Search Documents

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

By C. Cánepa

In the treatment of many problems related with the optimization of a given ore dressing process, microscopic studies can provide invaluable assistance. Such studies are generally carried out through mineralogical determinations both qualitatively and quantitatively. Frequently the solution of a specific problem requires the combination of these in adequate proportions. Often the nature? of the problem poses some conditions regarding the way the microscopic determinations are made in order to yield useful information. Most publications applied to mineral beneficiation show results of ore microscopy without mentioning the methodological details involved in the determinative work and therefore it is not possible to judge their reliability and/or their relevance. As methodology must necessarily change from case to case, it is very important for the microscopist to identify first the direct and indirect mineralogical information required to solve the problem. Without such guidelines selection of methods for the qualitative and/or quantitative determinations cannot be made.

Jan 1, 1981

Rapidly solidified TiAl-Cr-xNb-Y(x=2,4,6, at.%) alloys have been produced using a single roller melt spinning method. The microstructure of alloy ribbon was refined and component became more homogeneously by rapid solidification technology. There were two phases in alloy ribbons, including -TiAl and 2-Ti3Al phases, yet the amount of 2-Ti3Al phase in matrix obviously increased by rapid solidification than cast alloys. The micro-hardness testing also carried out. Compared to the cast alloys, the alloy ribbons have much higher hardness.

Jan 1, 2009

By R. E. Fanning

"IntroductionThe Aluminum industry is one of many materials industries which strive to make their material the preferred choice for large volume products. In some applications one material has a natural advantage over others, but more frequently several materials compete with one another, each providing one or more advantages and some trade-offs. Customers may design their product with several objectives such as minimum system cost, maximum customer appeal or maximum manufacturing flexibility, choosing materials which best combine cost and performance. In such markets it may become necessary for a material supplier to enhance the attractive features of the particular material to outweigh its disadvantages.It is difficult, if not impossible, to predict how various materials will evolve. Technological breakthrough, government regulations, material availability or sociological issues may redefine the balance between competing materials. In spite of some uncertainty regarding the competitive position of competing materials, there is little doubt that unrelenting pursuit of product quality improvement and cost reduction are essential to future viability of the aluminum industry. It is the intent of this paper to identify some areas where technological improvement would be beneficial. Thus this paper is a collection of briefly described problems that will hopefully stimulate the thoughts and research required for knowledge based solutions. Rolling ProcessA particular example is the beverage can industry where aluminum, steel, glass and plastics vie for a share of the m.arket. The high cost of aluminum relative to steel or glass requires minimizing the amount of metal per can. The high intrinsic value of aluminum has led to extensive recycling of cans although net metal cost is still higher than that of the competing materials. Intensive engineering of the beverage can led to improved design and better understanding of material requirements. These improvements permitted substantial reduction in sheet thickness over the past decade. The downward trend in metal thickness for beverage can sheet is shown in Figure 1."

Jan 1, 1988

By F. L. Marley

Small and medium-sized flotation plants with no assaying instrumentation still depend much upon the art of the operator to produce acceptable and consistent results. Improved performance can be accomplished by the use of the simple microscope set up as a control device. The visual recognition of products in the circuit does much to eliminate uncertain shift operating decisions and is an easy technique to acquire. Mineral staining methods further assist in the determination of components within the mill products. Simple mounting upon scotch tape and other adhesives is rapid and convenient. The microscope also has a practical role for the plant metallurgist or laboratory technician when evaluating middling products, and their routing within the circuit. Examples are reviewed where the microscope has been used for operational control in both sulfide and nonmetallic mineral flotation plants.

Jan 1, 1981

By James J. Komadina, Robert R. Beebe

"Heap leaching of gold ores has enjoyed wide acceptance in the arid and semi-arid regions of the western U.S., Australia and South America. There are areas, however, where cold weather or excessive precipitation can limit the usefulness of heap leaching. Even in Nevada difficulties can be encountered which call for special operating procedures.The paper discusses the general climatological limitations and some of the techniques used to extend heap leaching into colder conditions. A case history of the Cripple Creek and Victor Gold Mining Company operation in Colorado examines 'valley-fill"" technology as an ideal cold-climate solution, where topographical conditions permit.AcknowledgementsThe authors gratefully acknowledge the management of Independence Mining Company for their permission to present this paper. The contributions of Golder Associates; Pikes Peak Mining Company Environmental Affairs Department staff, and the Colorado Department of Mines and Geology were all invaluable in successfully concluding this project.BackgroundWhen heap leaching of oxidized gold ores was introduced in the rnid-1970s it was aimed at large tonnages of low-grade material which could not, in general, be developed via conventional milling. Normally, the reasons for this were economic rather than technical: capital and operating costs for milling were simply too high. At first, grade was almost the only criterion, but deposits too small to justify milling were also potential targets for heap leaching.Renewed interest in gold was centered in the western United States and Australia, where exploration for milling-grade deposits had never really died. When heap leaching came along, it was in these areas that the first developments took place. Coincidentally, these same areas were favorable for heap leaching: climates were temperate for most of the year and competing land uses were limited. Even so, in the western United States in particular, winter temperatures were low enough to complicate operations. Precipitation was less a problem, although heavy snowfalls could periodically interfere as well."

Jan 1, 1997

By I. S. Blair

The Mufulira smelter (1, 2,' 3, 4,) is one of three smelters situated on the Zambian Copperbelt to treat concentrates and other intermediate products produced in the area. Two mining companies, Roan Consolidated Mines Limited (RCM) and Nchanga Consolidated Copper Mines Limited (NCCM) each have 51% Zambia Government participation. RCM operates two smelters, one at its Mufulira Division and the other at its Luanshya Dl vision. NCCM operates one smelter at its Rokana Division (5). The Mufulira smelter was commissioned in 1937 with two reverberatory furnaces and four converters. The final product, blister copper, was cast from a holding furnace. In 1952 two anode furnaces and a common casting wheel were installed to feed a new and adjacent electrolytic refinery. In 1956 the smelter was extended to accommodate increasing production from the new Chibuluma mine and expansion at Mufulira mine. A third reverberatory furnace, a fifth converter and duplicate anode processing and casting facility were added. The Copperbelt smelters suffered a loss of production potential when higher ash content coals were used in reverberatory smelting furnaces from 1966 onwards. This, and the planned production increases from Mufulira and other RCM mines, indicated a smelting shortfall of 55,000 tonnes of copper a year in the combined capacity of the RCM smelters.

Jan 1, 1976

By Kent D. Peaslee

When supersonic oxygen jetting is used in electric furnace steelmaking, the lance jet axis is typically inclined at larger angles to the vertical than is used in basic oxygen steelmaking. The supersonic jet is important not only for refining the steel, but for sustaining the foamy slag in the electric furnace. Physical modeling was carried out using a room temperature, two-dimensional slice apparatus in which mercury represented the metal and water-glycerol the slag. High speed video photography with image analysis was used to study the effects of the angle of inclination on the slag/metal bath. Mathematical modeling using FLUENT provided a method of predicting flow patterns and the trajectories of drops injected at various points in the flowfield. A one-half scale water model of the system, in which lance heights, angles, and flowrates simulated those encountered in steelmaking operations, was used to provide a better understanding of some aspects of the oxygen blowing process in electric furnace steelmaking.

Jan 1, 1994

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By Hao Rang

The article Is specially to Introduce the recovery process of Nb, Mn, P from slags and reutilization techniques of the remaining slags. Nb-Mn-Fe alloys which contain 14-16% Nb, 40-60% Mn can be obtained after using fire refining process of " Blast Furnace-Revolving Furnace-Electric Furnace -Electric Furnace, "meanwhile, phosphorous slags which the content of phosphorus pentoxide Is 29.21%. Further going through wet metallurgical processing and electrowinning technics to recover grading 99°o metallic manganese. Finally, phosphorous slags are grinded finely to be as phosporous fertilizers to be directly used for farmlands. Small particle size (0-8mm) rich slags are mixed with slight solid additions for balling directly, and taken Into blast furnace with blocky slags all together. The remaining tall slags are fully used as constructional materials, slags cement as well as a serial of wall materials, road materials, ground ornamental materials without burning operation and steam curing. The compressive strength range of those materials is up to 15-30 MPa. There is no more solid waste slags effluent In the full technical process.

Jan 1, 1994

By Stephen M. Testa

Several methodologies are available for the remediation of contaminated soils including bioremediation, vapor extraction, chemical fixation, incineration and direct disposal. A proven innovative and cost effective alternative for the fixation of contaminated soils is via cold-mix Environmentally Processed Asphaltm (EPA"'). EPAm methodology utilizes contaminated soil as an ingredient in an industrial process to produce a commercially viable product. Petroleum hydrocarbon and metal affected soil is incorporated with a water-based asphalt emulsion and varying amounts of aggregate to produce a range of cold-mix asphaltic products that fulfills the requirements of a variety of end uses. This viable and creative use which is within the intent and spirit of current regulations in producing, in lieu of a landfill waste, an end product for use as a berm, road base, liner, or other site specific application. Consideration of certain engineering and environmental factors including durability, stability, chemical resistance and ageing, biological resistance, permeability, leachability and geochemical aspects suggests that cold-mix asphalt incorporation of affected soil will perform more than adequately under normal conditions for a long period of time.

Jan 1, 1994

By Wei-feng Liu

On the basis of the brief introduction of the gold-antimony concentrate smelting process in China, some problems in the original process were analyzed and the corresponding improvements were introduced in this paper, such as the treatment of antimony matte, the refinement of gold-silver alloy, the concentrating gold from gold-antimony alloy, the treatment of soda slag. The roasting method that was used to treat the antimony matte was transferred to the ore dressing method. The solvent extraction was used to refine the gold-silver alloy instead of the electrolytic method. The technology of selective chlorination leaching under controlling potential was applied to concentrate gold from the gold-antimony alloy and gold-lead alloy instead of the electrolysis method. Soda slag was recovered by the second reducing smelting method substituting for the mixed-salt method of sodium arsenate. After those improvements, the process has been done smoothly; the direct recovery rate of metals has been greatly increased. Meanwhile the procedure

Jan 1, 2008

By O. Ryosuke Suzuki

A new metallurgical process via sulfide is proposed: a sulfide is produced at a high temperature from its metallic oxide using gaseous CS2, and this sulfide is electrochemically reduced to its metallic state using molten salt. This combined process via sulfide is effective to obtain high purity of metallic powder, even if the metal in its oxide is strongly combined with oxygen. For example, it is not easy to reduce stable oxide TiO2, and only Ca can remove oxygen to form α-Ti. However, a fairly large amount of oxygen remains as Ti–O solid solution. Because the solubility of S in Ti is very small, this proposal was examined experimentally both on the conversion of TiO2 to TiS2 and on the successive reduction of TiS2 to Ti. TiO2 powder was exposed to CS2 gas flow at 1073 K, and the conversion to TiS2 was confirmed. TiS2 could be reduced to Ti powder either by calciothermic reduction or electrolysis in a CaCl2 melt. By Ca reduction at 1133 K in CaCl2 melt, sulfur concentration decreased to 0.03 mass%S when the amount greater than twice the stoichiometric calcium amount is added. By electrochemical reduction at 1173 K in CaCl2–CaS melt, S concentration significantly decreased to 0.01 mass% S when four times larger amount of electric charge was supplied.

By Rejane Tubino Geyer

The volume of electric arc furnace (EAF) plus oxygen (BOF) slag produced yearly in the world is about 84 million ton. Because of this, the study of recycling processes as a way to solve the storage problem of these slags rise in importance. There are, however, some inconvenients on using this byproduct: lime, which takes part of the process of steel production, remains as a non-reactive raw product in the slag. Since lime reacts in presence of humidity, forming expansive compounds, slag use is strongly limited. There are some utilizations for the electric arc furnace and oxygen slag in the Civil Construction Industry, mainly as base, subbase and asphalt covering in highways. However, independently of the type of recycling, a period of "cure" of about six months is necessary. Because of this slow cure process this byproduct may turn non-competitive in some regions if compared, for example, with the natural aggregate. The objective of this work is to present the flowsheet of the slags production as a residue both at the electric and oxygen steel plants and, through a bibliographic review, to analize the possibilities and limiting factors for the use of steelmaking slags in the Civil Construction Industry.

Jan 1, 1996

By Toshia Suzuki, Keiji Kakudate, Yoshihiro Adachi

"A macro model for the steel usage pattern in Japan is proposed. The steels are classified into four types; converter steel for machinery and for construction and electric furnace (EF) steel for machinery and for construction. The steels are assumed to be discharged from the society in accordance with lifetime distributions of each usage. The amount of EF steel and the accumulation in society are calculated using a population balance model. The comparison with the calculated results and statistics ensures the validity of the model. Since the amount of EF steel for construction will increase and be oversupplied, EF steel will have to be used for machinery. The required and available amounts to supply EF steel for machinery are considered from the point of allowable· copper concentration for machinery use. Copper contaminates steel used for machinery during recycling process and contamination ratio is evaluated with the model. Copper concentration in EF steel is predicted for various scenarios.IntroductionThe amount of CO2 emission from Japanese steel industry is 48.0 million C-ton in 1990 and it occupies 15.1% of the total amount in Japan. In order to reduce the C02 emission and to save the natural resources, it is strongly required to promote the recycling of steel. However, the impurity contaminates steel in recycling process and lowers its quality. The copper concentration in EF steel is analyzed by Toi et al. using a macro model with the assumption that steel is discharged in proportion to the accumulation amount [1]. However the discharged amount of products is dependent on their age for service and usage pattern and not on the accumulation amount. In addition, the degree of copper contamination is different depending on the usage of steel. Therefore a precise model that contains the age for service within the society as a parameter and distinguishes the usage· of steel is necessary in order to clarify the problems in the recycling of steel."

Jan 1, 2000

By Dai Yongnian

"The feasibility to vacuum distillation of a crude metal or an alloy was discussed. The equilibrium relationship between vapor phase and liquid phase in A-B system - - - - - PA/PB =BAa*/b has been derived. The separation coefficient, BA = rAPA/(rBPB) is a judgment criterion. By calculation PA/PB, the equilibrium composition diagram of vapor phase and liquid phase was drawn. By use of the equation derived by M. Olette, the relationship among the volatilization amounts of various impurities in a crude metal (yi) was further solved. 1-(X/100)= C =(1-Y1/100)1/02i . From yi value obtained in practice, 2i, Pi and then can be calcu-lated. The correct volatilization order of various impurities was obtained. These results can be applied to determine the practical conditions (temperture, vacuum degree, type of distilla¬tion furnace, times of distillation and control of product composition) in distillation of a crude metal or an alloy.INTRODUCTIONRefining and separation of various impurities from nonferrous crude metals by vacuum distillation have many the advantages of high metal recovery, impurities recovered in metallic state, flowsheet simplified, good enviromental protection, low operation costs and in complex equipment. So in recent years this method has been adopted widely.Vacuum distillation has also been studied and used in separation of various elements from non-ferrous alloys and the area of its application is being extended rapidly.At this situation, some problems have been put up: What kind of impurities can be removed from crude metals? What kind of alloys can be separated by vacuum distillation? In present paper, attemps have been made to answer these problems and combine with practical results to analyse some valuable data obtained from testwork on vacuum distillation of crude tin and Pb-Sn alloy."

Jan 1, 1988

By Xueming Lv

The rotary kiln-electric furnace (RKEF) process is the main method for producing ferronickel from nickel laterite ore. However, this process is energy intensive as it involves several high temperature steps. Therefore, a novel process is proposed to directly produce ferronickel from nickel laterite ore by semi-molten reduction, which is expected to be realized in a rotary hearth furnace (RHF). The RHF process is able to shorten the flow sheet, decrease the reaction temperature as well as reduce energy consumption. In this study, the influence of basicity on reduction of nickel laterite ore was investigated. The results showed that it is possible to produce the ferronickel nugget directly at 1400 °C when the quaternary basicity [(mCaO + mMgO)/(mSiO2 + mAl2O3)] was fixed at 0.60. Under this experimental condition, the grade and the recovery ratio of nickel reached 11.53% and 98.59%, and the grade and recovery ratio of Fe were 84.16% and 68.72%, respectively.

"In this paper, a mobile heat treatment furnace from Akkermans Gloeitechniek, a Dutch company, was simulated with Computational Fluid Dynamics (CFD). The furnace is cylindrical with four oil burners, and large metal products such as dredging pumps and impellers can be flexibly heat treated to obtain required microstructure and mechanical properties through stress relief, annealing, hardening and tempering. The furnaces are exposed to the open air, and thus the heat loss becomes significant and varies from day to day and from season to season. Since the temperature of the metal products to be heat treated can only be measured on the surface, the temperature evolution inside the metal could not be tracked in practice. CFD simulation provides a useful tool to predict the temperature evolution within the metal pieces and within the combustion space of the furnace. Energy distribution and heat loss can be subsequently estimated. An overall energy balance through temperature measurement indicted relatively low energy efficiency. Especially during the soaking period, the high energy supplied is barely used to compensate the heat loss of the furnace to maintain a constant temperature of the metal piece. The current CFD modeling aims to give advice on how to modify the design and optimize the operation to reach higher energy efficiency and low heat loss. The CFD model consists of turbulent combustion model, radiation model in participating media, and conjugate heat transfer between the combustion space and solid metal. Temperature measurement was carried out to provide thermal boundary conditions and overall energy balance of the operation. After the model validation with temperature measurement within the combustion space and metal surfaces, furnace optimization will be conducted.IntroductionHeat treatment is a common practice in metal production and manufacturing industries. Through heat treatment at certain temperatures with special patterns, unique mechanical properties of the metals and the metallic products could be obtained. ""Akkermans Gloeitechniek"" is a company situated in K.inderdijk, at location of LHC-Holland (www.ihccaland.com), the Netherlands. Heat treatment of metals is its core business. Various type of heat treatment are applied, such as stress relieving, soft annealing and hardening (quenching), tempering, transformation and precipitation. At the company 6 furnaces are in operation and the 7th is being built"

Jan 1, 2004

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013

By Sergio N. Monteiro

Polymeric matrix composites reinforced with coir fibers are being used in many industrial applications such as automobile interior panels and cushions. These composites have relatively low mechanical strength due to the weak fiber/matrix interface. The objective of the present work was to investigate the effect of a surface alkali treatment of the curaua fiber on the mechanical behavior of polyester composites with different amounts of these fibers. The treatment, also known as mercerization, was performed with distinct concentrations, 0.1 and 10% of NaOH at 1 min and 1 hour, before incorporation of the coir fibers into the polyester composite. The results showed no significant change in comparison to similar untreated coir fiber composites. A microstructure analysis revealed that, in addition to reducing the hydrophilic characteristic of the fiber,the treatment also affects the surface morphology and impairs the fiber/matrix interfacial strength.

Jan 1, 2009