utilized in a predriven recovery room. The purpose of the predriven recovery room is to reduce longwall equipment transfer time by eliminating the premove preparation associated with conventional recovery methods. In addition, the room provides a large area in which face salvage equipment can maneuver. Results of four recovery-room study areas show the progression and influence of the front abutment on the longwall panel and supports and their subsequent behavior. The best performance (i. e. the support that most facilitated recovery) of support material was achieved through the use of a concrete mixture which had a sand content of 35 percent by volume. The longwall transfer time was reduced by 30 percent which translates to a production advantage of 37,000 raw tons of coal per panel.

Jan 1, 1989

By Hamid Maleki

Having developed a methodology for estimating mining-induced seismicity resulting from slip along geological discontinuities in 2003, in this paper, the importance of measurements are high-lighted in the study of caving and seismic source mechanisms as applied to mine designs. Geotechnical data is analyzed from four case studies to address cave condition, load transfer, and potential effects on stability and resource recovery in four Utah mines using measurements and observations conducted over the last three decades. Cave conditions are evaluated on the basis of measurements in the gob of a western U.S. operation mining under the massive Castlegate Sandstone and indirectly using the results of measurements and boundary-element modeling at panel boundaries at a mine where strata behave elastically. Together with subsidence measurements and microseismic monitoring, regional caving and load transfer in multiple-panel extractions are addressed while the effectiveness of barrier pillars in reducing stress and seismic response where mining under massive stratigraphic units is analyzed using measurements and three-dimensional computer modeling.

Jan 1, 2006

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

By Kausik M. Sinha

Hydraulic stowing, which is being practiced in several major coal producing countries to deal with adverse mining conditions, usually permits almost 100% coal recovery from underground mines with minimal and controlled surface subsidence. It can be implemented in the US coal mines to reduce the severe effect of land subsidence and at the same time improve the cost of coal production, both of which are major setbacks for the coal industry in the USA

Jan 1, 1989

By Yingxin Zhou

Virtually every coal seam in Appalachia will at some time be subject to multi-seam interaction (Wu et al, 1987). Many such problems result from seams which lie in close proximity or have split and lie within thirty feet vertically of one another. Existing techniques for multi- seam design have concentrated on conditions where the entire inner burden is not the failing member and are unsuitable for ultra-close multi-seam design. Structural integrity of the inner burden must be maintained if two superimposed seams are to be mined separately and under- standing possible failure mechanisms of the inner burden is an essential first step in the design process.

Jan 1, 1989

By M. J. Beus

This paper will describe the research approach being initiated by the Spokane Research Center to assess hazards and design criteria to prevent ground and muck falls in and around ore passes in hard-rock mines. The major goal of this research is to compile detailed information about ore pass processes and hazards, identification and testing of prevention strategies, and development of computer-based measurement and design methods. Recent ore pass failures have underlined the lack of OE pass design capabilities and standards available to both mine engineers and MSHA personnel. Design criteria and ore pass hang-up prevention and remediation strategies will include the effects of internal ore pass loads, blasting to relieve hang-ups, and rock mass stress redistribution and structural interaction from nearby mining. New visualization and three- dimensional analysis methods will be presented as an extension of existing ore pass design and analysis techniques. A sophisticated particle-flow analysis program will be used to simulate the response of various ore pass designs to a wide range of loading conditions driven by rock mass deformation, muck flow, ore pass blockage, and blasting in both nearby stopes and the ore pass. Analysis techniques will be calibrated and design criteria validated at the Spokane ore pass test facility. These tools will serve to reduce research costs by limiting the number of experimental field tests required.

Jan 1, 1996

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007

By L. R. Stace

Arguably, one of the most significant technological breakthroughs that had been experienced during the period when British Coal was the major coalmine operating company in the UK, the use of rockbolts as principal support in underground roadways brought with it the need to re-assess the technical knowledge, management controls and legislative frameworks associated with the support of mine workings. Following a major roof fall in a roadway supported principally using rockbolts in which fatalities occurred, the process of the design of rockbolted support and the systems and procedures that had been put in place to control its use in the UK were further reviewed. The paper discusses the outcome of these reviews, and how the incident initiated a major new interest in strata control research in the UK against the background of the fragmentation of the ownership of the mines following the sale of the former British Coal assets at the end of 1994, together with the proposed introduction of new strata control legislation in 1996.

Jan 1, 1996

By Christopher Mark

A coal burst is defined as the sudden, violent ejection of coal or rock into a mine opening. Coal mines in the North Fork Valley (NFV) of Colorado?s Gunnison River have a long history of coal bursts in a wide variety of settings. These have included longwall and room-and-pillar, development and retreat, and single- and multiple-seam mining. In contrast to other coalfields, where bursts are typically associated with strong, massive sandstone and extremely high stress, many bursts in the NFV have occurred beneath shale roof and some distance from the most highly stressed locations. The goal of this paper is to attempt a systematic study of the entire burst history in the NFV, in order to gain insight into their characteristics and causes. The primary sources of information are the reports of investigations conducted by the Mine Safety and Health Administration (MSHA) Roof Control Division over the past 15 years. This paper provides details on the geologic mapping conducted as part of these investigations, as well as a regional plot of burst locations using a Geographic Information System. The mapping indicates that many of the NFV bursts have been associated with structural features, including low-angled faults and well-defined zones of high-density jointing that exhibit little or no displacement. Some of these features appear to extend for several miles, impacting more than one mine.

Jan 1, 2012

By Wenbing Xie

At Renlou Coal Mine, Huaibei Mine Area, the track entry deformed significantly after longwall mining in an overlying multiple seams. The supporting characteristics of primary roof bolts and shotcrete with wire mesh are closely related to the movement of the mine?s surrounding strata. A case study of a track entry deformation was monitored during the longwall mining of a selected overlying panel. The measured data showed the unique entry deformation pattern during the longwall mining in the overlying seam. Underground extensometer measurement showed that entry stability was mainly affected by the periodic roof weighting of longwall mining in the overlying seam. The displacement of the deeper strata occurred a head of the immediate vicinity of the entry. Thereafter, deformation of the roof and floor strata was in the form of shearing of the shallower strata. Due to the use of heavy-duty roof bolting with wire-mesh, the roof-tofloor and rib-to-rib convergences were small, but the floor heave was large, greater than 80% of the roof-to-floor convergence. The measured displacement from extensometers varied with the position of the monitored cross-sections and depth into the roof. There were several deformation patterns, such as shearing movement, compression, and expansion, and the variations between compression and expansion. Strata compression at the entry surface was always accompanied with shearing movement at the deeper strata. During the longwall mining, the whole surrounding strata of the entry moved toward the opening. Underground practical experience indicated that prior to mining, the entry was supported very well in excellent conditions. After mining, however, it deformed greatly. The current entry support technology was not effectively control the severe deformation incurred in entries driven in soft strata due to the following reasons: (1) little is known about the entry deformation behavior of the strata surrounding the opening and (2) the degree of interactions between entry deformation and roof bolting with wire mesh is not well understood. Consequently, effective supporting systems cannot be properly selected to control its deformation and maintain a stable supported surrounding structure.

Jan 1, 2012