Search Documents

By Panshi Xie, Xicai Gao, Yi Luo, Youfu Zeng, Yongping Wu, Shenghu Luo

This research investigates roof deformation and failure characteristics, as well as mechanical interaction between the panels of the roof strata above two adjacent working faces in a steeply inclined coal seam. Physical modeling with photogrammetry measurement method has been employed in this investigation. The movement of roof strata and section pillar, as well as the stratum morphological characteristics, was quantitatively analyzed. Results show that the roof movement direction above the two panels has zoning characteristics, especially in the lower panel. Roof migration in the lower panel of the working face is larger than that in the upper panel. The roof to floor closure perpendicular to the seam direction is larger than the sliding along the seam. The maximum roof concave and convex bending occurred at the middle and upper parts of both panels; the roof bending in the upper panel mining area indicates a larger mining disturbance induced by lower panel mining. The void ratio contour of the lower panel is an asymmetrically arched shape, which is different from that of the upper panel area. The higher roof strata above the upper panel exhibit separation and breaking, whereas the lower roof exhibits compression due to mining in lower panel. The section pillar is compressed and slides slightly, which aggravates the mechanical interaction between the panels and increases the caving height of the roof over the lower panel and the periodic weighting intensity

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

By L. R. Plitt, A. A. Turak, B. C. Flintoff

"Since the publication of empirical cyclone models by Lynch and Rao in 1975 and by Plitt in 1976, the technical literature on this subject has consisted primarily of reports of applications, with only a few articles discussing basic modifications or enhancements in model form. In fact, most of the modelling eff ort in this period has been concerned with theoretical models based on the hydrodynamics of multiphase flow. (Preliminary resutls have been encouraging, however, it will be some time before this approach reaches the practical application stage.) This paper presents a review of empirical cyclone modelling technology, with an emphasis on developments since the mid 1970s. The topics addressed include homogeneous and heterogeneous ores, parameter estimation techniques, parameter confidence intervals, and the introduction of a new conceptual model of cyclone operation.IntroductionSince their first reported application in the mineral industry by Driessen (1939), cyclones have become a common unit operation in all of the process industries. The widespread use of the cyclone stems from its relative low cost and its versatility. It can be employed to carry out liquid-liquid, solid-liquid and solid-solid separations. It is the area of solid-solid separation which is of greatest interest to a mineral processing engineer. Historically, this area was divided into two application categories: (I) Separation according to density, the cyclone washer, and, (2) Classification according to particle size, the cyclone ciassifier. (When water is the carrier fluid, the cyclone is more often called the hydrocyclone. For the purposes of this paper the two names are used interchangeably). Classification is the principal application in mineral processing circuit s. Within this category, the cyclone is most commonly employed to provide some positive control over the size distribution of product from a grinding circuit. Other uses include sand-slime separation prior to froth flotation and mill tailings treatment, either for dam construction or in backfill preparation."

Jan 1, 1987

By L. E. Mordberg, E. N. Nesterova

Geochemical studies of the bauxite deposits show that the primary composition is gibbsitic. Some trace elements were relatively mobile during bauxite formation with the content of Th, U and Zr increasing and that of Rb, Ni and Co decreasing. Y and Pb were relatively immobile during lateritisation; their contents and ratios were inherited from different types of underlying rocks. The supply of Ni and Co took place at the diagenetic or epigenetic stages; their ultimate source was the crystalline basement in the region. The studies support the view that the bauxite was likely to have originated as a result of in-situ lateritisation and not through sedimentary transport and redeposition

Jun 18, 1905

Automation in underground mining enhances safety and leads to economic efficiency. In the past many efforts have been made on the automation of longwall shearer operation. With respect to the ultimate goal of automation, ie self controlled operation, coal bed boundary detection is one of the key problems. For longwall human labor is necessary in order to detect the exact position of the coal seam to be excavated. The authors present a sensor concept based on infrared technology and pattern recognition which will solve this problem. The very harsh underground conditions set high demands on the implemented sensors. The combination of infrared sensors and powerful processing algorithms is part of the innovative concept for automation of the new Eickhoff Bergbautechnik GmbH SL 750 shearer loader. The multi-sensor automation system EiControlPlus which is designed for the complete detection of the machine environment fills in the gap in the coal-excavation automation by building a recognition system that turns the shearer loader into an 'intelligent machine' which is capable of detecting the correct position of the seam to be excavated and thus enables human-free coal mining.

Dec 6, 2010

By Lance A. Roberts

Micropiles are commonly utilized for applications other than foundation retrofit. In bridges, for example, micropiles can serve as the permanent foundation elements or can be used in temporary support applications. In this paper, a case study on the use of micropiles for the 18th Street Expressway Bridge rehabilitation/repair project in Kansas City, Kansas is presented. In the project, micropiles were utilized for support of six temporary jacking structures, which allowed the bridge to be lifted while repairs were completed. A group of six micropiles was required to support each jacking structure. The required compressive service load per micropile was approximately 300 kips (1300 kN) and the settlement of the micropiles under the service load was to be limited to 0.5 in. (12.7 mm). Two field compression tests were conducted as part of the project. The field load test data was integrated within a soil-structure interaction capacity approach in order to analyze and permit the shortening of the design bond length for the production micropiles.

Jan 1, 2009

By Steve Kral

Despite low commodity prices and mining industry cutbacks throughout the world, Peru remains one of the industry’s bright spots. The country’s remarkable economic turnaround during the 1990s remains a model for other developing nations to follow. And the Peruvian government has not forgotten the industry that was instrumental in that turnaround. True, the country has not been spared the effects of the mining industry’s retrenchment that has occurred in other parts of the world. However, foreign mining companies remain committed to doing business in Peru. And the government remains committed to attracting foreign investment and maintaining a strong mining industry. This commitment was evident in September 1999during the 24th Convention of the Institutos de Ingenieros de Minas del Peru in Arequipa, Peru. More than 3,000 mining industry professionals from around the world attended the convention. And Extemin, the accompanying exhibit, featured more than 450 companies, many from the United States, Canada, Australia, South Africa and other countries.

Jan 1, 2000

By Robert H. Leach, C. H. Chatfield

This paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in conlmercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordaq4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. Analysis of Steeling Silver Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same ana,lysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry I1 in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

By J. W. Paul, J. N. Geyer

"GENERAL STATEMENTThe purpose of this report, which is the first of a series of three covering mines in the Fairmont district of West Virginia, is to give the result of a' study conducted in seal mines to ascertain the nature of the safeguards employed to prevent injury to the workmen from falls of roof and coal. In presenting the subject matter, consideration must necessarily be given to factors, features, and conditions such as method of mining, timber regulations and practices, supervision and natural conditions; and, for comparative purposes, a certain amount of statistical matter bearing upon the relation of fatalities and injuries to their causes, tonnage produced, men employed, days worked, and time lost.Those features and practices found to promote safe protection are summarized and suggestions made for such additional safeguards and practices as appear to give greater protection against injury from falls of roof or coal.ACKNOWLEDGMENTSThis study of falls of roof and coal in mines in Harrison County has been conducted by the U. S. Bureau of Mines in cooperation with R. M. Lambie, chief of the Mining Department of the State of West Virginia who assigned L. W. Brown, a district mine inspector, to assist in the field work and in the preparation of individual reports on each mine visited in this study. The writers acknowledge the helpful suggestions and cooperation given by these officials, the latter of whom assisted in the field work and prop red most of these sketches for the individual reports which wore submitted to the operator by the chief of the department. Thin report is a summary of the contents of the individual reports heretofore furnished the individual operator."

Aug 1, 1931

By O. Bernal, G. Velarde

Sociedad Minera Cerro Verde, majority owned by Phelps Dodge produces 200M lbs per year of LME Grade A copper from low cost leaching of secondary sulfides and SXEW processing. Central to the success of Cerro Verde has been the continuous improvement of leaching practices which currently yield over 80% recovery of the contained copper in the ore. This recovery has been achieved by careful attention to operational practices and leaching process fundamentals. This paper details the development of the concept of “Lixiviant Request Rate” where by solution is applied at an optimal rate for the grade, mineralogy, and the point in the leach cycle. Also paramount to the success of Request Rate technology has been the development of irrigation practices such as drip irrigation and irrigation grid design. These developments have ultimately resulted in improved copper production, decreased sulfuric acid and water consumption, decreased pumping cost, and more consistent PLS grades.

Jan 1, 2004

By C S. Szentesy, K Howie

The Rosia Montana gold deposit is located within the æGolden QuadrilateralÆ area in the Apuseni Mountains of Transylvania, Romania. The deposit is situated approximately 85 kilometres north of the regional centre of Deva, within the province of Alba, at elevations of up to 1100 metres above sea level. The Rosia Montana deposit contains a current resource of 344.07 million tonnes at an average grade of 1.3 grams per tonne (g/t) gold (Au) and 6.0 g/t silver (Ag) for a total (measured, indicated and inferred) contained resource of 14.29 million ounces of gold and 67.00 million ounces of silver. The resource was calculated using a 0.6g/t Au cut-off, a 10 x 10 x 10 metre block size and multiple indicator kriging. The low sulfidation style epithermal mineralisation at Rosia Montana is hosted within Tertiary age dacite intrusions and related vent breccias. Mineralisation is generally disseminated and associated with silica, adularia, illite, pyrite and carbonate alteration of host rocks, with minor late carbonate-base metal veins. Precipitation of precious metals is generally considered to have occurred as a result of over-pressurization, boiling and subsequent brecciation. The dacite intrusions are hosted in Cretaceous shallow marine and deltaic shales and slates, which overlie older Paleozoic sedimentary and metamorphic rocks within uplifted sections of oceanic sea floor.

Jan 1, 2002

Behaviour of Bubble Clusters in a Turbulent Flow

Sep 13, 2010

By Mauro Andrés Cerra Flórez

O presente estudo visa avaliar a resistência à corrosão de dois aços alto manganês com relação ao aço 9% Níquel em solução eletrólito 0,001M de H2SO4. Para esta pesquisa foram utilizados dois aços com teores de manganês de 22% e 26%, e a liga de aço 9% Níquel que é amplamente utilizada na indústria petroquímica. Os ensaios realizados para comparação da resistência à corrosão foram o monitoramento do potencial de circuito aberto (OCP) e polarização linear anódica. Foi escolhida a solução de H2SO4 pela presença do enxofre, oriundo dos campos de produção como impureza no gás natural. Foram utilizadas as técnicas de Microscopia Eletrônica de Varredura (MEV) e Espectroscopia de Energia Dispersiva de Raios-X (EDS) para a caracterização dos produtos de corrosão. Os resultados obtidos mostraram que os aços alto Manganês apresentaram valores similares de resistência à corrosão, mas ainda inferiores em relação ao aço 9% Níquel.

Oct 30, 2017

By D. Moradkhani

Copper metal has important role in the basic industrials, as if it did not exist, modern human life would not develop! Copper leaching, as the first step, is important step in copper production processes. In this research, efficient factors on the leaching have been investigated. For this reason, four efficient factors on leaching namely pH, liquid to solid ratio (L/S), temperature and time, as independent variables, were optimized using response surface (RSM) with D-optimal. A quadratic equation was used to create response and contours. According to the results from analysis of variance (ANOVA), the value of determination coefficient (R2=96.77%) indicates that the model was good fit. Optimum experiment condition also was found: pH of 1, L/S of 8.24, temperature of 26.06 ? and time of 43.64 min. At this condition, the maximum recovery of copper was equaled to 92/38 in which good desirability achieved.

Sep 1, 2012

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

Research on Universal Depressant of Talc and Serpentine

Sep 13, 2010

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

CONTENTS PAGE Simons, Theodore.-Basic Principles of Gravity Concentration-A Mathematical Study : :.. 1 Taggart, Arthur F. and Gaudin, A. M.-Surface Tension and Adsorption Phenomena in Flotation 11 Hersam, Ernest A.-Factors Controlling the Capacity of Rock Crushers 12 Shaw, S. F.-The Ore Deposits of Sierra Mojada, Coahuila, Mexico 12 Wilson, Philip D.-The British Columbia Batholith and Related Ore Deposits 26 Greensfelder, N. S.-Shot-firing by Electricity 27 Mitke, Chas. A.-Metal Mine Ventilation in the Southwest 28 Foley, F. B. and Howell, S. P.-Neumann Bands as Evidence of Action of Explosives upon Metals 30 Schwartz, H. A., Payne, H. R., Gorton, A. F., and Austin, M. M.-Conditions of Stable Equilibrium in Iron-carbon Alloys 30

Jan 12, 1922

By G Stanway, P Mahoney, C Griebel

The Mining Innovation – State of Play was initiated three years ago by VCI in partnership with the University of Western Australia. The ambition was to create a ‘think tank’ type platform to support industry discussion on how it is performing in terms of innovation at a strategic level, what needs to change in the industry ‘ecosystem’, and how businesses may more effectively develop their strategy and architecture to innovate for competitive advantage.The drivers for this ambition were straightforward. The industry recognises itself as being conservative with respect to innovation and it knows the business and community endowment dividend from getting better at innovation is large; however, much of the material that seeks to provide insight on innovation tends to be drawn from industries that do not have the same high capital, long life cycle and market uncertainty characteristics as that faced by mining. Material that does focus on mining innovation is orientated towards technical innovation, not innovation strategy. There exists a significant knowledge gap, and filling it is valuable to both mining businesses and communities.The 2014 Mining Innovation State of Play report (Stanway, Griebel and Mahoney, 2014), based on a survey of over 230 mining executives, uncovered a range of insights but left several questions unresolved. The people with the best perspective on these questions are CEOs. They can see the business issues with sufficient clarity and have the influence to shape both the industry and its organisations, as seen in Figure 1. Discussing these questions with the view to progressing our collective understanding was the primary reason this interview series was conducted.Unsurprisingly, interviewing 15 CEOs and Chairpersons from different industries and commodities, across the globe resulted in a broad range of views. The discussions were frank and often blunt in assessing the short comings in the industry and suggestions for improvement. This degree of candour is hugely valuable as a basis for improvement. In the end, four key areas emerged as a basis for improvement.CITATION:Stanway, G, Griebel, C and Mahoney, P, 2017. Mining Innovation State of PlayTM – iron ore insights, in Proceedings Iron Ore 2017, pp 439–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017