Search Documents

By D. Goossens

Quality control is a system which should guarantee that quality is achieved. It is the execution and verification of a project in an organised way, in order to obtain the maximum of certainty that the results meet the requirements. This concerns all stages of the project, from the soil investigation, over the design, to the execution. Quality control can and has been successfully realised for important projects by means of a quality plan. A quality plan is based on a number of general considerations, but should certainly be focussed on the particularities of a specific project. Practical examples of quality plans, which have been realised on sites in Belgium, are developed and the advantage of the system is shown by concrete case studies.

Jan 1, 1996

By Harold L. Rhodes

The Bureau of Mines has developed a method for determining the H2S content in natural gas samples. A gas chromatograph with a flame photometric detector was used to analyze samples with H2S concentrations ranging from 5,000 ppm to a minimum detectable limit of 0.01 ppm. A mass spectrometer was used to analyze samples containing H2S in amounts greater than 5,000 ppm. Methods are presented for preparing containers for H2S samples and for preparing standards using partial pressure and weighed standard methods, Sample collection techniques are discussed, as are analytical results which illustrate the loss of H2S while in the sample container and provide a basis for evaluating containers used for sampling and standard preparation.

Jan 1, 1979

By Francis Church Lincoln

"INTRODUCTION During the period from September 18 to November 27, 1944, the Bureau of Mines conducted an investigation and exploratory churn-drilling program in an area immediately north of the Crow Branch Diggings, a district lying approximately 2 1/2 miles southwest of the town of Livingston in Grant County, Wisconsin.The work was undertaken as part of a general Bureau of Mines investigation of the zinc-producing area of southwestern Wisconsin at a time when all effort was being made to increase the production of metals important to the Nation's war prrgram.Although no mining has been done in the district in recent years the Crow Branch Diggings were an important source of galena and may be found today in the dumps remaining from old surface-mining operations.The Bureau of Mines undertook an exploratory churn-drilling program on the northwestern projection of the general strike of the digging in a zone where subsurface,lead and zinc mineralization had been reported from drilling done in the early 1900's."

Feb 1, 1947

By K. C. McMahon

This report is the result of the engineering efforts performed by the Mining Equipment Operations of FMC to develop methods of automating a continuous miner. This work was done as part of modification number three of the contract for the development of a miner/bolter system. As the demand for energy places an ever-increasing pressure on the coal mining industry to produce more coal, methods for underground mining which will increase productivity with a con-current increase in safety are being actively sought. Removing the machine operator from his station on the continuous miner and placing him at a safer location behind the machine while retaining his control functions via an umbilical cable or a radio link was an important first step. However, the problems of poor visibility, no control "feel", and the judgmental problems of controlling the sump distance and the shear limits have not been conducive to the productivity increase that is desired.

Jan 1, 1975

The Wednesday Morning Session of the Rocky Mountain Coal Mining Institute was called to order by Albert Keenan of the Thompson Creek Coal and Coke Company, Denver, Colorado, in the absence of the President. He introduced Edward Prostel of the University of Wyoming Natural Resources Research Institute, Laramie, Wyoming, who spoke on "Coal Utilization Work at the University of Wyoming." (Please refer to the index for printed text of the paper.) Following Mr. Prostel's talk, R. Park Lamborn of the National Mine Service Company, Pittsburgh, Pennsylvania asked Mr. Prostel two questions: (1) What -has been done in tar research? and (2) Has there been large scale research on brickets? Mr. Prostel stated that he could not say too much about the first question as this research was done in the petroleum department and he would prefer to have a chemist talk about it. As to the second question, the system of carbonization is a big project. There are many possibilities. At the University they are trying to do that in the same unit that produces the char. This system was introduced in Canada. The brickets are bound with sulphite liquor. Mr. Schloss asked Mr. Prostel to report on a project that they have been working on at the University, and Mr. Prostel stated that some time ago they began to experiment to see if it would be economically possible to dry coal at the mine (coal containing 30% moisture) and then ship it a distance of 130 miles to be used. Results are that it would be possible, but will require a considerable quantity. He felt it might be possible to operate such a scheme in a few years.

Jan 1, 1957

GARY STUBBLEFIELD RMCMI PRESIDENT 1993-1994 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 90th Regular Meeting and Convention June 26 thru 28, 1994 Snowmass Resort, Colorado

Jan 1, 1993

By Osama El-Fiky

There are many types of deep foundations currently being used in the San Francisco Bay Area, one of the most common being driven precast, prestressed concrete (PC/PS) piles. PC/PS piles are frequently selected for use due to of ease of installation, availability, and relatively low cost. Disadvantages of using PC/PS piles are noise, vibrations, pollution, front-end delays due to indicator pile programs, and reduced flexibility. An acceptable alternative to driven PC/PS piles was selected for construction of foundations for the heavy housing and administrative buildings at the San Francisco County Jail #3 replacement project in San Bruno, California. The pile type selected, the Auger Pressure Grouted Displacement (APGD) pile, was chosen to reduce noise, vibrations, installation time, and cost, and to allow for greater flexibility of installed pile lengths. This paper presents a case history of the use of APGD piles that were substituted for driven PC/PS concrete piles for the subject project. Standard and quick loading pile load tests were performed to confirm adherence with the design criteria originally used for the driven PC/PS concrete piles. The APGD piles were found to increase shear strength around the piles similarly to driven displacement piles. In addition, this paper presents the methodology used in monitoring APGD pile installation.

Jan 1, 2002

The Bureau of Mines in the Department of the Interior is increasingly concerned with the safety and health of personnel engaged in coal-mining operations, particularly below ground. The Bureau is also concerned with improving the utilization of domestic mineral resources, and reducing the environmental impact of mineral operations. One obvious way to improve safety and minimize health hazards would be to eliminate coal mining entirely by bringing the energy value of the coal to the surface in some other way, such as by partially burning it underground to form combustible gases and bringing these gases to the surface, where their energy content can be put to use. This technique might also improve the utilization of the coal resource. ? Accordingly, the Bureau of Mines, interested in re-evaluating underground coal gasification technology in terms of current and expected conditions in the United States, requested Arthur D. Little, Inc., (ADL) to appraise the technology to determine: ? Whether the current (1971) state of the technology offers a technically feasible method for gasifying coal underground that is applicable to the reserves of bituminous and lower rank coals in the United States. ? Whether a program of research and further development of the technology could ultimately make it a technically feasible alternative to current open-pit and underground coal mining operations. ? What the nature and cost of further research and development work in the technology should be.

Jan 1, 1971

By J. Mitchell Linnet

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of deposits in the Bucks Lake and Chips Creek RARE II areas in Plumas and Butte Counties, California. These areas lie along the west slope of the Sierra Nevada on opposite sides of the North Fork Feather River and encompass an area of 62,800 acres (25,400 ha). Metasedimentary and metavolcanic rocks of the Pennsylvanian Calaveras Formation are intruded by plutons of Mesozoic age. Mineral; of economic iterest are in quartz veins in metasediments close to these plutons; they are principally gold and silver with minor amounts of copper, lead, and zinc minerals. Molybdenum, copper, silver, and tungsten minerals occur in tactite along metasedimentary-granitic rock contacts. In both areas, auriferous Tertiary channel gravels have been extensively developed. Asbestos occurs in ultramafic rocks in both areas, and a limestone deposit was explored in the Chips Creek area. Gold is the principal economic mineral in the Bucks Lake RARE II area. The Shenandoah Mine (fig. 1, no. 19) contains 7,500 tons (6,800 t) of indicated and inferred subeconomic gold resources in sulfide-bearing, silicified metamorphic rocks of the Calaveras Formation (table 1). Similar rocks have yielded gold at the Edman and Megowen Mines, adjacent to the area. A high potential exists for additional lode resources in the area around the Shenandoah Mine. Callahan Mining Corporation personnel believe a multi-million ton disseminated gold deposit underlies the property.

Jan 1, 1983

By Edward Cadwell

El presente texto señala la clasificación de combinación de minerales a través los desperdicios estériles y altos y concentrados bajos.

Jan 1, 1959

By Griffith. F. E., Glei

"INTRODUCTION For many years protective grounding of electrical equipment has been advocated as a means of safeguarding equipment against damage and of minimizing shock hazards to persons. Several codes are in effect covering in considerable detail the items to be observed in obtaining effective grounding in and about industrial plants. Although the coal-mining industry does not have a comprehensive code of its own covering the grounding of electrical installations, a number of States and individual coal-mining companies have issued codes, standards, or rules that include certain requirements with reference to grounding. As early as 1916, 4/ and again more recently, 5/ the Bureau of Mines recommended grounding, particularly as a means of preventing shock to men working on or around electrical equipment.It is common knowledge among electrical engineers of public utility and mining companies that connecting a wire from the frame of a machine to a rod or pipe driven into the earth does not necessarily assure desired protection of surface equipment. In fact, it has often been found necessary to use several interconnected rods and to treat the surrounding earth with salt or other chemicals before the connection to earth would have sufficiently low resistance to give satisfactory results. Even these expedients have not produced the desired results in some localities. It has also been found that ground connections initially having a low resistance may attain high resistance during some seasons of the year. In spite of such difficulties with surface equipment, it has sometimes been assumed that a mining machine resting on the floor in a coal mine is grounded by virtue of its contact with that floor. It has also been assumed by persons endeavoring to comply with grounding requirements that a peg or rod driven into the mine floor would provide a sufficiently low-resistance contact with the earth to be satisfactory as an electrode for connecting the grounding wire from frames of equipment. That both assumptions may be wholly untrustworthy has been proved by the authors in actual tests with underground machinery."

Dec 1, 1943

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

By Theodore R. Jolley

The estimated recoverable reserves in the area in the vicinity of Eska 2 mine are, 699,300 tons in the Chapin and Emery bas of the Maitland group. Those recoverable reserves are in the area between the Eska fault zone and Jonesville fault and extend down dip from the outcrops. No reserves were developed by the Eska 2 entry or by drill hole 14-16 in the Eska fault zone. The small quantity of reserves in the vicinity of the Eska 2 mine is insufficient to justify development of a now, modern .nine in this area. The estimated recoverable reserves in the area east of aka Creek are 974,500 tons in the Eska, Shaw, and Martin beds of the Eska group. Most of those reserves occur in the south limb of the syncline. It will be necessary to practice subjacent mining methods to recover these reserves in the Eska group. The Eska bed developed by the diamond drilling in this area comprises coal end few thin partings. The Shaw and Martin beds comprise two bunches of coal separated by partings, and the product from full-bed mining will require thorough preparation.

Jan 1, 1952

By Gabriel Burlandy Mota de Melo

Manchas de óleo em um meio aquoso foram removidas utilizando compósitos de parafina com nanopartículas de ferritas de cobalto (CoFe2O4), níquel (NiFe2O4) e níquel-zinco (Ni0,7Zn0,3Fe2O4), nas proporções de 13,0% e 28,5% em peso. Para avaliar a eficiência da remoção, foi determinada a velocidade dos compósitos ao serem acoplados a uma mancha de óleo na superfície da água e submetidos ao campo magnético de um imã permanente. O melhor desempenho foi obtido com o compósito de parafina contendo 13,0% em peso de ferrita de níquel-zinco.

Aug 16, 2017

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By George P. Demopoulos

In this paper the production and stability of crystalline scorodite (FeAsO4·2H2O) is discussed both on the basis of previously published work as well as recent work performed in our laboratory. The production of scorodite, especially from arsenic-rich and iron-deficient sulphate solutions offers a number of operational advantages such as high arsenic content, stoichiometriciron demand, and excellent dewatering characteristics. In addition to hydrothermal production of scorodite the work done over the last 10 years in our laboratory has determined that it is feasible to produce scorodite by step-wise lime neutralization at 90°C. The atmospheric scorodite possesses the same structural and solubility characteristics with the hydrothermally produced scorodite. Long term equilibration tests (up to 66 weeks) in the pH range 5 to 9 and temperatures from 22 °C to 75 °C revealed scorodite to undergo slow incongruent dissolutionyielding a highly metastable nano-sized 2-line ferrihydrite phase. The equilibrium arsenic concentration with this phase was 0.35, 0.96 and 5.87 mg/L at pH 5, 6, and 7 respectively at 22°C. In the presence of gypsum slightly lower concentrations were measured, this being more pronounced at pH>7. It was tentatively deduced that a Fe-Ca-AsO4 association (in the form of a phase resembling the mineral yukonite) contributes to the lowering of As concentration. Finally thermodynamic calculations determined that scorodite is stable in the presence of ferrihydriteunder oxic conditions up to pH 6.75 at 22 °C or higher pH at lower temperature and gypsum-saturated solutions. Keywords: Scorodite, Crystallization, Arsenic, Solubility, Stability, Precipitation, Disposal, Extraction, Processing, Metals, and Environment.

Jan 1, 2005

By Bernadette C. Michalski

Mineral raw materials, labor, capital, and technology form the basis of industrial production. The augmentation of one or all of the elements--labor, capital, and technology--will result in industrial growth. Thus, an increase in the labor force would increase output. A similar result would be achieved by expanding capital investment and supplying labor with more equipment. Finally, industrial growth can be achieved by introducing more productive methods and techniques born of technological advancement. The Soviet Union has employed these elements in many patterns to catapult from an agricultural to an industrial economy in four decades. The early history of the Soviet Union was marked by limited capital and borrowed technology, forcing the Soviets to concentrate on an abundant labor reserve to support the industrial program. The source of this reserve was the rural population. In [1928], 80 percent of the working population was employed in agriculture. This figure dropped to 43 percent by 1956, whereas industrial employment in the same period increased from 8 to 31 percent.3/

Jan 1, 1960

By Robert H. Townsend

The following paper discusses the mining, transportation, and crushing methods, with costs, at the San Andreas plant of the Calaveras Cement Co. It is one of a series, prepared for and published by the U. S. Bureau of Mine describing methods used in cement-rock quarries throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total cost. It is recognized that publication of total costs mightin some instances cause embarrassment to individual producers as well as to the industry as a hole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost-tabulations shall ensue.

Jan 1, 1933

By D. W. Blaylock

1. The Lower Freeport and Lower Kittanning beds are the most important beds in Clearfield County, Pa., from the standpoint of production. The Lower Kittanning bed has the largest remaining recoverable reserves of any of the beds in the county. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,909 million short tons as of January 1, 1953. Of this total, 1,177 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Peter Yen

This session consists of five papers. Three involved research on the properties of grout materials, specifically ultrafine cements and polyurethane grouts. Two papers present the development of soil grouting technology and monitoring methods. Of great interest are the papers on ultrafine grout penetrability testing focusing on the pressure filtration effects encountered in permeation grouting applications (Ericksson, Stille and Mittag, Savidis). The comparison testing of hydrophilic and hydrophobic polyurethane grouts submitted by Vrignaud, Ballivy, Perret and Fernagu assessed the long-term performance of these materials for repairing saturated cracks in concrete, subject to thermal expansion and contraction. Two very practical papers present the development of soil grouting, where permeation, fracture, replacement, jetting and other grouting techniques are utilized. The papers by Lees with Chuaqui and Warner present experience with ultrafine and other commonly used grout materials. Methods to measure and monitor the injection process and verify production progress are discussed.

Feb 10, 2003