Search Documents

By S. Rupprecht

"This article addresses the prevalence of poor public reporting practices of coal exploration results, coal resources and coal reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or saleable tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal — therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (ROM) and saleable coal tonnage, their associated qualities and other material and relevant information.Competent or qualified persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provided. “Companies are encouraged to provide information in their public reports, which is as comprehensive as possible (CRIRSCO, 2013).” However, too often this isn’t the case, and material matters are either not reported or inadequately disclosed.According to the South African National Standard (SANS) 10320:2014 draft document, “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the saleable coal reserve must be stated. The moisture basis of reporting shall be stated.” An example as to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are detailed in the followint paragraphs. The Kendal power station, commissioned in 1988, operates at a calorific value (CV) range of 19 to 20 MJ/ kg, an ash content between 29 and 34 percent and volatiles between 20 to 21 percent. Other power stations, such as Kriel or Hendrina, may require different qualities, such as a CV range of 22 to 23 MJ/kg, an ash content between 20 and 28 percent and volatiles between 22 to 23 percent. Thus, in terms of domestic saleable coal, it is not just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station (Chetty, 2010).” Sulfur content is another important quality with the ideal coal content having a quality of less than 1 percent sulfur."

Jul 1, 2019

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

By Bernard H. Hertlein

Transportation system structures have come under very close scrutiny in the last couple of years, largely due to the damaging effects of disasters, both natural and man-made. In the Pacific northwest and California, earthquake risk is a major concern. In the central and eastern states barge impacts on bridge piers and docks are a big worry. In all cases of bridges over water and waterside structures, scour is a primary concern. Some of the results of this scrutiny have been changes in design and construction methods, and the introduction of more testing to supplement field inspection during construction, and throughout the service life of the structure. Future construction of bridges and docks will almost certainly see a continuing growth in these practices. Where foundations are concerned, particularly for bridges and waterside structures, many state and local authorities have started specifying drilled shafts rather than driven piles. Where the shafts must be constructed under water or slurry, visual inspection of most of the work is impossible, and one of several different Nondestructive Tests (NDT) is often specified. Contractors' experiences with these methods have varied considerably, and there is a great deal of controversy in the deep foundation industry over the reliability of NDT methods for assessing the integrity of foundation shafts or piles. The author has had more than 15 years of practice with the various NDT methods for deep foundations, on projects all over the US, particularly foundations for bridges and dock structures, and has developed an understanding of the "NDT controversy" as it has become known. In particular, experiences in the Pacific Northwest, California, and Alabama have illustrated the reasons for the controversy. This paper reviews these experiences, and suggests some steps that owners and contractors can take to reduce the risk of inconclusive or downright inaccurate test results.

Jan 1, 1998

By Lucia Kuizon

The Miranda Pine Roadless Area Review and Evaluation (RARE II) study area (No. 5114) comprises 12,600 acres (5,100 ha) in Los Padres National Forest in Santa Barbara County, California, about 15 mi (24 km) east of Santa Maria (fig. 1). Mineral investigations are made by personnel from the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and sampled mineral properties where appropriate.

Jan 1, 1983

By W. S. Wright, A. W. Tolonen

"INTRODUCTION The Mount Andrew iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by an engineer 4/ of the Bureau of Mines accompanied by geologists 5/ of the Federal Geological Survey. From October 20 to 27, 1942, two engineers 6/ of the Bureau of Mines made a further preliminary examination and took three large samples of magnetite and magnetite-copper ore for metallurgical testing. During the stunner of 1942 an investigation of the Mount Andrew-Stevenson-Mamie area, including topographic and geologic mapping and a magnetic survey, was made by geologist 7/ the Federal Geologically Survey. On May 31 and June 2, 1943, two Bureau of Mines engineers 8/ conducted a preliminary examination in which special attention was directed to trails, camp, and drill sites. They were accompanied on May 31 by L. A. Warner of the Geological Survey.During the period from September 1943 through September 1944 Bureau of Mines engineers 9/ completed a thorough investigation which included trenching, core drilling, and sampling. A Federal Geological Survey representative 10/ examined all trenches and cores for geological data.LOCATION AND ACCESSIBILITYThe deposit is situated at latitude 55º 31' N. and longitude 132º 18' W. on the north side of Kasaan Bay on Prince of Wales Island, Southeastern Alaska. The general location is shown on figures 1 and 2. The deposit is 5 miles southwest of the village of Kasaan and by water, 27 miles northwest of Ketchikan; the main tunnel portal is 7/8 mile north of the Mount Andrew landing on Kassan Bay."

Nov 1, 1947

By S. Banisi, M. Pourkani, A. Kargar, D. Hamidi, M. Sarvi

"Flotation circuit of the Sarcheshmeh copper mine, which processes 40,000 t/d of ore at 0.9% Cu, consists of rougher, cleaning and recleaning stages. To study the stage recovery of copper, one of the eight identical flotation banks was selected for sampling. It was observed that 17% of copper goes to the tailings and the lowest copper recovery was for particles coarser than 105 microns. The third five-cell unit of this bank not only did not recover appreciable amount of copper but also decreased the concentrate grade. The grade of the last five cells was lower than the feed grade suggesting that mixing of the concentrates of the three units was not beneficial. To alleviate the problem, the concentrate of the first four-cell unit was directed to the cleaners feed box (i.e., by- passing the regrind mill). This increased the overall copper recovery by 1.7 %. Also rather than the current practice of adding the reagents only at the feed tank (i.e., 100-0-0%), various combinations of stage addition were examined. It was found that 75-25-0% addition regime could increase the total copper recovery by 1.3%. At the recleaning stage in order to increase the final copper concentrate grade, a froth washing system was used. To ease the maintenance of the system, a shower type washing system was installed. The optimum wash water superficial flowrate was found to be 0.06 cm/s. Continuos sampling of the recleaners with and without wash water over a period of two months showed an increase of 1.5% in the final copper concentrate grade at constant overall copper recovery.INTRODUCTIONThe Sarcheshmeh copper ore body that may rank as third or fourth largest in the world contains 1 billion tonnes averaging 0.9% copper and 0.035% molybdenum. It is located in southeastern Iran and has been processing 40 000 t/d of ore since 1982. The mine produces 100 000 tonnes of copper and 2200 tonnes of molybednite concentrate per year.After three stages of crushing, the ore with a F80 (80% passing size) of 12.7 mm is fed to eight parallel ball mills in closed circuit with cyclones to produce a product 70% finer than 75 microns. The concentrate of rougher flotation circuit is ground; rougher tails constitute the main component of the plant final tailings. A concentrate with an average grade of 31% Cu (chalcocite and chalcopyrite) is obtained after cleaning and re-cleaning stages. Total recovery of the plant varies between 83% and 87%, depending on operating conditions and ore type."

Jan 1, 2001

By William J. Krisko

This contract final report summarizes the design, fabrication and testing of a "line brattice air curtain" device under Bureau of Mines Contract H0357097. The purpose of this program was to develop the concept of using an air curtain for coursing ventilating air parallel with the air curtain From the last open crosscut to the face in exhausting ventilation systems to replace the line brattice cloth in room and pillar coal mining operations. The final design of the air curtain device consists of a 10-foot long closed end pipe with c: slot cut along its length. Pressurized air is delivered to the open end with a hydraulically-driven blower. A sheet of air emanates from the slot and is directed toward the mine roof. An invisible sheet of air is thus created between the top of the machine and mine roof and acts a an extension of the existing conventional line brattice.

Jan 1, 1977

By Donald L. Katz

FIFTEEN years ago Dr. Manning published a paper in "Petroleum Development and Technology" on '.Fundamental Research Relating to Petroleum." He tabulated for several industries "the proportion of their present success which can be fairly attributed to the application of information and processes obtained by scientific research," giving petroleum a score of 7 compared to 100 for the electrical and coal-tar industries. Today the petroleum industry as a whole and the producing groups both have raised their score beyond the majority and are climbing toward the top. Present practices are being developed both by fundamental research and the application of the research method in field operation.

Jan 1, 1941

By Timothy P. Smirnoff, Tracy K. Lundin

INTRODUCTION The City of Phoenix, Arizona is located in the Phoenix Basin watershed which is prone to flash flooding several times each year. The runoff from these storms moves from the mountains in the north to the Salt River in the south. An extension of Interstate Highway 10 (1-10) will pass through the city east to west to form an Inner Loop through the downtown business district. PROJECT DESCRIPTION The I-10 Inner Loop extension will be a depressed roadway which would intercept the surface drainage of the Phoenix Basin and separate the watershed into two regions. To prevent flooding of the depressed roadway, runoff storm water collected from the northern half of the drainage area will be conveyed beneath the roadway to its natural outlet at the Salt River. A conveyance system composed of pressure tunnels beneath the city, shown in Figure 1, was proposed to achieve this goal . Table A presents the prominent features of each of the tunnels. This paper will describe geologic and engineering parameters specific to Phoenix which were used in the design of a series of tunnels to convey storm water from the I-10 Inner Loop to the Salt River. The design of tunnel initial and final support is described along with support and construction methods used by the Contractor.

Jan 1, 1985

By W. H. Somerton

The basic objective of this project was to determine the permeability of coal fracture systems as a function of effective stress. The detailed steps in accomplishing this objective are given in Article I of the contract under which the work was conducted as follows: Sec. 1.1 The objective shall be to determine the permeability of the coal fracture system as a function of effective stress. At least three bituminous coals shall be studied and at least five samples of each coal shall be tested. The sample size shall be as large as possible to be representative of coal found in the seam; a minimum of four inches is preferred.

Jan 1, 1974

By P. A. Lilly, W. Sarunic

In most cases, slope movement monitoring data are collected on a temporal basis and displacement or velocity is plotted against time in order to assist the engineer to make judgements about slope behaviour. Once an unusual behaviour pattern has been established, the data are then analysed to estimate when the key inflection points occur in the data, when the slope movements start to accelerate and, ultimately, when the slope is expected to collapse. The identification of these inflection points is sometimes difficult to achieve with the naked eye. This paper presents the application of a trend analysis technique, known as cusums, to assist in this process. The authors have presented a range of data from various real life examples which highlight the effectiveness of the cusums technique. A key aspect of the cusums technique is the use of a constant (K) against which data trends are assessed. This constant is best derived from slope performance data at each site, as each rock mass will behave in its own unique way. The authors have experienced slopes that have had threshold values ranging from 0.1mm/day through to 10mm/day, and therefore a conservative approach should be adopted when assessing the performance of slopes.

Jan 1, 2006

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the third report of investigations by the Bureau of Mines in cooperation with industry to establish the value of electrolytic manganese in the manufacture of ferrous and nonferrous alloys. The manganese was produced by the Bureau at its Boulder City pilot plant from domestic ores and by the process developed by it. 4/ The work was done under the direction of R.S. Dean, assistant director, Bureau of Mines, and R. G. Knickerbocker, chief, metallurgical branch. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steels 5/ and the second with its use in acid electric or open-hearth low- and medium-carbon steel castings. 6/The present report treats of the use of electrolytic manganese in the manufacture of low—carbon rimmed and killed steels. A résumé of these three investigations and two others appeared in the magazine STEEL. 7/ Further reports will be published as tests are completed at some 70 industrial plants. All tests were made on full—scale heats or melts, and the resultant product was processed and used commercially."

Jul 1, 1945

By James S. Graham

Foundation pile driving hammers used in New York City in the past 100 years have been drop, steam, compressed air, diesel, and hydraulic. In 1992, the first hydraulic hammer in the New York City area was purchased by Norwalk Marine Contractors, Inc. from Junttan in Finland. It was bought because of its variable energy and ease of mobilization, not because of its higher transferred energy. Heller and Johnsen engineers instrumented hydraulic hammers on nine jobs. The measured transferred energy for the nine jobs was found to average approximately 80 percent. There is no clear consensus regarding the reasons for the hydraulic hammer being more efficient in delivering energy to the pile as compared to single-acting steam/air impact hammers. To minimize pile damage during installation, and to minimize footage overruns, an up-to-date version of the wave equation software that includes an efficiency value of 0.95 for hydraulic hammers is now used.

Jan 1, 2000

By A. M. Evans

Because of an urgent national need for manganese, the deposits in the Little Florida Mountains of Lune County N. Mex., were visited by O.H. Metzger, an engineer of the Bureau of Mines, on June 12 and 13, 1940, accompanied on the second day by S. G. Lasky, a geologist of the Federal Geological Survey. After this preliminary examination, it was recommended that exploratory work be done by the Bureau of Mines on several properties in the district. An exploratory project of trenching, sampling, and core drilling was started by the Bureau of Mines in September 1940 and completed in May 1941.2/ Work was done on three properties - the Luna mine, the American group of claims, and the Manganese Valley mine. The Little Florida manganese district is situated on the eastern slope of the Little Florida Mountains about 2 miles south of U. S. Highway 80-90, 12 to 14 miles southeast of Deming, Luna County, N. Mex. The principal claims comprise the Luna Manganese, American, and Manganese Valley groups.

Jan 1, 1949

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control of anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/. These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the mounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating beers dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By Yoginder P. Chugh

Most mines are large producing 0-25 mmt annually. The coal is mine.) at depths ranging from .0-150 m 120-500 ft mining at 300 m .(,1000 ft) depth is anticipated in the future. Single and multiple seams ranging from 3-12 m 10-40 ft) in thickness are mined. Most overburden is unconsolidated and consists of sands, and sandy or silty clays. The stripping ratio (volume of overburden to volume of coal mined) varies from 3-L. The overburden and coal is mined in benches 8-12 m -(24-40ft) high; the high-wall angle is about 45 degrees. Bucket wheel and bucket chain excavators are commonly utilized for overburden and coal removal, Some of the large overburden stripping machines nave capacities. Ranging from 4400-10,000 bank cu ( 6000-14,000 BC) per hour. The overburden from the upper benches is transported around the pit using the trains and belt conveyors. It is deposited in the spoils using large stacker-conveyor systems capable of handling 2550-7300 cu m/hour (7500-10,000 cu yds/hour). The overburden from the bottom two or three benches is transported across the pit using the conveyor bridges which are computer controlled. Conveyor bridges capable of handling overburden up to 60 m (200 ft) high are currently in use; a 60 a (20e ft) high conveyor bridge has a capacity of 85 x 10 cu ( 118 x 10 cu yd) annually. The coal is loaded in the trains directly and shipped to power plants or coke oven plants.

Jan 1, 1980

By Oliver C. Ralston

[This paper is an expanded revision of a report entitled "Froth Flotation and Agglomerate Tabling of Nonmetallic Minerals, " published in Transactions of the Canadian Institute of Mining and Metallurgy (vol. 40, November 1937, pp- 691-726) and prepared a year previously. Revisions embodied herein brine the data up to January 1, 1938. References have also been added to make the earlier paper more complete for the period it covered.]

Jan 1, 1938

By Alexandre Silva Guimarães

O presente trabalho avaliou o comportamento de extração dos metais cálcio, magnésio e níquel, contidos em licores sintéticos sulfúricos, utilizando-se o extratante Cyanex 272 (0,64 mol/L) e misturas entre Cyanex 272 (0,64 mol/L) e ácido versático (0,53 mol/L). Os resultados revelaram que a adição de ácido versático ao Cyanex 272 provocou um aumento nas extrações de cálcio, que atingiram cerca de 40% em pH = 5,1, decrescendo com a elevação do pH do licor até atingir aproximadamente em 15% pH = 5,9. As extrações de níquel (em torno de 80% em pH = 7,1) foram favorecidas, enquanto as extrações de magnésio permaneceram em torno de 75-80%, numa faixa de pH entre 6,0 e 7,0, em comparação com a utilização de apenas Cyanex 272 como extratante. O níquel pode ser separado dos metais cálcio e magnésio, pela mistura dos extratantes nas concentrações estudadas, em pH = 5,1, utilizando-se de 2 a 3 estágios de contactação.

Aug 7, 2018

By D. C. Lynch

While a sizable amount of data exist as to the activity and distribution of minor elements between matte and metal, there has been no unifying theory presented delineating the form of dissolution of these elements in molten sulfides. In order to alleviate that deficiency the literature concerning the behavior of As, Sb, Bi and Pb in mattes is reviewed. Models present in the literature, regarding the thermochemical behavior of minor elements, are tested, and new models are presented and evaluated using thermodynamic theory. The results of those analyses are used to predict optimum conditions for the volatilization of minor elements. The dearth of data on the behavior of minor elements in nickel mattes requires that this review focus on copper- iron mattes. An effort is made, however, to utilize basic knowledge regarding nickel sulfides and the interaction of nickel with the minor elements to predict the behavior of those elements in nickel-copper and nickel-iron mattes.

Jan 1, 1993

By H. H. Yancey

In this information circular is presented a summary of the more important articles that nave appeared in the literature pertaining to the experimental work and to the commercial operation of the froth-flotation and Trent processes as applied to the cleaning of fine coal.

Jan 1, 1933