Search Documents

By Harry Verakis, Thomas Lobb

Over the past decade, approximately 5.1 billion pounds of explosives were used annually, on average, in the United States. Most of the explosives were used by the mining industry. The coal mining industry was and still is the dominant user of explosives. About two-thirds of the explosives consumed was used in coal mining.

Jan 1, 2003

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By Jeffrey A. Pontius

The Cresson gold deposit is in the southcentral portion of the Cripple Creek mining district in central Colorado (Fig. 1). The deposit is hosted by a series of 32 Ma (Kelley, 1995) felsic to mafic, alkaline volcanic rocks that were deposited in a diatremal environment. Mineralization in the Cresson deposit is structurally con-trolled. It occurs as disseminated and vein type. Gold deposition is closely associated with potassium-pyrite metasomatism and quartz-telluride vein development(Pontius, 1992). The Cresson deposit is owned by the Cripple Creek and Victor Gold Mining Co. (CC&V), a joint venture between Pikes Peak Mining (67%) and Golden CycleGold (33%).

Jan 1, 1996

By F. Díaz-Fierros, D. Rubinos, M. T. Barral

The present work explores the reutilization of red mud, an industrial waste arising from the production of alumina, as a component of isolation technologies for hazardous substances. The work involved the study and optimisation of the geotechnical properties of red mud in conjunction with adsorption experiments of As(V) and Hg(II). The results from both types of experiments were integrated in a dispersion-diffusion model to calculate migration curves and minimum thickness of the red mud compacted layer. The geotechnical studies showed that compaction increased the stability and decreased the hydraulic conductivity of red mud barrier. Red mud sorbed high amounts of As (up to 44 mmmol kg-1) and Hg (up to 9.2 mmmol kg-1). The calculated minimum thickness of the red mud barrier was 1-10 cm for As and 2-19 cm for Hg, for an operation period of 35 years. The results obtained let to conclude that the reuse of red mud as a component of isolation systems of hazardous substances represents a viable alternative use of this residue.

Jan 1, 2011

By Ove Alm

Wet and dry specimens of three rocks of approximately granitic composition were deformed at different experimental conditions. These experiments were carried out in order to study the extent to which water, either added or released from mineral reactions, may affect the mechanical properties and the microstructure of these rocks. The experiments were conducted in a Griggs&apos; hot creep apparatus at temperatures and pressures up to 900ºC and 1000 MPa respectively; and most of them were performed in the constant strain rate mode [(1.10-6 < t < 1 • 10-4 s-1 )]. All three rocks were low porosity rocks, and the wet specimens never contained more than 0.9 wt % of added water. The experimental results are, however, quite unequivocal: They show that wet rocks are weaker than dry ones. A significant difference is even found for rocks tested in uniaxial compression at room temperature. A few experiments carried out on specimens obtained from larger prestressed rock cores indicated that the central parts of these cores were more likely to contain more microcracks than the ends. Optical microscope examinations revealed that extensive microcracking takes place even at the highest temperatures, where other mechanisms such as slip and dislocation creep also become important. Very little partial melting could be observed except for the specimens deformed at 900ºC.

Jan 1, 1982

By Juliana Gutiérrez-Paredes

Keywords: Slag, chromium oxide, recovery, stainless steel Experimental and theoretical work was performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1600°C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg). The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO)/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO)/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics) computational package is used to determine the equilibrium between the slag and molten steel.

Jan 1, 2005

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By J. E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to determine the influence of mining machine-mounted scrubbers on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery with a model mining machine that simulated airflow created by a dust scrubber. During the tests, ultrasonic anemometers were used to measure airflow speed and direction at several locations near the face. For the same test conditions, methane was released from the face and gas concentrations were measured at 21 locations above the machine using fixed point methanometers. Changes in airflow speed and direction are correlated with scrubber airflow and the measured methane distribution above the mining machine. The research results showed that operation of machine-mounted scrubbers improved face ventilation when blowing ventilation is used by increasing both the intake flow and the quantity of air reaching the face.

In the estimation of reserves the known values of the variables of interest from surrounding drill holes are used to compute or estimate the unknown value of the orebody over a given region or at a given point of interest. The classical means of doing this are: 1. The Polygonal Method û where the region is divided into polygons centred on bore holes, each variable is then assumed to have constant value over each polygon. 2. Inverse distance methods, where the variable is assumed to vary linearly with the distance between the known values of the drill holes. 3. Inverse distance squared method û a quadratic variation is assumed for the variables between the bore holes.

Jan 1, 1983

By Minoru Kawamura, Shinya Tanaka

In Japan, a cartridged emulsion explosive is generally used for tunneling. The workers are compelled to approach the face on charging the explosives into the drill hole with the tamping rod. Therefore, the workers are exposed to the risk of the disaster with the cave-in and the falling rock. The mechanization of the tunnel work has been advancing gradually. Especially, the development of the mechanization for charging work is desired in order to avoid the risk of disaster on workers. Recently, some charging machines such as the bulk emulsion explosives have been evaluated. However, a universal method has not been established yet, because the evaluated machines were not adequately suited from the point of the regulations and the consumption style of explosives.

Jan 1, 2008

By Vasile Pop, Ovidiu Galca, Constantin Salajan

The paper comprises a brief presentation of the rock fracturing techniques applied in CNMPN “REMIN” Company’s mines in Baia Mare. Parallel are emphasized some shortcomings of this field. The second part of the paper includes our preoccupations and achievements, of the last period, in especially those linked to techno-economical indices improvement resulting from the development of relatively large section mining works and blasting applied with sublevel caving methods.

Jan 1, 2003

By H. B. Arntzen, P. O. Grøntvedt, T. Lindstad, R. J. Ishak, M. Syvertsen

Better utilisation of electric power and coke is vital in reducing production costs and CO2-emissions in production of ferromanganese. All FeMn smelting operations consume 10 to 30 % more carbon than the carbon needed to reduce MnO and FeO to metal and the carbon contained in the alloy. Potassium which re-circulates and builds up in the furnace has been shown to be the main culprit causing both excessive carbon consumption, by catalysing the Boudouard reaction, and increased electric power consumption. The reaction between CO2 and ordinary metallurgical coke or coke impregnated with potassium has been studied at temperatures from 800 to 1100°C in a thermobalance apparatus. Ordinary coke did not react to any great extent at temperatures up to 1000°C, whereas the addition of potassium (2-10 %) resulted in a huge increase in reaction rates. The ultimate goal is to fit the results into a reaction rate model containing the equilibrium constant for the solid-gas heterogeneous reaction between CO2 and a free active site on the carbon reactant producing CO and adsorbed oxygen (an occupied site). The model includes the partial pressures of CO and CO2, a reaction rate constant that is a function of both the total number of reaction sites of carbon, and the potassium content. The potassium dependency is taken care of by introducing activity coefficients for the carbon sites. As the first step towards such a model, a regression line for the Boudouard reaction rate has been established.

Jan 1, 2004

By P J. Marsh, P J. Bartsch, N J. Semler

Iron Road Limited is currently studying the feasibility of producing 20 Mt/a of high-grade (67 per cent Fe) magnetite concentrate from a 2.6 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate has been tested at a relatively coarse grind size of -106 ¦m. The preliminary flow sheet has been confirmed based on initial mine plans and comprehensive metallurgical testing across the range of mineralisation. Extensive Davis tube testing to predict magnetite recoveries has been conducted over the resource, however this was completed at settings different to the optimised settings developed in the metallurgical test work program.This paper outlines the development of an ore treatment simulation in SysCAD which utilises the mine production plan, the Davis tube test data from the resource, data from metallurgical test work and process design criteria to predict magnetite concentrate deliveries. Mineralogical data, including QEMScan results and metallurgical assessments, were a fundamental basis of the process models which enable predictions of concentrate yield and quality. Power and water requirements are also calculated within the model. SysCAD dynamic simulation has been used to assist with the design of the process plant and downstream infrastructure. The simulation has been set-up to allow iterative integration and optimisation of the mine plan when it becomes available.CITATION:Semler, N J, Marsh, P J and Bartsch, P J, 2013. Iron RoadÆs prediction of magnetite concentrate production from the Central Eyre Iron Project, in Proceedings Iron Ore 2013 , pp 539-546 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By K. M. Li, Y. D. Zhang

The selection of stripping dragline is a complicated problem. Several factors, such as the deposit buried conditions, the demand of mine production rate, cast blasting result, the mining/stripping operation method and parameters, etc. may comprehensively influence the optimal selection of technical specifications of the dragline. Under these circumstances, the basic thinking and procedures for dragline selection are put forward as follows. •Step 1—Initially estimate the dragline annual stripping rate and stripping bench height according to the annual coal production rate and advancing speed of mining front. Then the feasible alternatives of dragline sizes can be calculated and selected from the existing dragline series. •Step 2—A computer simulation model is developed to simulate the dragline stripping operation, to obtain a series of working face parameters, then to select the best dragline alternative. This step can be interactively iterated until the satisfactory results are obtained. •Step 3— Sensitivity analysis can be done with the systems simulation model by changing the stripping bench parameters, e.g. stripping bench height and cut width, etc. to verify and modify the selection results if necessary. The mathematical model for dragline stripping simulation has been set up. The flowchart of the model is shown. A case study for a large surface coal mine with annual production rate of 16 Mt/a is followed. The dragline bucket capacity and operation radius, stripping bench height and cut width as well as other parameters are comprehensively optimized and selected. Keywords: Open cast, dragline, specification, selection, cast blasting

Jan 1, 2003

By K. -H. Lux, Z. Hou

ABSTRACT: It is well known in underground mining and waste disposal that the development of excavation damaged zones (EDZ), and thus, hydraulic pathways, is closely related to the excess in the corresponding damage boundary (= long-term strength) of the rock mass and the resulting damage. By integrating short-term and long-term strength, dilatancy, damage and healing into the newly extended Hou/Lux constitutive model for rock salt, it is possible to treat the tertiary creep, to identify the EDZ around underground facilities and to predict the time-dependent development of the EDZ in rock salt. Under in-situ conditions, the EDZ of a 37-year-old drift at the Sondershausen salt mine and the EDZ around a drift dam in rock salt are numerically examined. The numerical analysis gives satisfactory results. RÉSUMÉ: Dans les exploitations minières et le stockage souterrain des déchets, le développement des zones endommagées et fracturées (EDZ – excavation damaged zone), créant des chemins préférentiels pour écoulement, est étroitement lié au contexte géotechnique et à la méthode d’excavation. En intégrant la résistance court et long terme, la dilatance, l’endommagement et le colmatage, le nouveau modèle rhéologique Hou/Lux pour le sel gemme est capable de traiter le fluage tertiaire, d’évaluer l’extension de l’EDZ et de prédire l’évolution de EDZ dans temps autour des ouvrages creusés dans le sel gemme. L’EDZ d’une galerie datée de 37 ans dans la mine de sel de Sondershausen et les EDZ autour de barrage des galeries dans un sel gemme ont été modélisées. Les résultats numériques fournissent des résultats satisfaisants. ZUSAMENFASSUNG: Bekanntlich ist die Entstehung von Auflockerungszonen und damit hydraulischen Wegsamkeiten in der unmittelbaren Umgebung um bergmännische Hohlräume mit der Überschreitung der entsprechenden Schädigungsgrenze eng verbunden. Unter Berücksichtigung der Bruchfestigkeit, Schädigungsgrenze, Dilatanz, Schädigung und Verheilung kann das Stoffmodell Hou/Lux das Verhalten des tertiären Kriechens beschreiben, die Auflockerungszone im Salzgebirge ermitteln und ihre zeitabhängige Ausdehnung vorausberechnen. Mit diesem Stoffmodell werden die Auflockerungszonen einer 37jährigen Strecke in der Salzgrube Sondershausen und die Auflockerungszonen um ein exemplarisches Abdichtungsbauwerk im Salzgebirge numerisch untersucht. Dabei werden zufriedenstellende Berechnungsergebnisse erzielt.

Jan 1, 2003

By B D. Burford

High intensity stirred milling using the IsaMill has been the enabling technology for many projects by transforming the economics of fine grinding and simplifying circuit design. IsaMill grinding technology was originally developed for large-scale grinding to P80 sizings of 7 ¦m. The IsaMill is a high throughput, high efficiency mill that produces sharp product size distributions in open circuit configuration. The ability to grind in an inert environment, using a wide variety of media types, can give further metallurgical and economic benefits. The high energy intensity results in a small footprint that enhances the ability to distribute grinding power throughout the circuit, applying grinding energy to the minerals that need it. Recent scale up developments in IsaMill technology have enabled the benefits to be extended to large-scale conventional grind sizes, until now the domain of ball and tower mills. This paper will examine the crossover of IsaMill technology from ultrafine applications into the more conventional grinding area (P80 20 - 150 ¦m). Scale-up developments in IsaMill technology that have enabled this are reviewed. The upcoming commissioning of a 3.0 MW M10,000 IsaMill, the most powerful to date, grinding to P80 55 ¦m at PPL in South Africa will be discussed, as will the recent commissioning of a 2.6 MW M10,000 IsaMill at Kumtor. Recent testwork at McArthur River, where an IsaMill is being considered as an addition to the primary grinding circuit to replace the current tower mill will be reviewed. The potential combination of HPGR and IsaMill to transform concentrator grinding economics will also be discussed. Large-scale IsaMill technology has the ability to transform circuit design and energy efficiency for both coarse and fine grinding.

Jan 1, 2006

By Shailendra Chawla, Ashok Jaiswal, B. K. Shrivastva

The study aims to evaluate the pillar behavior during the depillaring operation by continuous miner (CM) technology. A panel with five headings developed as per the coal mine regulation of Indian coal mines [2] has been selected for the study. The depillaring operation has been carried out using CM technology after widening and heightening the original entries. An extensive field investigation has been carried out throughout the depillaring operation to access the mining conditions. Depillaring operation has been performed smoothly up to the middle of the panel (fourth row out of eight rows of four pillars each). Advanced blinking of the auto warning tell-tale (AWTT ) has also been observed on some of the instruments during the splitting of pillar no. 18. The panel shows extremely difficult mining conditions at this stage. The case has been numerically simulated using three-dimensional numerical techniques. The simulation result has indicated the high stress and yield condition on the working and the barrier pillar (surrounding goaf from both sides) after the extraction of pillar no. 18. The analysis has also indicated the marginal stability of the 2nd barrier pillar (namely “pillar B”). The failure of the barrier pillar could be the responsible for global instability of the panel as observed in the field. Understanding the importance of the barrier pillars, panel design has been modified by incorporating an additional row of barrier pillars. The stability of the modified panel has been evaluated. Both working and barrier pillars have been observed stable in the modified panel. This could be an alternative layout considering safety at the working face.

May 8, 2022

By William Hustrulid

Pre-split blasting is a primary technique for creating slopes with a minimum amount of unwanted damage to the remaining rock mass. Rock slopes created in such a way have both safety-related and economic advantages. The applications extend from road cuts to rock quarries to large open pit mines. For example, as deep open pit mines approach the end of their operating lives, slope steepening is one option to be considered. To be able to safely achieve and maintain steepened final slopes, good blast design techniques must be available and applied together with close operational control. Pre-split blasting is an important element in this slope creation process.

Jan 1, 2007

By Steven Townend

Mining-related activities have been known to create a challenging operating environment for mining companies located in close proximity to communities. Issues such as noise, vibrations from mining operations, land use and emissions are often a concern for community residents. In order to develop good community relationships it is necessary to take a proactive approach. This paper documents this approach and also deals with the social implications for Vale associated with mining activities in the heart of the community of Copper Cliff, Ontario, Canada.

May 1, 2011

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005