Search Documents

By Yong Hack Lee

Electric Arc Furnace (EAF) dust is generated when scraps are treated in the electric arc furnace and usually classified as hazardous industrial waste in most countries. EAF dust usually contains 15 to 25% of zinc and 3% of lead. It is usually treated in rotary kiln (Waelz process) or landfilled after a solidification and stabilization treatment. Numerous methods have been proposed as the EAF dust treatment technology, but few of them are in operation as a commercial scale except the Waelz process. Korea Zinc performed a plant test in which 600 tons of EAF dust was treated using TSL (Top Submerged Lance) technology. The TSL technology is a low cost, proven technology for processing zinc-bearing residues. The EAF dust was first de-chlorinated and fed to the TSL furnace. Finally, clean slag satisfying toxicity criteria was generated and valuable metals such as zinc and lead were recovered as fume oxide. The fume oxide was de-halogenated by sodium carbonate and sent to zinc refinery to recover zinc and lead. The recovery of zinc and lead was 90% and 93%, respectively. Most of the dioxin in the EAF dust was discomposed so dioxin less than the Korean regulation limit was detected in the offgas, which proves that the TSL technology is the best solution to treat EAF dust.

Jan 1, 2006

By David Ellis

The next generation of Reusable Launch Vehicle (RLV) will utilize regeneratively cooled combustion chamber liners in the engines. The current design calls for using a new Cu-8 at. % Cr-4 at. % Nb (Cu-8 Cr-4 Nb) alloy for the liners. Work is ongoing to characterize the thermophysical and mechanical properties of the alloy from - 253 to 800°C, the temperature range to which the alloy will be subjected during service. The alloy has been commercially produced in quantity for NASA. The powder size has been characterized and the microstructure examined. The powder was extruded into bar using a commercial extrusion press. In addition, samples have been hot isostatically pressed (HIPed) at NASA Glenn Research Center. Both processing methods produced fully consolidated material. Transmission electron microscopy (TEM) revealed highly faulted Cr2Nb and some elemental precipitates. Cryogenic tensile testing showed the extruded specimens had significantly higher strengths than NARloy-Z (Cu-3 wt % Ag-0.5 wt % Zr) even after being subjected to a simulated braze cycle. The Young's moduli (Cu-8 Cr-4 Nb) were lower than NARloy-Z. The lower moduli is highly beneficial for reducing thermally induced stresses in rocket engine combustion chamber liners and similar applications.

Jan 1, 1999

By H. Kurokawa

Sumitomo Metal Mining decided to expand copper production capacity of Toyo Smelter and Refinery to cope with the recent copper demand growth in Asia, and to survive by reducing cost. The expansion plan is promoted to increase electrorefined copper production capacity from 270,000 metric tons in 2001 to 450,000 metric tons in 2007. The major changes in smelting section are introduction of the rotary steam dryer, renewal of the feeding system for flash furnace, improvement of the concentrate burner, modification of the flash furnace cooling materials, renewal of the slag cleaning furnace, modification of the flash furnace waste heat boiler, installment of a new converter furnace, enlargement of two anode furnaces. In addition, the gas cleaning system was upgraded and the second acid plant was installed. In the refinery section, the existing tank houses have been operated at high current density of 300A/m2 using the conventional starting sheet cathode technology and moreover a new tank house utilizing the permanent cathode technology was constructed. Although the copper production capacity has been increased, SO2 emission has been kept the lowest in the world through consideration of influence on the environment by expansion project.

Jan 1, 2006

By Ilkka V. Kojo

This paper gives an overview of the primary copper smelting business during the years of flash Smelting in the light of various projects taking into account the sustainability of copper production. Also the future challenges of copper smelting are addressed with special emphasis on the environment. Flash Smelting connected with either Peirce-Smith converting or Flash Converting offers the most economical and environmentally friendly alternatives for the smelting of normal and lean copper concentrates. For rich copper concentrates the feasibility of Outokumpu Direct Blister Flash smelting is, understandably, beyond compare. When the total investment costs for building a smelter and acid plant are considered, it is clear that Flash Smelting is the more feasible option compared to bath smelting. Reduction of equipment and operating cost is further achieved by the LUREC-process developed by Outokumpu Technology for operating plants with SO2-contents up to 25 % by volume. As an example the Kennecott-Outokumpu Flash Converting Furnace (FCF) has been in operation at Kennecott Utah Copper for 10 years and has achieved excellent results both environmentally and production vice. The FCF treats the entire output of the Kennecott Flash Smelting Furnace and has excess converting capacity. Furnace life, initially projected at two to three years, is now projected to be more than 5 years. It is likely the life will be essentially the same as a well-operated Flash Smelting furnace.

Jan 1, 2006

By Takashi Yoshida

"This paper will discuss the recent situation and future of the zinc industry from the technical point of view. It includes recent problems faced by the zinc industry and technological developments. One of the biggest problems of the zinc industry is raw materials. Traditional zinc concentrate becomes much complicated with respect to its chemical and physical properties. Thus, each process faced various problems. Also, secondary resources, generating so called recycling processes, become much more important. Recycling is, of course, a very important aspect for sustainable development of society. Secondary raw material also includes a great variety of impurities not included or very low levels in traditional zinc concentrate. Some problems are caused by these impurities. To overcome these problems some technological challenges have been taking place. Details will be discussed in the symposium.IntroductionZinc is a very useful metal based on its elechtro-chemical, chemical and physical properties. The most important usage is galvernizing of steel which is used for automobile, construction and a very wide range of other indutries. Also, zinc is used for dicasting and other alloys such as brass. Smelting of zinc is different from other metal because of its electro-chemical properties. Many parameters should be controled compared with other metals such as iron and copper. Typical zinc smelting processes are the Imperial Smelting Process (ISP) and the electlolytic process. The ISP process is a pyro-metallurgical process using a blast furnace. The electrolytic process is a hydrometallurgical process. Both processes are energy intensive, and the smelting process cost is increasing because of higher energy costs. The situation of the ISP is very severe because of higher coke prices. Recently, many ISP plants have been shut down because of economic reasons"

Jan 1, 2012

By C. P. Broadbent

Due to growing .public awareness of environmental issues and greater sensitivity towards waste management, many countries around the world are implementing more stringent legislation governing the storage and disposal of hazardous wastes containing heavy metals such as As, Sb, Pb, Cd or Hg. These wastes can no longer be dumped without providing clear guarantees that the material concerned is environmentally safe and will not leach toxic elements to the surroundings. In the Netherlands the current dumping charge for chemical waste (i.e. worst category) is $280/t, and for industrial waste this cost reduces to $75/t. If the material can be reused there may be a small positive credit for selling it, for example discard slag as an aggregate to the construction industry. A number of (pyre)-metallurgical operations, mostly associated with the extraction of metals from sulphidic ores, produce arsenic residues in the form of As2O3 containing flue dusts and speises. If the flue dust is of high purity it can be sold, though many traditional uses are being substituted by other materials. In many cases upgrading the quality of the arsenical dusts is not possible for either technical or economic reasons. Traditional practice is to dissolve these dusts in acid prior to precipitation as ferric arsenate, which is at present classified by many countries as industrial waste and can be dumped. Recent work, however, has cast doubt on the stability of arsenates for disposal and alternative disposal routes have been investigated. Tests have shown that up to 10% (dm) As can be incorporated into "glassy" silicate slags with very low levels of arsenic leaching in the cooled product. Calcium arsenate was added to a range of synthetic and industrial slags from the system SiO2-FexOy-CaO-A12O3-AsmOn, under mildly oxidising conditions and quenched subsequently in water. It would appear that this represents an environmentally acceptable method for the disposal of many arsenical residues and there is some optimism that this method will be equally applicable to the disposal of other toxic metal residues.

Jan 1, 1994

By Luis W. Pommier

The wastes of the plating industry are generated in the process of rinsing the plated objects and during the cleaning of the plating shops. High volumes of hazardous waters are neutralized on site producing recyclable water, generating a metal rich, hazardous, filter cake. Occasionally, a complete plating bath has to be discarded which increases the metal content of the filter cakes. These filter cakes are discarded as hazardous at a cost of over $ 250 per ton. The metals found in the cakes are generally copper, nickel and chromium or zinc, lead and cadmium, assaying from 2% to 15% or even higher content of each metal The metals and their contents are highly variable. Some plating shops discard their products directly to hazardous waste sites, others, have them collected by companies which consolidate wastes from several producers prior to discarding. These wastes, richer in metal content than mine ores, need neither mining nor crushing and grinding for concentration. The commonly found impurities in the mine ores, i.e.: pyrites, arsenic, and valuable metals which are present in minute quantities, are absent in the filter cakes. The processes available to selectively recover the metals from the filter cakes, are discussed based on their technical and economic merits. The flow-sheets include leaching, solvent extraction when required, and electrolytic refining. Examples, showing the separation of copper, nickel and chromium and also of zinc and lead in pilot plants, show the technical and economic viability of the processes.

Jan 1, 1996

By Jean Goldschmidt

Recycling of fine oxidized particles of non-ferrous metals usually cannot be carried out by pyrometallurgical methods. 'Hydrometallurgy provides an alternative technology to reintroduce? the resulting products as secondary raw materials into the industrial cycle, thereby saving resources and energy while keeping the environment a little cleaner. The paper summarizes the methods employed by Hydrometal to achieve these objectives and? stigmatizes the latest counterproductive international regulations which create ever more obstacles to environmentally sound recycling.

Jan 1, 1995

By M. Jortikka

The smelting process of the old reverberatory furnace including its capacity has been improved over the years in different ways eg. with oxy-fuel burners, parallel reactors with the reverb or with various modifications of the reverb furnace itself. The future reverb modifications with old concepts are difficult or impossible as the increased copper losses in slag call for separate slag treatment and particularly the process modifications do not solve the environmental issues but instead mean unavoidable high capital and operating costs in gas cleaning and sulphur recovery. During the last decades improvement in process performance and increase in capacity of copper flash smelters has been achieved easily by substituting the pre-heated process air by highly oxygen enriched air. The flash furnaces of today, however, are inherently designed to operate with high oxygen enrichment. Further process improvement with a view to production costs and capacity increase as well as to the more stringent environmental requirements is possible with even higher oxygen enrichment. This, apart from the advantages it generates, requires improvements in and careful design of the feed system, concentrate burner, furnace cooling and the off-gas line as well as adaption of the flash converting instead of the conventional Peirce-Smith converters. A logical answer even for the revamping of the reverb smelters in the future is the total replacement of the reverb furnaces with flash smelting together with flash converting. This paper discusses the possibilities for future process improvements of the existing flash smelters taking into account the process concepts, equipment modifications and capital aspects not forgetting the environmental issues. The revamping of the PASAR smelter in Philippines is introduced as an example of a recent success story.

Jan 1, 1994

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By J. C. Agarwal

Rare earth metal alloys are becoming increasingly important, particularly those of neodymium, because of their magnetic properties. This paper will present a generalized approach to the production economics of the metallic rare earth alloys. With appropriate regard for the chemistry of different rare earths and the large impact of economies of scale, it is possible to make fairly accurate estimates of the production costs of other rare earth alloys as well.

Jan 1, 1989

By M. Dattilo

Research has been conducted over the past three years using the composite anodes versus the lead alloy anodes. The Merrlin composite anodes have shown the improved performance in copper electrowinning versus the lead-calcium-tin anodes. Using the composite anodes a 100-150 mV reduction in anode overpotential has been observed versus the lead alloy anodes in sulfuric acid electrolyte. The composite coating has excellent corrosion inhibiting properties, and reduces or eliminates the formation of manganese oxide scale. Laboratory evidences indicate that, the use of these composite anodes enhances the process of electrowinning by improving the lead alloy corrosion resistance, lowers the electrode potential, reduces the need for cobalt addition, eliminates the anode cleaning, and reduces the generation of acid mist. Field tests are underway.

Jan 1, 1999

By Yoshiaki Suzuki

In 1996, Saganoseki smelter & refinery successfully shifted to a single flash smelting furnace operation and increased the copper production capacity to 450,000mtpy in 1998. As the next step, Saganoseki planned to further increase the productivity in the smelting process. Applying the latest technology and carrying out technological innovations the throughput of the flash smelting furnace has been increased to 195 tons per hour and the matte grade has been raised to 68%. In 2005, six PS converters have been successfully consolidated into four by maintaining the production capacity. This paper introduces recent operation conditions and results of implementation of technological improvements.

Jan 1, 2006

By Frédéric Pineau, Guillaume D'Amours

Semisolid metal processing of metallic alloys takes advantage of the thixotropic behavior of material with non-dendritic microstructure to produce near-net-shape components with improved mechanical properties. The much higher apparent viscosity of the semisolid billet limits the risk of oxide formed on the free surfaces to become incorporated into the easting during the process. But, the external-skin on the periphery of the billet, which is often partially solidified and contaminated with lubricants, should not be included into the casting as this can be a cause of reject for most structural parts. In this paper, a preliminary model is set-up using the LS-DYNA SPH formulation to follow the paths of the skin. Calculations carried out show that this approach appears to be very promising to predict the paths of contaminated skins into semisolid castings. It can then be utilized to design suitable molds and gating systems.

Jan 1, 2012

By John O. Marsden

In early 1998, Phelps Dodge embarked upon a program to investigate alternative technology for the extraction and recovery of copper, and other metal values, from copper concentrates. A review of all of the available process alternatives indicated that many were unsuitable for large-scale commercial application and others were clearly targeted at niche applications where contaminants (and consequently smelter penalties) were driving the decision-making. The result of this development program is the world?s first commercial application of high temperature pressure leaching of chalcopyrite concentrate at Bagdad, Arizona, which was commissioned in the second quarter of 2003. Other related processes are in various stages of development. In addition to the obvious considerations, the economic aspects of this technology have been considered in detail at each step in the development of the program. The technology developments in this area are reviewed with emphasis on the economic viability and commercial application.

Jan 1, 2003

By L. A. Barta

A new process for the leaching of chalcopyrite concentrates has been developed and tested in miniplant campaigns and locked cycle testwork carried out between 1996 and 1999. The process involves pressure leaching in a sulphuric acid solution, e.g. raffinate from copper solvent extraction. Iron in the feeds is precipitated predominantly as hematite in the autoclave, simultaneously with copper extraction. Gold and silver in the pressure leach residue are recoverable by conventional cyanidation, following flotation to remove elemental sulphur by-product. The results of recent miniplant tests and batch locked cycle tests are provided.

Jan 1, 1999

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but industrially proven methodology utilizing nitrogen species catalyzation in the oxidizing pressure leach system may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a methodology for effective treatment of precious metals bearing chalcopyrite concentrates via partial oxidation at low temperatures and pressures will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 1999

By Henry Freiser

For the last several years, a systematic investigation of the equilibrium extraction behavior of selective tervalent lanthanides with representative chelating extractions of a variety of chelating agent families has been undertaken for the purpose of learning how to obtain chelating extractants of improved selectivity for separating individual lanthanide ions. The equilibrium extraction data (expressed as log Kex) for each reagent system are linearly related to the reciprocal ionic radius of the tervalent lanthanide ions. The role of adduct formation, steric hindrance, as well as the nature of the bonding atom in the chelate ring, represent some of the factors affecting selectivity arising out of our database of over 200 individual extraction systems, which will be discussed.

Jan 1, 1989

By V. M. Paretsky

Recent developments made in the Gintsvetmet Institute in the field of autogenous smelting processes have confirmed that autogenous smelting continues to be the main prospective technology for pyrometallurgical processing of sulfide raw materials. This technology ensures energy conservation and environmental safety conforming to the current world standards for production of heavy non-ferrous metals. Two alternative processes of single-stage autogenous smelting producing white metal as well as high-basic ferrite-calcium slags have been developed and can be recommended for technical modernization of Russian copper smelters.

Jan 1, 2002

By F. E. Katrak

Rare earths markets by definition usually include not only the rare earth elements, but also yttrium. They can be subdivided into a very large light rare earth fraction (about 95 percent by weight of all rare earths consumed) consisting mainly of cerium and lanthanum and a smaller fraction (with much higher unit value) consisting of selected high-purity oxides or elements such as yttrium, europium, samarium, or neodymium. CRA estimates that the noncomnunist world market for all rare earths and yttrim was on the order of US$750 million in 1986. The main focus of this paper is on the principal uses for rare earths, some CRA-developed proprietary data on their consumption by region, and the selective nature of business opportunities in the rare earth markets. We also provide forecasts on the future trends in these markets.

Jan 1, 1989