Search Documents

By Jennifer Riefenberg

Research efforts by the U.S. Bureau of Mines include running a series of displacement-discontinuity, boundary-element models to simulate the gateroad design at an underground coal mine in northwestern Colorado. The initial mine design is a yield-abutment chain pillar arrangement in a three-entry, longwall gateroad system. Pressure effects from mining the first and second panel were recorded using borehole pressure cells (BPCs). These field data were then compared directly to the model output. Observed yielding in the field was approximated by reducing material property values and/or removing pillar elements in the model. Model results using this calibration technique mirrored the field measurements consistently. Using the calibrated model parameters, a suite of models was run simulating an experimental entry design: exchanging the yield and abutment pillar locations. These model results reflect a 20¬to 33-percent reduction in core stresses in the yield pillar during mining of the second panel. Improved pillar and entry conditions are suggested by these predictive results. The design modifications were then implemented at the mine along a 150-m (500-ft) test section. Field observations and measurements from the experimental design test site compared favorably with trends of the model predictions.

Jan 1, 1993

By I. R. Kramer

I. R. Kramer (Martin Co.)—In a recent paper Nakada and Chalmers24 reported some observations of effects of surface conditions on the stress-strain curves of aluminum and gold single crystals. It is of interest to compare these observations with the results published previously in this journal and to comment on their general conclusions. In brief, Nakada and Chalmers concluded that the removal of the surface layer of a prestrained specimen lowered the stress-strain curve for aluminum but not that for gold. Further, they concluded that the surface work hardening of aluminum is confined to a depth not more than l0-3 cm. In our results25 published previously, it was pointed out that when prestrained specimens of aluminum and gold were polished to reduce the thickness upon reloading the initial flow stress decreased markedly. Further if a sufficient amount of metal was removed, the yield point failed to appear. With continued application of the load the stress-strain curve became coincident with that of the virgin crystal. We have found this behavior in some 100 determinations to hold consistently for gold, aluminum, and copper in both single and poly-crystalline specimens. The amount of strain required before the curves coincided depends upon the amount of metal removed but it is usually less than 0.01. This type of behavior is the same as that reported for metarecovery by other investigators.29 For aluminum specimens which have been prestrained and then heated to temperatures above 50°C we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen. With respect to Ref. 24 the curves for aluminum are always below that of the virgin curves, while those for gold become coincident. This observation indicates at least for aluminum that the specimens must have been heated to a temperature high enough to cause recovery by an alteration of the internal dislocations. In addition, a recovery would be expected because of the removal of the surface work-hardened layer. Nakada27 had reported that, with his particular apparatus in which a perchloric acid polishing solution was used, the temperature of the specimen increased 65°C. The curves presented in Ref. 24 for gold do not permit one to detect the initial flow stress upon reloading after the surface-removal treatment. In fact, contrary to the method used by Nakada and Chalmers, the change in the stress-strain curve produced by a surface-removal treatment cannot be described in terms of a decrease in stress at strains much higher than that at the initial flow stress because of the coincidence of the curves at the higher strain values. With regard to the depth of the work-hardened surface layer, our data show for aluminum single crystals (7.5 by 0.3 by 0.3 cm) that the initial flow stress remained constant after 12 x 10-3 cm had been removed from the thickness. This depth was independent of the prior strain. For gold crystals this depth is somewhere between 10 x 10-3 and 20 x 10-3 cm. Y. Nakada (author's reply)— Kramer states,28 "for aluminum specimens which have been prestrained and then heated to temperatures above 50°C, we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen." However, Cherian et a1.26 discovered that aluminum polycrystals annealed at 32" and 100°C showed the metarecovery behavior. They showed that the orthorecovery behavior did not appear until the crystals were annealed at 150°C. Kramer suggests28 that the drop in the flow stress of aluminum crystals after the surface removal by electropolishing24 may be due to the recovery caused by the temperature rise which may occur during the electropolishing.27 However, as indirectly stated in Ref. 24, the current density used in these electro -polishing experiments was 0.15 amp per sq cm. According to ref. 27, this current density should cause a temperature rise of only 40°C. This may cause the metarecovery but not the orthorecovery. Furthermore, as stated explicitly in Ref. 24, the surface removal was accomplished by chemical etching as well as by electropolishing. The results were the same for both electropolishing and etching. During the etching, the specimen temperature did not rise above 35°C. Some aluminum crystals were placed in water at 35° C for 30 min. These crystals did not show the decrease in flow stress. Therefore, it is quite clear that the flow-stress drop after the surface removal is not caused by a high-temperature recovery. However, as Kramer points out,28 it is quite possible that the internal dislocation structure may have been altered because of the removal of the highly work-hardened surface layer. However, how much this rearrangement contributes toward the flow-stress decrease is not known at present.

Jan 1, 1965

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author's aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.' It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961

By Jochen Petersen, Diane Taggart

"At an average of 90.3% (for the period of 1 January 2009 to 30 September 2011), Zincor’s zinc recovery was well below the industry standard of 96%. The losses through the residues, in particular the iron residue, were the biggest contributors to the overall zinc loss. It was believed that this loss could be decreased with the implementation of seed recycling. A plant trial was run to test the implementation of a seed recycle. The rate of seed addition through recycle was increased over a 4-week period. The presence of seed decreased the insoluble zinc loss by providing additional surface area for iron to precipitate onto, and reducing coating of unleached neutralising agent. The soluble zinc loss was also decreased at low and moderate seed recycle volumes. The improvement was attributed to agglomeration growth of the recycled particles, which improves the dewatering characteristics of the precipitate. In contrast, the soluble zinc loss increased at high seed recycle rates. This result was attributed to particle crowding and a low wash ratio.INTRODUCTION The Zincor refinery, which closed in December 2011, was situated just outside of Springs in the Gauteng Province of South Africa and employed the conventional Roast-Leach-Electrowin process, which accounts for 75 to 80% of the annual primary zinc production in the world. The refinery fed up to 220 000 t/a of zinc sulphide concentrate. The major portion of the raw material was sourced in Southern Africa from the Rosh Pinah and Black Mountain mines. Between 20 000 and 40 000 t/a of material was imported to make up the deficit and to improve the grade of the feed material. The iron contained in the zinc concentrates, at an average of 6.03% (for the period of 1 January 2009 to 30 September 2011), resulted in the formation of zinc ferrite during roasting, which is insoluble under atmospheric leach conditions. At Zincor, most of the zinc ferrite was dissolved in the residue treatment plant at elevated temperature and high acid strength. The leach liquor from this aggressive leach contained between 15 to 30 g/L of iron, mostly in the ferric form, and was known as the hot iron solution (HIS). The presence of iron in the liquor had an adverse effect on the zinc operation, particularly on the current efficiency in the electrowinning circuit. Therefore the iron needed complete removal."

Jan 1, 2016

The optimum cut-off grade policy maximizes the net present value (NPV) of an open pit mining operation subject to the mining, processing, and refining capacity constraints. The traditional approaches to cut-off grade determination ignore the escalation of the economic parameters such as metal price and operating costs during life of an operation, and consequently lead to unrealistically higher values of the objective function. Further, the NPV of a mining operation declines due to the depletion of the available reserves, causing a decline in the optimum cut-off grade, i.e. higher cut-off grades in the early years of an operation and lower cut-off grades during the later years. Hence, low grade material mined in the earlier years may be stockpiled for processing during later years to offset the effect of escalating economic parameters on NPV. This paper demonstrates the combined impact of introducing economic parameters, escalation and stockpiling options into the cut-off grade optimization model. The model promises an enhancement in NPV as illustrated in a case study incorporating practical aspects of an open pit mining operation.

Jan 1, 2011

By J. Durkin

The Bureau of Mines has conducted field studies in coal mines throughout the United States to determine the effectiveness of electromagnetic techniques in locating miners trapped underground following a mine accident. Data from these tests have been used to generate models of expected signal and noise distributions as found above these mines. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results show that at a 10% false-alarm rate, the expected probability o detecting a miner's signal" from a depth of 1000 ft is 54% at 500 ft it is 95%. These depths exceed the actual depths of 90 and 50%, respectively, of United States coal mines. Sensitivity studies have shown that at depth of 1000 ft, the probability of detection will improve approximately 2% for each dB of increase in signal-to-noise (SNR) ratio.

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By Thornton L. Neathery

Vertical magnetic surveys have been made over about 3, 150 miles of the crystalline area of east-central Alabama. A contour map (100-gamma interval) showing regional magnetic anomalies has been prepared (scale 1:250,000) from data points located at quarter-mile intervals on all public roads. Small one- and two-station anomalies were eliminated, leaving only areally extensive anomaly features associated with regional geology. The regional gradient was "filtered" from the basic data and the resulting magnetic configuration compared to the regional geology. Regional lines of vertical magnetic intensity trend northeast and follow the structural framework of the area. Correlations can be made between a large number of geologic and magnetic features. The strongest regional anomalies are associated with the Goat Rock, Bartletts Ferry, Towaliga, and Brevard fault structures. The Inner Piedmont area is characterized by a broad regional high. The magnetic values of the northern Alabama Piedmont grades gently northwestward, disrupted occasionally by elongate highs and lows associated with amphibolites or granites. Scattered throughout the Piedmont are anomalous areas of high magnetic intensity; some are related to magnetic-bearing rocks, and some Indicate possible mineralization. Most of the anomalies have not been evaluated,

Jan 1, 1972

By G. M. Bond

Reduction of the emissions of greenhouse gases, such as CO,, is currently the subject of extensive research. A novel strategy is put forward here, based on a biomimetic approach providing accelerated deposition into carbonate form for long-term sequestration. It offers the advantages of a process that: does not require concentration of CO, from flue gases; could potentially be used in an on-site scrubber to provide a plant-by-plant solution to reducing CO, emissions; is an environmentally benign procss with an environmentally benign product; and is based on readily available, low-cost reagents (except perhaps the catalyst).

Jan 1, 1999

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting, and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power input over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge that was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified 'chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2012

By A Jäger, J L. Lett, J Rachocki and B Mobilio

The Newcrest Mining Limited Cadia East Panel Cave mines near Orange, New South Wales, Australia commenced production 1200 m below the surface in May 2014. Understanding the mine-wide impact caving had on excavation stability was a primary objective to ensure a safe working environment as production ramped up in the Panel Cave 1 operation and establishment activities were implemented in Panel Cave 2. The impact of cave interaction between Panel Cave 1 and Panel Cave 2 and establishing monitoring systems to assist mine planning and production as both caves joined is explained in this paper. Monitoring tools such as a microseismic system, open holes, HI-cells, extensometers, fibre optic sensing, cave markers, closure monitoring, underground observations and damage mapping were used to characterise the performance and position of the cave back. The data and observations collected were compared to predictions from numerical and empirical methods and used to calibrate the numerical models for forward prediction and to develop site empirical design tools. The results and methodology for monitoring deep high-output caves are the key discussion points in this paper.CITATION:Lett, J L, Jäger, A, Thornhill, T, Rachocki, J and Mobilio, B, 2016. Geotechnical challenges in cave monitoring – a modern approach, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 203–216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Xiaofei Guan, Adam C. Powell, Uday B. Pal, Srikanth Gopalan

This paper reports a solid oxide membrane (SOM) electrolysis experiment using an LSM– Inconel inert anode current collector for production of Mg and O2 at 1423K. The electrochemical performance of the SOM cell was evaluated by using various electrochemical techniques including electrochemical impedance spectroscopy, potentiodynamic scans, and potentiostatic electrolysis. The effects of Mg solubility in the flux on the current efficiency and the YSZ membrane stability during SOM electrolysis were discussed and examined through experiment and modeling. The electronic transference number of the flux were measured to assess the Mg dissolution in the flux during SOM electrolysis. A negative correlation between the electronic transference number of the flux and the current efficiency of the SOM electrolysis was observed.

Jan 1, 2014

By R. Dewey

WHAT IS AI? It's very hard to say. Most researchers and practitioners disagree with nearly any attempted definition, but most would agree that A1 does deal with the development of computer-related methods o f problem-solving. Artificial intelligence is a discipline which seeks to emulate human anatomy and/or thought processes by applying computer science, electronics, and mechanical engineering to the development of natural language processing, machine vision, robotics, and knowledge-based expert systems. Integration of these four fields will someday produce the robots of today's science fiction. A1 addresses problems of structuring large amounts of knowledge and representing relationships with rules and semantic frameworks rather than with mathematical equations. A1 is convergent rather than divergent - - conventional conputer applications use relatively small quantities of input to generate large output, but A1 generally reduces large amounts of information to establish a few major conclusions. The development of A1 has prompted greatly increased efforts on the part of scientists and engineers to understand just how humans think, organize information, approach problem-solving, and form conclusions. Some of the more exciting and possibly far-reaching advances in A1 are coming in this more-or-less soft-science area. Thirty years of A1 research (dating from a 1956 conference at Dartmouth College at which the term A1 was coined) has already spawned many widespread, almost ordinary, products: window graphics, hand-held controllers (mouse). function menus, etc., all in an attempt to make computers and people more compatible. WHAT IS AN ES? A1 can be used to develop EXPERT SYSTEMS, which are computer programs or systems which contain knowledge and rules by which problems can be solved. or at least by which possible solutions can be suggested for very complex problems. A1 can be used to better define problems so that solutions can be found. An ES is designed not to process numbers, but to process information according to rules and logic derived from actual practice and experience. WHY AI? WHY ES? Companies are increasingly aware of the value of accumulated knowledge and experience in designing, building, operating, and maintaining the increasingly complex or expensive physical plants in any business. As knowledge branches out and becomes more specialized, the accumulated learning of a veteran operator or manager or engineer becomes a scarce resource well worth preserving. EXPERT SYSTEMS offer a means of doing that, reinforcing, not replacing, human capabilities.

Jan 1, 1987

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 177,000-acre Secesh study area; most of the area had been proposed as wilderness. Bureau personnel mapped and sampled several hundred mine and prospect workings; 1,715 rock, soil, and placer samples were taken during the investigation. The study area is centered about 25 mi east-northeast of McCall, Idaho, in the Payette National Forest. Five mining districts extend into or are adjacent to the study area. There have been more than 3,000 mining claims located inside the study area, 884 are current. In excess of $17 million (historical value) in placer and lode gold has reportedly been produced from the Warren district alone. The study area contains gold, silver, copper, lead, zinc, tungsten, and antimony. At least six properties that would be in the proposed wilderness contain gold resources; more than 18 million tons averaging 0.038 oz/ton gold have been identified. Additional resources may be located at 4 other localities. The 4th of July mine is currently producing gold/silver/lead ore. Similar resources may be located on at least 3 other properties. Placer samples from the study area contained up to 0.34 oz gold/yd3 ($120/yd3). The samples are representative of relatively small occurrences and do not constitute resources; small quantities of gold may be recovered by recreational placer miners.

Jan 1, 1993

By Cínthia Toshimi Ogata

Processos de fundição de ligas de alumínio com altos teores de Mg são um desafio da indústria, uma vez que diferentes taxas de resfriamento ocorrem em geometrias diversas. Este trabalho tem como objetivo caracterizar a liga de alumínio AA5052 com variações em teores de Mg por meio de experimentos de solidificação direcional transitória, e compreender seus efeitos com relação a evolução de parâmetros térmicos, microestruturais, e propriedade mecânica. As leis experimentais de evolução do espaçamento dendrítico primário (?1) com relação a taxa de resfriamento resultam em: ?_1=640 ?T ?_L?^(-1/4) para a liga 5052 com 2,4%Mg e ?_1=300 ?T ?_L?^(-1/4) para a liga com 3,2%Mg. As leis de crescimento de espaçamento dendrítico secundário (?2) com relação a velocidade de solidificação resultaram em: ?_2=27 ?V_L?^(-1,1) para a liga 5052 com 2,4%Mg e ?_2=15 ?V_L?^(-1,1) para as ligas com 2,6%Mg e 3,2%Mg. Maiores teores de Mg na liga AA5052 proporcionaram uma expressiva redução no valor de ?2 para uma determinada VL. A evolução da dureza mostrou-se diretamente relacionada ao tamanho e a distribuição dos intermetálicos presentes, sendo ?2 o fator predominante neste controle.

Oct 30, 2017

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By R Adamian, F. T. Da Silva, D. H. Gameiro

Schytill and Geldart diagrams were developed for the TiO2-C-Cl2 system at 1 073 and 1 273 K, so as to define the hypothetical relations between particle sizes and chlorine velocity for simultaneous fluidisation of mixtures of anatase concentrate and charcoal for carbochlorination. It was concluded that the operating limits on chlorine gas velocity will be controlled by the behaviour of the reducing agent, mainly because of its lower density. An increase in temperature from 1 073 to 1 273 K will have only a small influence on the fluid-dynamic behaviour of the mixture. For bubble fluidisation, the maximum sizes 0.413-0.478 mm for anatase and 0.529-0.611 mm for charcoal will be adequate. When the particle size distribution is large, fluidisation will be feasible only if conducted in two stages, otherwise the residence time of the small particles in the reactor will be very short. New diagrams will be needed for the gaseous chlorides in the second stage

Jun 21, 1905

By W. C. Winegard, A. Galibois, C. J. Beingessner

The effects of solutes on the distribution of two-dimensional configurations of grains in zone-refined tin have been studied. When solutes with partition coefficients (ko) greater than unity are added, three-sided pains become more prevalent and the growth law changes. It is shown by electron-Probe micro-analysis that a solute buildup occurs ahead of a moving grain boundary when ko > 1. It has been found recently1, 2 that solutes with partition coefficients greater than unity have a larger retarding effect on grain growth than solutes with k, less than unity. ko is defined as the ratio of the concentration of solute in the solid to the concentration of solute in the liquid with which the solid is in equilibrium. Niessen and winegard2 have suggested that this effect is probably due to the complex shape changes which occur during the process of grain growth and that no theory based on single boundary motion3-5 can explain the results. They suggested that the dissociation of the unstable fourfold junction was delayed in alloys where ko was greater than 1 because the boundaries at the junction had to move into a region of high solute concentration. If indeed this mechanism were correct, it was felt that not only would the dissociation of fourfold junctions be affected by the solute buildup ahead of the boundaries, but the collapse of three-sided grains would be impaired. These combined effects would naturally lead to a modification in the distribution of the number of sides per grain seen on a two-dimensional section. The present investigation was undertaken to test these hypotheses by examining the grain-growth process in detail. EXPERIMENTS The Distribution of Grain Configurations in Zone-Refined Tin as Seen on a Two-Dimensional Section. Following the method of Bolling and Winegard,6 zone-refined tin was cast into button-shaped specimens and, subsequently, plastically deformed under a drop hammer at room temperature. The resulting flat coin-shaped samples were annealed at 200°C, some for 50 sec and others for 100 sec. The specimens were then examined to determine the distribution of the number of sides per grain, i.e., the num- ber of crystals adjacent to any particular grain in the section. For simplicity, the grains were classified as three-sided, four-sided, and so forth; this concept is schematically illustrated in Fig. 1. As indicated by smith,' it was necessary to examine every grain within an enclosed area to obtain a proper distribution of the relative frequency of each type. The distributions for the two annealing times are illustrated in Fig. 2. The total number of grains examined is also indicated on the figure. It is evi-

Jan 1, 1965