Search Documents

By Rainer Kahrger

During the last decade, advances were made in solvent extraction/electrowinning (SX/EW) technologies. Combined with heap leaching, these technologies made it viable to exploit large, low-grade oxide copper deposits. The El Abra Mine is a good example for such a deposit. The deposit is situated in northern Chile at an elevation of about 4,000 m (14,000ft), 70 km (45 miles) north of Calama. Codelco sold 51% of the El Abra to Cyprus Minerals in June 1994, with Codelco retaining the balance. In 1993, Cyprus and the engineer on the project began discussions withinternational companies regarding the materials-handling system requiredfor the project. These early discussions were considered critical for this fast-track project.

Jan 1, 1996

By Jesse L. Hoyer

A Bureau of Mines turbomill was evaluated for use in the production of high-purity, ultrafine x-Sic powders suitable for advanced ceramics that could substitute for high-temperature alloys containing critical materials such as chromium, cobalt, and nickel. The effect of milling param-eters, such as type of dispersant, temperature, pH, and gas environment, on the milling of x-SiC was studied. The addition of dispersants improved the grindability of x-SiC. Of the six dispersants studied, the best results were obtained with Mara-sperse N-22. Grinding efficiency was also increased when the x-SiC was milled in a basic slurry and at elevated temperature. Gas environments did not appear to affect grinding of x-SiC. Optimum grinding efficiency was obtained at 50° C in a slurry at pH 9.5 with Marasperse N-22 as the dispersant. Under these conditions, minus 100-plus 200-mesh x-SiC was ground to 80 pct less than 1 um in 4 h.

Jan 1, 1987

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By Frank Rausche

Without doubt, driven piles are the most economical deep foundation element for a nearshore environment, providing for high bearing capacities and stiffness, quick installation times, assured quality by simple monitoring and inexpensive dynamic load testing during restrike testing. However, when the pile top elevation is several meters below water surface, questions often arise as to the most reliable and economical pile installation method. Frequently encountered, yet relatively expensive, solutions include driving inside a dewatered cofferdam, driving long piles that are later cut off below water surface, or using an underwater hammer. Arguably, the most economical solution is driving the piles with a follower or chaser. However, many foundation engineers shy away from this solution because of the uncertainty associated with the transfer of energy through the interface between follower and pile, the associated potential driveability problems and maybe the limited fatigue life of the follower. This paper will demonstrate how the driveability of a hammer-follower-pile-soil system should be analyzed prior to installation and how to model the pile-follower interface both for steel and concrete piles. As an example, results will be presented which were obtained for both steel pipe piles and precast concrete piles, driven by a single-acting diesel hammer through a steel follower for a pre-construction test pile program in Venice, Italy. While analysis of the steel pile-follower system was straightforward, for the concrete piles, the presence of a soft cushion material whose material properties changed continuously posed some difficulty. Pile Driving Analyzer® measurements and CAPWAP® analysis yielded not only realistic stresses and transferred energy values in the pile, but also reasonable model parameters for further use in a pure wave equation analysis. As a side note for clarity, the dynamic measurements and analysis results herein presented are based on the GRLWEAP and CAPWAP software. GRLWEAP is commonly used all around the world for the preparation of pile driving jobs. The program either yields a bearing graph that relates bearing capacity and pile stresses to blow count or set per blow or it predicts blow counts and pile stresses as a function of pile penetration. These results allow the contractor to estimate driving time and select an economical hammer and driving system for a safe and efficient installation. CAPWAP on the other hand is the analysis of choice once a pile has been installed and records of pile top force and velocity have been acquired during installation or during a restrike test. CAPWAP is a signal matching program which calculates for one particular impact (for example at the end of driving) the static and dynamic soil parameters. Its final results include the calculated resistance distribution, the complete stress history in the pile and also a simulated load set curve. The CAPWAP calculated dynamic soil parameters can also be used in a Refined GRLWEAP analysis to generate a calibrated bearing graph."

Jan 1, 2006

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

By Mika Muinonen

"Dewatering of nickel concentrate at the INCO Thompson integrated mine-metallurgical site takes place within the smelter plant. The eight original 60 foot diameter cable torque thickeners of which four were operational and eight Dorrco internal drum filters have been replaced with a single Outokumpu high rate thickener and a single Lasta pressure filter. The modernization has resulted in a filter cake which has a more stable and lower moisture content. Control of the entire dewatering process has been improved and costs have been reduced.Typical filter cake produced from the Dorrco filters during processing of high tonnages of Birchtree mine ore was ~20% moisture vs. ~13% moisture for concentrate produced from the Thompson mine ore. The high moistures were correlated with the amount of fine magnesium silicate gangue in the concentrate. As Birchtree ore processing rates have increased, this filter cake moisture became unacceptable because of material handling problems and the impact on furnace metallurgy. The Dorrco filters were replaced with the Lasta filter in 2003 that has consistently produced filter cake at ~11% moisture.This paper summarizes the piloting, design, installation and commissioning of the modernized dewatering circuit.INTRODUCTIONThe Thompson integrated nickel processing facility was built in 1958 and originally consisted of a mine-mill-smelter and, soon after, a refinery.Nickel concentrate is pumped from the mill as a dilute slurry directly to the smelter facility ~200 meters along an unheated pipe trestle. Originally, nickel concentrate was de-watered using up to 8 conventional 60-foot diameter thickeners and 8 internal vacuum drum filters."

Jan 1, 2006

By Chris Larsen, Ian Orford, Marilene Renaud, Mike Cooper, Lud Strah

"An AG/SAG mill was commissioned at the Brunswick Mine concentrator in October 1998. This paper discusses the original liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits. The mill liners consist of steel top hat shell liners, steel end liners, rubber grates and rubber lined pulp lifters.Lifter profile and plate thickness measurements were made on monthly shop days. Trends of wear rates were used to project when liners required replacement. Wear profile information was also used to determine where liner re-design would improve wear life or minimize scrap loss. Charge motion simulation modeling was used as a tool to assist liner design modifications.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large underground lead/zinc mine with a nominal production rate of 10,000 tonnes per day. The Brunswick concentrator commenced operation in 1964 with conventional surface crushing followed by rod and ball milling to reduce run of mine ore to the required size to feed two parallel flotation circuits. In 1998 the AG (autogenous grinding) mill was commissioned for a nominal production rate of 9,000 tonnes per day replacing two surface crushing plants, three rod mills and three primary ball mills. In May of 1999 the mining rate was increased and the service of the AG mill was changed to a SAG (semi-autogenous grinding) mill with the addition of 4 inch steel balls (4% volume). The mill operates in closed circuit with 0.66 meter horizontal cyclones to produce a ground product of 90 micron nominal size (K80).The AG/SAG mill liners are steel (Norsteel, chrome-moly steel) with rubber grates and rubber lined pulp lifters.The original liner design was based on studying other AG/SAG mills and recommendations by the liner supplier, Norcast. Design factors taken into account were total cost of lining (including material and labour), protection of mill shell and impact on operating performance."

Jan 1, 2003

Jan 1, 1967

By R. F. Chaiken

The Bureau of Mines has carried out experimental and theoretical studies with prilled and pulverized ammonium nitrate-fuel oil (AN-FO) mixtures containing varying amounts of fuel oil in an attempt to quantify the effects of stoichiometric composition, nonideal detonation behavior, and expansion volume on the production of CO, NO, and N02 fumes. Experimental fume measurements were obtained in the Bureau's large closed gallery facility (7.2 X 104 liter expansion chamber) and in the standard Crawshaw-Jones apparatus (90--liter expansion shamber) using a prepackaged charge configuration containing about 450 g of explosive.4 The theoretical calculation of toxic fumes was achieved with an equilibrium detonation code called "TIGER,," Contrary to initial expectations, the NOx (= NO + N02) fumes from the large gallery test were found to be in essential agreement with the Crawshaw-Jones results. It was also concluded that (1) "TIGER" calculations offer a good approach to the prediction of toxic fumes; (2) there is a basic problem in extrapolating laboratory measurements of CO fumes to mine conditions--this being due to postdetonation oxidation of CO to CO2; and (3) the detonation velocity decay rate of an explosive is a useful experimental parameter for correlating toxic fumes production with nonideal detonation behavior.

Jan 1, 1974

By J. P. McGee

The Bureau of Mines is doing research and development work on a coal-fired gas turbine plant initially developed by the Locomotive Development Committee, (LDC) of Bituminous Coal Research, Inc. The Bureau is redesigning the turbine blading and some of the auxiliary equipment, and is reerecting, the plant at the Morgantown (W. Va.) Coal Research Center. The present goal is a 1,500-hour run at virtually the same operating conditions used by the LDC in their final 1,100-hour test with the turbine. This will allow the Bureau to properly evaluate the new blade design. Erosion of the turbine blades (particularly the roots) by ash in the hot gases from the combustion of coal was the most serious problem in extended operation in earlier experimental work. New blades made of Stellite6 are being fabricated for the stator and rotor, and armored wear strips of titanium carbide will be inserted in the blades at the areas of probable maximum ash velocity and concentration. The trailing edges of the rotor and stator blades are being thickened and thinned, respectively, to induce the ash to travel to the casing and prevent it from returning to the base of the rotor blades. The first stage rotor and second stage stator blades are being removed to provide an annular space for maximum quantities of coal ash to centrifuge to the casing. Additional blades will be added to most of the rows in the stator to stop secondary flow of dust-laden gas toward the rotor. A contract has been awarded for fabrication of the new blades. The 1,500-hour run will be started as soon as the new blades are installed.

Jan 1, 1962

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

By J. N. Van der Merwe

Due to the approaching depletion of reserves in the Witbank Coalfield, and the fact that the Waterberg Coalfield is as yet under developed, there is increasing pressure to extend the lives of the operating coal mines in the Witbank Coalfield. One potential source of coal is the old pillars, often small and at shallow depth, that were not left with secondary extraction in mind. At face value, some of these pillars appear to be suitable for secondary mining due to their high safety factors. However, it is known that over time, these pillars have scaled and the current sizes are smaller than the as-mined dimensions. It is also known that at shallow depth, the overburden is often less likely to fail during secondary mining, resulting in high abutment loads on the unmined pillars. The paper proposes a systematic method to pre-evaluate those old pillars for the possibility of stooping. The method consists of elements of fundamental methods and newly developed technology. In essence, it revolves around using empirical methods to estimate current pillar dimensions, followed by numerical modelling to investigate the probability of progressive pillar failure and then fundamental methods to determine the limits of applicability of the numerical model.

Jan 1, 2012

Whilst the wider community is both a large consumer of mineral products and relies on mineral exports for much of the wealth which sustains it, the community generally has a poor perception of the minerals industry.   The role of professionals and The AusIMM in the "New Economy" minerals industry is reviewed. The new structure of The Institute is vital as we move forward in times of globalisation, rationalism, increasing litigation, criminalisation of risk and increased focus on corporate governance. This address looks forward to ways The AusIMM and professionals of the future are positioning themselves for these and other challenges.

Jan 1, 2001

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

By H. F. Yancey

The investigations described in this bulletin are confined to a study of the washing characteristics of bituminous coals. The major part of the work was conducted by the Bureau of Mines in cooperation with the Engineering Experiment Station of the University of Illinois and the State of Illinois Geological Survey Division between 1918 and 1924, in accordance with the provisions of an agreement between these agencies. The washing characteristics of coals from many of the important coal-producing fields of the Eastern and Central States were examined. The coals of the Pacific Northwest States and Alaska have been studied separately by McMillan and Bird of the Northwest Experiment Station of the Bureau of Mines at Seattle in cooperation with the College of Mines of the University of Washington.2 OBJECT OF INVESTIGATION The object of the investigation of coal preparation by the Bureau of Mines has been to promote the production of better prepared coal and to facilitate the correct selection and design of coal-preparation plants by obtaining as complete information as possible regarding the washability of the various types of American coals and the treatment best suited to each. In addition, some attention has been given to the development of new methods of washing coal. The work naturally divides itself into three rather distinct steps: (1) Development of a systematic method of examining and testing a coal; (2) classification of the American coals on a basis of the occurrence of the impurities associated with the coal in the beds; (3) examination of one or more representative coals of each type.

Jan 1, 1929

By P Grieve, J L. Mauk

The Central Maratoto Valley in the Coromandel Peninsula contains a sequence of veins in pervasively altered dacite + andesites of the Waipupu Formation. We recognise at least eight different vein types: (1) pyrite stringers, (2) quartz + carbonate veins, (3) crystalline quartz veins, (4) carbonate veins, (5) chlorite + carbonate veins, (6) siderite veinlets, (7) siderite + carbonate veins and (8) carbonate + pyrite veins. The overall temporal trend of the veins is from early pyrite to quartz and then to late carbonate veins. Carbonate veins and pyrite stringers both form planar and irregular veins, whereas some carbonate veins have diffuse contacts with the wall rock. Gold and base metal sulphides are associated with some of the quartz + carbonate veins. Textures within the veins reflect open space filling and multi-phase reopening. A partial record of hydrothermal activity has been preserved by vein crosscutting relationships, hydrothermal alteration minerals and fluid inclusions. Hydrothermal alteration minerals display zonation from south to north. The alteration increases from unaltered to weak propylitic alteration of andesite in the south (MVRCDC1), to sericitic alteration of andesite and dacite in the north (MVRCDC3). The alteration assemblage is dominantly sericitic, with no adularia present, drawing parallels to the Thames region where there is no adularia.

Jan 1, 1999

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By N. Kumar Kittusamy

ALTHOUGH MANYSTUDIES HAVE SHOWN an association between operating heavy construction equipment and symptoms of musculoskeletal disorders (MSDs), little research has been performed that systematically characterizes the exposure of operating engineers to ergonomic hazards. This study evaluated: 1) vibration at the seat/operator interface;2) transmissibility of vibration in the Z-axis; 3) psychophysical ratings of vibration level and vibration discomfort; and 4) postural requirements of the job. Results indicate that the digging operation had higher levels of total weighted acceleration than high- or low-idling conditions. Transmissibility data showed that the seat amplified vibration, particularly in the lower frequencies. Seats demonstrated that they may not be sufficient in protecting operators from long-term effects of vibration exposure. High positive correlation was found among subjective ratings (vibration discomfort and vibration level), but moderate positive correlation was found between subjective ratings and quantitative vibration levels. Postural evaluations revealed that the operators were required to assume awkward postures of the neck, shoulder and trunk while performing their jobs. Work-related injuries and illnesses pose a continuing threat to the health and well-being of American workers. The construction industry has been historically recognized as having higher rates of fatality, injury and illness than other industries (McVittie285+; BLS). In 1994, an estimated 218,800 lost-work-day injuries were reported in the construction industry (BLS). Construction also had the second-highest incidence rate for sprains and strains. Although the industry has made progress since then, injuries and illnesses, including MSDs, continue to because for concern.

By Calvin K. Lee

This Bureau of Mines report describes a simple fire-retardant treatment for wood. The treatment involves preheating the wood surface at high heat flux (~0.6 cal/cm2 sec) to form an in situ surface char layer (~3 mm thick) on the wood. Laboratory-scale fire tests show that the precharring technique improves the fire-resistance of virgin wood by decreasing and delaying generation of volatile gases through thermal insulation effect of the surface prechar layer.

Jan 1, 1978