Search Documents

The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill?s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.

Jan 1, 2009

By Pavel Vasak

Microseismic monitoring has become standard practice in the mining industry as a ground control monitoring tool at depth. Translating the information into practical hazard assessment tools for the rock mechanics practitioner is the focus of research jointly conducted at Creighton Mine by INCO Mines Technology Centre (MTC) and the Geomechanics Research Centre (GRC) in Sudbury, Ontario. Rock mass damage mechanisms are typically related to stress and the presence of geological structures. Due to well executed de-stress blasting practices at the mine, stress related problems are minimized. However, structurally related damage mechanisms associated with shear zones, faults and joints pose a substantial hazard. Identifying active structures from the dataset of seismic and microseismic events is generally problematic. We propose a new methodology that uses a combination of spacetime event density, hierarchical clustering and principal component analysis to identify planes of microseismic activity, termed active planes (APs). Once identified, the presence and intersection of active planes can be used to provide a hazard ranking for nearby excavations. The ranking is based on the standard Q rock mass classification system, with emphasis on the joint set number (Jn) and stress reduction factor (SRF) parameters. If the rock is treated as a fractured continuum, then, the Jn indicates the degree of freedom for blocks to move and hence, increased potential hazard. An increased hazard can also result if the APs are larger-scale and discrete (faults) rather than ubiquitous (joints). In this case the SRF is used as a measure of the degree of looseness in the rock mass.

May 1, 2004

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By B. Comley, M. C. Harris

There is as yet no accepted method of predicting flotation frother performance in plant processes based on laboratory scale characterisation techniques. This paper investigates the use of dynamic surface tension, using the maximum bubble pressure method, as a means of evaluating frothers and frother mixtures. An adsorption model is presented, which has been used to quantify the role of frother type and concentration during frother bubble interaction, based on the correlation of model parameters to physical frother characteristics. This approach was found to provide useful insight with respect to blending and selection of flotation frothers to meet specified flotation performance criteria.

Jan 1, 2001

By Philip W. Holland

This Bureau of Mines report discusses the results of three independent reconnaissance geochemical surveys conducted in the vicinity of the Bush Dome reservoir in the Bureau-owned Cliffside field near Amarillo, Tex. The surveys consisted of (1) determining the helium content of area ground waters, (2) determining the helium content of area soil gases and ground waters, and (3) determining the helium content of soil gases collected on a grid sampling pat- tern in the Cliffside field area. The native natural gas in the Cliffside field contains about 1.8 percent helium. To date, approximately 54 billion cubic feet of gas containing approximately 39 billion cubic feet of helium has been injected into the center of the Bush Dome structure. The research work, which was completed under contracts, was done to determine if helium concentration levels in ground water and soil gas could he used as an indication of the presence of helium in a subsurface natural gas accumulation. Results of the surveys were positive in that helium-in-water and helium-in- soil-gas anomalies were detected in portions of the Cliffside field area. All helium analyses were performed by mass spectrometric techniques.

Jan 1, 1979

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By T. Warren, R. Pender

"Significant strides have been made during the past decade to integrate the traditionally separate administrative functions of financial management, materials management and maintenance management.In 1983, Key Lake Mining Corporation (KLMC) brought on-stream one of the most technologically advanced mining operations in North America. There was a requirement to support this new facility with state-of-the-art management information systems.This paper will discuss the development and evolution of the corporation's computerized information systems with specific emphasis on the utilization of computer systems to assist maintenance personnel in performing their work activities:Note: In August of 1989, the administration and operation of the Key Lake Mine was assumed by CAMECO - A Canadian Mining and Energy Corporation.IntroductionThe Key Lake Mining Corporation was incorporated in 1979 and operates a $500 million uranium mining and milling complex located in northern Saskatchewan.The feasibility study and environmental impact statements for the Key Lake Mine were submitted in 1979and in August of 1981, following a public inquiry, approval to proceed with construction was granted. Ore processing commenced in October of 1983 and during 1984 a total of 10.4 million pounds of uranium oxide (U3O8) was produced. In 1987, an annual production of 13.5 million pounds was achieved clearly establishing Key Lake Mining Corporation as the world's leading producer of uranium oxide. Current ore resources are expected to extend production of the Key Lake facility into the year 2000."

Jan 1, 1990

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

The major proportion of South African coal is extracted by the bord-and-pillar mining method which requires that the overlying strata be supported by pillars of coal. The stability of the pillars is a major safety concern. One of the factors which affects the strength of coal pillars is the intensity and nature of discontinuities in the coal seams. Current design methods for pillars assume that al the coal seams have equal strength and are equally disturbed by natural discontinuities, resulting in over-designed pillars in some cases and potentially unstable pillars in others. Research was carried out to determine the nature of discontinuities in coal seams and to assess their potential effect on pillar strength. It was found that large variations exist in the intensity of discontinuities in the different coal seams being mined. In addition, numerical model studies showed that the discontinuities could significantly reduce pillar strength if the width-to-height ratio of the pillars is small, but the effect decreases as the width-to-height ratio increases.

Jan 1, 1997

By M. P. Brungs, S. Haji Amini

Static dissolution of CaO into a CaO-SiO2-Al2O3slag and slags with additional fluxing agents (fluorspar, nepheline syenite and ilmenite) was studied. The slag was packed into dense CaO crucibles and heated to 1500ºC /1600ºC. After reaction, the crucible was air cooled and cross-sectioned. The development of the Ca2SiO4 phase and concentration profiles of various cations across the reaction zone were examined by Electron Probe Micro Analysis. At 1500ºC, a Ca2SiO4layer was found to form at the CaO/slag interface. No such layer was evident at 1600ºC. Ilmenite and nepheline syenite were found to be effective substitutes for fluorspar, increasing the rate of CaO dissolution.

Jan 1, 2004

Disclaimer ?You may hear something today that surprises you. If you are pregnant or have a heart condition, you may elect to stop hearing now. ?Some of what you are about to hear you may already know. ?Much of what you are about to hear and see is information that is from and can be found via other sources. ?If any of my statements during the course of this presentation are thought or found to be incorrect, I am not responsible for these comments.

Jan 1, 2006

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980

The Ministry of Commerce has been carrying out an evaluation of the resources of the Northwest Nelson region. In part this was to revisit the issues covered in the earlier proposal to close part of Northwest Nelson to mining under section 24 of the Mining Act (1971) initiated in 1990. In addition, the option of using GIS to integrate a variety of spatial data sets to aid policy formulation could be tested. The Northwest Nelson assessment would be a useful trial. The subsequent national park proposal provided a major impetus to the project and resulted in the scope of the study being broadened to include all energy and minerals resources.

Jan 1, 1993

By A. Burger Pintér

To be meaningful the sharing of ideas about the National Environmental Management Act (NEMA) and social issues within the context of Mining and Metallurgy (M&M) requires an honest scrutiny of the M&M/social environment relationship, both past and present. It is not a secret that this relationship has been and is fraught with difficulties. Thus from all perspectives (M&M, society and environmental and social consultants) such a dissection, that highlights the realities, both good and bad, is uncomfortable. For this section of the colloquium to have any value, the honest but difficult approach needs to be taken.

Jan 1, 2000

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By W. J. Theron

The purpose of the paper is to give an introduction to the concept of fatigue and its causes in the mining industry. By knowing the fundamental role it plays, together with its dynamics, can positively contribute to a mine?s safety management system. The difference between physical and psychological fatigue will be addressed with a possible range of causes that could trigger fatigue. There are two main sources of fatigue: firstly, work-related fatigue which is associated with activities at the workplace; and secondly non-work-related fatigue. The shared responsibility between the employer and employee is also discussed as it involves factors that occur both in and outside the workplace. Employers have the responsibility to manage fatigue through using a risk management approach. Employees have the responsibility to ensure they get enough sleep, take sufficient and regular nutrition, are healthy and physically fit and come to work fresh and alert. The impact of the implementation of a fatigue management plan and procedures has the potential to eliminate employee fatigue or its causes, reduce the likelihood of fatigue occurring in the workplace, and counteract the effects of fatigue when it occurs. Factors considered when implementing a fatigue management system include: extended hours of work, shift work, time of day and work design. Fatigue is one of the major role players (either causal or contributory) when it comes to causes of fatalities in the mining industry. Our main challenge in identifying whether fatigue played a role is the fact that it cannot be tested in post-mortems like drug or alcohol abuse. It is an aspect worth understanding and getting an organization sensitive to managing it properly to benefit both organizational as well as employee needs. Keywords Signs of fatigue: Causes of fatigue, circadian rhythms, the fatigue equation, fatigue management, fatigue affecting safety, fatigue fighting tips, lifestyle suggestions.

Jan 1, 2011

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

By B. D. Paphane

Since the commissioning of the Tati Hydrometallurgical Demonstration Plant (HDP), which produces Ni and Cu cathodes as well as Co salt from sulphide concentrate employing Activox® technology for leaching, no kinetic data has been generated from the plant under normal operating conditions, from start-up to steady state. Therefore, this study seeks to determine the rate of reactions in the leaching circuit with a view to obtaining kinetic data for the system under the current operating conditions. Within the five-compartment autoclave operating at temperatures of 105°C to 110°C and 1100 kPa pressure, the extraction of Ni, Cu, and Co ions into solution is achieved through the oxidation of the sulphide concentrate using approximately 50 kg H2SO4 per ton, 10 kg NaCl per ton, and 1.21 kg O2 per kilogram of S2-. The autoclave reactions showed complex kinetics, with the reactions proceeding via some intermediate(s) before the formation of products. The results suggest that the reactions were dependent on the size of the metal ion of interest and the concentrations of the metal ions in the Tati concentrate as well as in chloride leaching. The order of the leaching rate constants was Fe2+ > Cu2+ > Ni2+ > Co2+ in all the compartments studied. The rates of leaching were also found to decrease as the concentrate moves from compartment 1 to compartment 4. For compartments 1 to 3, leaching was observed to be preceded by dilution of the repulp liquor (copper raffinate). The leaching rate for compartment 5 was slightly lower than that of compartment 1 but higher than the rates of compartments 2, 3, and 4 for all the metals studied. Keywords kinetics, hydrometallurgical plant, Activox

Jun 1, 2013