Search Documents

The corrosion of aluminosilicate refractories by soda from three different sources has been studied by microscopic methods. Sodium sulphate from oil ash, sodium chloride used in glazing structural clay products, and sodium borate from borax-impregnated wood ash have fundamentally the same effect on the refractories. The soda is the chief medium of reaction and fluxing, the sulphur, chlorine, and boron being volatized as sulphuric, hydrochloric, and boric acids.INTRODUCTIONBecause of their strong fluxing action, alkalis are one of the main causes of corrosion and slagging of refractories.The action of potash and soda on refractories follows somewhat similar lines, although it is common for one alkali to be greatly in excess of the other. The course of the reaction in a number of cases of alkali attack has been studied by microscopic and chemical methods. For example, the action of potash on blast furnace refractories was studied by Kraner (1942) and Rigby and Richardson (1947), who described the occurrence of various potassium aluminium silicates. Its action on cement kiln refractories was described by Brisbane, Segnit, and Weymouth (1957). The action of soda on glass tank refractories has been studied by many people, for example Bisby (1956) and Resch (1954). Clews, Hugill, and Green (1940) made a microscopic examination of the attack by soda on silica bricks from a gas retort.Some recent cases of corrosion of aluminosilicate refractories which were brought to the attention of the Division of Building Research, C.S.I.R.O., illustrate phenomena which occur under conditions different from those...

Jan 1, 1964

By C. V. Umipig, G. G. Hutalle, E. E. Israel

TVI Resource Development (Phils) Inc. Canatuan mine is a polymetallic ore deposit located in the Province of Zamboanga del Norte on the island of Mindanao in the Philippines. The deposit consisted of an oxidized capping of gossan overlying a Besshi type volcanogenic massive sulphide lens which is near surface and flat lying. Construction and development of a sulphide processing plant began in early 2007 and commissioned in November 2008. During the initial stages of sulphide operation, high copper (Cu)-low zinc (Zn) ore was fed to the plant. Marketable copper concentrate at 91-95% recovery was produced utilizing a high-pH bulk sulphide rougher flotation and 2 cleaning stages. Because of increased levels of Zn of the ore body, a Cu/Zn separation circuit was initiated in early 2010 following an intensive laboratory test work program. This Cu/Zn separation circuit was necessitated because of the copper ion pre-activation of the sphalerite that lead to the zinc being readily recovered to the copper rougher concentrate. In-situ activation of zinc (in the pit and stockpiles) was caused by the leaching of secondary copper minerals in the ore (particularly from the dominant copper species, chalcocite and covellite). This problem required the development of metallurgically complex and intensive reagent regime to effectively depress the activated sphalerite. As well, the immediate reactivation of zinc after it has been depressed, at the onset of Cu/Zn separation flotation, added additional metallurgical complexity to the process. Subsequent to the Cu/Zn separation circuit, an unconventional, yet proven effective, simultaneous cyanide detoxification-zinc flotation circuit was set-up to recover the zinc. Laboratory test work results realized Cu-Zn recovery differential from a Cu/Zn separation circuit of over 40-45%. This performance has been achieved in the plant, at 72% Cu overall recovery. With the gradual improvements on-going with zinc circuit capacity and effective zinc separation being achieved, zinc recovery has currently reached 40%.

Jan 1, 2012

By Marco Sonnenschein

As time is costly, engineering companies have developed methods, procedures and mechanical equipment to tunnel faster. But the best excavation method will not be able to cope with the time pressure if there is not a reliable backup system. Therefore, the application of belt conveyors for tunnel boring machine (TBM) drives as well as for drill-and-blast driven tunnels assure a quick and smooth removal of excavated soil in order to enhance the efficiency of the tunneling equipment. During the last 10 years, belt conveyor systems have achieved ?state-of-the-art? levels and have become the first choice for muck removal systems in both TBM and drill-and-blast driven tunnels. Because time has become such a key criterion in tunneling projects, it is essential that all equipment is operated so as to derive optimum efficiency and minimize costs. Efficiency also means to think about new tasks for existing technologies.

Jan 1, 2012

By Mike Amick

As virgin coal reserves dwindle, more and more mines are being opened in areas with previous mining. As addressed in this conference before, there are solutions available for designing mines extracting coal from reserves with known underground workings above or below the target seam. Often times, however, mining begins with limited knowledge of the underground workings. Even with careful planning, the proposed design has limited success because the ?facts? as presented during planning turn out not to be as accurate as one would like. At National Coal?s Mine #14, mining the Walnut Mountain seam, after driving the main entries in some 34 crosscuts, it was found during routine mine examinations that the pillars had separated from the roof in a few areas of the mains. Immediate roof conditions proved to be sound but questions arose concerning the stability of the main roof and floor. Core tests were done to better determine the rock strengths and characteristics. The paper presents the ideology used to tackle the effects of mining over old works in an operating coal mine. This paper discusses the analysis of the symptoms observed and the steps taken to ensure that this pillar separation was caused by the underlying old workings and that the separation was expected and controllable.

Jan 1, 2009

By Salvador Gómez, Rodolfo Espinosa, Jaime Bravo, Leopoldo Gallas

"Compañia Fresnillo, S.A. de C.V. - Proaño Mine, is owned by Industrias Peñoles S.A. de C.V. (Peñoles). The Proaño Mine, is one of the richest silver underground mines in the World, and for this reason, production capacity has always being expanded, based on generated reserves. Reserve generation has not being an easy task as this is a vein type deposit.This paper presents the growing stages at the Concentrator, for about the last twenty years; which can be listed as follows:1.,Increase in capacity from 1,000 to 4,500 tonnes per day, at several stages; on the same infrastructure, and without production interruptions.2.,Addition of a new flotation circuit to recover a zinc concentrate with a high silver content.3.,Installation of a semi-autogenous (SAG) mill, to replace a conventional crushing circuit. 4.,Modernization. Installation of an on stream analyser, an automatic reagent dosification system, 4500 ft3 unit cells, pressure filtration, a closed circuit video system to help process monitoring, an automatic ball addition system for SAG and ball mills, and on-line particle size analysers.5.,Silver recovery from old tailings, installing a 2,350 tonne per day treatment plant.INTRODUCTIONIndustrias Peñoles, S.A. de C.V. (Peñoles)Peñoles’ mission is to add sustainable value to non-renewable natural resources. Peñoles seeks to: build long-term shareholder value; provide customers with the highest quality product services; maintain productive long-term relationship with suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which operates; protect and preserve the environment."

Jan 1, 2002

By John E. Rourke, O&apos

This paper describes some of the results of a project for the design and demonstration of subsidence monitoring systems for underground coal mines. The project was designed to test monitoring systems described in an earlier feasibility report (O'Rourke and others, 1979). General objectives of the project were to develop reliable cost- effective monitoring systems for use above caving- type mining operations, over supported mines, and in urban undermined areas. Topics selected for discussion in this paper include a description of the instrumentation systems, the site conditions, problems of installation, resulting recommendations and an over- view of subsidence performance data obtained. There were some particularly difficult problems of installation to overcome at this site. Some of these could be experienced at any surface or under- ground project, others are probably more directly related to Western coal fields. Almost any subsidence monitoring program may face the following difficulties:

Jan 1, 1982

By McLeod RL

The Tolukuma gold-silver prospect is located approximately 100km N of Port Moresby in the Central Province of Papua New Guinea (PNG). Epithermal "adularia-sericite" style mineralisation crops out over 1200m within an en echelon quartz veined zone 1 to lOm wide. At a 4g/t cut-off grade, a geological resource of approximately 1.47Mt @ 13.77g/t Au is indicated from 38 diamond drill holes completed since discovery by Newmont Pty Ltd in September 1986. At a regional scale, Tolukuma miner- alisation appears localised in a dilatant zone at the intersection of a 1150 magnetic structure, and the western margin of a N-S trending graben which is filled by a Pliocene volcanic complex contemporaneous with the Mt Davidson Volcanics 30km to the W. A l0km diameter circular Landsat feature, which may reflect magma emplacement at depth, occurs immediately N of Tolukuma and nearby mineralisation. Mineralisation at Tolukuma occurs in sub-vertical quartz veins at, or adjacent to the faulted contact between Pliocene basic and intermediate volcanics/intrusives, and quartz mica schists and phyllites of the Cretaceous Kagi Metamorphics. Most veins display evidence of multiple episodes of brecciation and textures indicative of cyclic boiling, including crustiform rhythmic banding and quartz pseudomorphs after platy calcite.

Jan 1, 1991

Improvement of Phosphate Ore Flotation Performance Through Sized Flotation

Sep 13, 2010

There remains considerable controversy in the industry regarding precision type detonators and where the end user can benefit from their use. In spite of the fact that electronic detonators and other prototypes were tested over one decade ago, explosive suppliers have hedged on full scale production for many reasons. Although some of the reasons were based on solid economics, others were strongly influenced by shear internal resistance within the corporate objectives, ultimate fear of market rejection, indecision as to what degree of precision was required and limited data on defining the real benefits to the end user.

Jan 1, 1992

By R. M. Tyler

The importance of the heavy mineral sands to southern African economic well-being cannot be over emphasized. The value of the worldwide titanium dioxide industry is estimated at $7 billion. Six out of eight of the world?s proposed new project areas are in southern and eastern Africa, and a seventh at Tamil Nadu in India is partly owned by a South African company, Kumba Resources. The HMS industry can be highly lucrative; its return on capital is the best in the mining industry. There are, however, problems, particularly in the smelting technology. The often considerable affect of mining on environmentally sensitive coastal dunes is also becoming increasingly important. The medium-to long-term demand for Ti-dioxide pigment and ceramic grade zircon appears very healthy. If, as predicted, the costs of producing titanium metal can be reduced, then there is huge potential for the metal. In summary, the HMS industry is an attractive one to be in, with good returns and generally manageable risks. New business opportunities and their economic implications for Africa are discussed.

Jan 1, 2004

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By J. Y. Hascoet, M. Marya, S. Marya

Additive manufacturing (AM) brings disruptive changes over the ways parts and products are designed, tested, qualified, assembled, inspected and marketed. With these changes come real technical challenges, therefore, concerns that mainly stem from the maturity and diversity of today’s AM processes, the feedstock materials, and the interactions between the numerous process parameters. Additive manufacturing is somewhat similar to laser and electron-beam conduction-mode welding and involves a multitude of dynamic physical events between projected feedstock and moving heat source that influence process robustness, thus deposit properties. For this paper, a simple air vent, selected for its size, thin-wall, hollow geometry and materials (specifically 316L) was made using a laser-based powder blown technology (Construction Laser Additive Direct or CLAD) and systematically inspected by optical microscopy, microhardness indentations, and electron-back-scattering diffraction (EBSD). This exemplary part is first analyzed to broadly discuss metallurgical phenomena in additive manufacturing, particularly solidification and texture development. The paper then expands to other alloys and continues correlating metallurgical observations to process parameters and part properties, also borrowing from past experience with the same 3D printing CLAD system.

Jan 1, 2014

By G Eastwood, C Joyce, P Ryan, G M. Johnston

Over the years, predictive techniques for Acid Mine Drainage (AMD) and the natural processes affecting acid generation have received considerable attention. Less emphasis has been placed on the sampling strategy and the integration of testwork results with the geological data base. The sampling strategy employed and the development of a geological model to determine the spatial distribution and volume of acid producing material are often crucial for developing cost-effective containment and mitigation measures. The geological model provides a link between the occurrence, timing, destination and placement of mined waste rock. Careful and accurate interrogation of a comprehensive geological database provides this linkage. The AMD testwork program at Cadia in NSW has been designed to identify the temporal selective handling requirements that will be required during operation. Sampling involved collection of representative combinations of all waste rock types identified within an extensive geological database. These samples were subjected to static, kinetic and accelerated weathering predictive tests. Preliminary results have been used to construct a waste block model for the deposit that identifies the quantity and distribution of acid producing material. Integration of the block model with the mine scheduling determines when the material will be mined.

Jan 1, 1996

Unrelieved residual strains can influence the states of stress in rock masses. If cheap, stable structures are to be constructed in Tock in which large pressures are exterted by unrelieved residual strains, the pressures must be either utilized or neutralized. A photoelastic technique has been used to show that the release of residual strains in rocks is influenced by the mechanical properties of anisotropic rock fabrics. The relationships between directions of residual strain release and the attitudes of minor geological structures have been determined. For engineering design purposes it is possible to estimate the principal stress directions in rock containing unrelieved residual strains if the attitudes of such minor geological structures as foliation planes, lineations, and joints are known.INTRODUCTIONQuarry workers have long been aware that near-surface rocks may be highly stressed. In many cases the stresses are too large to be the result of gravitational loads. Dale (1923, pp. 34-35) gives many instances of deformation produced by the violent release of residual strains in quarry rocks. Coates (1963) has described powerful rock bursts and cases of rock deformation underground implying the existence of much larger stresses than are likely to result from present-day gravitational loads. The only explanation is that pressures of up to several thousands of pounds per square inch may be caused by unrelieved residual strains in rock.Instruments have been developed for measuring states of stress in rock masses. Most stress determinations in rock have been made on the assumption that rock behaves as a simple elastic material. It is now known that rock is a...

Jan 1, 1964

By J. R. Kadambi, E. Kucukal, J. Furlan

"Hydrocyclone separators are used in various industrial applications, including mining milling and tailings systems, in order to separate or classify solid particles and liquid droplets from multiphase systems. The flow within a hydrocyclone commonly used in the mineral processing industry was investigated numerically and experimentally using Particle Image Velocimetry (PIV) and refractive index matching techniques. The computational simulations were performed using a commercially available CFD package, STAR CCM+. Two turbulence models were used in the numerical calculations: the k-? model and the Reynolds Stress Model (RSM). In both cases, the first order discretization scheme was unable to resolve the flow characteristics accurately due to the high levels of numerical dissipation. PIV measurements were taken at various spatial locations along the cyclone. Both the numerical simulations and PIV data demonstrate that tangential velocities tend to increase when going radially inward from the cyclone wall towards the vortex finder, and reach a maximum value before they begin to decline rapidly and eventually become zero at the wall. The results also demonstrate the utility of non-axisymmetric approaches in cyclone flow simulations for a greater understanding of the fluid mechanics. The computational results were validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles. The comparisons demonstrated good agreement between the two models.IntroductionHydrocyclones are devices used to separate and classify solid particles or liquid droplets from liquid-solid or liquid-liquid systems. Versatile in application, they have been widely used in many industrial applications including the food, oil, power generation, chemical and mineral processing industries since 1891, when the first hydrocyclone was introduced by Bretney (Park, 2003). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2016

The concentration of Mt. Morgan sulphide ore has always been attended by serious loss of gold. Until recently, with a simple selective flotation flowsheet, even the lowest grade of ore milled-about 2 dwt. per long ton-thislloss was 0·9 dwt., whilst for average to high-grade ore, 3·5 to 5 dwt., the figure was 1·5 to 2·0 dwt. Early in 1937 it was decided to equip the research laboratory for an investigation into the condition and location of the escaping gold and the physical and mineralogical barriers preventing its recovery.With the completion of: this equipment in July 1937, trial and error testing, which had been explored to exhaustion, was abandoned and a five months' research programme mapped out and commenced. Based on the knowledge so gained, a flowsheet combining primary desliming, bulk flotation of the natural slime, selective flotation of the deslimed fraction, and cyanidation of the selective flotation tailing was drafted and tried with encouraging results in a 70-lb. per hour pilot plant. This flowsheet, modified to meet current circumstances, is being dove-tailed into the existing 1,500-ton sulphide ore concentrator, though the cyanidation treatment is actually carried out in the oxidized ore mill, to which the flotation tails are pumped.RESEARCH EQUIPMENT(1) Five tube elutriator (Fig. 1) t built in the company's workshop.

Jan 1, 1939

By W. P. C. Duyvesteyn, B. J. Sabacky

Reprinted with revisions from Extractive metallurgy of copper, nickel and cobalt, volume I: Fundamental aspects. ed. Reddy R.G., Weizenbach R.N. Warrendale, Pennsylvania: The Minerals, Metals and Materials Society, 1993. Development work on the Escondida process, concluding with the successful operation of an integrated leach-SX-EW pilot plant and a pilot flotation plant for the upgrading of leach residues, demonstrated that all major process objectives could be achieved. Extraction of 40% of copper in concentrates containing monovalent copper was achieved with essentially no oxidation of sulphide sulphur. The Cu contents of leach residues from four different types of concentrate were successfully upgraded to the original feed grades, giving a product that has potential as a high-quality concentrate for the smelter market. A compact solvent extraction section effectively recovered the ammonia lixiviant for recycling to leaching and selectively transferred Cu into a conventional acid sulphate electrowinning system. High-quality "six-nines" copper cathode was produced on commercial-scale stainless steel blanks, demonstrating that the process will be able to compete effectively in the premium cathode market

Dec 1, 1995

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

The Río Agrio of northern Patagonia, Argentina, is highly acidic due to inputs of volcanic gases (SO2, HCl, HF) in its headwaters. The watershed includes a hyper-acidic (pH <0.5) volcanic crater lake, a larger glacially carved lake that is also strongly acidic (pH 2.6 to 2.7) and an acidic river that flows for more than 40 km (25 miles) before its pH is completely neutralized. This unique watershed has many geochemical and biological similarities to acid waters caused by mining. This paper describes the Río Agrio watershed and draws a comparison with some famous acid mine waters. Learning more about naturally acidic lakes and river systems could have important applications to the bioleaching of ores or biological treatment of mine waters. Therefore, it should be of interest to the general community of mining and metallurgical engineers.

Jan 1, 2008