Search Documents

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By Robert Stefanko

This report abstracts project work performed for the USBM Grant No. GO-133077 during the period 19 June 1973 to 15 October 1974. Five reports have been separately produced and are as follows: 1. Mine Electrical Systems Evaluation - Cable Splicing, 2. Mine Electrical Systems Evaluation - Explosion-Proofing of Mine Containers, 3. Mine Electrical Systems Evaluation - Transient Analysis, 4. Mine Electrical Systems Evaluation - Mine Power System Performance, and 5. Mine Electrical Systems Evaluation - Model Coal Mine Electrical System Specifications. Abstracts of each comprise the balance of this executive summary, and 50 copies of each volume have been forwarded to the USBM under the terms of the grant agreement.

Jan 1, 1974

By D. Harrington

"Coal—mine explosions are accidents that can and should be prevented. In former years hundreds of lives were lost each year in the United States as a result of such explosions, but after 1932 the numerous precautionary measures adopted had reduced their frequency and severity 75 percent or more until in 1940 several very disastrous explosions marred the good record. Unfortunately, both the number and severity of explosions seem to be tending to increase compared with the relatively good achievement from 1933 to 1940. The requisites for an explosion are ever present in all soft-coal and many hard-coal mines. A certain combination of circumstances, such as a flame or an arc in a cloud of dust or in a body of gas or both may start an explosion at any time. The fact that the frequency and severity of explosions were lowered for 6 or 7 years is no guarantee that such freedom from explosions will continue, as the bad record of 1940 has shown, and underground workers should feel honor bound to exercise the utmost care so that they will not help to bring about the circumstances that will cause an explosion.Although mine operators bear the main responsibility for preventing explosions, miners can do many things to help. As about 9 out of 10 explosions begin at a working face, it is largely within the power of workers to prevent them. All miners should do their part willingly and should not defend a fellow workman from punishment, even from discharge, for disobeying necessary rules, whose disregard may cause the death not only of the safety-rule breaker but also of many of his coworkers.When a miner is careless and is injured some other way than by an explosion he may be the only one to suffer, but if his carelessness causes an explosion he not only endangers his own life but also that of every other man in the mine and possibly the lives of persons outside the mine.Experiments have shown that ignition of as small a quantity as 150 cubic feet of an explosive mixture of methane and air under certain circumstances can start an explosion that will traverse an entire mine. Thus, ignition of an explosive mixture of gas 1 foot down from the roof and 13 feet back from the face of a 12-foot entry might cause a widespread explosion if the right quantity and kind of dust were present. Many persons have ignited much larger quantities of gas without being killed, but they survived only because dust, confinement, and other conditions were not exactly ""right."""

Nov 1, 1940

By G. T. Lineberry, W. J. Wiehagen

A Paradigm Shift As market economists, mine managers are interested in "staying in business" and even "prospering." Bottom-line results are the "order of the day." Concern for bottom-line results invokes questions such as: How much was produced? At what cost? And, was anyone injured? While these questions will always carry everyday emphasis at the mine, they are fundamentally lacking in that they often appear, especially to lower levels of management and to the production worker, as preeminent concerns. Driven by market economics, many organizations have decentralized, outsourced, downsized, restructured, and formed new coalitions. Investments in new technology and concentration on productivity have been part and parcel with these changes, contributing to improvements in both safety and efficiency. A reason for (and, perhaps a result of) these improvements has been the development of a highly experienced and flexible work force. These changes in mining present an interesting opportunity to modify a few paradigms about work life in general, and perhaps a few paradigms about how we invest in the miner, in particular. Studying these issues now might offer some interesting opportunities for the future, as the foundations for the next generation of mine workers are laid. With the average "experienced" U.S. miner five to fifteen years from retirement, perhaps a key determinant of future success in the world market might be how well we make the transition from today's work force to the work force of tomorrow. We can ill afford to wait a few more years to tap into the special knowledge residing within a veteran mining work force. The WCPM work Crew Performance Model, see pp. ) is one approach to defining, capturing, and transferring this expertise.

By F. Castelli

A simplified non-linear method to predict the behaviour of a single pile and/or pile group under horizontal loads is presented in the paper. The evaluation of the non-linear lateral deflection is based on a procedure taking into account the decrease of the model stiffness with the increasing of the applied load. The solution derived firstly for the single pile, was extended to the case of a pile group introducing the p-multiplier (fm) concept proposed by Brown et al. (1988).

Jan 1, 2006

By Ali Kahriman, Alper Celtikc, Serdar Celik, Tuncer Gungor

This paper presents the results of ground vibration measurements carried out in Gülyali Hisarcik Basalt open pit mine located on the north side of the Anatolia near Ordu province in Turkey. Within the scope of this study in order to predict peak particle velocity level for this site, ground vibration components were measured for 5 shots during bench blasting. In blasting operations; ANFO (blasting agent), gelatin dynamite (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 5 different vibration monitors (4 White Mini-Seis and 1 Instantel Minimate Plus Models). The absolute distances between shot points and monitor stations were determined using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity.

Jan 1, 2013

By Dennis R. Kasper

This study evaluates selective environmental impacts of two distinct in situ mining techniques. In situ leaching of uranium, porphyry copper and native copper and in situ borehole (slurry) mining of uranium, sandstone, and pebble phosphate ores are the techniques and minerals investigated. The potential impacts onsite in the desert southwest (porphyry copper), Michigan (native copper), Texas and Wyoming (uranium), and Florida and North Carolina (phosphate) are addressed and discussed. The study emphasizes those impacts which are unique to in situ solution leaching and borehole slurry mining. Impacts which are characteristic of all construction projects in the general geographical areas investigated, such as socioeconomic effects on surrounding communities and site-specific impacts, such as rare and endangered species, are beyond the scope of this study. For each of the in situ processes and associated ores investigated, the physical and chemical characteristics of the systems are described, the toxicity of the leaching solutions are presented, and the potential impacts on the environment are developed.

Jan 1, 1979

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By Elizabeth Gardiner

Tailings and water management facilities are integral components of mine and mill operations. They must be managed for the long term to ensure that safe and environmentally responsible stewardship is achieved. The Mining Association of Canada (MAC) has developed and published two manuals to provide guidance to mining companies on sound practices for the safe and environmentally responsible management of tailings facilities: ???A Guide to the Management of Tailings Facilities; and ???Developing an Operation, Maintenance and Surveillance Manual for Tailings and Water Management Facilities. The Guides were designed to help companies develop and implement tailings management systems that include environmental and safety criteria, to improve the consistency of application of sound engineering and management principles to tailings and water management facilities through their full life cycle, and to demonstrate this to regulators and the public.

May 1, 2003

By D. R. Dolinar

The fall of small pieces of rock between roof bolts causes over 80 pct of the ground fall injuries in underground coal mines. Roof screen, if installed on the bolting cycle, can significantly reduce the number of these injuries. As the surface of the roof fails, the screen will have to retain the broken rock without failing or excessive deformation. Welded wire screen is the most common type of screen material used for roof surface control in underground coal mines. The load-deformation characteristics and the load capacity of welded wire screen were evaluated in the laboratory in a specially built test frame. In the frame, the square screen sections were held in place by bolts and bearing plates at the four corners while a center load was applied to the screen. The parameters evaluated included the wire gauge and configuration, the bearing plate loads and bolt spacing. The wire gauge of the tested screen was 4, 6, 8, 9 and 10. Maximum screen capacities for both load and displacement were developed for each of the wire gauge sizes along with the screen stiffness. This information can be used for screen selection and for the evaluation and determination of screen performance. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By A Weber, L MacNamara, H Schreiber

Design and development of the world?s largest flotation cell was completed in 2002. This was the first 257 m3 flotation cell installed in the mineral industry and represents a major development in the design of larger flotation cells. This cell has a 50% increase in volume over the widely installed 160 m3 WEMCO® Smartcell? flotation machine. In the next few years it is anticipated that 257 m3 flotation cells will be incorporated into rougher-scavenger flotation circuits in many more world class copper sulphide concentrators. The prototype 257 m3 cell, No.250 Smartcell? flotation machine was installed at Minera Los Pelambres in the front of Row 1 in the existing rougher flotation circuit. This cell is followed by nine No. 130 Smartcell? flotation cells. After the successful development phase, this unit has been incorporated as part of a row of No. 250 Smartcell? flotation machines at Minera Los Pelambres. A key to the successful development of the equipment has been the emphasis placed on fundamental hydrodynamic scale-up criteria. Hydrodynamic factors include superficial gas velocity, water (pulp) circulation through the draft tube, and pulp mixing (distribution) characteristics. This paper will review the scale-up criteria of the No. 250 flotation cell, and present a case study of the in-plant equipment testing. The case study will document the metallurgical and hydrodynamic performance of the machine. It will also illustrate the economic benefits derived by incorporating larger flotation cells in a modern copper sulphide concentrator.

Jan 1, 2007

By Stephen C. Tadolini, Thomas M. Barczak, Paul McKelvey

A new generation of hydraulic mine support prestressing devices has been developed. These thin-walled steel shells are machine-welded and can be inflated with water or any liquid to provide prestressing for a wide variety of roof support products ranging from Can supports to props and cable bolts. With an expansion capability of several inches, depending on the geometry and size of the unit, they can also establish roof contact eliminating the need for wooden wedges or crib blocks that are commonly employed with several standing roof support products. Capable of withstanding pressures from 1,000 to 6,000 psi, these cells are able to transfer roof loading into the support structure without rupturing. A recent development has been the addition of an inexpensive yield valve that provides control of the maximum pressure and load development on the support. This paper examines the performance capabilities of these inflatable prestressing units and the impact they have on the performance of various support systems, including an evaluation of the overall stiffness of the support system and the load control during yielding of the prestressing unit. Recommendations are made regarding the design requirements of the prestressing unit to optimize the support performance. A summary of mine applications using this technology is provided with general comments regarding their impact on ground control.

By Colin P. Pigott

The paper describes a variety of existing techniques and equipment which when combined together permit faster and cheaper drilling of shafts in soft to medium strength formations. Drilling fluid circulation, methods of hole stabilisation and bit design, including the advantages of flat bottomed and conical bits, shrouds and skirts, tungsten carbide, long tooth and disc cutters are considered. The principles of rock chip transportation and bottom hole cleaning are described together with a new and very efficient fluid circulation system which was invented by the author.

Jan 1, 1985

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

By S. J. Frank

The development of feedforward semi-empirical control models for furnaces and the evaluation of mass balances are based on plant data. The models can only be as good as the data and it is therefore required to know the inherent uncertainty associated with the plant data. This uncertainty stems mainly from the fact that the slag, alloy or dust, have a distributed nature that depends on the degree of mixedness. It is commonly accepted that melts from open bath furnaces are well-mixed, and submerged arc furnaces less so. The impact of this assumption is significant, as a reasonably homogeneous melt could be represented by one sample only. As so much of metallurgical control depends on the assay information of the alloy and slag melts from furnaces, it was decided to characterise the possible variation in melt chemistry and temperature. Sampling campaigns and continuous temperature measurement of the melts were performed for different alloy and slag taps at a major ferrochrome producer. Both a submerged arc furnace and open arc furnace are evaluated in this way, by way of comparison. The slags of both open arc and submerged arc furnaces were found to be of similar degrees of homogeneity, with much spatial variance in the reducible iron and chromium oxides. However, it was found that the alloy melts deriving from open arc furnaces were significantly less homogeneous than the alloy derived from submerged arc furnace alloy production. The compositional variance could be related to the furnace operating conditions and it affects both metallurgical accounting and process control. In all cases it was found that the variance in melt solute components are larger than can be ascribed to analysis instrument error. It will be shown how this predetermined variance in melt composition could be included in process modelling and control.

Jan 1, 2004

By Rossiter W. Raymond

(Canal Zone Meeting, November, 1910.) THE death of Professor Blake removes the oldest of American economic geologists and mining engineers, and deprives this Institute of one of its, earliest and most illustrious members. To many of us it brings a personal loss also, the loss of a friend. William Phipps Blake was born June 21, 1826, in New York City. -His father, Elihu Blake, was a surgeon-dentist of eminence, a direct descendant of William Blake, who settled in the Massachusetts Bay Colony about 1630. He was prepared for college at private schools in New York, and entered the Sheffield School of Yale, where he was graduated as Ph.B. in the chemical course, class of 1852, the first graduating-class of the institution. In the same year he became chemist and mineralogist of the New Jersey Zinc Co., and chemist of chemical works at Baltimore, Md. In 1853, lie started the Department of Mineralogy of the World's Fair at New York City. In 1854, 1855 and 1856, he was mineralogist and geologist of the United States Pacific Railroad Surveys of Williamson, Pope, and Whipple, and for the War Department at Washington. His writings, during this period comprise reports on the geology and mineralogy of California and other parts of the Southwest, and constitute well nigh the earliest scientific accounts of the regions described. One of them. was a translation of the Resume and Field Notes of Jules Marcou, of Whipple's expedition. From 1856 to 1859, he was engaged in explorations of the geology and mineral deposits of North Carolina, :and other parts of the country. In 1859, he became editor and proprietor of The Mining Magazine. This was a monthly periodical, founded in 1853 by W. J. Tenny, who conducted it until 1858, when it passed into the hands of Thomas McElrath, a New York publisher, and appeared in May of that year as The Mining and Statistic Magazine, with the name of

Sep 1, 1910

By F. W. Gray

IN 1922, the writer communicated to the Institute a paper entitled The Development of the Coal Industry in Canada (1), which summarized the considerations set out in a series of papers (2) concerned with coal-mining in Canada which he had presented in 1920 and 1921. This paper contained a forecast by decades, commencing 1920, of Canadian coal production, importation, consumption, and exports, based on anticipated rate of population increase, and continuation of the gradual increase in the per capita rate of coal consumption in Canada that had taken place every year up to 1920. The following comparative statement brings our the differences between the forecast and actual experience:

Jan 1, 1936

By H. Akbari

The ordinary Portland cement (OPC) is the key pozzalonic component of the concrete mix, widely used as the construction material world-wide. Billions of tons of OPC are used in the construction industry each year. However, calcinations of limestone and silica that produce OPC also produce almost an equal amount of CO2 during the cement manufacturing process. Thus, OPC production accounts for nearly 7% of all anthropogenic CO2 emission each year. The main objective of this study was to develop a geopolymer-based composite to be used as a substitute for OPC in concrete application to significantly lower the carbon foot print of the construction industry. A waste material produced during the coal combustion process was used as the main raw material for the geopolymer-based composite. It was mostly the non-metallic content of the F-type fly ash produced from the combustion of bituminous coal. The authors envisioned to extract some of the valuable metal oxides from fly ash prior to using the major non-metallic portion of the fly ash for geopolymer concrete application. The results obtained from this study exhibited that the compressive strength of the geopolymer concrete compares favorably with that of the conventional concrete prepared using the OPC.

Feb 27, 2013