Search Documents

By Anatoly Sudnev, Vladimir Skorohodov, Igor Kudryavtsev, Boris Radionov, Dmitriy Panov

"In cobalt production technology at a stage of solutions purification manganous cake (slime) basically containing hydroxides of the specified metals is formed. The possibility of full cobalt recycling in the basic technology of metal production at slime processing with generation of pure manganous compounds is shown. After slime dissolution in sulfuric acid in the presence of reducers the solutions containing cobalt, manganese, nickel and other nonferrous metals are formed. Optimum conditions of selective precipitation major part of cobalt by sodium hydroxide from the obtained solution are defined, thus more than 95% of manganese are remained in the solution. The cobalt precipitate is directed to the basic technology and the solution is purified by sorption. The most effective sorbents are chosen, optimum modes of its use are found. Examples of manganese recovery from the purified solutions as MnO2, MnCO3, Mn(OH)2 with a ratio manganese : impurities more than 3000 are presented.In the processes of hard alloys manufacture and processing of cobalt-bearing primary raw materials various cobalt-manganous slimes are formed. After leaching by solutions of mineral acids the problem of cobalt and manganese separation becomes an actual. The common way of metals separation in a solution is the Shreyber’ alkaline method allowing rather selectively to precipitate of cobalt hydroxide by sodium hydroxide. However this way does not allow separating completely target metals because of transfer of some manganese in the hydrated precipitate, even at its rather low content.In the given work the results of researches to improvement of a traditional way by inclusion to hydrometallurgical technology of operation of sorption separation of the specified metals are presented. The main goal is definition of conditions to achievement of the complete removing cobalt at hydrolysis with the minimum sedimentation of manganese and the subsequent additional recovery of cobalt by ionites from the obtained solutions."

Jan 1, 2008

By Cam T. Nhan

The potential use of coal fly ash as a construction material has been recognized for many years,. In this work, an admixture of the ash residue is investigated for use as a landfill liner. In particular, its performance as a chemical barrier to the leachate from the municipal solid waste (MSW,) is determined. The test specimens are a water compacted admixture of class F fly ash, low in calcium content, which is blended with lime dust and calcium bentonite. MSW is passed through the compacted fly ash specimens under a gravitational head. The. diffusion of elements in the leachate through this material is monitored as a function of time. The distribution profiles of the retained elements in the compacted admixture provide prediction of the long term performance of the compacted admixture directly affect the leachate diffusion rate, hence, the mobilities of the retained elements.

Jan 1, 1992

By C. I. A. John

The slag dump at ZCCM's Nkana Division contains some 16 million tomes of slag, deposited since the mid-1930's. The average cobalt grade of the slag is 0.65% with some areas as high as 3%. Current arisings of slag from Nkana Smelter also contain significant tonnages of cobalt. Intensive investigations were conducted in the past into methods of recovering cobalt from these slags, although none of the processes was developed to a commercial scale. The company is now working to develop a long-term strategy for ensuring the continuing production of cobalt at optimum levels, and the resource represented by the Nkana slags will be a major component in such a strategy. The present paper reviews the various processes which have been considered for recovering cobalt, both from the dump slag and from the current slags.

Jan 1, 1993

By M. E. Reed

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed) which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons Feed System could deliver the following benefits to Flash Furnace operation: ? Accurate pulse-less delivery of feed material to the head of the burner leading to improved combustion performance and process stability; ? Highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; ? Decreased pressure pulsation in the furnace due to improved combustion control and performance; ? Decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear; Plant measurements have indicated a correlation between the discharge of concentrate from the drag chain conveyor and high speed pressure fluctuations in the flash furnace settler. Pilot scale test have been conducted to illustrate that the system delivers pulse-less feed to the burner with even feed distribution axially.

Jan 1, 2006

By N. V. Sujathkumar, I. Vasudhevan, R. Santhakumar

"Freshwater ornamental fish culture is gaining importance in India and cheaper and nutrient rich live foods such as infusorians, daphnids, copepods and tubifecids are needed urgently. In this regard, adequate research has been conducted to produce such live feeds through recycling of agriculture and animal wastes. By this venture, besides generation of additional income, environment is also kept clean. In order to popularise the technologies relating to production of live foods from wastes and generate employment opportunities, training programmes were conducted for 100 Self Help Group women belonging to Thoothukudi district. The topics of the training included, breeding of ornamental fishes by utilizing the building material wastes, production of live foods through recycling of agricultural and animal wastes. A study on feed back was conducted with 100 respondents represented from different villages. The variables such as socio economic status, economic motivation, usefulness of training and constraints were included in this study. The impact assessment of this training of rural women indicated that 79 percent respondents were in favour of using the training for self employment by utilizing different kinds of wastes. Similar training programmes have also been planned in other parts of Tamilnadu. Introduction Ornamental fish culture is one of the most appropriate sectors to provide opportunities of employment to uplift the status of rural women. To ensure women utilize their full potential in useful and profital activities like freshwater ornamental fish culture, it is necessary to provide training and support for rural women which will ultimately lead to empowerment. Self Help Group Women are being trained routinely in India on the production of live foods for ornamental fish culture through recycling of agricultural and animal wastes. In this regard, training programmes were organized for the Self Help Group Women on freshwater ornamental fish culture. Which is gaining much importance in India. Cheaper and nutrient rich live foods such as infusorians, daphnids, copepods and tubifecids are needed urgently. The techniques of live feed production through recycling of agricultural and animal wastes would not only generate additional income by would also keep the environment clean."

Jan 1, 2008

By Petr Sulovsky, Pavel Leber, Jaroslava Ledererova, Miroslav Svoboda

"The properties of raw materials used for the production of building materials play an essential role in their choice. Industrial waste materials can in some cases improve the performance of new building materials, when compared with classical raw materials. The addition of waste can however negatively impact some of the building material´s characteristics, influencing its stability, service time, durability, and can introduce undesirable variation of certain characteristics over time. It is necessary that each secondary raw material intended for such use be thoroughly investigated in terms of its chemical, physical, and mechanical properties, with special attention paid to the risk components and risk parameters. It is necessary to make many- sided technological tests in relation to the required characteristics of the resulting materials for each chosen application. Moreover, the limit values for the critical (risk) parameters, which the given secondary raw material must satisfy to be used in a specific technology, need to be defined. Introduction The risk components in the industrial waste materials to be used in the production of building materials fall into two groups: - components that pose a risk of development (instant or delayed) of a process deleterious to the utility properties and durability of the resulting materials. Such processes include volume change (expansion as well as shrinkage), alkali-silica reaction, delayed ettringite formation, thaumassite attack, aggressive carbonation, etc. - elements or components that can, if released from the waste-containing building material, pollute the environment. They involve the so called potentially hazardous elements as well as compounds like fenols, PCB, PAHs etc. From the viewpoint of the presence of both groups of risk components, the wastes can be classified as: • environmentally inert waste materials. They are produced in the largest volumes and do not pose a threat to human health. Their physical and/or chemical characteristics fail to satisfy all requirements for utilization in ordinary production. The aim of technology design is to work them into the building products with suitable utility properties. • easier workable waste materials containing toxic components are produced in large volumes. In spite of the content of toxic components, their physical and chemical properties make them suitable for ordinary production, provided that the harmful substances are immobilized by the chosen technology."

Jan 1, 2008

By Richard L. Kerr

The U.S. aluminum recycling industry has experienced rapid growth in both its size and importance over the past two decades. Secondary recovery now makes up about one-third of total U.S .. aluminum supply compared with ]9 percent, of a much smaller total in the early 1970's. This growth has occurred in part because recycled metal performs as well as new aluminum in most applications, and because it provides major savings in production costs and natural resource utilization. In addition, the recycling industry has played a critical role in greatly expanded -production and reclamation of aluminum beverage cans. Recycled metal makes up over half of the content of aluminum sheet used: to manufacture beverage cans. In future years, both the-production and reclamation of aluminum cans are likely to rise in foreign markets, thus providing the industry with opportunities for further growth. Recyclers may also play a larger role in supplying auto producers who are using increasing amounts of aluminum in passenger cars and trucks. However, in order to take advantage of this growing market, an efficient infrastructure for collection of scrap and production of metal must be developed.

Jan 1, 1995

By Georgina De Micco

The National Commission of Atomic Energy is investigating a suitable physicochemical process for the conditioning of spent nuclear fuel and treatment of the scrap of research reactors of the Al-UxSiy type. A possible way of processing is through dry chlorination of the cladding with the purpose of selective separation of the aluminium from the remaining elements such as Fe, Ni, Zn, Cu, etc. transforming them into volatile chlorides. Some important advantages of this method are the thermal stability of the chlorides that allow the easy separation of the halides by physical methods and the low volume of radioactive waste generated. The interactions in the following systems were studied in the range of temperature between 150º-500°C: Al-Fe, Al-Ni, Al-Cu, Al-Zn, Cu-Zn and the pure metals. We found that the reactivity was different depending on if the elements were alloyed or separated. The separation factors of the systems under study were determined. Nickel is perfectly separated from aluminium for all temperatures, whereas good conditions for copper separation were achieved below 400ºC. In the case of iron, complete isolation was never attained. However, by decreasing temperature to 150ºC it is possible to obtain aluminium chloride with less iron content. The separation of zinc from the product was also difficult. It was detected that zinc chloride volatilization decreases when other chlorides were present, for example cooper chlorides. In the Cu-Zn alloy, zinc chlorides remained in the condensed product due to interactions with copper. The samples were characterized by scanning- electron microscopy (SEM), X ray diffraction (XRD) and atomic absorption.

Jan 1, 2006

By Yang Tian-zu

Sodium pyroantimonate which is widely used as the clarifier in the glass industry and as the synergist in anti-flaming industry respectively has a production history of about 30 years in China. At present there is the production capacity of about 20,000 tons per year in China and China is chief producer of sodium pyroantimonate. In this work the production processes adopted by the producers of China, the operation conditions and the product qualities of sodium pyroantimonate prepared by different preparation methods have been summarized, and on the basis of comparing the advantages and disadvantages for each process the most advanced method - the air-oxidation method was introduced in detail. The production processes of sodium pyroantimonate mainly include the method of oxidation by sodium nitrate, the oxidation method of hydrogen peroxide, the potash salt method, the chlorination method and the air-oxidation method etc. The method of oxidation by sodium nitrate in which the crude antimony oxide, sodium carbonate and sodium nitrate are separately used as the raw material, the flux agent and the oxidant, has the advantage of short and simple technological process, but low grade quality of sodium pyroantimonate and bringing about serious environmental pollution are the disadvantages and this method has been substituted by other methods. Sodium pyroantimonate can be directly prepared by the hydrogen peroxide oxidation method with the advantages of simple technological process, high grade quality of the product and little environmental pollution. High grade quality of sodium pyroantimonate can be also synthesized by the potash salt method, in which industrial antimony white, the hydrogen peroxide, potassium hydroxide and sodium hydroxide are applied as the starting material. The disadvantages of these two preparation methods are high production cost and high requirements on the raw materials. The chlorination method with the crude antimony oxide, hydrochloric acid and chlorine as the raw material has the advantages of low production cost and high grade quality of the product. However complex process, high requirement of anti-corrosion for the equipments and producing plenty of waste water limit its application. The air-oxidation method with stibnite/jamesonite concentrate, sodium sulfide, and sodium hydroxide as the raw material and atmosphere as the oxidant is a newly developed method and its advantages are low production cost and the complex raw material can be treated by this method and its disadvantage is that the quality of sodium pyroantimonate is lower than that prepared by the oxidation method of hydrogen peroxide and the potash salt method.

Jan 1, 2006

By Enrique Posada

"The Valle de Aburrá area, corresponds to the city of Medellín and neighboring municipalities, with more than 3 million people. The area generates a sizable amount of solid waste, which has been taken to landfills for the last 20 years. This paper proposes a model for public policy making which considers the cost and benefit of different alternatives to handle the wastes in the coming 20 years. Combinations of several alternatives: Recycling, waste reduction, waste separation, incineration, land filling with lixiviate treating and gas energy recovery, and organic waste composting are considered and modeled and the results presented as a contribution for a more rational approach to policy making than the one currently being employed.IntroductionThe author, working for INDISA S.A., acted as a consultant for the direction of planning of the Empresas Varias de Medellín in 2004. This entity has the responsibility for the handling of the solid wastes of the city of Medellín and some of the neighboring municipalities. At the present time more the 700.000 annual tons of waste are taken to the site of La Pradera, located in very rainy location (3.000 mm of precipitation per year), with complex in topography and very far away from the sources of the waste. During the work the author detected important problems that should be addressed, as follows:Lack of adequate technical administration and resources. The entity did not count with sufficient human resources to focus on the appropriate technical handling of the solid waste. The organization worked mostly with independent contractors, lacking enough coherence and integration. The internal workload was too large for the few people who had technical responsibility and this gave rise to attention problems. It is important to have clear technical procedures, technical know how and human resources, continuity in the activities. It is important to have a clear capacity to plan, to study, to make tests and monitoring, to pursuit and develop ideas, to optimize the processes and to introduce changes, to respond to environmental authorities, to the communities and to mass media and to handle the contractors. All this was basically lacking. In the case of the handling of the sanitary filling of La Pradera, for example, although the people in charge were very able and dedicated, the magnitude of the task was too large and the resources they had were insufficient. As a result, the site had at the time of the study, problems with thousands of vultures, lack of immediate cover up for the waste, uncontrolled leaching, the area being dirty and little attractive, despite being called a park."

Jan 1, 2008

By A. N. Aposhian

The electronics industry generates tin/lead bearing by-products that can be recycled for their metal value. This paper will cover the processes used to recycle these tin/lead bearing byproducts from the plating, circuit-board fabrication and assembly industries. Though these processes are well known to the companies who do the recycling, few outside the industry including the generators of the by-products, understand the processes or needs of the industry. This paper will give a broad overview of these processes, and describe the services provided by this industry. The paper will also touch upon the future of the recycling industry, including the legislative and environmental push for the elimination of lead from electronics.

Jan 1, 2000

By Jack Thibodeau

During the past six years, most states have promulgated water quality regulations which contain numerical aquatic life standards for heavy metals. In addition, the Environmental Protection Agency (EPA) promulgated national water quality standards in 1992 which also include numerical aquatic life criteria for heavy metals. Numerous wastewater discharge permits have been issued by the states and EPA to industrial facilities which include low microgram per liter heavy metal limitations. In many instances, the limitations are below detection limits or treatability limits using state-of-the-art analytical methods or treatment technologies. This paper will discuss options for conducting studies, including the use of water-effect ratios, metal partitioning coefficients, and recalculation procedures to develop site-specific metals criteria and higher permit limitations. The installation of expensive metal treatment systems to remove trace metals may be avoided if higher permit limits are indicated by the site-specific studies.

Jan 1, 1996

By Alex Moyano

The Codelco-Chile is considering different processing options for the projected concentrate from the Alejandro Hales mine (former Mansa Mina mine with high arsenic and antimony content of 6% and 0.6%, respectively), that will produce complex blister copper with high impurities contents, higher than the present values produced at the converting process of the Codelco Norte smelter processing only Chuquicamata concentrates. In order to know both the anodic copper quality and the metallurgical implications when a complex blister copper is processed in the refining process of the CN smelter, the Codelco and IM2 ?task force? evaluated positively the refining process for the complex blister copper by addition of alkaline fluxes at laboratory and industrial scale tests. The promising results of the tests done at laboratory scale at the Tohoku University facilities, allowed a large scale test planning to validate the lab-scale results in 3 refining furnaces of 250 t capacity at the CN smelter. The obtained results demonstrate the industrial technical feasibility to process a complex blister copper in the refining furnaces producing an anodic copper quality suitable for the electrolytic process.

Jan 1, 2006

By V. A. Bryukvin

A hydroelectrochemical technology has been proposed and experimentally proven for processing metallic gold- and silver-containing concentrates on the basis of copper and copper alloys obtained as a result of preliminary physico-mechanical upgrading of electronic scrap. The proposed technology is based on hydroelectrochemical leaching of scrap using reversible electric current and diluted nitric acid solutions, containing complexing agents, permitting complete separation of gold from the nonferrous matrix without involving gold in the process, and dissolving copper, zinc, lead and tin virtually without any emission of nitrose gases.

Jan 1, 2006

By Barry T. Kilbourn

There is a continuous quest for better-performing materials, for example, to withstand higher temperatures, to resist more efficiently degradation or to be electrically conductive under extreme conditions. The oxides, and similar compounds, of the lanthanides and yttrium can, in some cases, help provide such behavior. Other advanced materials, such as hydrocarbon catalysts, optical ceramics or sensitive phosphors, may also require these oxides for some essential function. The role of the oxides in a wide variety of technologies, some novel and developing, will be reviewed and the underlying physico-chemical principles, the common threads, between several less well-known and apparently unrelated uses discussed.

Jan 1, 1989

By Han Ilhan

This paper discusses and describes aspects of a cost effective and safe tailings impoundment selection. In light of the current low metal prices and recent tailings embankment failures around the world, it is becoming extremely more important to develop tailings impoundment design that balance cost efficiency with safety. The paper will present critical design components associated with a tailings impoundment which need to be addressed during the planning phase. Procedures for identifying various tailings impoundment alternatives, and evaluation and selection of alternatives are presented.

Jan 1, 1999

By M. W. Wadsley

Despite the convenient subdivision of extractive metallurgy into hydro- and pyro- divisions, many flowsheets contain both types of process. When complex materials are used as feed, combinations of hydro- and pyro-metallurgical processes are even more common. Hydrometallurgy is used to treat many by-products and waste-products. (Bio-metallurgical processes may be considered to be a sub-set of hydro-metallurgical processes.) Combinations of the different processes in the Australian metallurgical industry are described. Selected international examples demonstrate that the use of combked processes is not a unique. Antipodean phenomenon. The motives for selection of combined pyre- and hydro-metallurgical processes in a flowsheet are examined.

Jan 1, 1994

By Luiz R. P. De Andrade Lima

This paper presents a mathematical model for the oxide copper ore heap leaching process. The data used in the model include physical-chemical, .geometrical and operational data, as: leachable metals ore contents, .flow rate and acid concentration, parameters of passivity, ore size distribution, the average residence time of the solution in the heap, height, irrigated area and weight of ore in the heap. In this model the heap is divided into horizontal and plane layers of constant area. The flow of the liquid in the heap is considered unidirectional and the solid-fluid reaction model is considered under diffusive control. The average residence time of the solution into the heap and the apparent effective diffusivity of the acid through the ore particles have .a significant influence on the rate of the copper extraction and its concentration in the pregnant solution; therefore these parameters are used in the model calibration. When this algorithm was applied to a laboratory test, the results showed that the model is adequate to predict the process performance.

Jan 1, 1999

By T. A. Venugopalan

The 'Hall-Heroult' Process of reduction of Alumina to Aluminium has remainded basically the same for over 100 years, but the technology has been undergoing drastic changes with respect to selection of materials for Cathode and Anode, and also energy consumption. The latest generation pots have a working life of about 1800-2000 days normally. After the failure of the pots, the Cathode Lining is dug out and disposed of on land. Since the lining contains objectional materials causing pollution, various processes have been tried for re-processing of this waste. However, most of the processes have been unsuccessful from the techno-economic point of view. At Hindalco a new chemical process for converting the fluorine values of the dug out material to Cryolite was developed in 1988 and a" one ton per day Cryolite production plant has been operating since 1989. This process is especially applicable where the integrated Alumina and Smelter Plants exist side by side. The experience in operating this Plant is discussed in detail in the paper.

Jan 1, 1992

By I. M. Santos Moraes

Achieving high current efficiencies when operating at high current densities is a goal for every refinery, whether conventional or permanent cathode technology is employed. To obtain higher current efficiency at increased current density at Caraiba's Tankhouse, the production team decided to change the cathode cycle from eleven to thirteen days, reducing cathode cycle to one per anode cycle. The idea was to reduce the anode-cathode spacing and consequently reduce the potential for short-circuiting them. With respect to current efficiency, the overall result was not much better than that obtained with the normal operating conditions. A new attempt to obtain higher current efficiency at high current density was implemented by going back to two cathode cycles per anode cycle, this time reducing cathode life to ten days. This approach yielded the highest current efficiencies. This paper presents the data generated with the three operating conditions: normal practice, a single cathode cycle per anode cycle, and two cathode cycles per anode cycle with a reduced cathode cycle time. It compares the productivity achieved with each set of operating conditions. An analysis of the main operating parameters as well as the advantages and disadvantages involved with each condition is also presented for future reference.

Jan 1, 1999