Search Documents

By Wei Liu

A new process for extracting cadmium from the electric precipitated dust produced by ISP process was studied. A leaching rate of 89.1% of cadmium was attained by leaching the dust with NH3?H2O-(NH4)2SO4 system under the best leaching conditions: ratio of liquid to solid(l:s)=2.5, c(NH3):c(NH4+)=3:5, total concentration of ammonium and ammonia=8 mol?L-1, leaching time= 1.5h, temperature=35. The most troublesome impurity of lead could be deposited from the leached out solution automatically after put it static more than 15h when the total concentration of zinc and cadmium was up to 45gL-1 , and the final concentration of lead was 0.0047 gL-1, which meant 99% of it was removed. Metallic cadmium which contained cadmium more than 99% was prepared by electrowinning under the conditions: current density=750Am-2, total concentration of Cd2+ and Zn2+>25gL-1. The current efficiency was about 87% and the energy consumption for every ton of cadmium was about 548KWht-1. Main impurities of the metallic cadmium were copper and zinc and all of they could be got rid of in the following pyrometallurgical refining step.

Jan 1, 2006

By W. G. Davenport

The offgas from flash furnaces inadvertently contains dust. The dust contains 25 to 30% Cu so it must be treated for Cu recovery. This is almost always done by recycling it back through the flash furnace*. This chapter shows how dust production/recycle is included in our matrix calculations. It then discusses the effects of dust production/recycle on flash furnace industrial oxygen and oil requirements. It concludes that re-smelting of dust requires considerable industrial oxygen and fuel, so that dust production should be minimized. Recycled dust also takes the place of new concentrate in the flash furnace feed system, decreasing Smelter productivity -another reason to minimize dust production. Compositions of industrial dusts are given in Appendix VII and Table 18.3. Industrial quantities are given in Tables 2.1, 3.1, 19.1,20.1' and Appendix VI.

Jan 1, 2001

By L. J. Friedman

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric ?acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design _to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators, The current? design offers improved' impurity scrubbing along with increased reliability. in addition, a number of alternate gas cleaning systems have been offered Chemetica LAB System; Monsanto DuPont D:Jna-Wave Syatem1 Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems. _

Jan 1, 1992

By John R. Howell

"SUMMARYThe process of producing a new cast component requires significant design and development by both the design engineer and the foundry engineer. This effort strives to produce a high quality component at minimum cost. To assist in this development, an analysis system, consisting of several computer programs, has been developed to simulate the metal casting process. This system incorporates analytical geometric solid modeling, finite element analysis, results display, and an innovative technique to model the casting mold with surface boundary conditions.The simulation has produced excellent thermal results and work is in progress to develop techniques to enable use of this data in additional analyses to predict porosity and residual stress. Research is required to produce working parametric formulations of material properties. Software development is required to develop good fluid flow analyses for large. 3D models to simulate filling of and convection in molds.Integrating this system of programs is difficult due to proprietary database structures used by software developers. However, an acceptable means has been accomplished' to move data from one program to another. Further software development is required to facilitate this task. INTRODUCTIONThe process of producing a new cast component requires significant design and development by both the design and foundry engineer. This effort strives to produce a high quality, reliable component at minimum cost in a timely manner. The design engineer needs to know the physical and mechanical properites which can be expected in the actual part at critical areas. This will enable him to design a part with minimum material while fulfilling the performance required. The foundry engineer needs to produce a sound, quality casting with a minimal amount of material In risers, the feeding system and machining stock. This must be done with a minimum· investment in tooling and development time and maximum productivity of labor and capital employed. This task Is continually being made more difficult because of increased competition in the marketplace and the use of castings in more severe service. This has strongly influenced the need for high quality castings.The task of developing a new casting is difficult for both the design and foundry engineer. To assist in this development, Deere & Company has been engaged in the development of an analysis system to simulate material processes. A major portion of this program involves simulation of the metal casting process. This analysis system has evolved into a package of computer programs which simulates casting solidification and subsequent cooling through the finite element method"

Jan 1, 1986

By Toshio Kurikami, Koichi Yamazaki

"Toho Zinc Co., Ltd Chigirishima Refinery has the production capacity of electrolytic lead for 95000t/y by sintering- blast furnace electrolytic process. Lead raw materials are lead concentrates, spent batteries and dusts that contain lead from other companies, and these are handled by existing smelting process. There are many circulation materials in the process, because the system has been constructed with improving the recovery rate and protecting the environment. This report describes material balance in each process, distribution of the lead and various components, and it examines present state of the processing. In addition, we report the result that we have tried to improve the work environment.IntroductionThe Chigirishima Refinery of the Toho Zinc Co., Ltd. is located in Chigirishima, an island 4km off the coast of Takehara-city, Hiroshima, Japan. The Chigirishima Refinery began lead smelting operations in 1951.The Chigirishima Refinery adopted the sintering-blast furnace-electrolytic process and has an electrolytic lead production capacity of 95,000 tons/year. The existing smelting process handles raw materials from lead concentrates, spent batteries, and lead-bearing dust from other companies. This system was constructed with the intentions of improving material recovery ratios and protecting the environment; therefore, there are many materials recirculating throughout the smelting process. This report describes the material balance in each process and the distribution ciflead and various components, and it examines the present state of processing. In addition, we report the results of our attempts to improve the work environment."

Jan 1, 2000

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.

By Sugui Tian

By means of the T6 treatment, the measurement of creep curves and microstructure observation, the influence of T6 heat treatment on the microstructure and creep properties of Ti-6Al-4V alloy is investigated. Results show that the microstructure of the forged alloy consists of the banded-like a phase and networks b phase. After sub-temperture T6 treated, the microstructure of alloy consist of the block a phase and ?networks basket? structure. Under the conditions of the applied stress of 575 MPa at 4000C, the forged alloy displays a lower creep lifetimes, after T6 treated the creep lifetimes of the alloy is enhanced to 548 h from 66 h, which is attributed to the formation of the network basket structure in which the needle-like phase are dispersedly distributed. As creep goes on, the denser dislocations in the a phase are concentrated to occur the dynamic recrystallization for refining grain. which is a main reason of the alloy displaying a better creep lifetimes and plasticity. Thereinto, the creep mechanism of the forged alloy is thought to be the slip of the straight <a> and <a+c> dislocation are activated on the prismatic planes and pyramidal planes, while the creep mechanism of T6 treated alloy is that wave-like <a+c> dislocations are activated on the pyramidal planes.

Jan 1, 2009

By Bob Hannah, Peter C. Hayes

The changes that are happening in the world of metallurgy, and with it university education, are generational and require generational responses. Some of the key issues facing metallurgical education and ongoing professional training are explored. What will be required of metallurgical engineering professionals in the coming decades? What knowledge and skills will be needed? How to provide the educational and learning pathways, and how to attract smart young people into this profession? These are issues more readily addressed by tertiary institutions in conjunction with industry; perhaps the greater challenges lie in building and maintaining competencies post-graduation. There is a need to establish and maintain a system that supports graduates and enables them to develop further into competent expert engineers able to successfully address complex engineering challenges.

Jan 1, 2014

By Nickolas J. Themelis

Nearly thirty two million tons of municipal solid wastes (MSW) are combusted annually in over one hundred U.S. Waste-to-Energy (WTE) power plants, thus reducing the use of fuel oil by about 1.6 billion gallons of fuel oil One of the advanced WTE processes is the 0.9-million ton/y SEMASS facility at Rochester, Mass. Most of the combustion in the three giant combustion chambers occurs while the injected shredded wastes are in suspension, i.e., in flash combustion mode. The velocity, temperature, and concentration profiles in the SEMASS combustion chamber were simulated by representing the combustible fraction of MSW by the simplified formula C6HIO04 and using the CFD program Fluent to solve the turbulent energy and mass transport equations. After validation against plant data, this model will be used to examine options for increasing the productivity of WTE combustion chambers, such as optimum distribution of primary and secondary air and oxygen enrichment.

Jan 1, 2003

By Jim Sarvinis, Rory Hynes, Elizabet Cruz, Kerry McKenna, Maytinee Vatanakul

"Energy efficiency improvements achieved using heat recovery processes offer benefits to both the business case and environmental impact of metallurgical facilities. Global demand drives the development of lower and lower grade ore bodies. This trend results in higher energy intensity and consequently increased waste heat. Waste heat boilers and Organic Rankine Cycle (ORC) processes are becoming cost competitive methods of utilizing this waste heat.This study analyzes heat recovery from available sources to produce power using, • High grade: waste heat boiler and steam turbine generator. This system will produce electricity, and/or process steam.• Low grade: ORC to produce electricity. The cycle is well adapted to low- moderate temperature heat sources.Processes used in metallurgical plants, such as hot exhaust streams, cooling and condensers could benefit from application of these systems.The study demonstrates:• The energy and cost saving potential of waste heat recovery technologies,• The environmental benefit.IntroductionIn recent decades, process intensification has resulted in increased productivity from unit operations such as kilns, fluidized bed reactors and smelting furnaces and decreased unit operating costs. In the coming decades, the industry’s challenge will be to continue this trend while at the same time decreasing the consumption of fossil fuels and further reducing the environmental impact of its processes.The U.S. Department of Energy reports that available waste heat sources in industry, which is approximately seven quadrillion BTU (~7,400 PJ/y), exceeds the current production of all renewable power sources combined. In Canada there are about 2,300 PJ/y of available waste heat, with the pulp and paper, metallurgy, chemical/petrochemical and oil refining industries the main players. Natural Resources Canada (NRCan)9 has estimated that about 25% of that heat could be recoverable using existing technologies, which in turn, represents a reduction of 27 Mt/y of Green House Gas (GHG) emissions, plus considerable water savings due to lower water cooling requirements and less fossil fuel consumption."

Jan 1, 2011

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By Z. Zak Fang, P. Fan, S. Middlemas

"Titanium dioxide (T1O2) has been widely used as pigment in paints, paper and cosmetic products, as well as high-tech applications such as PV Cells, semiconductors, biomedical devices and air purification. T1O2 pigment is primarily produced by the high temperature chloride process, resulting in considerable CO2 emissions. A novel hydrometallurgical process for making T1O2 pigment without direct CO2 emission is investigated. The new method promises to eliminate direct CO2 emissions, consume significantly less energy, and produce minimal environmental waste. The novel process involves molten salt roasting of titania slag, with subsequent washing, leaching, solution purification, hydrolysis, calcination and post-treatment stages, resulting in high-purity anatase or rutile pigments while realizing significantly reduced environmental impacts. Pigment whiteness is critically sensitive to trace amounts of discoloring impurities such as iron and chromium. Several methods for reducing the levels of these impurities are investigated. Energy consumption and emission models are also developed.IntroductionTitanium dioxide (T1O2) is one of the most commonly used minerals in the chemical manufacturing industry. It has been commercially processed since the early 1900's, and has a wide variety of applications. Pigment is used in paints [1], plastics and paper [2], sunscreen [3], cosmetics and even as a food additive [4]. T1O2 has also been used in photovoltaic cells [5], biomedical devices [6], and in air purification [7]. T1O2 pigment has a refractive index of 2.7, which imparts a high level of opacity (and hence whiteness) to whatever material it is added [8]."

Jan 1, 2012

By K. A. Elbarawy

Processing of Egyptian barite ore with a composition of 85.5% BaSO4; 2.75%SiO2;1.56%Fe2O3 and 5.1% Al2O3 was performed with the aim to prepare pure barium salts. The process took place through pelletization-solid state reduction and leaching steps. Each of these steps was optimized. Pure barium sulphate (99% < 0.82µm) and carbonate (99%<0.75µm )were the final products. This article deals with the reduction process that occur whn coal was added to the ore during pelletization in the ratio of 5:1 stoichiometry. Optimum reduction of pellets of 8-12mm in diameter was achieved after 60 minutes at 1050oC and under a rate of 5 lmin-1 of nitrogen atmosphere, where 87.79% of the ore was reduced. The kinetic studies showed that the reduction process could be modeled according to the core mechanism of diffusion control in which the effective diffusivity is based on the surface area of unreacted ore. The activation energy calculated was 92.7 kJmol-1.

Jan 1, 2006

By Hadi Fanisalek

"Most industries attempted to conduct their energy consumptions in an optimized way for a few decades. This is because policymakers and top managements in industries have felt the critical situation of a possible energy shortage that could happen for them in the near future, even in countries with significant fossil fuel resources. Decisions related to energy consumption in any industry will have a long-term effect on different parts of the industry structure. In this way, energy decisions should be categorized as part of any industry's main strategic and long-term decisions, which should be made by top strategists. On the other hand, strategic management has many powerful tools to help the policymakers in industries to establish a long-term strategy for energy consumption and reducing or preferably eliminating the energy loss. This will be more important for industries in the Middle East, where they have just started to make an applicable strategy for their energy consumption and to design a long-term procedure for their energy management. Based on strategic management and by comparison we designed and offered a new model for establishing the main structure of energy management strategy in primary aluminum industry, which is a high consuming energy industry. This strategy, which we will call ESM (Energy Strategic Model) and has been applied for a typical primary aluminum industry in this paper, is similar to the practical models in the field of strategic management, which were developed for designing the overall company strategy.IntroductionThe elementary goal for introducing strategic management in any organization was to establish a successful plan helping the company to survive and to gain competitive advantage over its competitors in a rough business environment. Strategic management is an ongoing process that evaluates and controls the business and industries in which the company is involved; assesses its competitors and sets goals and strategies to meet all existing and potential competitors; and then reassesses each strategy annually to determine how it has been implemented and whether it has succeeded or needs replacement by a new strategy to meet changed circumstances, new technology, new competitors, and a new economic environment[!]."

Jan 1, 2013

By Nobuaki Sato

The electrical conductivity, k, of pure and sodium doped sulfur melts was measured with and without ultrasonic waves at temperatures ranging from 140 to 340&apos;C by the two probe method using an ultra high resistance meter. The k value of the pure sulfur melt with irradiation jumped at around 170°C by an order of 102 after which it mouutuniocally increased from 10-5 to10-4 A&apos; 1 cm-1 with an increase of the temperature. The addition of the sodium metal to the sulfur melt was found to cause a larger jumping in the K value. The k value increased with the increase of Na proportion in the melt. For a 10mol% Na doped sulfur melt it was as high as max ~30 A 1cm -1 above 180 C under the irradiation of of ultrasconics.

Jan 1, 2003

By E. A. Román

An ion exchange pilot plant, provided by Mesco Inc., was tested for antimony control in the electrolyte at three Chilean tankhouses for copper electrorefining: Chuquicamata, Potrerillos and Enami -Ventanas. The pilot plant, with a nominal extraction capacity of 1.2 kg Sb/day, worked connected to both experimental and commercial circuits, performing a total of 310 loading and elution cycles. An innovation in this process is the use of a chelating organic elution reagent, which presents some advantages over the traditional 6N HCI. This new eluent is amenable to continuous regeneration and recycling with high recovery efficiency. Antimony removal starting at initial, concentrations of 0.5 to 0.6 g/l of Sb down to steady concentrations of 0.1 to 0.0.6 g/l Sb, resulted in the production of High Grade copper cathodes with Sb contents below 0.1 ppm. Anodic slimes showed Sb contents below 1%.

Jan 1, 1999

By Daoxin Wu

In this paper, the rutile TiO2 were prepared under air, Ar and H2 calcination atmosphere by low temperature hydrolysis using Tetrabutyl titanate (C16H36O4Ti) as raw material. Powers were characterized by X-ray diffraction, UV-vis diffuse reflectance and X-ray photoelectron spectroscopy. The influence of the calcination atmosphere on the photocatalytic reactivity of rutile TiO2 for oxygen production was investigated. The photocatalytic reactivity of rutile TiO2 prepared under air, Ar and H2 atmosphere was compared under ultraviolet and visible light radiation with Fe3+ (c=8.0mmol.L-1) as electron acceptor. The results showed that rutile TiO2 prepared under Ar and H2 atmosphere had higher photocatalytic activity for oxygen production than that prepared under air atmosphere. The oxygen production rates under ultraviolet irradiation were 427.5, 378.2 and 357.0µmol.l-1h-1 respectively when rutile TiO2 was prepared under Ar, H2 and air atmosphere. The oxygen production rates under visible light irradiation were 78.2, 52.2 and 13.5µmol.l-1h-1 respectively when rutile TiO2 was prepared under Ar, H2 and air atmosphere.

Jan 1, 2008

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By Mei Song, Qingyu Deng, Xuewei Lv, Lu Liu, Chenguang Bai, Meilong Hu

"The carbochlorination of several silica materials was carried out in the temperature range from 900 °C to 1200 °C. In this study, silica oxides and gaseous chlorine with carbon as reductant were used. The optimal carbon silica mole ratio in different temperature was calculated by Factsage software and the results showed that the optimal values are 1.2, 1.4, 1.6, 1.8 at 900 °C, 1000 °C, 1100 °C, 1200 °C, respectively. According to the experiments, the chlorination ratios of several silica materials were increased with temperature increasing. In the same temperature, the chlorination ratio of diatomite is the maximum and the chlorination ratio reaches 79%% when C/SiO2 reaches 3 at 1100 °C.1, IntroductionPolycrystalline silicon is the main material to manufacture the silicon polished section, solar battery[1] and high purity silicon wafers[2], also which is the most basic function material of semi-conductor industry, electronic information industry and solar photovoltaic battery industry[3]. The conventional manufacturing process of polycrystalline silicon would be divided into three parts: the improved Siemens method, which was introduced and became the main process to produce the polysilicon products in China. Silane method and fluidized bed method. Silicon tetrachloride and chlorosilans have been employed as by-products in several fields like electronic, telecounications and metallurgy[4-6]• At present, the main applications of silicon tetrachloride include production of trichlorosilane by catalytic hydrogenation, synthesis of fumed silica and ethyl orthosilicate, production of optical fiber grade silicon tetrachloride.The conventional routes for the silicon tetrachloride production have been reported, including the direct chlorination and the chlorination process of ferrosilicon, abandon catalyst and silica[7]."

Jan 1, 2013