Search Documents

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Eliezer Martinez-Jimenez, Gretchen T. Lapidus

"Electro-assisted reduction is an effective pretreatment to render chalcopyrite less refractory towards oxidative leaching. In this process, chalcopyrite is selectively converted to chalcocite or copper metal in an electrolytic cell under ambient conditions, while ferrous ion is leached into solution. However, the reaction velocity is hampered by the formation of a ferrous sulfide passivating layer on the solid surface, especially at elevated solid to liquid ratios. In the present work, several strategies for overcoming this problem were evaluated. On one hand, specific ligands for ferrous ion were added in order to increase its solubility and, on the other, an anode material which promotes the oxidation of the sulfide ion was chosen. Leaching tests showed citric acid to be an effective ligand for both ferrous and ferric ions and, in combination with a lead-silver anode, significantly increased the kinetics of chalcopyrite reduction and subsequent copper leaching.IntroductionAttempts to oxidize chalcopyrite at a rapid rate in aqueous solutions, below their normal boiling point, have met with difficulties because of passivation by some of its own components. An alternative line of research explores reductive pretreatment, transforming the chalcopyrite into less refractory copper phases, which can later be oxidized. A recompilation of these efforts up until 2000 was published by Dreisinger and Abed [1]. However, this practice usually requires large excesses of reducing agents, such as copper, lead, aluminum or iron, and in this last case at near-boiling temperatures, in highly"

Jan 1, 2012

By Laurentiu Nastac

"Two advanced control solidification technologies were studied in this article to improve the quality of the cast ingots as well as to control the solidification structure evolution during the plasma arc melting (PAM) processing of Ti-6-4 ingots: (i) electromagnetic stirring (EMS), and (ii) ultrasonic treatment (UST). The developed EMS modeling approach is based on the numerical solution of Maxwell's equations, fluid flow, and heat transfer equations, and mesoscopic modeling of the grain structure. The UST analysis tool is capable to model acoustic streaming and cavitation. It is used in this work to study ingot solidification under the presence of ultrasound. Predictions of the macrostructure, GET formation and primary dendrite arm spacing for PAM Ti-6-4 ingots processed with and without EMS or UST were discussed.1. IntroductionTitanium (Ti) alloys are melted, refined and cast into ingots through plasma arc cold hearth melting (PAM), electron beam cold hearth melting (EBM) and vacuum arc remelting (VAR) for jet engine applications. Process modeling has become a viable tool to optimize the PAM, EBM, and VAR processes. A comprehensive modeling approach to simulate ingot solidification phenomena in primary melting and secondary remelting processes of Ti alloys would include models for macroscopic mass transfer, heat transfer, fluid flow, acoustic, electromagnetic and species transport. The approach should also include microscopic models to predict the evolution of grain structure in solidifying ingots in conjunction with electromagnetic stirring (EMS) and ultrasonic stirring (UST)."

Jan 1, 2012

By Tatsuro Ariyama, Michitaka Sato, Atsushi Sakai, Sumiyuki Kishimoto, Ryota Murai

"In order to achieve high pulverized coal injection operation in a blast furnace, optimization of the injection lance arrangement was carried out using an experimental furnace and mathematical models. To increase the injection rate of pulverized coal, it is required to raise the combustion efficiency of pulverized coal. It became clear that multi-point injection and the lance arrangement to avoid interference among the coal streams injected were so effective in increasing combustion efficiency. With these findings, the eccentric double lance arrangement has been newly developed.At NKK, Fukuyama No.4 Blast Furnace, after the improvement of the lance arrangement, the maximum injection rate reached up to 230 kg/thm and an average monthly record of 218 kg/thm was successfully achieved.IntroductionFrom the viewpoints of reducing the production cost of pig iron and prolonging coke oven life, high pulverized coal injection over 200 kglthm is actively pursued by ironmaking industries[1-2].Coal particles injected into the blast furnace are consumed by combustion in the raceway and also in-furnace reaction like solution-loss reaction (C + CO2 = 2CO). The amount of coal consumed by the latter process is determined by the carbon balance in the blast furnace and there is a limit. Therefore, to increase the injection rate, it is desirable to improve the combustion efficiency in the raceway. For these purposes, the optimization of the lance arrangement was examined by a hot model and mathematical models."

Jan 1, 1996

By Neil E. Izatt, Ronald L. Bruening, Steven R. Izatt

"IBC has developed environmentally friendly Molecular Recognition Technology (MRT) processes to selectively extract, recover, and purify a wide range of metals from a variety of process streams. The incorporation of MRT into process flow sheets can improve the economics of the processes. MRT separations are effective even at low (mg/L to \i%JV) metal levels. MRT processes are sustainable, being economically viable, energy efficient, and environmentally friendly as well as having a low carbon footprint. Examples of MRT processes will be presented and discussed involving platinum group metals, gold, rhenium, and other metals of interest to the mining community.IntroductionA significant portion of the earth's precious metal resources has been moved during the past century from underground to above ground [1]. This movement has important economic, health, environmental, ecological, and sustainability implications for the earth and its population. There is concern that recycling of certain precious and specialty metals from end-of-life (EOL) electronic wastes (e-wastes), catalyst wastes, mining waste streams, and other waste products such as rechargeable batteries is not adequate to maintain supplies of these metals sufficient for future needs [2-4]. Improved metal recycling rates and more efficient metal recovery from the enumerated wastes would significantly reduce the amount of virgin metals that must be mined to support our lifestyle [5]. More efficient separation procedures in ore processing flow sheets and more effective recovery of metals from low-grade waste streams would reduce metal loss in the mining industry."

Jan 1, 2012

Today’s world relies upon advanced green technologies that are made of critical elements with unique properties. Examples include rare earth elements (REEs) that are critical in the manufacturing of wind turbines and electric/hybrid vehicle batteries, key components of a greener future that face supply uncertainty and near zero recycling. To tackle their supply challenges, activities have begun for urban mining from waste electrical and electronic equipment (WEEE) that contain considerable amount of REEs, but their current level of recycling is less than 1%. Current recycling practices use either pyrometallurgy, which is energy intensive, or hydrometallurgy that utilizes large volumes of acids and solvents and generates large volumes of hazardous waste. In this study, we developed a novel and sustainable process to recycle REEs from WEEE, NiMH batteries in particular. The developed process relies on supercritical fluid extraction (SCFE) utilizing CO2 as the solvent, which is abundant, safe, cost effective, and inert. The effect of seven operating parameters, namely temperature, pressure, residence time, sample to chelating agent ratio, agitation rate, complex formulation, and methanol addition on REE extraction efficiency was investigated, and optimum operating conditions were determined. This work is the first to utilize a very efficient and safe process that runs at low temperature to extract metals from postconsumer products with minimum hazardous waste generation, while offering about 90% leaching efficiency for REEs. We expect our process to find widespread applicability in urban mining of REEs using green chemistry.

By Jr. Santafé, Lucas L. da Costa, Felipe P. D. Lopes, Sergio N. Monteiro

"Residual vegetable fibers as leftovers from crops, industrial activities and consumable items are realistic options to be incorporated into low cost polymeric composites with the aim of replacing other commonly used materials. The present work assesses the technical properties of epoxy composites reinforced with residual fibers from the coconut fruit, also known as coir fibers. Based on these properties, an evaluation was carried out on these coir fiber/epoxy matrix composites to be used as building panels and furniture in comparison with conventional materials.IntroductionThe utilization of waste from industrial activities is presently recognized as important way in preventing environmental pollution as well as developing new products. This utilization would also generate employment and contribute to environmental improvement in global scale. Among such wastes, those from lignocellulosic materials represent a considerable potential for practical application. In fact, about 2.5 billion tons of these materials are currently available [1], and their fiber content is an important option for composites fabrication. Actually, lignocellulosic fibers are now replacing synthetic fibers as reinforcement in resin matrix composites owing to specific advantages such as low cost, biodegradability and renewable characteristics [2,3]. Moreover, as abundant waste, some of these lingocellulosic fibers could help reducing the use of traditional materials like wood and plastics in many industrials applications. This would prevent further stress on the environment caused by depletion of dwindling resources associated with forests and petroleum."

Jan 1, 2008

By Jing Zhang, Chenguang Bai, Fusheng Pan

"The microstructure and hot deformation behaviour of an Er-modified Mg-Zn-Ai alloy were evaluated. The results showed that the addition of rare-earth Er changed the morphology of the quasi-continuous grain boundary networked eutectic compound to globular particles. Moreover, a self-strengthening effect was identified for the alloy, which determined its deformation behavior. After hot extrusion, the yield strength and elongation to failure of the Mg-Zn-AI-Re alloy at 200°C were increased by 105% and 120%, respectively, due to an emerged dynamic precipitation strengthening mechanism.IntroductionMagnesium alloys are attracting increasing attention for applications in automobile, electronic devices and hand tools for weight reduction and higher fuel efficiency, because of their lightweight and a high specific strength. However, application of Mg is still very limited. The largest applications are still those non load-bearing castings used at room temperature, such as box case, housing, and covering. One of the main reasons is the inadequate absolute strength both at room temperature and elevated temperatures (> 100°C) of the commercially used AZ, AM series alloys, due to the incoherent interface between the secondary phase y-Mg17AI12 and Mg matrix, as well as the low thermal-stability of the y phase [1]. Besides, the heat-resistant magnesium alloys which contain rare earth (Re) as the main alloying element are very expensive. The other reason is their poor deformability. The key solution is therefore to develop low-cost heat -resistant wrought alloys."

Jan 1, 2012

By S. H. Amini

The effects of CaF2 and ilmenite on dissolution rate and diffusivity of CaO in calcium alumino-silicate based slag in a temperature range of 1500 ? 1600 ºC were studied by using the rotating disk/cylinder technique. The effect of rotation speed on the rate of dissolution in the base slag indicated that mass transfer in liquid slag played a significant role in controlling the dissolution. At a constant rotation speed, the effect of 5 wt% addition of fluxes tothe slag on the dissolution rate was investigated at various temperatures. While CaF2 had the highest effect, addition of ilmenite increased the rate of dissolution significantly. The diffusivity of lime in these slags was quantified using the dimensionless mass transfer correlations for rotating disk/cylinder in the melt. The diffusivity values were deduced using the data on dissolution rate and solubility of lime in the slags. The measured diffusivity in base slag at 1500 C was found to be about 1.32 10-5 cm2/s and increased to 3.07 10-5 cm2/s at 1600 °C. Addition of 5wt% CaF2 increased the diffusivity by a factor of 3 to 5, while 5wt% ilmenite increased the diffusivity by a factor of 2 to 3 in the temperature range of 1500 to 1600 ºC. The two examined fluxes reduced the activation energy of diffusion.

Jan 1, 2006

By Jeong-Soo Sohn

Physical treatment and chemical treatment of spent lithium-ion battery were studied in our research team. Especially we developed two types of acidic leaching for crushed powders containing LiCoO2 of spent lithium ion battery. One of them is sulfuric acid leaching with H2O2 as a reducing agent. The leaching rates of cobalt, lithium and the other metals were above 99 % at the condition of 2 M H2SO4, 10 vol. % H2O2, 75 °C, 300 rpm agitation speed, 250 g/5L solid liquid ratio and 75 minutes reaction time. And the other leaching process is the oxalic acid leaching. In this process more than 99% of Li and less than 1% of Co were dissolved at the condition of 3M oxalic acid, 80°C reaction temperature, 300rpm agitation speed, 50g/L initial solid/liquid ratio and 90min extraction time. Each process has its advantage and disadvantage. In sulfuric acid leaching, leaching reagent is very cheap and cobalt could be recovered into cobalt hydroxide. On the other hand, oxalic acid is more expensive than sulfuric acid but lithium could be dissolved selectively. Also cobalt could be recovered into cobalt oxalate and it could be changed into cobalt oxide after heat treatment. In order to select the effective recycling process, recovery rate and purity of cobalt hydroxide and cobalt oxalate were compared and it was investigated which process was more environment-friendly and economical.

Jan 1, 2006

By Yuhua Pan

Generic mathematical models have been developed for simulating heat transfer in two types of slag resistance heating electric furnaces for sulphide smelting: i) six-electrode-in-line rectangular furnaces and ii) three-electrode circular furnaces. The models are based on three-dimensional steady-state heat transfer of conduction, convection and radiation. Solidification of liquid slag into solid slag by water-cooling units, for use as freeze lining of furnace walls, is also considered in the models. The developed models are capable of providing predictions with reasonable accuracy for electric furnaces on 1) temperatures in slag, matte, cooling water, freeze lining and other solid regions as well as temperatures at various fluid/solid interfaces, 2) freeze lining thickness, 3) furnace smelting rate and 4) furnace heat loss rate. These computer models are built into executable application programs that are very efficient, with execution time less than one second, and can be easily portable to most computing platforms. This paper describes, as an example, the modelling results on heat transfer in six-electrode furnaces. The major modelling results show that in six-electrode furnaces uniform electric power inputs to the electrodes likely lead to low temperature regions close to slag and matte tapping ends of the furnaces, and the power input and the formation of air gaps between freeze lining and cooling units have significant influences on the thickness of freeze lining maintained by the cooling units.

Jan 1, 2006

By Yongxiang Yang

High temperature processing of raw materials in metals production and recycling often involves complex multi-phase fluid flow and heterogeneous chemical reactions at various scales. Good understanding of the process physics and chemistry is crucial for process operation and process development. The traditional scale-up process through laboratory scale ? pilot scale ? commercial scale route has been more and more complemented and partially replaced by full-scale process simulation. Computational fluid dynamics (CFD) has become a very useful simulation tool in process research and development. At the same time industrial applications challenge the CFD development with its complex transport phenomena, often in large-scale reactors with small-scale physics and chemistry. The current paper discusses the applications of CFD to a number of high temperature metallurgical and materials processing applications. The research was carried out by using commercial CFD codes as the framework, and the emphasis was given to the special efforts for the development and implementations of sub-models with process-dependent physical and chemical characteristics. To illustrate the application of CFD simulation to high temperature metallurgical processes and coupling of sub-models to the general-purpose CFD codes, five examples are given: (1) melting of aluminium scrap in a rotary furnace for recycling, (2) molten hot metal flow in a heterogeneous coke-bed of a blast furnace hearth, (3) gas flow heat and mass transfer in a submerge electric arc furnace for phosphorus production, (4) high temperature incineration of hazardous waste in a rotary kiln, and (5) transient heating of metals in heat treatment furnaces.

Jan 1, 2006

By Gustavo Díaz, Miguel A. García, Carlos Frías

"Under the auspices of the Commission of the European Union, a consortium composed of six European organi~ations has conducted a project to scale up the PLACID electrowinning cell to industrial size within the Placid process development. This paper is concerning the results and achievement of the industrial cell prototype after more than 1,000 hours operating time and about 10,000 Kg electrolytic lead production. In general, results have been very satisfactory, demonstrating the ability ofthe PLACID electrowinning cell to produce top quality electrolytic lead (> 99.99 %) with high current efficiency and low energy consumption.IntroductionThis paper is concerning the development of an industrial size PLACID electrowinning cell within the PLACID process development. This project began on January 1993 and was finished on April 1996.Lead metal production and manufacturing industries produce large amounts of dusts and also lead bearing slags. Spent lead-acid battery recycling also produces lead oxides from the battery pastes rather similar to those mentioned above. Those lead secondary materials are hazardous and difficult to handle by usual procedures.Existing processes to treat-lead oxides may inflict considerable damage on the environment, incur high operating costs and have limitations to produce top quality lead.The main aim of this project has been to develop a novel hydrometallurgical process able to deal with different lead bearing materials, mainly lead oxide secondaries: lead-acid battery pastes, lead fumes, furnace slags, oxide residues, etc., producing ""four nines"" pure lead in an efficient manner with a benign influence on the environment; it is called the PLACID process."

Jan 1, 1997

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By D. Valic

In 1997, 9.2 million tonnes of mined, recoverable copper was produced, of which, 1.8 million tonnes or 19.4% was produced by leaching, solvent extraction and electrowinning. The amount of copper produced by this method grew faster than those attained from concentrate smelting, signifying the growing importance of this low-cost production method. Statistical experimental design, unlike traditional approaches, allows for proper distribution of experiments within the boundaries of factors being studied such that the number of experiments required to develop a sound relationship between the factors and a response is minimized. In the past, very little use has been made of statistical experimental design in copper electrowinning studies. Traditional one- variable-at-a-time approaches are widely employed for this purpose. The present study employs a factorial experimental design to relate current efficiency with current density (180 and 300 A/m2), copper concentration (25 and 65 gL), and temperature (40 and 60 °C). Pure synthetic electrolyte with a constant acid concentration of 180 g/L was used throughout the study. The designed study produced a linear relationship where the independent variables of current density, copper concentration, and temperature, and their interactions, were found statistically significant. It was shown that current efficiency could not solely be used as a predictor of copper cathode quality. The quality of the deposit is difficult to be incorporated into a model or relation. It was determined that other measures, such as cathode morphology and crystal structure should be considered. This was done through XRD and SEM analysis.

Jan 1, 1999

By Kanchan Mondal

"Methanol, lower hydrocarbons, CO, and HCOOH formation have been by the reduction of CO2 with H2. Un-catalyzed electro-reduction requires a significant overvoltage. An alternate route has been conceptualized. Production of hydrogen from water can be achieved by chemical oxidation of a metal in water followed by oxidation of the hydronium ion by the released electrons to form hydrogen radical. It is hypothesized that circumventing the problem of the formation of hydrogen molecule is essential while having the hydrogen radical to react with CO2 forming methanol, etc. This may be possible by a bimetallic catalyst acting as a galvanic couple, wherein one metal acts as the electron donor for the production of hydrogen radical while the other acts as a catalyst for the reduction of CO2. This may enhance the reaction rates. The current concept circumvents the need for an external electric field unlike the electrochemical process.IntroductionUtilization of carbon dioxide as a raw material, not only as carbon sources but also as useful chemical feedstock is a more holistic approach to reduce air pollution by flue gases (1-3). Several methods have been proposed to maintain the concentration of atmospheric CO2 or to reduce and recycle it. One of these is the chemical fixations using catalysts. The conversion of CO2 to methanol by hydrogenation over copper containing catalysts is one of the most widely studied subjects in this area. The limitation in this reaction is the low conversion of CO2."

Jan 1, 2008

By Christine Wenzl, Andreas Filzwieser, Stefan Konetschnik

"The METTOP-BRX-Technology is a novel manifold electrolyte inlet, which allows improved productivity and production in new and existing tankhouses by achieving higher current efficiency and cathode quality, as well as using current densities higher than 400 A/m2. Two installation examples are shown: Montanwerke Brixlegg AG, Brixlegg, Austria (upgrade of existing tankhouse) and Xiangguang Copper, Yanggu, China (new tank house). Montanwerke Brixlegg AG has been using the METTOP-BRX-Technology since 2005, and converted half of the whole tankhouse to METTOP-BRX in 2011 in order to use a current density of more than 400 A/m2. Xiangguang Copper started up their second tankhouse in May 2011. This tankhouse was constructed in the same way as the existing tankhouse, but was designed for 292,000 t/a cathode copper (existing tankhouse: 200,000 t/a) by using the METTOP-BRX-Technology. This production increase is a consequence of a much higher current density, namely 410 A/m2, compared to 280 A/m2 in the old tankhouse.IntroductionCopper electrorefining has been practised for more than hundred years, the last big change being the implementation of stainless steel cathodes in the 1980s [1], In 2005, the METTOP-BRXTechnology was first introduced. This technology was developed jointly by METTOP and Montanwerke Brixlegg, Austria, and allows improvements in productivity and production in new and existing tankhouses in an economic way. The METTOP-BRX-Technology is a novel manifold inlet that allows improved tankhouse productivity by increasing current density and/or current efficiency while maintaining or improving cathode quality [2]."

Jan 1, 2012

By Balasivanadha Prabhu, Prasad P. Shanmugasundaram, Narayani Narasimhan

"The grain refinement and mechanical properties of 6061 aluminium alloy produced by equal channel angular pressing (ECAP) have been analyzed in this present study. A innovative triple shear ECAP die was developed for the processing.It was observed that the grain refinement takes place for greater number of passes. It was also found that reducing the process temperature gives fine grain and high microhardness and hence improved propertiesIntroductionTechnological changes in manufacturing industries have depended heavily on development in materials processing and process technologies. Modem industries need high performance materials for severe service conditions. Hence, it is necessary to improve required material properties to achieve better performance and greater service life. As mechanical properties of the materials strong! y depend on grain size ( d) - Hall-Petch relationship [ 1-4], the ultrafine grained (UFG) materials offer superior mechanical properties based on the above relation.Synthesising massive nanocrystalline materials presents a challenge to basic research as well as to application-related processing efforts. Production of ultrafine gram microstructures in metals and alloys having different crystal structures but always an initially coarse microstructure using severe plastic deformation can significantly enhance the physical and mechanical properties of materials. Severe Plastic Deformation (SPD) is an efficient method to induce ultra fine grained structure in materials by deforming it to large strains. Traditional techniques for introducing deformation of higher strains, such as forging, extrusion, drawing or rolling do have the inevitable limitation on required equipments of exerting enough load or pressure to cause uniform nanometer level grain refinement."

Jan 1, 2011

By Michael Sheedy

Sulfuric acid is widely used as an electrolyte for the electrorefming and electrowinning or metals. Impurities in this electrolyte are controlled by continuously bleeding solution from the tank house. In addition to the contaminant these bleed streams contain high levels of sulfuric acid and the metal being recovered. Subsequent treatment of these bleed streams often requires neutralization which generates large volumes of solid waste. Absorption resin technology employing a novel ion exchange technique known as Recoflo® allows the separation of the mineral acid from dissolved metal salts. The recovered acid is suitable for recycle back to the electrolyte circuit. The metal salt and other contaminants leave the process free .of the sulfuric acid. In this process, known commercially as the APU®, ion exchange resin is used to sorb sulfuric acid while excluding the metal salts. The purified acid is then removed by washing the resin with water. The process has been extensively used for the recovery of waste pickling acids in the steel industry and anodizing solutions in the aluminum industry. In the mining and metallurgical industries the process has been successfully evaluated for the separation of excess sulfuric acid from copper electrolytes, the removal of magnesium and manganese contaminants from zinc electrolytes, and nickel and copper from copper electrolytes. A full scale installation on a copper refinery bleed stream at Palconbridge's Kidd Creek plant in Timmins, Ontario has now been operating successfully for more than 1 year while pilot field trials have been successfully completed on other applications.

Jan 1, 1997

By J. N. Hryn

This paper describes some of the work done in Phase 1 of a multi-year, five-phase program aimed at demonstrating the economic feasibility of producing commercial-scale quantities of commodity materials derived from salt cake residue-oxide. The amount of salt cake generated annually in the U. S. is estimated to be 510,000 tons, including 340,000 tons of residue-oxide. Used beverage can (UBC) processing accounts for the majority of residue-oxiae that could be made available for further processing into commercial products. To characterize the composition of residue-oxide. eight residue-oxide samples from various secondary processors were obtained and analyzed. Surprisingly, the composition of residue-oxide was found to be independent of source or alloy family being processed, with? the exception of slightly elevated silicon levels in 3XXand UBC residue-oxide samples. Major phases detected in the residue- oxide were? alumina, spinel, and aluminum hydroxides. Preliminary economic analyses indicated that the refractory market appears to be the best choice for high value-added products produced from residue-oxide with minimum processing. Bench-scale tests indicated that low silicon containing residue-oxide is ready to enter this market, but the elevated silicon content of UBC and 3XX residue-oxide preclude this possibility. A separation technology should 'be developed to remove silicon-containing . species from the alumina and spinel values Present in residue-oxide. This technology would then allow UBC and 3XX residue-oxides to be converted to significantly higher value-added products.

Jan 1, 1995