Search Documents

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

By P Rowe

New Zealand Steel's Taharoa titano-magnetite mine, south of Auckland, set two national load records when it transported around 2000 t of mining equipment three kilometres overland on time, under budget and without safety incident. It was the first time in New Zealand that four platform trailers were assembled end-to-end to transport a load. It was also the first time that a single load of 1000 t was transported on platform trailers. The need for the relocation of all equipment was realized five years ago. It took two years of planning and specialist advice to relocate the mine's 250 t dredge, 500 t surge bin, 1000 t concentrator plant and ancillary equipment from the Southern Mining Region across a specially designed haul road to the Central Mining Region. The project was carried out during a six-week shutdown in early 2001. Two dry docks were constructed, one at each end of the relocation route. The equipment was floated into a dismantling pond that was interconnected with the dry dock in the Southern Region. Through pumping, the water levels were controlled to allow transfer of the separated units from the dismantling pond into the dry dock. Once drained, sets of self-elevating platform trailers were used to transport the main units, one at a time, between the dry docks. Five prime movers were used to pull the loads. At the receiving end, the units were off-loaded in a dry dock interlinked with ,the first mining pond. The equipment was relocated because the reserves in the Southern Mining Region were mined out. A natural watercourse û the Wainui Stream û defines the northern boundary of the Southern Region and the objective became to relocate the mining plant to the other side of the stream and re-establish in the Central Region. The project team selected the trailers as the most effective means of transporting the equipment, particularly given the non-invasive means of crossing the Wainui Stream. Negotiations with prime contractor Tranzcarr Heavy Haulage Ltd commenced in mid-2000. The remainder of 2000 was spent in developing concepts with the contractor, detailed designing, preparing the dry docks, haul road and initial mine plan for the Central Region. These activities occurred with no conflict to the normal site production.

Jan 1, 2001

By Rapheal Trousselle

For over 5 years, Davey Bickford has been developing and testing an electronic detonator blasting system. These new-technology detonators provide more accurate timing than conventional systems that rely on the combustion speed of a pyrotechnic composition.

Jan 1, 1997

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

By Clark F. Grain

These investigations were undertaken as part of the Bureau of Mines program for the development and evaluation of high temperature nonmetallic materials. This report consists of thermal expansion and phase inversion measurements by high-temperature X-ray diffractometry on the principal oxides of beryllium (BeO), calcium (CaO), titanium (TiO2 ), zirconium (ZrO2 ), hafnium (HfO2), and thorium (ThO2); all were high-purity commercially available oxides. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures. Expansion was determined parallel to each major crystallographic axis for the anisotropic oxides: BeO, TOi2, ZrC2, and HfO2. Combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C. and approximately 2 percent at 1,000° C. No hysteresis in the expansion curves was noted between heating and cooling cycles. The Bureau's values were compared with published expansion measurements obtained by X-ray diffraction, dilatometric, interferometric, and telemicroscopic techniques. For anisotropic oxides, average linear expansion values were calculated from the volume expansion.

Jan 1, 1962

By Paul H. Lu

This Bureau of Mines report summarizes the analysis and eveluation of the field measurement results of a comprehensive ground control study conducted in a mechanized longwall coal mine in West Virginia. Emphasis is placed on the three basic ground control parameters: ground pressure, ground movement, and geomechanical properties. Specific topics include premining ground pressures, front-abutment pressure in the longwall panel, histories of pillar loading, differential roof-strata movement and bed separation, differential floor strata movement, entry roof-to-floor convergence, in situ moduli of rigidity of coal seam and roof and floor strata, and mechanical properties of coal and coal measures rocks.

Jan 1, 1985

By N. Seidle

Numerous studies conducted in the 1960's and 1970's concluded or implied (1) that a high accident rate in terms of severity and frequency exists among new (first year) operators of mine machinery equipment, and (2) that lack of experience and training is a major cause of this high accident rate. Further studies refined this premise to show that the major causes of accidents among first year operators are: (1) lack of manipulative skills; (2) failure to follow/adhere to routine procedures; and (3) failure to recognize and respond properly to hazards. This report describes the design, development, and manufacture of a shuttle car operator training system, including a program of instruction which: ? Is economically feasible. ? Addresses accident data and specific causes of accidents. ? Includes an aerospace quality simulator of sufficient fidelity to teach and develop manipulative skills, recognition of and response to hazards, and routine and emergency procedures. ? Is designed to significantly reduce the severity and frequency of accidents especially during the operator's first year. ? Is designed to significantly improve the performance of the trainee as compared to the standard learning curve. Development of the simulator produced several valuable by-products including a major state-of-the-art technological advance in visual systems for simulators, and a first-time application of (certain) advanced filming techniques to underground filming.

Jan 1, 1984

By P Cameron

MetPlant conferences have focused on ensuring mining projects are well designed then optimised to operate safely and effectively at the top end of world’s best practice to ensure shareholders are not just happy but delighted. This assumes the MetPlant was built right the first time. However, reality is, too often Plant Metallurgists (PlantMets) find after commissioning they are faced with the expensive task of correcting errors or modifying shortcomings to achieve product quality at name-plate capacity, i.e. get it right the second time. Why do companies spend good money to engineer an excellent feasibility study then allow “wise men” remote from the project team to impose cuts in budget and schedule, often under the guise of value engineering? Since mining is full of uncertainties, such actions can increase the risks of failure with the result that some MetPlants do not work well. Can PlantMets influence the remote wise men who often are also imposing the rules for lending and the required returns to appreciate the uncertainties of mining and their associated risks then let the project team get it right the first time? PlantMets can negotiate with the wise men from the outset of the project and bring them into an outer layer of the team where they can understand the risks then share responsibility and accountability to achieve the common goal of building a MetPlant which works well the first time and deliver the forecast profits. Since shareholders are not in the business to make losses they appoint a Board of Directors to deliver the best outcomes for the shareholders. Thus the Board should seek effective advice on the risk reward implications from the PlantMet before making their decisions.CITATION:Cameron, P, 2015. Do all metplants work well? PlantMets can ensure they do, in Proceedings MetPlant 2015, pp 2–9 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Wu Xueling

9K medium was used to isolate iron-oxidizing bacteria from 27 sump water samples collected from Dexing Cop-per Mine, Chengmen Mountain Mine and Yin Mountain Mine, Jiangxi Province, China. Lead acetate and silver nitrate were used to enrich metal-resistant iron-oxidizing bacteria from the above water samples. Isolate 16 was isolated from the sample taken at Dexing Copper Mine. Growth experiments indicated that when incubated under lead acetate (3,500 mg/L), isolate 16 still carried out ferrous ion oxidation, while isolate H1, a less resistant strain taken at Yin Mountain Mine, had a tolerance level of only 400 mg/L. When assayed with other metals, i.e., Ag+ (240 mg/L), Hg2+ (0.9 mg/L), Cu2+ (32,000 mg/L) and Mg2+ (22,500 mg/L), isolate 16 still carried out ferrous ion oxidation while, on the other hand, isolate H1 exhibited much lower tolerance levels, i.e., Ag+ (60 mg/L), Hg2+ (0.1 mg/L), Cu2+ (19,000 mg/L) and Mg2+ (13,500 mg/L). Based on 16S rDNA sequence data, isolate 16 and H1 were both identified as Acidithiobacillus ferrooxidans.

Jan 1, 2007

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987

By Eric E. Cather

A mineral survey of the Fisher Gulch RARE II area (A5299), Trinity County, California was conducted by the U.S. Bureau of Mines and U.S. Geological Survey. The Bureau of Mines was responsible for detailed examination of mines, prospects, and mineralized zones; the Geological Survey conducted geological, geochemical, and geophysical studies of the area. The area is underlain by the Salmon Hornblende Schist. Tonalite stocks 1.5 mi (2.8 km) to the east and northeast of the area intrude the schist and are closely associated with the nearby nines (Cox, 1967). The mines have quartz veins containing sulfides and gold in shears trending east to north past in the schist and tonalite (Hotz, 1972). Strewn and terrace gravel s occupy most of the drainages, many have yielded substantial quantities of gold.

Jan 1, 1981

By G. W. Jones

As a part of its general safety program the Bureau of Mines has investigated various means useful for the elimination or mitigation of the explosion hazards in connection with combustible gases incident to the mining industry. Information has been obtained relative to the explosibility of numerous simple and complex gaseous combustible atmospheres. Although experiments along this line have pertained largely to combustible gases in the mining and allied industry, considerable information has been obtained relative to the explosive hazards of combustible gases and vapors used as anesthetics.

Jan 1, 1939

By Mina M. Shinouda

Brightwater West (BT4) represents the state of the art in utility tunneling, namely a long relatively small diameter, soft ground tunnel, with no intermediate shafts, under significant groundwater pressures, requiring very precise survey control in order to hit a small exit window. The tunnel is over 6.4 km (4 miles) in length, is expected to encounter active earth pressures of over 5 bars in glacial geology, and a planned hole through into a shaft eye constructed at 45.7 meter (150 feet) below the water table. Despite the fact that all of these challenges have been previously overcome in larger diameter tunnels, the technical solutions are much more challenging in a smaller diameter due to the lack of space available for implementing the equipment and techniques required. In addition to the technical challenges, the project is faced with many of the constraints designed to minimize the impact of these types of projects on the neighboring community and environment. The work shaft for BT4 is within 15.2 m (50 feet) of Puget Sound and is on a site that was previously occupied by petroleum storage tanks, and all of the tunnel muck has to be removed from the site by barge as trucking is not allowed by contract. The paper addresses the work performed during the preparation for tunneling stage of this project both in assembling the TBM and in preparing the site for its arrival.

By Dennis J. Riley

A. This outline addresses what a sub-contractor, or a subsub-contractor should do to get paid in the event the general contractor or building owner files for bankruptcy. B. Negotiating payment terms. Progress payments vs. "pay when paid". How a sub or subsub can avoid financing the contract. C. Court interpretation of "pay when paid" clauses allow postponement not excusal of payment. See, e.g., Seal Tite Corporation v. Ehret. Inc., 589 F. Supp. 701 (D.N.J. 1984) (where the court held that the general contractor could not delay payment indefinitely to the subcontractor in the event of non-payment from the owner); United Plate Glass Co. v. Metal Industries. Inc., 525 A.2d 468 (Commw. Ct. Pa. 1987) (where the court held that payment from owner was not a condition precedent to paying subcontractor but instead a timing mechanism indicating when payment should be made); But see. Straham v. Landis Construction Co., 499 So. 2d 417 (La. App. 4 Cir. 1986) (where the court strictly interpreted the "pay when paid" clause).

Jan 1, 1991

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

1. ACKERMAN, C. L. The Binary System Manganese-Zinc. Ztschr. Metall., vol. 19, 1927, p. 200. 2. ADKENASY, P., AND KLONOWSKY, S. Über die Manganatschmelze. Ztschr. Elektrochem., vol. 16, 1910, p. 107. 3. AKTIEBOLAGET FERROLEGERINGAR (assignees). Method for the Manufacture of Manganese Alloys Poor in Carbon or Silicon or Else Manganese. British Patent 163262, Apr. 28, 1921; U. S. Patent 1480267, Jan. 8, 1924. 4. Method of Producing Manganese or Manganese Alloys Poor in Carbon or Silicon. British Patent 174923, Jan. 25, 1922.

Jan 1, 1934

By Robert J. F. Goodfellow, William A. T. Meakin, Kevin Clarke, Eric Cole

INTRODUCTION New York City Water Supply—Background and History Since the 1840s New York City has been developing the largest, and perhaps, the best urban water supply and distribution system in the world in terms of quality and reliability. One of the engineering marvels of the modern world, the New York City water supply and distribution system serves a population of almost nine million, including residents in nearby Westchester, Putnam, Ulster, and Orange Counties of New York State. The average daily supplies presently are running at almost 60 m3/sec(about 1,350 million gallons per day). The watershed for the New York City water supply system, under the jurisdiction of the New York City Department of Environmental Protection (NYCDEP), consists of19 reservoirs and three controlled lakes, and covers an area of approximately5,000 square kilometers (about 2,000 square miles) north of New York City. The watershed total available storage capacity is about two billion cubic meters (560 billion gallons) and is divided into three reservoir systems: the Catskill and Delaware watersheds located West of the Hudson River; and the Croton watershed, located east of the Hudson River, see Figure 1. The first element of the system, the Croton Aqueduct, started operations in 1842.Through several updates and expansions, the present-day Croton system was in place by 1911, providing a potential maximum supply of about 15 m3/s (about 340 mgd). The system includes ten reservoirs and three controlled lakes. In the late 1800s, with the tremendous growth of the City, New York City water engineers began to look for additional sources. Between 1907 and 1929, the City acquired water rights and constructed a new 148 km (92 miles) Catskill aqueduct to convey water from the Ashokan Reservoir to the City. The Catskill system also included the construction of the Kensico and Hillview Reservoirs just north of the City,

Jan 1, 2005

By A. S. Macfarlane

The introduction of new technology into mining operations is seen as a strategic necessity by many mining companies, in order to improve safety and to improve operational effectiveness. Many attempts have been made in recent years to introduce new technologies into mining operations in southern Africa. Amongst these are noteworthy successes, as well as some disappointing failures. Often, the reason for failure does not lie with the technology itself, but with the work system into which the technology is introduced. Such failures may come with a significant opportunity cost, and have a detrimental effect on future development, simply because the system has not been adequately engineered, and the risks have not been adequately assessed and managed. This paper examines the reasons for such failures, and proposes a methodology to be followed to ensure successful and sustainable implementation of new technologies, such as to reduce technical and financial risk to the company, and to energize the workforce into ensuring the initial objectives of the project are met. The paper also focuses on the application of appropriate technology, and the development of technological applications which are commensurate with the level of development of the work environment into which it is introduced. The paper therefore focuses on the application of risk management, change management, systems engineering and feasibility analysis as being key elements of a successful and holistic technology implementation programme.

Jan 1, 2001

By Jewel A. G. Gomes

Electrocoagulation (EC) has been performed with Al-Fe electrode system with changing polarity for the removal of arsenic from water. The removal process has been studied using ICP-AES and Anodic Stripping Voltammetry with a wide range of arsenic concentration (1-1000 ppm) at various pH (4-10) and residence times (1-60 min). Electrochemically generated by-products have been analyzed using XRD, FTIR, XPS, SEM/EDS and Mössbauer Spectroscopy. Results revealed expected crystalline iron oxides (magnetite (Fe3O4), lepidocrocite (FeO(OH)), iron oxide (FeO)) and aluminum oxides (bayerite (Al(OH)3), diaspore (AlO(OH)), mansfieldite (AlAsO4?2(H2O)), as well as some interaction between the phases. The amorphous or ultra-fine particular phase was also found in the floc. The substitution of Fe3+ ions by Al3+ ions in the solid surface has been observed, indicating an alternative removal mechanism of arsenic in these metal hydroxides and oxyhydroxides by providing larger surface area for arsenic adsorption via retarding the crystalline formation of iron oxides.

Jan 1, 2006

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997