Search Documents

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By Guiming Yang, Xiaoxian Huang, Zhiyun Ji, Min Gan, Lishun Yuan, Xiaohui Fan, Zhiyuan Yu

"The roasting characteristics of hematite pellets containing MgO were studied where magnesia powder, serpentine and magnesite were used as magnesium-additives respectively. The mechanical strength of both preheated and roasted pellets decreased when MgO content increased, which implied the addition of MgO had an adverse effect on pellet consolidation. By adding flux containing CaO, the mechanical strength of both preheated and roasted pellets were improved. The addition of calcium flux facilitated the formation of calcium ferrite and provided a certain amount of liquid phase, resulting in faster diffusion ofMg2+ and Fe3+. The result showed that diffusing speed of Mg2+ was enhanced by 1.48 times, and rate constant of Fe203 crystalline growth was enhanced by 62% when basicity was around 0.4. Improvement of mineralization degree and recrystallization of Fe203 assisted in consolidation of hematite pellets containing MgO.IntroductionOxidized pellets are ideal iron-bearing burdens in blast furnace. At present, magnetite is the main raw material for oxidized pellet production in China. However, as the rapid development of iron and steel industry, resources of magnetite have been depleted and cannot satisfy the requirement of pellet production. Using hematite concentrates to produce oxidized pellets has become a trend [1, 2]. Many pellet enterprises abroad nowadays have adopted high proportions of hematite concentrates when producing oxidized pellets, e.g. the percentage is 100% in a lot of Brazilian factories [3, 4]. But high proportion of hematite concentrates will lead to low mechanical strength and high reduction swelling index of pellets. Some studies show that Mg-bearing pellets have excellent metallurgical properties, and the reduction swelling phenomenon can be solved by adding fluxes containing MgO [5, 7]. However, there are problems such as low pellet strength and bad roasting characteristics for MgO-bearing pellets, which remains an obstacle in pellet industry. Hence, it's vital to undertake the study on strengthening measures for indurations of Mg-bearing hematite pellets."

Jan 1, 2013

By Y. Z. Zhang

Electrochemical oxidation of arsenopyrite in ferric sulphate media in the absence and presence of bacteria T jerrooxidans has been investigated for the purpose of understanding the dissolution chemistry of arsenopyrite and the bacteria attack mechanism. Mixed potential, polarization resistance measurements, polarization curve, cyclic voltammetry experiments were conducted in a ferric sulphate medium of 10g/L FeH, temp.25-35°C, pH 1.5-2.5 in the absence and presence of bacteria Tjerrooxidans, respectively. For the anodic process, a two-step reaction sequence is suggested by the electrochemical measurements. The initial step at a low potential is described by:

Jan 1, 1996

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014

By Jayagopal Ucbil, M. Krishna, V. T. Vijayalakshmi

"The pitting susceptibility of aluminium metal matrix composites reinforced with garnet particles has been examined using static weight loss method by exposing the metal matrix composites (MMC) specimens to the action of IN HCI acid at laboratory temperature for different time intervals. It was found that the corrosion rate decreased with increase in weight percentage of reinforcement while the corrosion rate was a function of the matrix alloy but not of the reinforcement material. Further, it was found that the rate of corrosion was dependent on the interface region formed between the reinforcement and the matrix. A comparison of the base matrix with the corresponding composite when subjected to heat treatment for varying periods of 4, 8, and 12 hours respectively was made. The comparison revealed that corrosion resistance of the composite increased with the duration of heat treatment and this has established a considerable improvement in corrosion resistance of the composite when compared with the base matrix.IntroductionMetal matrix composites (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight [1-5]. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments [6-7]. Particles reinforced MMCs have been most popular over the last two decades. Among the MMCs, the most popular families are represented by aluminium reinforced with ceramic particles. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior."

Jan 1, 2000

By E. Bélisle, Christopher W. Bale, S. Petersen, C. Robelin, K. Hack, J. Melançon, G. Eriksson, A. D. Pelton, P. Chartrand, S. A. Decterov, I. H. Jung, A. Gheribi

The FactSage® package consists of a series of information, database and calculation modules that enable one to access pure substances and solution databases and perform thermochemical equilibrium calculations. FactSage was originally founded by process pyrometallurgists and has since expanded its applications to include hydrometallurgy, electrometallurgy, corrosion, glass technology, combustion, ceramics, geology, environmental studies, etc. With the various modules one can perform a wide variety of thermochemical calculations and generate tables and graphs of complex chemical equilibria and phase diagrams for multicomponent systems. This paper presents examples of recent and current developments in FactSage in areas of particular interest to Dr. David Robertson. These include both ferrous and non-ferrous processing, as well as solidification and refining simulation. The paper also includes reference to the Internet Fact-Web education package.

Jan 1, 2014

By Guo Chen, Yifeng Shi, Xiaobiao Shang, Nanshang Shen, Bangqi Zhang, Jinhui Peng, Junruo Chen

"The energy is introduced directly into the volume of the honeycomb ceramic regenerator due to the complex interaction of microwaves with minerals in microwave gas heating system. A three-dimensional numerical model is developed to simulate the electromagnetic field by solving Maxwell's equations using finite-difference time-domain method. Computational result is presented for the microwave power absorption of the regenerator. Effects of the dielectric constant and the effective loss factor on the microwave power absorption in the regenerator are studied as well. Numerical results show that the heating pattern strongly depends on the dielectric property of the regenerator. The demonstration of the model of electromagnetic field distribution can be applied effectively and efficiently to optimize the fundamental parameters in the microwave heating processing.IntroductionIn recent years, microwave energy has been utilized in many fields, such as food processing, chemical engineering and mineral processing [l]. In contrast to conventional heating, where heat is transferred from a surface to the interior, microwave energy is introduced directly into the volume of minerals due to the complex interaction of the microwave with the mineral. Based on volumetric heating effects, microwave heating has several advantages such as pollution free, rapid heating technique, internal heating, high efficiency over conventional heating [ 1-4]."

Jan 1, 2013

By Zhen Zhang, Jiang Diao, Tao Zhang, Yi Ren, Lu Jiang, Xiao-Man Yan, Bing Xie

The precipitation behavior of phosphorus enrichment phase was investigated by slag modification with Al2O3. The mineral phase of the original slag and modified slags were measured by mineral phase microscope, SEM+EDS and XRD. The mechanism of Al2O3 modification was discussed according to the thermodynamic theory analysis software (Factsage version 6.3). The results show that the high phosphorus solid solution (nˊ2CaO·SiO2-3CaO·P2O5) was generated by the continuous reaction of nC2S-C3P (nˊ＜n) solid solution and Al2O3 under 1350℃. The amount of initially precipitated solid solution (nC2S-C3P) was reduced and even disappeared with the increasing of Al2O3. If the addition of Al2O3 is enough in the slag, the high phosphorus solid solution (nˊC2S-C3P) that generated by the above mentioned reaction will continue to react with Al2O3 to produce Ca2Al2SiO7 and even C3P, which was demonstrated that the addition of Al2O3 has a positive influence on the precipitation of phosphorus enrichment phase.

Jan 1, 2015

By T. T. Chen

Canadian Electrolytic Zinc has developed the "cement-stabilization of jarosite residue" Garofix) process to stabilize zinc plant jarosite residues for disposal. The cement-jarosite mixtures cure quickly, have good mechanical strength and low hydraulic permeability; they possess good neutralizing capability and chemical stability. In the jarofix process, Portland cement partly decomposes jarosite to form (SO4MOH)12.nH2O, ferric hydroxide and an alkali sulphate. Approximately 40% of the jarosite reacts in mixtures containing 30% cement. The jarofix product also contains various Ca-Al-Fesilicate-sulphate-hydrate phases and gypsum, which bond the individual particles together imparting mechanical strength and reducing the permeability. Most of the reactions take place in the first few hours of curing. Ammonium jarosite is slightly more reactive than sodium jarosite but releases NH3 gas; water-soluble Zn in the jarosite residue is stabilized in the cement reaction products.

Jan 1, 1996

By J. M. Casas

This work presents the development of an ionic equilibrium model and its use to simulate the distribution and concentration of chemical species (speciation) in sulfuric acid - cupric sulfate solutions in the 0-2 pH range, 0.1-10 gpl copper concentration range and 15-45°C temperature range. The model consists of a set of equations which represent the equilibrium relationships for the ionic reactions and the mass balances for the components present in the system. The effect of ionic strength was taken into account by correcting the equilibrium constant in concentrated solutions. Several species can be formed at different pH and temperature values, the principal being: HSO-4, SO42-, CuSO4(aq), Cu2+, and H+ in order of increasing solution acidity. Simulations show that concentrations are highly dependent on pH. The sulfuric acid speciates mainly as bisulfate ion (HS0-4) and hydrogen ion (H+) at pH values lower than 1. The model presented in this work can be applied to predict and analyze the solution composition in electrolytic copper processes such as electrowinning, electrorefining and electrodialysis, as well as the purification of various industrial solutions.

Jan 1, 1999

By Tseng. B. H.

Samples of unchlorinated and chlorinated carbonaceous concentrate from a carbonaceous gold ore were analyzed by transmission electron microscopy (TEM) for organically bonded sulfur and chlorine. The concentrate assayed 1.53 oz/t gold and 6.01% organic carbon. Much of the organic carbon occurred as sizable coarse particles up to several hundred microns in size, which showed no visible evidence of reaction with chlorine after chlorination treatment. Both the untreated and chlorinated fractions of the carbonaceous concentrate were analyzed by the TEM method, which detected organically bonded sulfur in all of the carbon particles examined in the untreated sample, ranging from about 1 to 5% organic sulfur, and averaging near 3.1%. TEM analysis of 40 carbon particles in the chlorinated sample indicated that organic sulfur was reduced significantly in the carbon and replaced in part by the chlorine, as the result of chlorination.

Jan 1, 1987

By Lin Li, Wen Shi, Hua Wang

"Specimens of the ultra-low carbon bake hardening steel were soaked for 1 min to 5 min, and then cooled by water quenching. The internal friction experiments were carried out to detect the spectra of the specimens. Results show that Snoek peaks are present in all the specimens, however, an obvious Snoek-Koster peak is found only in the 5 min-annealed specimen. Besides, tensile results indicate that the bake hardening values increase with the annealing time prolonging from 1 min to 3 min, but decrease as the annealing time prolongs further to 5 min. The solute distributions in the specimens were characterized by three dimensional atom probe. Some segregated C and V are found in the 1 min-annealed specimen, and the C and V contents decrease as annealing time prolongs to 5 min.1. IntroductionAs an excellent member of automotive body panel materials, various types of bake hardening (BH) steels have been developed since 1980s. Bake hardening property, as one of the most important mechanical properties, has been studied by many researchers [ 1-5]. As is known, BH phenomenon is generally controlled by the interaction between solute C and dislocations. The Snoek peak of internal friction (IF) is very popular in the investigation of solute C [6-9]. However, result of internal friction cannot suggest the distribution pattern of solute C as well as its influence on BH phenomenon.Three dimensional atom probe (3DAP) can diagnose solute element atoms as well as nano-sized precipitates, and it is the only instrument that currently can identify the identities of individual atoms in a material and measure their spatial coordinates with the resolution close to 0.3 nm [10]. There have been a number of studies about using 3DAP to detect solute elements as well as nanometer sized precipitates [11-19]. For example, Hono et al. [16] used 3DAP to determine the solute elements in an age-hardened Mg-Ca-Zn alloy, and they also obtained the distribution patterns of the observed elements."

Jan 1, 2011

By I. Gaballah

Decontamination of synthetic solutions of PbC12 containing 10, 100 and 1000 ppm of lead, using chemically treated barks had been studied. The percentage of !cad cations' removal from solutions depends upon the pH and the initial concentration. About 99 % of the initial lead content can be removed at pH of about 3.5, 5.5 and 6.5 for initial concentrations of 10, 100 and 1000 ppm respectively. The maximum retention capacity of the treated bark is about 83 mg of lead per gram of modified bark. Bark loaded with lead had been analyzed by Infra Red spectroscopy. It seems that lead reacts with hydroxyl groups of the phenolic constituents of the bark. On the other hand, the removal of a lead cation by the bark leads to the release of two H+. This seems to show that the removal of lead could be interpreted as an ion exchange with hydrogen belonging to the hydroxyl groups of the modified bark.

Jan 1, 1994

By Andrew L. Puwis

Methodologies were presented for computing the thermal gradient associated with single crystal solidification in macroscopic computer modeling. The. heat transfer, and solidification of a shaped investment casting model were simulated using properties from three different alloys. Following the simulation of solidification, the resultant thermal gradients (G) and rates of solidification (R) from representative points were extracted in various ways and compared: It was discovered that alloy properties have a strong influence on the computed thermal gradient and rate of solidification for the three methods investigated. Data also showed that the computed gradient for each model was very different depending on the temperature range used to compute these values.

Jan 1, 1994

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By Zhang Yongzhu

In hydrometallurgical processes of PGMs separation and refining, differences between 1-PGMs (Ru;Rh;Pd) and h-PGMs(Os;Ir;Pt) in thermodynamics and kinetics have been observed. The successful practice in the separation and refining of PGMs in China, is mainly based on the following two kinetically extraction sequences of: (1) for the extraction of PGMs complexes in different configurations with coordination mechanism (AuCI,) -> (MCl6)2-> (MCl4 )2-> (MCI6) 3- , and the substitution rate for h-PGMs complexes with higher effective nuclear charge Z' is much more slow than that of I-PGMs. and (2) for the extraction of PGMs in different configurations with oxonium (or ion -exchange) mechanism (AuCl4)-> (MCl4)2--> (MCl6)2-> (MCl6)3- and the extraction of h-PGMs complexes with low surface charge density is more fast than that of I-PGMs complexes. In view of atomic structure theory, the similarity of atomic radii and chemical properties and difficult separation of PGMs resulted from the Lanthanide Contruction between 5th period (1-PGMs) and 6th period (h-PGMs). The differences between h-PGMs and 1-PGMs are due to the loss shielding of 4f subshells on 5d electrons for h-PGMs with higher nuclear number, which makes h-PGMs have a higher Z' (effective nuclear charge) and strong attraction for outer space electrons. As a result, h-PGMs metals and complexes are thermodynamically more stable and kinetically more inert than the corresponding 1-PGMs. The differences between h-PGMs and 1 -PGMs in aspects of elements properties, complexes, hydration, substitution and redox reactions , are discussed.

Jan 1, 1993

By Md. Maniruzzaman

The quenching performance of a liquid quenchant can be controlled by controlling the agitation in the quench tank. Without agitation, a vapor layer or bubbles form at the hot part surface and the natural convention of the quenchant limit the heat extraction rate at the quenched part surface. Resistance to the heat extraction rate can be reduced by breaking the vapor layer or by inducing a turbulent convection at the part surface through agitation (Le. forced circulation of the quenchant). To determine the effects of agitation on the quench performance of a mineral oil based quenchant, the CHTE quench probe system was used with AISI4140 steel probe tip. Quenching performance of the oil is evaluated by computing the effective heat transfer coefficients of the steel probe as a function of surface temperature using Lumped Parameter Analysis. In addition, computational fluid dynamics (CFO) simulation of the quench tank with an impeller type agitator has been done to understand and predict the fluid flow pattern in the tank. CFO simulation also provides insights for determination of optimal location of the impeller and the quench probe tip. Keywords: CHTE Quench Probe, agitation, CFD simulation, liquid quenchant, 4140 steel

Jan 1, 2003

By Noel A. Warner

Modern steelmaking is based on direct use of oxygen in high intensity batch reactors. A totally new approach is proposed in this paper, based on the view that pursuit of high intensity is unlikely to lead to successful coal-based continuous steelmaking. By substituting carbon dioxide and water vapor as the oxidants rather than using oxygen directly, the intensity is greatly reduced. Accordingly, subsurface formation of carbon monoxide bubbles can be avoided by careful manipulation of the three participating rate processes, gaseous diffusion, interfacial chemical kinetics and liquid phase mass transfer. Steelmaking can then be carried out without explosive ejection of molten droplets and the generation of micro-spray but rather in a controlled and fume less fashion. The vital component is the introduction of generic melt circulation technology. Three melt circulation loops in series are envisaged. Starting with a composite feed of iron ore fines, pulverized coal and lime flux, a metallized solid raft floating on molten iron is propelled out of the ironmaking loop onto the first of two downstream steelmaking loops. In the first, a liquid slag is formed, primary decarburization is undertaken not with oxygen but rather with CO2 and H2O and the melt is desulfurized. The semi-product stream enters the third melt circulation loop, where open-channel decarburization is effected along with dephosphorization to yield a low carbon steel product. Alternatively, the melt leaves the last loop to irrigate a packed tower countercurrent to argon at around 100 mbar to continuously produce ultra-low carbon (ULC) steel.

Jan 1, 2003

By P. Kerr

Iron segregation is pre-dated by copper and nickel segregation processes for which the experimental methodology and reaction chemistry were established. The accepted reaction sequence for segregation involves the generation of hydrogen chloride, the chloridization and volatilization of the metal chloride, and precipitation of the metal from the metal chloride in the vicinity of carbon. Iron segregation roasting offers a potential extraction solution for processing oxide deposits with complex mineralogy or waste streams such as Minette-type iron deposits, nickel laterites, ilmenite, red mud, electric arc furnace (EAF) dust, mill scale and slag. After subsequent magnetic separation, one is left with a high grade metallic iron powder which can be marketed for powder metallurgy or briquetted to serve as a direct reduced iron (DRI) product. The non-magnetic product is typically concentrated oxides including rutile, alumina, or oxides of V, P, and rare earths, etc. that may be economically recoverable with subsequent processing. While operating conditions vary for different metals, they share the requirements of an elevated operating temperature and a mixture of oxide ore, carbonaceous additive and a chloride additive in varying amounts all in a closed reactor to allow for reducing conditions and contain the volatile chlorides. This process is then followed by some form of physical separation. Testwork performed by the authors shows promising results that may aid in future development of the process. Segregation roasting of iron will likely never displace traditional beneficiation and ironmaking technologies; however, it has great potential in niche markets where traditional technologies have failed or current technologies generate substantial waste.

By Finlay Campbell

Nickel laterite pressure acid leach plants and reduction roast plants have had a checkered history in their engineering, construction, startup and operational reliability. Many potential projects have been the subject of detailed studies over the last thirty to forty years but relatively few have advanced to commercial production. Four reduction roast plants are currently operating, an additional one was partially constructed but never completed, and another was started up in 1974 and shut down after 12 years operation. Three acid leach plants have been built and commissioned in the last five years, trying to follow the example of the Moa Nickel plant in Cuba. An additional acid leach plant project is currently on hold, following limited construction work, its future subject to review by the owner because of potential cost over-runs. This paper attempts to discuss difficulties that may be encountered as a project is developed and will address factors which may affect production ramp-up schedule, long term production performance and overall production success. Comparisons are made with ramp-up performance at other large metallurgical plants that employ some comparable unit operations. Keywords: Caron, PAL, nickel laterite ore, ramp-up, reliability, process development, equipment design, step-out, commissioning, startup.

Jan 1, 2004