Search Documents

By Ke Yang

Drilled shafts are widely used as foundation system for sound walls to resist lateral loads. The design method based on the ultimate lateral capacity, such as Broms method, is often used for sound wall foundation design. Allowable Stress Design (ASD) is currently used for deep foundation design. However, by October 2007, all states Department of Transportations are required to use the Load Resistance Factor Design (LRFD) approach for the design of foundation in highway projects. There is a need to develop a calibrated resistance factor in LRFD lateral design of drilled shafts supporting sound barrier walls. This paper provides resistance factors for design of laterally loaded drilled shafts supporting sound walls using Broms method based on the study using reliability based method and fitting to ASD method. Additionally, the resistance factors for static lateral load tests are recommended. Furthermore, a methodology to update the resistance factors using Bayesian approach by incorporating the on-site full-scale lateral load test results is presented. To illustrate the Bayesian update methodology, two lateral load tests in Colorado were employed to develop the updated resistance factors.

Jan 1, 2007

Blasthole deviation is a frequent, well documented and undesirable occurrence in mining operations. It is caused by the drill string mechanics, operating variables and the interaction between the drill bit and the rock mass characteristics. It is composed of three distinct components: collaring or marking error, alignment error and trajectory deviation. This study has focussed on the dependence of trajectory or natural deviation on the geological features of the rock mass being drilled.

Jan 1, 1996

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By W. G. Pariseau

This contribution focuses on the role of stress analysis for mine planning and the selection of suitable computer programs for the task with special emphasis on coal mine pillars. In this regard, barrier pillars that defend a set of five main entries at the Crandall Canyon coal mine in central Utah were formed during extensive longwall mining north and south of these main entries. Numerical analysis for ground control guided the mine planning and permitting. Retreat mining of pillars led to disastrous events August 6 and 16, 2007, with the loss of nine lives. A most difficult lesson taught by the Crandall Canyon tragedy is the need for education in the selection and use of computer programs for pillar design. Much of this contribution is taken from a report prepared for the Mine Safety and Health Administration (Gates, et al, 2008). Details appear in Appendix Q of the report (Pariseau, 2008). The Crandall Canyon mine is about 16 miles west of Huntington, Utah, in the Wasatch Plateau coal field. Geology of the Wasatch Plateau is described by Doelling (1972) as gently dipping Cretaceous sandstones, mudstones, coal seams, and shales. Joint systems are present in strata above and below coal seams where cleat systems are present as described by Hucka (1991). Several major fault systems transect the field and form grabens with 450- 760 m of drop. One such structure is Joes Valley fault that crosses the Crandall Canyon mine. Mines in the Wasatch Plateau are generally developed from outcrops in steep canyon walls. Overburden increases rapidly as mining progresses into the plateau; mining depth varies with topography between 450 and 600 m in the region of interest. A stratigraphic column derived from a borehole into the mine is shown in Figure 1. There are 11 layers in the column.

Jan 1, 2011

By S. Paul Singh

Rock is a heterogeneous medium, a fact often ignored during blast design. In reality, the rock mass characteristics have a controlling influence on the outcome of a blast. If the optimum blasting results are to be achieved over a range of rock mass conditions, it is prudent to understand the role played by the geological features of a rock mass in producing overbreak around the periphery of an excavation. The field work was performed in a drift located in a geologically dominant rock mass and also included observations and assessment of blast damage at several operating mines. The blast damage was estimated on the basis of the half cast factor. The effect of rock strength, rock quality designation, orientation , frequency and aperture of joints, number and thickness of layers and hydrogeological conditions on blast damage has been described.

Jan 1, 2000

By D. G. Klaren

Self-cleaning fluidized bed heat exchangers are conquering the world for reason that they are able to solve any severe fouling problem in indirect heat transfer due to the circulation of cleaning particles through the tubes of vertical shell and tube exchangers. In most cases, these particles consist of chopped metal wire. Moreover, self-cleaning fluidized bed heat exchangers perform with excellent heat transfer at very low liquid velocities, which makes completely new designs of shell and tube configurations possible. Further, self-cleaning fluidized bed heat exchangers show a strong shear thinning effect in non-Newtonian liquids. All the above characteristics make the self-cleaning fluidized bed heat exchanger an ideal tool for the indirect heating of laterite nickel slurry in High-Pressure-Acid-Leach (HPAL) plants. Preliminary tests and evaluations of these heat exchangers have shown that the performance and price of these heat exchangers used for the production of nickel and cobalt from a laterite slurry, cannot be matched by existing conventional heat exchange systems. This article explains the principle, design, lay-out and enormous advantages of the self-cleaning fluidized bed heat exchange technology in a plant suitable for an annual production of approx. 45,000 ton nickel and 4,500 ton cobalt from laterite slurry through high pressure'acid leaching.

Jan 1, 2002

By Forrest T. Moyer

The safety record of the coal-mining industry, both anthracite and bituminous, in 1966 was improved over that of 1965 in all general measures of injury experience. The improvement was more pronounced in the anthracite industry. The total of 10,679 disabling work injuries comprised 233 fatal and 10,466 nonfatal injuries, 26 and 692 fewer, respectively, than in 1965. The number of fatalities in 1966 was the lowest annual total since complete records were started in 1910. Similarly, the number of nonfatal injuries in 1966 was lower than in any year since 1930 when such data were first collected.

Jan 1, 1969

By C. Laughton

The Deep Underground Science and Engineering Laboratory (DUSEL) is to be constructed at the defunct Homestake Mine, in South Dakota. As a cornerstone of DUSEL?s research program, it is intended to conduct experiments into the fundamental nature of neutrino and proton particles. The experimental apparatus required to con-duct these experiments will be housed in large rock cavern(s) sited at depths of over a kilometer. As conceived, these cavern(s) are planned to have mined volumes of up to half a million cubic meters, and spans of approximately 50 meters. The paper will describe key end-user requirements, and outline the in situ rock conditions and mine site constraints that are likely to play determinant roles in identifying candidate sites and developing cost-effective design options(s).

By L.L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By L. L. Wyman

The exact nature of the changes that take place in the iron-nickel alloys, giving rise to the interesting and useful expansion alloys in the Invar range, has yet to be fully understood. Similarly, the ternary iron-nickel-cobalt alloys, which also possess such commercially useful expansion characteristics,1,2 are concerned with transformations that appear to be identical with those found in the parent iron-nickel alloys. The investigations on iron-nickel alloys in the range 26 to 29 per cent Ni have been reported by several authors3-9 wherein it is shown that there are factors other than temperature, such as stress and grain size, which play an important part in determining the temperature at which the low-temperature transformation takes place. It will be shown in this paper that the ternary iron-nickcl-cobalt alloys having nickel contents comparable to the alloys mentioned above behave in a parallel manner. The alloys in the range of 26 to 31 per cent Ni and 16 to 21 per cent Co have a coefficient of expansion of about 4.0 X 10-6 per degree Centigrade, and the alloys in this range of composition find considerable application in making glass-to-metal seals, because these expansion properties so well match commercial glasses. The behavior of these alloys is not a simple matter, for it has been observed in alloys of 28.5 per cent Ni and 18.5 Co that severe working ran cause the appearance of a second phase having a needlelike structure similar to the martensite structure in carhon steels. Fig. 1 shows the change brought about in an alloy of this composition when a strip of this material was cut with tin shears. This second phase has been identified as the body-centered cubic alpha phase, and it is the purpose of this paper to describe the results of some of the preliminary investigations in the study of the changes involved in these alloys. Materials The past work on these alloys has concerned itself primarily with materials made by the usual casting procedure and involving the use

Jan 1, 1939

By J Steyn

Block Cave mining is one method used to extract ore from underground diamond mines as well as other massive orebodies such as copper. This necessitates the excavation of many kilometers of tunnel within the ore body. The integrity of these excavations needs to be maintained over a number of years. Most Kimberlites and weak orebodies are extremely susceptible to degradation when exposed to moisture and the atmosphere. It is therefore essential that some form of weathering protection is applied as soon as possible after exposure. Conventional methods of weathering protection such as shotcrete do not easily fit in with the production schedule, hence the need for a more efficient system that could be applied immediately after exposure and serve as a temporary support or even as a permanent support medium. The main advantages of thin sprayed liners (TSL) compared to shotcrete are the ease of application, speed of application, early strength, much reduced transportation of material, less labour intensive and cost effectiveness. Several Thin Sprayed Liners suitable for various mining environments and geotechnical conditions are available and could be well suited as additional support the undercut level development in a block cave where this may be required. TSL offer a cost effective support solution as an alternative to shotcrete in areas where the building of a support structure is not a requirement.

Jan 1, 2008

By Douglas A. Anderson

The simplest method used to predict ground vibration from blasting is scaled distance -the distance from a blast divided by the square root of the Pounds per delay. Pounds per delay is defined as the number of pounds of explosive detonated within an 8 millisecond (ms) interval. Based upon this definition, regression plots of peak particle velocity vs. scaled distance have been used to determine likely values of peak particle velocity.

Jan 1, 1989

By Jack A. McQuiston, Thomas A. Cross

Corrosion of equipment and machinery in the coal industry is usually the result of three main agents: acids, chlorides, and abrasion. Acids and chlorides are especially troublesome in coal preparation plants where soluble salts and sulfur in the coal produce a highly corrosive wash solution. Abrasion is common in all operations where coal is handled or conveyed. Together, the acid-chloride-abrasion combination results in some of the worst corrosive conditions found in any industry. The variety of equipment and structures in the coal industry calls for different corrosion control techniques. Table 1 lists the areas of concern for a number of items. Just as there is a wide variety of corrosion problems, there is a wide array of coating materials available. Tables 2 and 3 are selection charts to provide guidance in narrowing down the choices. Experience has shown that a limited number of coating systems work best on coal equipment and structures. These systems are described in Table 4. The good-better-best designation in the table refers to coating system longevity. Good indicates the least costly and shortest service life. In nearly all cases the lowest annualized cost can be achieved by using the coating system rated best, due to the avoidance of costly repaints and unnecessary downtime. The most expensive coating system, though, is worthless unless the coating system is properly applied. Field inspection to insure compliance with specifications is an important aspect, and is a service available from many coating suppliers. Even the best coating systems require periodic maintenance to achieve satisfactory results. Spot rusting from mechanical damage should be repaired annually to maximize the coatingsystem's results.

Jan 2, 1980

By Francisco Camus

El proceso de exploración en las campañas mineras es la primera fase del negocio y constituye una de los principales herramientas para su supervivencia, desarrollo y valorización de la industria. En este sentido, el presente texto señala la experiencia de Codelco en la exploración en Chile y su aplicación en Perú. Así, el conocimiento obtenido por Codelco realizado en el norte y centro de Chile, ha generado la formulación de modelos de exploración predictiva durantes los últimos diez años. Dichos modelos incorporaron el conocimiento logrado en el nivel de cada yacimiento individual, los entornos distritales y las franjas metalogénicas donde estos ocurren. En consecuencia, esta experiencia obtenida por Codelco y el reconocimiento de la continuidad en Chile, se extiende en el Perú y se presenta como una oportunidad de interés para el desarrollo de programas de exploración a futuro.

Sep 13, 2001

By S. Norman Kesten

The Galena mine is located astride the Polaris fault in the Coeur d'Alene district of northern Idaho. The surface installations are about a mile up Lake Gulch, the mouth of which is about 2.4 km (1 112 miles) west of the old town of Wallace. The mine had its beginnings when the first claims were located in the early boom days of the district in the 1880s and when the first underground ore bodies were opened up in 1917. During the ensuing 14 years, ore was mined from which were recovered 5.4 Mkg (12 million lb) of lead and almost 14.2 Mg (112 million oz) of silver. Workings consisted principally of a vertical shaft from surface to the 800 level and an offset underground shaft to the 1600 level, together with extensive lateral openings. High-grade silver-copper ore was discovered near the Silver Standard fault in the Sunshine mine, a few miles to the west, on the 1700 level in 1930. By 1937, the Sunshine and adjacent mines were producing silver-copper ore on a regular basis. In 1943 additional ore of a similar type was found along the Chester fault, to the east of the principal Sunshine workings. The interest of American Smelting and Refining Co. (renamed ASARCO in 1975) was aroused and the company's geologists determined that the Galena mine, idle since 1931, provided a geological environment in which similar ore might be found. After negotiations were initiated with the owners of the property, Callahan Zinc-Lead Co., the property in question was deeded to Callahan's wholly owned subsidiary, Vulcan Silver-Lead.

Jan 1, 1990

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

By Pravin Kumar

Goldcorp Inc.?s Red Lake Mine (RLM) is situated in the Red Lake Mining District, a history rich North Western Ontario mining community. Red Lake Mine formerly known as the Dickenson Mine has experienced various degree and type of bursting since the 1960?s. During the 1960?s burst were common in shrinkage stope box hole pillars. After discovering the High Grade Zone (HGZ) between its 30th and 39th levels, the mine has changed its mining method to mechanized cut and fill with cemented paste fill. The rock mass at RLM is mainly massive basalt-ultramafic and behaves in a manner consistent with massive brittle rock. This paper presents the use of empirical and numerical design techniques. The use of the Span versus RMR graph to determine critical stope spans at RLM and the use of numerical design techniques to determine the stability of the sills and post pillars. Selecting of a sill pillar dimension is illustrated using four different failure criteria?s. The four failure criteria are m & s failure criteria, the Pillar Stability Graph, deviatoric stress ???-?3), and induced stress level criteria ?1 /UCS, which are calibrated to RLM?s ground conditions. A wide range of case histories has been studied ranging from stable to highly burst prone ground conditions in order to calibrate the failure criteria to observed conditions and quantified to local micro seismic system.

May 1, 2002

By C. K. Leith

GENERAL GEOLOGY OF THE LAKE SUPERIOR IRON-BEARING AND COPPER-BEARING SERIES. THE geology of the Lake Superior region is of general interest, both from an economic and a scientific standpoint. The presence of large and rich iron- and copper-deposits has made a knowledge of the geology of the region necessary for purposes of exploitation and exploration. The ores of the region are contained in rocks of pre-Cambrian age, 'pith for most of the country up to recent years have usually been referred to as « crystalline schists " or " crystalline complex;" and regarded principally as metamorphosed basement-unit upon which the sedimentary rocks, beginning with the Paleozoic, were laid down. In the Lake Superior re¬gion this pre-Cambrian complex presents an unusual variety of rocks with determinable relations. It has been possible, with the large expenditures which-the magnitude of the iron-mining industry warrants, to work out their stratigraphy to a larger extent than has been possible in almost any other area of pre-Cambrian rocks. The real complexity of Lake Superior geology, the confusion of names and the multiplicity of reports covering small parts of the region, are such that interested persons, other than. geologists directly engaged in the work, may well hesitate to attempt to comprehend the geology of the region as a whole. The following paper is a somewhat elementary outline of the geology of the Lake Superior region with special reference to new developments not yet covered in published reports. Geological information concerning the region has been gath¬ered by mining companies, and by the geological surveys of Michigan, Wisconsin, Minnesota, Ontario, Canada, and the United States.. Perhaps in no other part of the country have the mining men themselves spent such large sums in purely geological work. This has made possible the publication of ,reports and maps by the State and Government surveys in much less time and at far less cost than would have been otherwise possible. The. U. S. Geological Survey is the only organization which has covered all of the region on the United 'States side of the boundary, and as its reports include the in¬formation gathered by the mining companies and State organi

Mar 1, 1905

By Syd S. Peng

Coal mine ground control is the science of the application of rock mechanics principles to coal mining operations. More acceptance of ground control techniques by the US coal mining industry has been seen in the 1980s. It has been demonstrated many times that a proper ground control design is key to a successful coal mining operation. However, numerous in-mine applications of various ground control techniques by the author indicate that cur¬rent techniques need improvement. The biggest problem in coal mine ground control is that miners are dealing with materials of rapidly varying properties and occurrence. And only the exposed surface can be identified positively. Thus, in attempting to solve the ground control problems, many unknown factors are assumed. Some of these problems deriving from such assumptions are discussed here. Coal pillars There are two types of coal pillars - barrier and chain pillars - depending on the purpose. Barrier pillars are those located between panels or sections or mines. Their objective is to isolate the mined-out effects of one from the other. Chain pillars are characteristic of room-and-pillar mining. They are designed to support the overburden load and protect the surrounding entries and crosscuts. Pillar design is the most popular and, frequently, the only ground control technique employed by coal operators for mine design. There are many pillar design formulae available (Bieniawski, 1983; Peng, 1986). Nearly all consider both size and width/height effects. Specifically, pillar strength decreases with increases in pillar size and increases with increase in the ratio of width to height. However, the manner of those changes varies with investigators. Consequently, the pillar size determined varies considerably from investigator to investigator. And the variation grows much more pronounced as the seam depth increases (Fig. 1). The question, then, is which one should be used? One may say each formula is developed for a particular coalfield. A particular formula may have been used to design a pillar, which has not failed. Does that mean it was over designed? Not necessarily, because no one can confirm its stated "safety factor." Recent case studies (Peng, 1986; Tang and Peng, 1988) show that all pillar formulae are too conservative for chain pillar design in room-and-pillar mines due to the following two problems: • Uncertainty about in situ pillar strength. All formulae employ uniaxial compressive strength of selected samples tested in the laboratory and scaled to that for underground pillars. The scaling factors are not well proven. In situ testings by Bieniawski (1969) suggested that 1.5 m (5 ft) pillars are representative of in situ pillars that, after being tested in various US coal mines, are not universally applicable. • Uncertainty about the actual loading on the pillar. The most frequently used tributary loading theory defines the loading as total overburden weight tributary to each pillar (from roofline to surface). This is too conservative when it applies to coal measure rocks. The overburden consists of layered strata of different stiffness. Many stiffer strata will self-support over small roof spans. Depending on the location of these strata above the coal seam, it will reduce pillar loading in various proportions. It follows that total structural analysis using, for instance, finite element method is more appropriate. It can take into account the interaction of roof and floor strata with coal. This has been demonstrated by Peng et al. (1986,1988) on several case studies. However, the validity of the finite element structural analysis depends on the accuracy of in

Jan 1, 1989

By Gary R. Gavan

This report presents the results of a research project that gathered detailed information on the composition of the population of mobile equipment used in U.S. coal mines. A computerized data bank containing over 19,000 pieces of coal mine equipment in use in 1976 was prepared with a data retrieval program. Operator protective structure technology is reviewed; field problems experienced with ROPS are discussed.

Jan 1, 1978