Search Documents

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro, Diogo Neves Henriques

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850 to 1100oC. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at temperatures above 1000 ° C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antônio de Pádua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antônio de Pádua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [3,4]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2008

By Xuerong Wen

The oxidation behavior of TiAl3 intermetallics was investigated as a hnction of time at 1273K in pure dry oxygen. The oxidation experiments were carried out using TGA method. The oxidation scales were analyzed using SEM, EDS and X-ray diffraction methods. The structures of oxides formed at the different oxidation times were analyzed. The mechanism of oxidation of TiAl3 intermetallics was discussed.

Jan 1, 1998

By B. Mishra

The application of various bydrometallurgical, pyrometallurgical and electrochemical processes in the extraction, purification and production of radioactive metals as well as the use of various materials, eg. metals and alloys, ceramics, polymers, etc. in the process, construction and handling equipment in the nuclear industry has generated a large stockpile of radioactively contaminated waste material and scrap metal which can not be directly discarded, recycled or considered for long-term storage due to its volume and potential hazards, without the separation of radionuclides. This paper reviews the emerging methods that have been 'investigated and suggested for dealing with some of these wastes' and scrap material. The separation technologies studied for the recovery of radioactive components from the pyrometallurgical and electrochemical processing wastes have been discussed in details with results from some of the recent theoretical and physical modeling work as well as the data obtained? from the actual waste treatment. Specific processes shall be described in terms of its advantages and limitations. These emerging separation technologies are being considered by the US Department of Energy as alternatives for dealing with the issues of environmental management [EMI' and decontamination and decommissioning [D&D].

Jan 1, 1996

By Rubén Alvarado

The markets and environmental protection rules are more and more exacting, both of which have determined that copper smelters should look for technological development and global management to ensure their viability and competitivity in the short and long term. The main facilities of the present and future Smelting-Converting Process at Codelco's Caletones Smelter, is based on Teniente Converter reactors with a high operational availability that have reached concentrate processing capacities near 2,000 tpd. These reactors are in operation in most of the smelters in Chile as well as in Zambia, Peru, Mexico and, in ?the near future, in Thailand. Since 1993, the Smelting-Converting process of the Caletones Smelter of Codelco-Chile has been based on one Reverberatory furnace, two Teniente Converters and four Peirce-Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers, three Slag Cleaning Furnaces, and two Oxygen Plants have allowed the smelter to reach concentrate smelting capacities and copper productions of 1,215 kt/year and 360 kt/year, respectively. This transitional operating scheme, combining together traditional and advanced technological equipment, needs further modernization to successfully face the modern world challenges, especially with relation to the environmental commitment, production costs and wide satisfaction of customers. For this reason, for the period 1997-2000, a Modernization Plan has been worked out. This plan considers an increase of the present throughput, which will permit a significant increase in productivity, as well as finding a definitive solution for meeting the environmental regulations. Among these projects, we can point out the definitive shut down of the Reverberatory Furnace, which is a contaminating piece of equipment of low energetic efficiency. Additionally, it considers the installation of two new Slag Cleaning Furnaces, one additional Oxygen Plant, and the incorporation of two new Sulphuric Acid Plants with a production capacity of 4,500 T/D, that will recover over 92% of the sulphur content, of process off-gases.

Jan 1, 1998

By M. I. Kalashnikova

Results of investigations concerning precipitation of heavy non-ferrous metals from solutions using precipitators based on elemental sulphur and lime with gypsum transfer to a separate product are given.

Jan 1, 2003

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By Qiang Zhong, Bin Xu, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

The occurrence of different ringing behaviors in oxidized pellet kiln for two kinds of coal (A and B) with similar properties, is difficult to explain based on the relationship between kiln ringing and coal properties. In this paper, the interaction of coal ash with pellet scrap powder was considered by studying the cohering behavior of powders consisting of them. The results showed that the cohering briquette strength of pellet scrap powder increased considerably when mixed with a small amount of coal ash; a maximum could be reached when the mass percent ratio of coal ash was 1.5%; the strength of powder mixed with coal B ash was always higher in same firing system. This obviously illustrated that coal B caused a more serious ringing problem. The relevant mechanism was that the stronger reactivity of coal B ash made cohering briquette have a more perfect crystallization and a more compact structure.

Jan 1, 2015

By Edgar Peek

Lixiviant regeneration is by definition a precondition for any hydrometallurgical process. In chloride hydrometallurgy either HCl or Cl2 has to be regenerated in order to establish an economically viable metallurgical process. One such regeneration process is widely used with steel pickling where HC1 is regenerated through the thermal decomposition of ferrous chloride in either spray roasters or fluid bed pyrohydrolyzers. This standard HC1 regeneration process deserves to be considered as a potential separation process, since thermodynamic calculations show that a fluid bed pyrohydrolyzer can function as a ferrous-nonferrous separator. Several nonferrous,metals such as zinc, lead and cadmium can be volatilized as a chloride under ferrous chloride pyrohydrolysis conditions. If such a nonferrous metal volatilization could be achieved in the case of slurry feeding of "contaminated" iron oxides, then this would increase the Fe/H2O ratio of the (process) feed and thus save on fuel per ton of iron, while yielding a marketable iron oxide product. Previous test work on synthetic materials revealed that the near-complete separation of zinc, lead and cadmium from iron oxide was possible in a pyrohydrolytic atmosphere, even if zinc was present as zinc ferrite (more than 99.5%). This investigation, which was carried out in a tube furnace at 1100 K has now been extended to treat synthetic zinc minerals and also franklinite ore. For the latter, it was found that 85% zinc volatilization could be achieved in 4 hours at 1300 K. It is postulated that complete zinc volatilization could not be attained due to the formation and/or presence of gahnite and hardystonite, which might be stable in HCl/H2O atmospheres at 1100 K. The effect of adding small amounts of calcium chloride to react with gahnite and hardystonite to give zinc chloride and both calcium aluminates and silicates is being discussed. Test work on slurry feeding of this complex ore in a recently constructed 4-inch diameter fluid bed pilot unit has been planned for the near future.

Jan 1, 1995

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By Satu Jyrkönen

A single-particle laminar-flow technique was used to study reactions of sulfidic nickel particles. The studied materials were three natural nickel concentrates and four synthesised nickel mattes. The variables of the experiments were the gas preheating temperature (500 - 1300°C), the composition of the reaction gas (N2 + 0 - 75 vol-% 02) and the ,particle size of the feed. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect alteration in their morphology, internal composition and structure. General reactivity of the materials was monitored by the extent of sulfur removal. The reaction mechanism of the studied materials was found to depend primarily on the materials composition as well as oxygen content of the reaction gas.

Jan 1, 1998

By B. C. Blakey

Unlike most hydrometallurgical slurries, those containing significant concentrations of goethite are typically highly viscous and shear-thinning, even at solid volume fractions below 5%. The viscosity may also depend upon time. These characteristics must be taken into consideration in slurry transport and heating. The technical literature is replete with apparent contradictions regarding the viscous behavior of these slurries, which may be due, in part, to variations in viscosity-measuring techniques. We present techniques that yield consistent results suitable for use in process design. A striking degree of time-dependent behavior is demonstrated for a laterite slurry. Reliable methods to design and analyze tubular transport and heating systems for time-independent slurries are summarized. Rules of thumb are then offered to account for the effects of time-dependency.

Jan 1, 2000

By J. Priede, G. Gerbeth

"Two different instability mechanisms of electromagnetically levitated bodies are analyzed. The first is due to the virtual coupling between the electric current passing through the magnetic system and the variation of position of the body. This mechanism can result in unstable mass center oscillations of a levitated solid body. Another type of instabilities may occur because of the coupling between the motion and the electric currents induced in the body. This effect can cause a spontaneous rotation of the body setting in as the frequency of the alternating magnetic field exceeds certain critical threshold depending on the configuration of the field. This instability can be suppressed by an axial steady magnetic field of strength comparable to that of the levitating field. 1 IntroductionAn alternating magnetic field interacting with eddy currents induced in a conducting body causes repulsion between the body and the coil generating the field. Besides, the eddy currents provide a contactless heating of the body. In such a way metallic samples can be levitated and melted without a contacting crucible. This technique allows to avoid contamination of the melt with container material and so to achieve a considerable super-cooling of the melt before it solidifies. Nowadays electromagnetic levitation is widely used in material research for measuring of the thermophysical properties of molten metals (2) .It has been observed since early fifties when the first experiments on the electromagnetic levitation were done that under certain circumstances solid levitated samples start to rotate or oscillate [l]. Surface oscillations can appear in addition when the sample is melted. Such phenomena are undesirable because they often result in failure of the levitation. Recently we showed that rotational as well as oscillatory instabilities can have electrodynamic origin related to additional eddy currents induced by motion of the body in an alternating magnetic field [3] , [4].In the first part of the present paper we analyze another possible cause of oscillatory instability due to the coupling between the electric current passing trough the magnetic system with variation of the position of the levitated body. The second part of the paper deals with the origin and suppression of rotational instability in a uniform alternating magnetic field."

Jan 1, 1999

By Yapeng Zhang, Zhiwen Shi, Chaoquan Yao, Fei Wang, Xinyu Li, Jianliang Zhang

A great deal of iron ores which have special elements have been applied in the sintering process with the decreasing of high-grade quality iron ores resources. In this paper, the laterite nickel ores were added into three different kinds of iron ores respectively to make liquid phase formation research by software of Factsage and high temperature characteristic sintering experiments. The results showed that the adding proportion of laterite nickel ores should be less than 15% when the high temperature properties of the mixing ores were well. Increasing the mixing ration of laterite nickel ores in the sintering blending would play an important role in the reduction of the sintering cost.

Jan 1, 2015

By N. Menad

Thermal treatments of five different types of non-ferrous metallurgical wastes, under controlled atmosphere, were carried out at temperatures lower than 800 °C. The aim of these treatments was to reduce the toxic elements content and to increase that of valuable metals in the residue. <Best results were obtained by their treatments in air or hydrogen or successively both of them. Simple treatments using air or hydrogen of three samples allowed the elimination of more than? 95 % of their toxic elements and&apos; almost doubled their valuable metals&apos; concentration. For the rest two samples, combined treatment was necessary for their efficient decontamination and the concentration of valuable metals, in the treatments residue, to a reasonable value. Most of the solids issued from these treatments can be recycled in .the current non-ferrous metallurgical processes.

Jan 1, 1995

By C. Mattich, A. L. Beyzavi

The Waelz Plant at Taiwan Steel Union Co. Ltd. (TSU) was erected within nine months from September 1, 1998 to May 15, 1999. The nominal capacity of the plant is 50,000 tonnes per year of electric are furnace dust (EAFD). The plant, consisting of material handling, a waelz kiln, a waste gas cleaning system, waelz oxide leaching and waste water treatment, was commissioned within three months from July 1, 1999 until October 12, 1999. The specific problem of the plant is the high chlorine content in the EAFD pellets which is up to 6 %. Lurgi Metallurgie GmbH, Frankfurt, Germany was responsible for the engineering erection and commissioning of the plant.

Jan 1, 2000

By Carlos A. Nunes

V-AI alloys have been used commercially to produce pure vanadium by Electron Beam Melting (EBM), as well as to obtain Ti-based alloys (ex. Ti-6AI-4V). The aluminothermic reduction of vanadium pentoxide (V205) is the primary method to obtain these alloys. Concerning the obtention of pure vanadium, earlier studies have indicated alloys presenting Al content between 10 and 15wt% as the most suitable alloys for direct EBM. In the present work we investigated the aluminothermic reduction of V205 in order to define process parameters for the obtention of V-AI alloys with composition in the previously mentioned range. It was studied basically the effect of excess AI, CaO addition and reaction atmosphere (air, argon) on the alloy composition (AI, 0, N). In addition, microstructural analysis of selected alloys by SEM (BSE images) and EPMA (WDX) were also performed.

Jan 1, 1996

By J. Brent Hiskey

Recently basic concepts of semiconductor electrochemistry and solid-state electronic structure theory have been applied to the dissolution of mineral electrodes. In this paper, fundamental aspects of semiconductor electro- chemistry and interfacial charge-transfer processes are reviewed. Information regarding the electronic and semiconductor properties of chalcopyrite is summarized. The electrochemical response of chalcopyrite in acidic solution is analyzed in terms of initial dissolution processes. The initial charge- transfer reaction involves the consumption of holes. It has been shorn that Fermi level pinning is consistent with observed electrochemical and dissolution behavior. Semiconductor electrochemistry has proved helpful in explaining the formation of intermediate surface films produced during the initial stages of chalcopyrite dissolution

Jan 1, 1993

By Lauri Holappa

Copper converting is mostly performed in Peirce-Smith converters. The process is still very similar to the original one developed in the early 20th century. It is a batch process in a horizontal cylindrical reactor with air blowing via tuyeres along the length of the reactor side. The Peirce-Smith converter has its roots in Bessemer&apos;s inventions in the 1850&apos;s as he tested both horizontal and vertical vessels for steel converting. However, for steel making a vertical pear-shaped converter with air bottom-blowing was established. In the course of time, there was a distinct necessity for oxygen usage instead of air due to harmful effects of nitrogen to steel properties and its cooling effect. In-bath blowing of oxygen did not succeed, however, and top-blown oxygen converter with oxygen lance (LD or BOF) was first developed in he 1950&apos;s and emerged rapidly to a dominating position. Somewhat later oxygen bottom-blowing via special shrouded tuyeres was developed (OBM or Q-BOP) but has attained only fractional share. Bottom-blowing technique had, however, impact on the current combined blown converters which adopted the benefits of both top and bottom blowing. In copper converting Peirce-Smith type converters have kept their position until today although new processes have been introduced and at least few of them seem to be emerging. In one respect copper converting has a clear leading position i.e. in the progress of continuous converting processes (Mitsubishi, Ausmelt). These processes utilise top-blowing lances instead of in-bath blowing tuyeres. A different principle for continuous converting is flash converting by Kennecott Outokumpu, which makes smelting and converting independent of each others. Solid ground matte is used as a feed for flash converting in a reactor shaft similar to Outokumpu matte flash smelting. A comparable process has been presented by Inco too. The paper discusses principal physico-chemical and process technical similarities and differences in copper and steel converting. Although these processes are metallurgically quite different it seems that during the modem history of ferrous and non-ferrous metallurgy, starting from the 1850&apos;s, the exchange of knowledge between these disciplines has been quite intensive. In long-term perspective, many similarities in the development can be found but also divergences due to different ambient circumstances.

Jan 1, 2003

By James P. Bennett

The U.S. Bureau of Mines, Tuscaloosa Research Center, is conducting a review of the usage of different types of refractories, the current industrial practices to recycle/dispose of spent refractories, and the concerns associated with these practices. This information will serve as the technical basis for initiating a research program to recycle or find alternate uses for spent refractory materials. Approximately 1.6 million metric tons of clay based and 1.2 million metric tons of non-clay based refractory materials were manufactured in the United States in 1992 alone, representing a value of almost 2 billion dollars. Landfill has been and remains the disposal means of choice. Issues such as environmental regulations, concerns over landfill disposal, future liability, and product stewardship programs have brought about increased emphasis for recycling or alternate material use. Information on refractory consumption and the issues associated with recycling or disposing of used materials will be discussed, including current recycling practices.

Jan 1, 1995

By Bryce Clark

Cobalts history from the 14th Century is outlined, with a look at its various sources over that period. The present sources and quantities are given, when in 1994 it is an equal co-product of copper in Africa and nickel elsewhere (Canada, Australia, Russia). Future trends in this scene are also examined. The final section deals with cobalts uses in superalloys, magnets, colours, electronics, chemicals, and examines trends in its markets. Supply and demand in co-product cobalt are shown, based on the latest production figures.

Jan 1, 1995