Search Documents

By Zachery Zanetell

Flotation circuit performance has become increasingly more challenging due to the complexity of available ore sources. To optimize value mineral recovery, the mineralogical composition of the ore should be evaluated and understood. Utilizing a variety of mineralogical and analytical tools, flotation processing challenges can be overcome and potential limitations understood. In this paper, several case studies will be discussed in terms of the value that has been provided through the use of mineralogical analysis to optimize flotation performance.

By John C. Carpenter

Solvent extraction is used to selectively recover copper from iron containing sulphate solutions. As chloride ions, which form series of complexes with transition metals, are now being used for leaching. Little is known of the effects of these ions, on solvent extraction behavior. It has been shown that commercial extractants of the L1X and Kelex series extract copper from chloride media: (1) at a lower pH than from sulphate solutions, (2) to similar loadings, and (3) except for L1X 63, without transferring chloride to the organic phase. A process for selective extraction of copper from chloride solutions should thus be compatible with standard stripping and electrowinning practice. Of several diluents, differing in aromaticity, kerosene gave enhanced extraction only with L1X reagents. A change in operating temperature had little effect on equilibrium metal distribution. All the extractants examined gave adequate separation of copper from iron. L1X 63 was found to extract chloro-complexes of copper and of iron and thus transfer chloride to the organic solution. Consequently this extractant and its mixtures are not preferred for use with chloride leaching systems.

Jan 1, 1976

By Yuzura Sato

Viscosity has been measured for various molten binary alloys of nickel with iron, cobalt and chromium in order to clarify the behavior of viscous flow of molten nickel alloys. The entire concentration range for iron and cobalt and 0-67at% of chromium content were studied. The measurement method was an oscillating cup viscometry using an alumina crucible that was precisely machined. The temperature was up to about I 880K for all the measurements. The results represented good Arrhenian relationship although some measurements included overcooled temperatures. The isothermal viscosities increased monotonously with an addition of iron and chromium into nickel. The addition of cobalt increased after stationariness. The isothermal viscosities showed concave curves. Activation energies increased monotonously by adding all the elements into nickel. These phenomena were considered to be related to the thermodynamic properties 'such as the heat of mixing and the structures of mixture melts.

Jan 1, 2003

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.

By Lanre Oshinowo

Computational Fluid Dynamics (CFD) is used in conjunction with process modelling at HATCH to achieve a superior level of confidence in the process design of hydrometallurgical process plants. The use of these tools to evaluate designs through virtual prototyping reduces the risks associated with making design decisions. This paper highlights the development of a co-simulation strategy at Hatch for the seamless integration of process modeling software addressing different scales (process time and space): flowsheet level models and .equipment level models. With co-simulation, the process design engineers can improve design accuracy, troubleshoot and optimize performance and influence decisions impacting equipment operation by representing specific unit operations in the flowsheet model software with detailed CFD models. Specifically, this paper will focus on the co-simulation of a Ni/Co high-pressure acid leach (HPAL) process including heaters/heat exchangers and flash system, autoclave and quench/scrubber system. The knowledge developed can be transferable to other processes.

Jan 1, 2004

By Lichao Ding, Jingbiao Fan, Yunnen Chen

"With the development of industrial production, more and more wastewater containing high concentration ammonia nitrogen was discharge into the environmemt, which caused serious harm to the environmemt. Treating the wastewater has great significance to protect water resources. Using air-stripping combined with oxidation to uptake high concentration of ammonia nitrogen wastewater. The influence of operating parameters was investigated. Experimental results revealed that pH of solution, aeration time and aeration strength showed heavy influence on ammonia nitrogen removal. Air-stripping combined with oxidation can be considered as an alternative approach for the removal of high concentration of ammonia nitrogen from practical metallurgical wastewater. When pH was 11, aeration time 20 min, aeration strength 1040 Lh-1, and oxidation with 10 % NaClO solution 10 min, the initial ammonia nitrogen 2130 mgr1 could reduce to 12 mgr1. Other items could also be removed to meet the ""Integrated wastewater discharge standard (GB8978-88)"".1. IntroductionThe rapid development of human activities has caused a worldwide increase of nitrogen in rivers, lakes and coastal waters. It leads to considerable eutrophication and an increase in the frequency of toxic algae blooms [1,2]. The concentrations of nitrogen in the water of China are pervading high [3]. The discharge of wastewater containing high concentration of ammonia nitrogen is one of the most important factors. Great efforts have been devoted to the removal of ammonia nitrogen from wastewater. Traditional methods include biological denitrication [ 4 ], chemical precipitation with magnesium ammonium phosphate [5], electrochemical conversion [6], air-stripping [7] and so on. Biological denitrication is the most common process in the treatment of ammonia nitrogen wastewater. But the process is only suitable for the removal of relatively low ammonia concentration due to the requirement of appropriate C/N ratio [8]. Chemical precipitation needs additional reagents, which may introduce new pollutants to water body. Electrochemical method often uses expensive metal or metal oxide as electrodes, and also consumes large quantity of energy [6].Although air-stripping makes use of stripping tower and consumes energy, it is very suitable for the removal of relatively high ammonia concentration. Different air-stripping conditions would appear different removal efficiency. And only air-stripping the effluent can not be attained the ""Integrated wastewater discharge standard (GB8978-88)"". In this study, we use air-stripping and oxidation to removal high concentration of ammonia nitrogen from simulated and real ammonia nitrogen wastewater."

Jan 1, 2011

By V. G. Papangelakis

The implementation of a flow-through yttria-stabilized zirconia (YSZ) sensor for pH measurements in high temperature and concentrated electrolyte systems relevant to hydrometallurgical processing of nickeliferous laterites is discussed. Instrumentation involved the use of a custom made flow-through titanium electrochemical cell. Accuracy and validity of the pH measurements at temperatures up to 250C were assessed using concentrated sulphate process solutions ranging from synthetic binary sulphuric acid ? water solutions to progressively multicomponent metal ? sulphate solutions simulating laterite Pressure Acid Leach conditions. The measurements were also compared with theoretical models using recently obtained thermodynamic data. A difference of ±0.25 pH units was observed between measured and calculated pH values at temperatures. This is an acceptable difference given that these are the first direct high temperature pH measurements ever on the concentrated acidic sulphate solutions. This result is encouraging more research for the development of industrial electrochemical systems for direct pH measurements in autoclaves.

Jan 1, 2003

By S. M. Copley, M. Yankova, E. Y. Yankov, J. A. Todd

"Nanophased coupled growth structures, with spacings of -10 nm, have been observed in banded microstructures produced by laser melting hypoeutectic Ag-Cu alloys. These coupled growth structures comprised a Cu-rich phase of width - 1 nm and a Ag-rich phase of width - 9 nm. In this paper, microstructural observations of nanophased coupled growth structures in hypo eutectic AgCu alloys are presented. Laser beam velocities for the transition from banded to microsegregation free microstructures are modelled and compared with experimental values. Models are presented to show that, at a critical undercooling, initial growth of a Ag-rich, metastable, extended solid solution is rapid but slows to a halt as copper is partitioned into the liquid at the solid/liquid interface. Following nucleation, the coupled growth structure then grows until the partitioned copper is consumed, at which point growth of the Ag-rich solid solution is again accelerated. This cycle then repeats resulting in banded microstructures comprised of 750 nm of the Ag-rich extended, metastable solid solution, followed by 250 nm of the coupled growth structure.1. Structural Studies of Laser Melted and Resolidified TrailsPresented here are observations of laser melted and resolidified trails in Ag-Cu alloys obtained at beam velocities ranging from 0.7 to 34 cm S·I. When the laser beam is scanned along the surface (positive x-direction) with a velocity Vb a melt pool with the shape given in Fig. 1a moves with the beam. The isotherms move with the velocity, Vi,. = Vb cos.p. Calculations employing the thermal analysis of Kou, Hsu and Mehrabian [1] for the beam velocities of this investigation and for the thermal properties of AgCu alloys, indicated that, .p, the angle between the isotherm velocity and beam velocity should be small at the surface where microstructural studies were made. This prediction was supported by observations of trail cross-sections. Based on these observations, and the calculations which include latent heat effects, the isotherm velocity for observations near the surface in our investigation was taken to be 27 cm S-I."

Jan 1, 1994

By D. H. H. Quon

Results of a study conducted to determine the properties of iron ore pellets made from Mount Wright and Carol Lake ore concentrate fines with partial and full substitution of bentonite by several organic binders are presented. Carboxy methyl celluloses 7H and 6TL, hydroxy ethyl cellulose (natrosol) and modified guar gum all produce pellets of acceptable wet, green and dry strength. However, when fully substituted, an inorganic binder such as calcium carbonate is required for satisfactory strength development after induration. Mixing the Carol Lake ore with Mount Wright ore in a 50-50 ratio also achieves the same result. The failure of the Carol Lake ore in the pelletization process is attributed to the low hematite content of the ore. The results are very similar to those from the extrusion studies reported earlier (8).

Jan 1, 1989

By Yoji Imai, Akio Watanabe, Masakazu Mukaida

"To clarify the feasibility of alkoxides and acetylacetonates as precursors for laser CVD of metal oxides, vapors of tantalum or titanium alkoxides and zirconium acetylacetonate were irradiated by KrF excimer laser and deposits were characterized by XRD and XPS measurements. As for tantalum and titanium, non-stoichiometric crystalline oxides grew nearly phototropically, however, zirconium oxides deposited showed only halo-pattern by XRD measurements. Electric conductivity measurements of tantalum oxides implied the improvement of the insulating properties by the addition of activated oxygen to the ambient.IntroductionThere has been renewed increasing attention to the metallic oxide thin films because ofits promising usefulness in many applications, such as high-Tc superconductors and ferroelectric devices. A variety of thin film preparation techniques have been studied such as sputtering, chemical liquid deposition (sol-gel and metalorganic decomposition), pulsed laser deposition and chemical vapor deposition (CVD). Among them, we think CVD is the most promising method because it offers a high controllability of morphology and good step coverage at relatively high growth rate. Preparation of oxide films by CVD can be achieved using a precursor containing metallic element and oxygen containing gas such as N20 at the same time. However, metalorganic (MO) compounds which contain both metallic element and oxygen, directly bonded to metallic element, seems to be more favorable because some of MO has a good properties for CVD such as a rather high vapor pressure, stability in ambient and low toxicity."

Jan 1, 1998

By I. D. Reznik

Regularities of cobalt and nickel distribution between slag and matte, slag and metallic alloy on the base of concepts on exchange reaction equilibrium are considered. It is shown that the distribution of cobalt and nickel in industrial processes approaches to equilibrium one. Oxysulphiae influence on the bahaviour of cobalt, nickel and sulphur is shown. The recommendations on conduction of the processes of smelting, converting and slag cleaning based on the analysis of the methods or" non : ferrous metal separation from iron are given.

Jan 1, 1993

By Zdzislaw Miczkowski

At KGHM Polska Miedz S.A, a direct flash smelting process is used for smelting of chalcocite concentrate for the production of blister copper. The paper presents a model of complex oxidation process of single concentrate grains smelted at KGHM. The description covers main chemical reactions, phenomena of heat and mass exchange inside the grains and between a grain and the surrounding space. In the model, two zones describing the course of process inside the grain were distinguished: ? The first one, which moves faster towards the centre of a grain, both organic and carbonate carbon are freed, The process takes place without the presence of oxygen and results in an increase of the temperature in the core of the particle. ?The second zone moves slower into the grain and the rate of the movement is determined by the presence of oxygen, In that zone the sulphur is eliminated and the oxidation of the organic compounds vapours moving from deeper layers of a grain takes place. Based on the results of laboratory tests, the coefficients that describe the oxygen transportation into the grain and decide the progress in the chemical reaction were determined, The paper contains the results of model calculations for single grains reacting in environment of various content of oxygen as well as the results of model calculations for the laboratory reactor system.

Jan 1, 2003

By A. Navarra

Peirce-Smith converting (PSC) is applied for roughly 50% of primary nickel and 70% of primary copper production. PSC cycles produce batches of ironfree sulfide matte (or blister copper, in the case of copper smelters), that are subject to further processing. However, the number of cycles that can be performed simultaneously is limited by the offgas handling system. Moreover, PSC suffers from variation in the yield and duration of the cycles. This variation is managed by conventional smelter designs, in which the upstream smelting capacity exceeds the nominal converting capacity; PSC is thus a major bottleneck in conventional nickel and copper smelters. Stabilization and standardization of PSC operations can therefore increase smelter throughput. The current paper presents a discrete event simulation (DES) framework to assist in smelter debottlenecking. It features random number generation to represent cycle variability, and time-adaptive finite differences to represent thermochemical complexity. Preliminary computations are presented.

By R. David Prengaman

During the past several years a new insoluble lead anode has been developed for copper electrowinning. The new anode consists of a rolled lead-calcium-tin alloy sheet attached to a slotted copper bus bar by a soldering process which produces a complete metallurgical bond between bar and sheet. The metallurgical bond greatly reduces the resistance between the bus bar and the lead sheet and the high conductivity does not deteriorate during the life of the anode. The rolled anode thins uniformly and does not suffer preferential grain boundary or internal corrosion commonly seen in cast anodes. The lead-calcium alloy containing a high tin content corrodes slowly because the rolling process produces a uniform, fine grained structure. The wrought product is very strong and ductile; and contains no internal defects, segregation, cracks, or pores which can reduce the life of the anode. Because the anodes corrode uniformly, a high percentage of the anode thickness can be utilized thus extending the life of the wrought anodes. The anode alloy composition which is stable only in wrought form, produces exceptional resistance to passivation during current interruptions. First introduced into liberator cells, the new electrowinning anodes have been specified as the anodes of choice for every new SX-EW tankhouse constructed in the last two years. This paper describes the new anode, its method of construction, service history, and how it differs from present copper electrowinning anodes.

Jan 1, 1987

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987

By Sue Ritz

Gold extraction has relied on coconut carbon in adsorption circuits for several decades. IXOS®, invented by 6th Wave Innovations of Salt Lake City, Utah, is a new type of adsorbent that exceeds the selectivity of carbon and improves on the mechanical properties of other available resins. IXOS selectivity against copper cyanide complexes allows it to be used in circuits that currently struggle with copper contamination. IXOS potential to eliminate or reduce the application of SART technology will expand the opportunities to exploit more complex precious metals deposits. This paper will describe the technology behind IXOS molecular imprint, its comparison to carbon adsorption in the field, and the effect of efficiency on long-term recovery from heap leach METSIM simulation software.

Two pilot-plant investigations were conducted in which strong-base resins were compared with activated carbon for the extraction of gold cyanide from leached pulp from the Golden Jubilee Mine. The results show that gold can be recovered with carbon, but that the extraction efficiency is poor, probably because high concentrations of humic and fulvic acids are. present m the pulp. .However the extraction of gold cyamde from this material with strong-base resins JS very effo:1ent, and the overall efficiency of extraction is better with resin than with carbon, even when the concentration of resin is one-third that of carbon, and the flowrate of resin is one-third that of carbon. The results of the pilot-plant campaign reported in this paper led to the conversion of the Golden Jubilee plant from carbon-in-pulp to resin-in-pulp in February 1988.

Jan 1, 1989

By H. Y. Sohn, M. Y. Mohassab-Ahmed

"As part of research to develop a novel flash ironmaking process using reduction of iron ore concentrate by natural gas or hydrogen, sulfur and phosphorus distribution ratios between MgOsaturated slag and iron were determined in the temperature range 1550-1650°C under three different gas atmospheres: H2/H2O, H2/H2O/CO/CO2, and CO/CO2. The distribution coefficients of sulfur (Ls) were 4.0, 2.0, and 0.8, respectively, under these atmospheres. The distribution coefficients of phosphorus (Lp) were, respectively, 8, 17, and 20 under these atmospheres. In the flash process over -25 wt% P and S volatilize during ore concentrate downward flight in the reactor shaft in addition to avoiding coke. Therefore, iron produced by the flash ironmaking process would have much lower sulfur contents than the typical hot metal produced by the BF.IntroductionGiven the issues related to large carbon dioxide emissions and energy consumption in the existing ironmaking technologies, a novel flash ironmaking technology was conceived by Sohn [1-3] at the University of Utah. This technology is the first ironmaking process that will convert iron ore concentrate directly to metallic iron in-flight. This process will produce iron directly from concentrate without requiring pelletization or sintering and avoid the need for coke. In addition, this process concept takes full advantage of the fine particle size of concentrate with a large surface area, which permits rapid reduction by a gas. In this novel ironmaking process, potential reductants and fuels are H2, natural gas, and coal gas. Therefore, an iron-slag bath is expected to be at equilibrium with gas atmospheres of mainly H2/H2O or CO/CO2/H2/H2O, respectively, corresponding to the use of H2 or natural gas/coal gas. Since the effects of an H2O- containing atmosphere on slag properties have not been studied before, it is critical for the development of the novel flash process to determine these effects. In H2-H2O-CO-CO2 gas mixtures under ironmaking conditions, H20 was found to have the most pronounced effect on the slag chemistry [ 4, 5]. In addition, it was found in this laboratory that water in the gas atmosphere affected the distribution of Mn between slag and molten iron [6]. Most previous work used CO/CO2 gas mixture to control oxygen partial pressure (p02) [7, 8]. Others used only inert atmospheres [9], although Kor and Richardson [10] used a mixture of C02/H2 to control p02. For phosphorus, previous research focused on Ar [11], Ar-CO mixture [12], CO [13], CO/CO2 [14] or N2/CO [15]. Therefore, it was necessary to investigate the effect of water vapor content in H2-H2O-CO-CO2 mixtures on the equilibrium distribution of sulfur and phosphorus between CaO-MgOsatSiO2-Al2O3-FeO- MnO (0.2-0.8 wt%)-P2O5 (0.1-0.9 wt%) slag and molten iron as part of the development of the novel flash ironmaking technology."

Jan 1, 2014

By Dalene Joalet Steenkamp

Excavation of industrial-scale furnaces allows for the systematic study of reaction sequences by identifying the different reaction zones within the furnace. In 2013, Transalloys excavated a 48 MVA submerged arc furnace that was used for silicomanganese production using the ore-based route. The excavation method was reported elsewhere as was observations made in terms of refractory wear and modes of electrical energy dissipation prior to excavation. The paper presented here, reports on the process reaction zones observed during the excavation and subsequent phase chemical analyses of a number of process samples obtained during the excavation. The zones identified were a loose burden zone, a dry coke-bed zone, a wet coke-bed zone, a hard build-up zone, and an alloy zone. The results are compared to observations made in the excavation of an industrial-scale SAF and a pilot-scale SAF in Norway. The presence of the hard build-up zone below one of the electrodes and absence of a slag zone below all three electrodes are unique features of the SAF excavated at Transalloys.

By Yuanbo Zhang, Zhaokun Tang, Mingjun Rao, Guanghui Li

The ballability of hematite ore with addition of a certain amount of pulverized anthracite and the induration features of anthracite–containing hematite pellets were studied. The results indicate that adding a certain proportion of anthracite can improve the quality of green pellets as well as the roasting performance of roasted pellets. The suitable mass dosage of anthracite is 1.0%–1.5%. Under the conditions of roasting temperature 1280 oC–1350 oC and roasting time 15 min–20 min, the compressive strength of roasted pellets is found to be more than 2500 N/P. Compared with hematite pellets in the absence of anthracite, the proper induration temperature is diminished by 20 oC, whereas optimal induration temperature range expands by 50 oC, and induration time is shortened by 5 min–10 min. Adding anthracite is an effective measure to improve the pelletization of hematite.

Jan 1, 2015