Search Documents

By Erkan Bayrak, Serkan Erkara, Ozkan Duzgun, Ekin Gungor

This paper presents part of the outcomes of the drill and blast optimization project carried out at Kisladag Gold Mine in Turkey. Kisladag Gold Mine is the largest gold mine in Turkey with a low-grade, bulk-tonnage, open pit operation that uses heap leaching for gold recovery. After blasting, the ore is fed to a three-stage crushing circuit which prepares crushed ore approximately -10 mm (0.39 in) for heap leaching. Crusher downtime analysis showed that blocky material and insufficient feed are causing significant downtimes with the primary crusher. This was supported by the fragmentation data collected to date. It was decided to initiate a fragmentation project to understand the variation in the run-of-mine (ROM) size with a view to provide a consistent feed to the crushing circuit. The study includes the analyses of the ore strength and structure, image analysis of the fragmentation pictures acquired from blasts, blast auditing and quality assurance and quality control (QA/QC) analyses. During this project, over 200 fragmentation pictures were acquired from 47 blasts to optimize ore and waste blasts. Ore strength varies between 30 and 120 MPa and rock quality designation (RQD) ranges between 30 and 100. A site-specific fragmentation model was used to calibrate the fragmentation for blast domains formed. In addition, alternative cases were simulated to achieve blasts designs with consistent ROM fragmentation size distribution. Alternative blast designs that include stemming length and powder factor changes were suggested. Long stemming length, drill cuttings use, free faced blasts, small shot sizes and poor stemming length control were some of the key issues causing coarse fragmentation.

Jan 1, 2015

By R A. Binns, S Murao

The PACMANUS and Jade deposits are two active hydrothermal fields that are forming massive sulphide deposits at the Pacific rim margin. Both are associated with felsic submarine volcanic rocks and both occur in back-arc settings. However, PACMANUS is associated with almost sediment-free dacites and lies on the crest of a volcanic ridge, whereas Jade occurs in a heavily-sedimented tectonic depression associated with a basement of pumiceous rhyolite. The PACMANUS deposit is richer in Cu and Au, and Jade in Pb. Zinc, Ag, As and Sb contents are similar. Sulfide textures at PACMANUS suggest formation of Cu and Zn sulfides by simultaneous double-diffusion involving inwards-moving seawater mixing with outwards-moving hydrothermal fluid. By contrast, at Jade there is a more complex history of formation where initial growth of barite on the sediment surface, probably associated with microbial activity, formed an impervious cap which trapped higher temperature hydrothermal solutions.  

Jan 1, 1995

By J. C. Carrasco, M. Sánchez, R. Jara, F. Marquez, F. Parada, R. Parra, J. Palacios

In past years, Chile has been the largest copper producer in the world and for 2002 mining represented country average of 10 % of the GDP, accounting for 47 % of the total exportation. As copper sulphides are the main mining resources in the country, the metal is produced using the classical processes of flotation and pyrometallurgical extraction. Seven copper smelter plants, which extends from the northern Atacama desert to the central part of the country produced1,522,000 metric tons of fine copper in 2002, approximately one half of total copper concentrate production, with a notorious environmental impact due to the great amount of slag produced during these extraction steps. In this work, a global characterization of copper pyrometallurgical slags produced and disposed of in Chile and worldwide is done, and the concept of total project development is considered to explain the scopes of the study, recovering different compounds and generating new activities around mining. The presentation is completed with the proposal of various methods and techniques being developed today in a joint project between smelter plants and the University of Concepción, with the support of the Chilean government and mining companies, addressed to generate new materials from copper slag. Recovery of copper, molybdenum, precious metals, silica and iron, that is the most abundant component of the slag, are the goals for this research. Metals, commercial compounds, alloys and different forms of iron oxides for steel industry are proposed products.

Jan 1, 2004

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at 'any of several stages of extraction and processing, the stage of measurement used In this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the product of auxiliary processing at or near the mines.

Jan 1, 1977

By Andy Alder

The Docklands Light Railway (DLR) Extension to Woolwich Arsenal provides a much-needed public transport link to this area of London. The project includes construction of 5.3mID running tunnels under the River Thames, in ground conditions that proved challenging for the Earth Pressure Balance Tunnel Boring Machine (TBM). The project also includes cut and cover tunnel approaches, an underground station, and an emergency shaft on the bank of the river. Major challenges have included tunneling under sensitive infrastructure, and working adjacent to existing operational railways at Woolwich Arsenal. This paper will describe the design and construction of the project and how these challenges were overcome.

Jan 1, 2008

By F. N. Kissell, C. M. McCulloch, Maurice Deul, J. R. Levine

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas content of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and desorbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

The cost of preparing a feasibility study is notoriously difficult to estimate. Studies for mining projects are typically commenced when an exploration programme has identified a mineable resource and pre-feasibility studies have shown that development of the resource would lead to an economically viable project. Pre-feasibility studies will normally include an estimate of the cost of a formal feasibility study and this estimate would then be firmed up before a commitment is made to proceed with the formal study. Data for preparing the feasibility study cost estimate will be sketchy, geological investigations, metallurgical testwork, and marketing studies may be needed before the scope of the project and hence the scope of the formal study can be finally determined. Before an estimate of the work required and hence of the cost of the feasibility study can be prepared the source of project funds must be decided. Studies for internally funded projects are often less rigorous than those which must be "bankable" and subject to the scrutiny of external financial institutions. This paper sets out suggestions for preparing more accurate cost estimates for feasibility studies by ensuring that all activities are included and shows how a staged approach to preparing such studies can minimise costs and guard against cost overruns. It also provides a case study showing how the estimate compared with actual costs for a recent feasibility study completed by Pancontinental Mining Limited.

Jan 1, 1990

By P. N. Anyalebechi

The effects of solidification rate (0.4-26.1 K/s) and alloying elements on the cast microstructures of aluminum alloy 5182 have been investigated with directionally cooled laboratory-size ingots. The alloying elements examined included Mg (3.6-4.7 wt.%), Mn (0.35-0.75 wt.%), Fe (0.11- 0.42 wt.%), Cu (0.03-0.25 wt.%), and Si (0.11-0.28 wt.%). These reflect the chemical compositions of AA 5182 end stocks with high recycled used beverage container (UBC) content. For a given chemical composition, the average dendrite cell and constituent phase particle size decreased with increase in average solidification rate. In general, within the level investigated, Mg did not have a significant effect on the types, volume fractions, and average sizes of the constituent phase particles. However, increase in Mn, Si, Fe, and Cu increased average sizes and volume fractions of the constituent phase particles.

Jan 1, 2010

By Horacio Reeves

Las maquinarias son elementos importantes en el proceso de minería de tajo abierto -en tanto optimizan el rendimiento del trabajo y de los operarios. Sin embargo, su contínuo uso conlleva riesgos ocupacionales en el trabajador como la exposición a vibraciones de cuerpo entero en el caso de equipos pesados. En ese sentido, el presente texto compara los niveles de vibración en los equipos pesados que operan en Antamina con el estándar europeo: Directiva 2002/44/CE, así como los efectos de este en los operarios.

Sep 12, 2005

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

This paper pays tribute to the pioneers in geomechanics, and addresses some of the most pressing issues of our time related to deep mining, and how to mitigate these issues. Solutions developed by our predecessors seem to have reached their limits as mines continue to go deeper. The International Society for Rock Mechanics (ISRM) guidelines for rock mass characterization for excavation design also require re-thinking to reflect current knowledge and experience. Thus, a whole new approach is urgently required to increase mine safety and productivity. The paper will draw on the challenges and experiences in medicine and science that have been overcome through genuine collaboration, advances in technology, and impressive funding, which can be adopted to provide solutions to contemporary geomechanics challenges for increased safety and productivity as mines continue to go deeper.

Jan 1, 2014

By Kyoosang Yoo

The report presents the results corresponding to the analysis of a lining system for tunnels in soil and soft rock in creep-active ground. The purpose of the analysis is to evaluate the performance of a lining at each construction stage. The steps include: 1. Accurate representation of the initial undisturbed state of stress 2. Excavation, 3. Lining installation 4. Injection of mortar and its curing, and 5. Short-, medium- and long-term creep behaviour in the surrounding soil/rock. The response of a prototype tunnel is simulated using the computational finite element framework MSC.marc2008.

Jan 1, 2010

By K. Oraee

Rate of penetration of Tunnel Boring Machines (TBM) has a significant role in the planning, measurement of productivity and performance of any tunneling project. In this paper, the application of Adaptive Neuro Fuzzy Inference System (ANFIS) in prediction of TBM penetration rate is evaluated. For this purpose, a database including Rock Quality Designation (RQD), Uni-axial Compressive Strength (UCS) of the rock, the Distance between Planes of Weakness (DPW) in the rock mass, and empirical data regarding rate of penetration of TBM from several tunneling projects are collected. The Rate of Penetration is then estimated by using ANFIS. These results are then compared with measured TBM penetration rates (actual data). It is concluded that ANFIS can be applied successfully for such purpose and result in high accuracy for prediction for the rate of penetration of TBM. The method provided in this paper can assist the mining engineer to estimate the performance of tunneling accurately.

Jan 1, 2012

By M. Keen

The backfill system at Cleveland Potash?s Boulby Mine places waste filter cake underground in the form of a high concentration slurry in worked out areas of the mine reducing the mine?s environmental impact. The backfill system delivers slurry approximately 1100 m down the mine and up to 11 000 m horizontally underground. The Boulby backfill system is unique in that the placed backfill waste is not used for the usual purposes such as support, pillar extraction or reducing ventilation requirements. It was specifically implemented for environmental reasons. This influenced the design and resulted in some unique features of the system. A previous paper (Wilkins et al., 2004) described the design and commissioning of the backfill system. This paper describes the operational experience with the backfill system and backfill placement since commissioning in May 2003 and looks at lessons that can be applied in other backfill designs.

May 1, 2007

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

The following Inventory was prepared to provide mineral deposit data to the U.S. Army Corps of Engineers for use in the Resource Development Navigation Study in Alaska. The inventory was prepared using data contained in the U.S. Bureau of Mines Minerals Availability System (MAS) database. The Alaska portion of the database contains Information on over 7,000 mineral locations and deposits throughout the state. When MAS was established In 1975, database entries were originally compiled from literature searches by both Bureau personnel and contractors. Deposit data are obtained/maintained through Information gained from a variety of sources, Including published and unpublished Bureau of Mines reports, records, and files; U.S. Geological Survey (USGS) Bulletins, Professional Papers, and other reports; technical and professional Journals; State and other Federal agency publications; data generated during field examinations; and information obtained from knowledgeable individuals. Because of the size of the data base, many of the data have not been significantly modified since initial entry. Each deposit on the MAS data base has a sequence number of the following form:

Jan 1, 2011

By J. T. Nel

The establishment of a pilot plant for the continuous production of titania pigment and nano-titania is discussed. The plant was designed, constructed and operated on the Necsa site. The TiO2 production capacity is 7?10 kg.h-1 by the reaction of TiCl4 and O2at>1000°C. Liquid TiCl4 is sprayed under pressure into a plasma reactor where it evaporates and reacts with O2 to form TiO2. Process optimization has allowed for continuous production without any clogging or blockages. The primary advantage of the plasma-assisted process is the possibility to recover and recycle the chlorine values in high yield as Cl2 for use in the manufacture of TiCl4. The HCl formed in most conventional fossil-fuelled processes makes Cl2 recovery and recycling much more difficult. Particle size distribution analysis of the fine, white product revealed a d50= 125 nm. The raw product consisted of 60% rutile that could be increased to 80?100% rutile by post-annealing. The specific surface area (SSA) of the pigment was 8?20 m2?g-1(BET). According to the CIE colour index the ?whiteness? (L*>95) of the plasma-produced pigment was better than that of several commercially available pigments. The particle size could be manipulated by controlling the TiCl4 feed rate, gas flowrates, and the particle quench rate and residence time. Nano-sized TiO2 powders with a particles size (d50) as small as 50 nm were also successfully produced in this way.

Jan 1, 2010

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978

By Hookings H. J

UNDER a contract relating to the sale of a Broken Hill concentrate, the differentiation between granular and slime concentrate is determined by the proportion of the material which will pass a 200-mesh (I.M.M. standard) screen, and this has led to considerable attention being devoted to the question of laboratory sizing tests with screens of this order.It was found that many of the screens turned out by the makers during the war, and also since its termination, did not conform with the I.M.M. specifications as closely as some supplied in pre-war days. A perfect screen is hardly to be expected, but when the above contract was framed the parties anticipated that, by special care being taken during manufacture, a screen at least as good as the best pre-war screens would be available. This, however, has not proved to be the case, and the large irregularities in screens recently supplied render them useless for sizing determinations under the contract. The makers were approached through the Institution of Mining and Metallurgy, London, with the view of obtaining a few screens conforming as closely as possible to the 200-mesh I.M.M. standard, and in response to a request twelve pieces of screen were...

Jan 1, 1922