Search Documents

By I F. Bell, K P. Hammerschmid

Well planned and executed environmental management plans can reduce life-of-mine operating costs and the need to deal with major environmental issues at the time of mine closure. With proper planning during the exploration, feasibility and execution phases of a project, final closure costs can be reduced. The reduction of closure costs should be considered during exploration and initial feasibility studies and when process facilities, waste rock dumps and tailings impoundments are designed. During the mining of the resource, closure cost reduction will depend on effective and efficient environmental management plans for ongoing land clearance, segregation of mine waste materials, management of mine site water and workshop wastewaters, and the establishment of progressive rehabilitation strategies. These issues are the responsibility of planning, production, technical support and maintenance personnel at an operating site. The successful implementation of environmental plans will ensure that all impacts are reduced and that closure issues with major cost implications are addressed prior to closure of the mine.

Jan 1, 1995

The early history of the mine is traced from the beginning of shaft sinking in 1886 to the purchase by the Broken Hill Proprietary Co. Ltd. in 1949. A necessary preliminary to mechanisation of the Borehole Seam was development of the Young Wallsend seam, andthis development is described. Surface reorganisation and coal handling arrangements are dealt with in detail. Then follows a description of the Borehole Seam mechanisation, the provision of power supply for this purpose, arid pumping arrangements in themine.INTRODUCTIONStockton Borehole Colliery is in the Parish of Teralba, between the townships of Teralba and Boolaroo, and about 12 miles from Newcastle. The colliery holding, a freehofd area of 2,560 acres, was apparently an original land grant when acquired by Teralba Co-operative Coal Company who decided to mine for coal and named the mine "Teralba Colliery." Shaft sinking was commenced in 1886 but was delayed by financial and water troubles to such an extent that it was not until 1901 that the Borehole Seam was reached.Coal was won until 1904 using a single 16 ft. diameter shaft, ventilation being achieved by means of a wooden boxing down one side of the shaft. This collapsed, and operations ceased until the mine was taken over in 1906 by a company known as "Borehole Colliery Limited," the principal stockholder being the Stockton Coal Company. It renamed the mine "Borehole Colliery." This new company immediately commenced sinking a 13 ft. diameter air shaft. In 1908 the Stocktol1 Colliery at Stockton was abandoned, and during the following year much of its equipment was transferred to Borehole Colliery. The name was again changed becoming "Stockton Borehole Colliery." From this period on, coal was produced from the Borehole Seam by...

Jan 1, 1957

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida and Western phosphate process tailings. Physical, mineralogical, and surface characteristics were determined for both types of samples. The flocculation tests investigated dispersant and flocculant types and doses, pH, and slurry percent solids, while other parameters were held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. In single-stage tests, flocculants having low to medium anionic character effectively upgraded products at moderately elevated pH. Multiple-stage tests, and tests in which flocculants of lower molecular weight were used as site-blockers, gave improved results.

Jan 1, 2002

By AMIRA P588 Research Team

This contribution summarises new knowledge and data, obtained during a three year ARCAMIRA funded research project, on the mineralogical and geochemical characteristics of hydrothermal alteration associated with low sulfidation, gold-silver epithermal deposits. These data are used to develop exploration vectors for use at both deposit and district scales, plus techniques have been established to distinguish ore grade epithermal systems from barren or low grade systems. Deposits investigated were Ladolam, Papua New Guinea, Gosowong and Mt Muro, Indonesia, Cerro Vaguardia, Argentina and Bimurra and Twin Hills, Australia.

Jan 1, 2005

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By Martin Williams

During the coming decade, many of the first generation of ‘super-pit’ gold and base metal mining operations in North and Latin America will reach the end of their economic lives. The closure of such pits in a manner which is environmentally sustainable presents a considerable challenge to the minerals industry. Pit closure often results in the partial or total inundation of formerly dewatered mining operations, and the resultant formation of lakes. The development of techniques for predicting, and controlling, the chemistry, groundwater discharge characteristics and long term hydrospheric impact of these lakes has become a critical aspect of pit closure planning. In this sense, the paper point out that Sleeper Mine was the first of a new generation of open pit gold mines developed in Nevada, USA. The closure of the Sleeper pit exemplifies the use of a range of pragmatic approaches to pit flooding, with applicability to mine closure at many other sites throughout the Américas.

Apr 22, 2003

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize productivity, the influence of reclamation parameters must be well understood ? which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass appraisals, and also the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, we use biomass production experimental plots on reclaimed mine sites established by the Powell River Project (PRP) for a comparative study between satellite measurements of Normalized Difference Vegetation Index and inventory estimates of biomass under a variety of conditions. The PRP is a unique public-private partnership in the coalfields of southwestern Virginia dedicated to enhancing beneficial use and environmental protection of mined lands.

Feb 27, 2013

By J. Châteauneuf, R. Dupéré, D. Mrabet

"In gold processing plants, it is common to start gold cyanidation in the grinding circuit by simple cyanide addition or as a result of recycling residual cyanide. In such cases, advantages such as a decrease in gold lockup and reduced leach time have been noticed. The prevailing conditions in grinding circuits such as intense mixing, particle breakage and friction or high temperature are quite different from those found in tanks and so is the resulting cyanidation behaviour. To gain a better understanding of the cyanidation behaviour in mills and of the pertinence of cyanide addition in grinding circuits, lab tests were conducted using an industrial ore from Canadian Malartic mine. In this study, the effects of different parameters on cyanidation in grinding circuits were examined; parameters such as such as temperature, dissolved oxygen, cyanide concentration and pH. The results showed that the kinetic benefits of high temperature in the mill can overcome the low dissolved oxygen concentration thus leading to an overall gold dissolution kinetics improvement for temperatures up to 50°C. However, gold leach in the studied grinding circuit at lab scale caused an increase in cyanide consumption with a higher generation of iron cyanide and SCN-. These results were confirmed by tests in the Canadian Malartic plant where the cyanide addition was moved from the SAG mill to the leaching tanks resulting in a 20% savings in cyanide consumption.IntroductionCyanidation in grinding circuits can benefit gold processing by decreasing gold lockup and by reducing leach time. However, other aspects regarding gold and cyanicide dissolution come into play in the conditions prevailing in grinding circuits. Indeed, high turbulence, high temperature, recycling load, friction and particle breakage make cyanidation behaviour in grinding circuits different from in-tank cyanidation (Marsden and House, 2006). In several cases, cyanide in grinding is limited to a very low level or completely avoided such as in circuits with gravimetric separation, for ores requiring oxidative pretreatment or for preg-robbing ores. In other cases, water management imposes a certain recycling of residual cyanide. This problem is generally addressed by a case-by-case approach. However, the chemistry of cyanidation in mill circuits is worth investigating in order to assess the advantages and disadvantages."

Jan 1, 2016

By J. M. Ortiz

Mineral resource evaluation requires defining geological domains that differentiate the types of mineralogy, alteration and lithology. Usual practice is to consider the domain boundaries as hard, i.e. data from across the boundaries are disregarded when estimating the grades within a given domain. This practice may hinder the quality of the estimates when a significant spatial correlation of the grades exists across the domain boundaries. In this paper, several geostatistical methodologies to handle soft geological boundaries are compared through a case study on a copper mine in Chile. The estimation methods considered are: ordinary kriging using hard boundaries between geological domains; ordinary kriging omitting the geological boundaries; traditional and standardized ordinary cokriging of the grades assayed in different domains; ordinary kriging within dilated geological domains, that is, incorporating samples from adjacent domains up to a given radius from the boundary of the domain being considered. The estimations are performed using a set of exploration data (drill hole samples) and are validated using a set of production data (blast hole samples collected for grade control). Results indicate that kriging with dilated domains performs better than ordinary kriging using hard boundaries or no boundaries and better than the ordinary cokriging approaches. It therefore appears as a simple alternative to global kriging (without considering the geological domains) and allows accounting for changes in the grade average, dispersion and spatial continuity with the geological characteristics of the deposit, via the use of grade variograms proper to each geological domain. The maximal distance for searching samples from adjacent domains should be chosen according to the spatial correlation of the grades across the domain boundaries, or via a cross-validation at an early stage of the mine or a jack-knife if production data are available. Keywords: Kriging; cokriging; soft boundaries; hard boundaries; geological control; geological domains.

Jan 1, 2006

By N. R. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract No. J0395028, "Noise Control of Rubber-Tired Front-End Loaders Used in Surface Mining. " Two loaders, a Caterpillar 988 and an International H-400B, were chosen for this program, and the noise sources and acoustic paths that contribute to the operator's noise exposure were identified. Retrofit noise control treatments were designed and installed on these loaders, and noise reductions of more than 10 dBA at the operator position were achieved on both machines. The retrofit packages are low cost and have been field tested in two mines for more than two years. The results of the program were communicated to the mining industry through a series of noise control workshops and a field manual. The workshops were given in nine states across the U.S. and more than 440 manuals were distributed An audio/visual slide presentation was also developed which the program.

Jan 1, 1983

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

Sulphide minerals, such as pyrite and sphalerite, are leached by ferric sulphate. This reaction produces ferrous sulphate and other dissolved products. The ferrous sulphate is re-oxidized to ferric sulphate by bacteria. These reactions can be written as: [ ] However, in 1964 Silverman and Ehrlich proposed that this is not the only role that is played by bacteria. These researchers proposed that T. ferrooxidans enhances the rate of oxidation of pyrite above that achieved by chemical reaction with ferric sulphate at the same solution conditions. This enhancement in the rate of dissolution was proposed to occur by direct microbiological action, possibly by the extra cellular secretion of an enzymatic oxidant. Since the Silverman and Ehrlich proposal, different authors have made opposing claims concerning the action of T. ferrooxidanson pyrite. This ?direct mechanism? of bacterial dissolution of pyrite can be given by the following reaction: [ ]

Jan 1, 2000

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By G. Konak

In-pit crusher location selection has had an important role recently, since increasing diesel prices. One way of reducing the haulage costs is to shorten the truck haulage distance by bringing the truck dump point into the pit. This study covers the work done on the optimum crusher location definition for a company that produces aggregate near Izmir, a city of Turkey located in the west. This paper will discuss the effects of pit geometry and mine access requirements on optimum crusher location selection that are mainly based on the establishment of minimum haulage distance. The method will be introduced first and then the computer algorithm developed for this study will be discussed later in the paper. Keywords: in-pit crushing, optimum location selection, optimizing haulage, computer aided design.

Jan 1, 2007

By A A. Ndiaye, A Galli

In a companion paper on current hedging practices in the mining industry (Armstrong et al, 2009) we showed that contrary to popular belief, mining groups are still using financial derivatives to hedge against foreign exchange risk and interest rate risk, and more recently against adverse changes in energy prices, notably the oil price. This paper presents a case study on a hypothetical gold mine to illustrate the impact that hedging policies could have on its profitability by reducing the downside risk due to adverse changes in the exchange rate and increases in fuel prices. The characteristics of the hypothetical mine have been set to reproduce those of a real gold deposit, the Kisladag mine that is currently being exploited by open pit methods in Turkey. This mine was selected because its feasibility study was available to the public. Geostatistical simulations are used to reproduce the inherent uncertainty on the recoverable reserves û stochastic simulations are used to generate the variability of the other three key sources of uncertainty: the gold price, the cost of energy and the exchange rate. A simple strategy based on straightforward vanilla options (puts and calls) was developed for hedging the last two risks, on the assumption that the company sells its production at the prevailing spot price.

Jan 1, 2009

By W. C. Maurer

A study of the mechanics of shear failure of rock under pressure has been made. The transition from brittle to ductile failure occurs when the friction along the fracture surfaces exceeds the shear strength of the rock. A machine has been developed for measuring both the shear strength of rock and the friction along rock fracture surfaces. In this shear machine, the fractures are forced along definite planes; as a result, the rock is stronger than in compression tests where the fractures choose the weakest paths through the specimens. Friction is composed of several forces: (1) the forces to slide irregulurities on surfaces over each other; (2) forces to shear some of these irregularities; (3) molecular attractions across the fractures; and (4) forces required to break bonds resulting from melting and welding at the tips of irregularities on the surfaces. Friction along rock fracture surfaces is not proportional to contact pressure as usually assumed; instead, it increases as the contact pressure raised to the 0.4 to 0.8 power. INTRODUCTION It is difficult to produce tensile stresses under the high compressive stresses present in the earth; therefore, in deep drilling and geological faulting, shear failure predominates. This shear failure mechanism is complicated because rock is a heterogeneous material containing pore spaces, microfractures, elastic discontinuities and other imperfections. A study of shear failure of rock under pressure has been made to obtain a better understanding of this complex mechanism. A machine has been developed and used to measure the shear strength of rock and friction along sheared surfaces. This machine has certain advantages over the compression test — shear properties can be measured under low normal stresses and shear stress and normal stress can be varied independently. The first part of this paper is a description of shear failure of rock under pressure. The role of shear strength and friction along fracture surfaces in the shear failure mechanism will be discussed. The second part consists of a description of the shear machine and a discussion of the shear strength and friction data obtained using this machine. It will be shown that shear strength depends upon the size of the stressed zone, and that friction does not increase linearly with contact pressure as usually assumed. Attempts are made to relate some of the new concepts to tectonic failure and to dril ling. SHEAR FAILURE IN ROCK TRIAXIAL TESTS The shear failure mechanism is illustrated by the triaxial test shown in Fig. 1. In this test, a cylindrical rock specimen is subjected to a confining pressure, PC, and an axial pressure, pa. These external pressures produce normal a and shear T stresses on inclined planes within the specimen equal to1 where 0 is the angle between the specimen axis and a normal to the inclined plane. Fig. 2 shows how triaxial specimens deform as the axial pressure is increased. The pressure is

Jan 1, 1966

By Marc C. Bétournay

Under the requirement to define the economic advantages of using hydrogen fuelcell vehicles, a broadscoped project was initiated to quantify the costs associated with operating fuelcell vehicles and diesel vehicles. While ventilation savings are clearly an advantage for the former, a complete and detailed analysis of this and other operational and capital cost elements was undertaken in order to provide the mining industry with factual information in considering the changeover from one technology to another. This article outlines the results of the investigations to date defining the costs/benefits associated with: capital purchases, operations (electrical/diesel, mine air heating fuel, ventilation, openings, surface and underground infrastructure, maintenance, labour, etc.), delivery of energy, regulatory obligations, and mine production. Considerations are given to the type and size of a mining operation, the depth, and location in North America. Significant ventilation power, equipment and infrastructure savings are possible with the application of fuelcells for shallower mine applications. At depth, where heat is an issue, there is a reduction in benefit. Specific qualifiers such as minimum air velocities, dust dilution, shaft and heating system velocity limits must be considered on an individual mine basis. While the capital cost for fuelcell mining equipment is currently higher than diesel versions, the high cost of fuelcells is anticipated to be reduced significantly in the near future with the intensification of manufacturing. In either case the operational savings would probably be sufficient to balance the supplementary capitalization costs. A comprehensive cost-benefit report will be issued in the near future.

May 1, 2003

By James Diekmann

The Disputes Potential Index (DPI) is a computer program designed to help team mem¬bers assess the likelihood of contract disputes on a construction project. The program's predictions are based on data from 159 construction projects that encompass a variety of public and private projects. The impact of three categories of project characteristics are included in the DPI program, specifically, people, process and project characteristics. Ultimately, DPI returns an overall project score that indicates the likelihood of exces¬sive contract disputes. The output of a DPI analysis can be used as part of a contract readiness review or to define the need for extraordinary dispute avoidance procedures. This paper examines the development of DPI and presents the results of DPI analyses on several tunneling projects.

Jan 1, 1995

By M. Leslar

Slope monitoring has been an important issue in static terrestrial lidar for some time. Several solutions for monitoring the progress of a slide have been devised over the years. All of these solutions have required users to be in the field operating the lidar equipment. This paper presents a new system developed using the Optech ILRIS-HD or ILRIS-LR lidar and the scripting language of PolyWorks to produce an autonomous slope monitoring system. This system has proven invaluable in detecting and alerting mine workers to potential danger within their mine sites. It has already been deployed in two mine sites and is scheduled to be installed at a third.

Feb 27, 2013