Search Documents

Jan 1, 1971

By T. M. Barczak

Stoppings are required to resist lateral forces on the face of the structure to control pressure differentials created by ventilating air. The design criteria in other parts of the world, including Australia, exceed this requirement by specifying over pressurization control to as much as 14 kPa (2 psi) in the active sections and 35 kPa (5 psi) in the main ventilating control areas. This is done to provide protection to the mine workers from explosive or air blast events within the mine that can create this over pressurization. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research to develop a new testing protocol for rating mine ventilation stoppings. The premise of this work is that arch-loading conditions more accurately reflects the transverse load capabilities of stoppings in underground coal mines than the freestanding flexural strength test specified in the current Code of Federal Regulations (CFR). This work clearly shows that the transverse load capabilities of dry-stacked, mine ventilation stoppings are dependent upon the material strength of the block and the height and thickness of the wall, none of which are part of the current CFR criteria based on ASTM E-72 specifications. This paper compares the transverse load capabilities of several block materials and wall dimensions commonly used in stopping constructions based upon simulated three-hinge, rigid-arch loading tests of half-wall constructions in the NIOSH Mine Roof Simulator. The results indicate a wide-range of transverse load capacities, ranging from as low as 21 kPa (0.3 psi) to as much as 117 kPa (17 psi) for the conditions evaluated in this study. The current CFR criteria do not distinguish between applications of these stopping designs despite their wide variance in transverse load capabilities, which is not conducive to employing ventilation control strategies that isolate certain sections of the mine to prevent injury to mine workers.

Jan 1, 2009

By J. Nielen van der Merwe

Rock engineering research and technology development in South Africa only received serious attention in reaction to the Coalbrook disaster in 1960. At the time, a number of gaps in knowledge of rock related matters were identified and in the ensuing years, these were progressively attended to. The paper describes the events that led up to the Coalbrook disaster and reviews the developments that took place afterwards. The effectiveness of the research outcomes are tested by referring back to the disaster. It is concluded that tremendous advances were made but that not all the unknowns were attended to at the same level. The strength of nominally square internal pillars is the one issue that received the most attention, but the strength of barrier pillars, overburden behaviour and loading systems are still largely unknown. Due to the complexity of the remaining unknowns, they can and should be addressed by the application of back calibrated numerical models. There are no readily available simple analytical solutions. The state of mining rock engineering research in South Africa borders on an emergency. More than a 1000 years of aggregate research experience has been lost in the last three years and funding is under severe pressure. There are disturbing parallels between the current positioning of the industry as a whole and the Coalbrook mine in the years preceding the disaster.

Jan 1, 2006

By B Nielsen, H Lehto, J Rohleder, C Robben

Sensor-based ore sorting is being increasingly used to reduce the amount of low-grade and waste material processed in mineral concentrators. This type of preconcentration provides bottom-line benefits to users by reducing the amount of energy, water and consumables, as well as reducing capital cost. Existing operations can increase metal production, while previously uneconomic deposits and low-grade stockpiles can also be exploited. The technology can also be used to separate ore types for selective processing. The path to implementing sensor-based sorting may include:• geometallurgical evaluation• first inspection testing to investigate sensor response• bench-scale testing where sensor selection is not obvious or for difficult applications• performance testing in full scale sensor-based sorting machines• larger scale site-based piloting with a temporary semi-mobile plant installation. Sorting requires material to be suitably prepared and presented to the machines and typically this consists of crushing and screening to limit top size and optimise liberation. However, where material streams are suitably sized and prepared, additional equipment may not be required (e.g. the sorting of semi-autogenous grinding (SAG) Mill pebble streams).This paper presents a case study of economic upgrading of gold ore, by preconcentrating with sensor-based ore sorting. The case study examines sorting amenability, test work, the feasibility study through to implementation, with associated flow sheet development. The development process is analysed and evaluated with a view to rationalising the process for development of future projects. In addition, limited financial modelling based on expected results is shown to illustrate the benefit to the operation.CITATION:Nielsen, B, Rohleder, J, Lehto, H and Robben, C, 2017. Sensor-based ore sorting to maximise profit in a gold operation, in Proceedings MetPlant 2017, pp 131–146 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By Chris M. Haberfield, Neil D. Benson

The assessment of overall modulus (or stiffness) of a fractured weak to moderately strong rock mass is a key parameter in the design of civil engineering works in these materials. It also provides the highest level of uncertainty due to scale effects, anisotropy and the influence of joint frequency and joint stiffness. Using the example of the Melbourne Mudstone, this paper compares approaches using empirical rules based on intact rock strength, laboratory testing, in situ field testing, semi-quantitative assessment techniques based on rock mass classification and back analyses. L'évaluation du module (ou rigidité) global d’une masse rocheuse faible et fissurée a modérément forte est un paramètre principal dans la conception des travaux du génie civil dans ces types de matériaux. Elle fournit également le niveau le plus élevé d'incertitude due aux effets d’échelle, à l'anisotropie et à l'influence de la fréquence et de la rigidité des joints rocheux. En utilisant l'exemple du schiste de Melbourne, cet article compare des approches empiriques basées sur la force intacte de La roche, les essais expérimentaux au laboratoire, les essais sur site, les techniques semi-quantitatives d'évaluation basées sur la classification de la masse rocheuse et les analyses en retour. Die Schaetzung des allgemeinen Steifigkeit-Moduls des gebrochenen schwachen bis zu maessig starken Felsmassen ist eine Haupt- Annahme in dem Entwurf von Tiefbau-Projekten in diesen Materialien. Es verursacht den hoechsten Grad der Ungewissheit in Folge der Groessenordnung, Spaltorientierung und dem Einfluss der Haeufigkeit der Risse und Bruch-Steife. Unter Verwendung des Beispiels des Melbourner Tonsteine, vergleicht diese Darlegung die Anwendung der empirischen Regeln, die sich auf die Staerke des ungestoerten Fels Basieren mit Versuchen in der Material Pruefungsanstalt, Untersuchungen auf der Baustelle und halb-quantitative Schaetzungsverfahren, die sich auf die Felsmassen Klassifikation und fruehere Analysen stuetzen.

Jan 1, 2003

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By M. Helinski

In the authors? experience inappropriate water management in hydraulic fill masses has been the root cause of most barricade failures. Inappropriate water management can lead to high water pressures, reduced effective stresses and increased barricade stresses (Kuganathan 2002). In addition the high hydraulic conductivity and non-plastic nature of most hydraulic fills makes susceptibility to piping failure (Cowling et al. 1987) a high possibility in many hydraulic backfills where a static water head is available. In order to avert both of these failure mechanisms it is essential to control the elevation of the phreatic surface within the fill mass. This is usually achieved through campaigned filling and resting periods. The duration of filling and resting periods are often estimated using some form of stope drainage simulator. Due to the random nature of many characteristics that influence the fill mass hydraulic conductivity, simulation of hydraulic fill drainage can be difficult. The high consequences of inaccurate phreatic surface estimates combined with the high variability in drainage properties often results in operators taking a conservative approach to this modelling. This conservative approach can lead to significant delays in the filling cycle which can have a major impact on the productivity of many hydraulic fill operations and can often results in an unnecessary movement towards capital intensive paste fill systems. This paper presents a water management technique which combines a simplified drainage model with in-situ monitoring to provide a rational approach to water management. With an accurate drainage model filling operations can be carried out at optimum efficiency without compromising safety. The implementation of this strategy has lead to a significant increase in filling rates at a number of Australian filling operations. A brief case study from one of these sites has been presented.

May 1, 2007

By P. J. Brereton-Stiles, M. S. Rennie, N. Singh

Ferroalloy producers are large-scale users of electrical energy, which in many countries is in short supply and increasingly expensive. Preheating and/or pre-reduction using natural gas, recycled furnace gas or coal fines have lowered the specific use of electricity, but the high energy concentration necessary for most reduction processes can be achieved only by the use of high electric currents. Most countries have insufficient electricity to supply the demands of industry and the domestic consumer, particularly during certain periods of the day and certain times of the year. The generation and distribution of electricity is a large-scale expensive business, which is financed and managed directly or indirectly by government bodies in most countries. Both economic and political imperatives determine how much electrical energy is made available to whom and at what price. In South Africa demand is set to outstrip supply within the next few years, and the local supplier Eskom has moved from a traditional demand tariff pricing structure to a time-of-use tariff pricing so as to limit peak demand usage. This will mean a substantial increase in electricity cost to those users unable or unwilling to reduce consumption during peak periods. The optimal use of the available electrical energy depends both on the process, the furnace size, the configuration and infrastructure of each plant and its cost structure. As the cost and availability of electricity is set to change dynamically, the management of the situation becomes a real time control and optimisation problem. This paper discusses some the process and operational constraints associated with low- or no-load conditions and how to manage the situation. Electrode management will be one of the key issues.

Jan 1, 2004

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

By A Rorke, B Cubitt, R Beeslaar

The recent drop in the value of the South African Rand has resulted in an increased export value for South African coal and has lead to new coal reserves becoming available for mining. Very often these reserves are in close proximity to existing structures and utilities thus calling for stringent blast control measures to keep the risk of vibration, air blast and fly rock damage to a minimum.

Jan 1, 1997

By M. M. Gadde

Recent regulatory changes in the United States make it mandatory to conduct structural analysis of coal mine seals used to isolate abandoned workings from active mining areas. Different loading criteria are available for seal design depending on whether gob composition is actively monitored and maintained or not and whether the gob conditions lead to deflagration or detonation type loading. Since the loads involved in seal designs are dynamic in nature, the structural analysis must be made using dynamic stress analysis techniques. However, because of the significant complexities involved in conducting dynamic analyses, some designers use approximate simplified techniques to address the design problem. In this paper two such simplified methods are critically evaluated for their suitability to design coal mine seals. The benefits and limitations of the simplified methods are also outlined. Some comparisons are made to show the differences between sophisticated three dimensional dynamic analyses and the simplified methods and to delineate the problems associated with the latter approaches.

Jan 1, 2009

By T Smith, J Hatley

With the increased focus on the need for more uranium mines, this paper presents the design process currently underway for the development of the Millennium deposit in northern Saskatchewan, Canada. This deposit, located 630 - 750 m below surface, will be accessed by two shafts and will be mined by blasthole stoping methods at less than 500 t/d. Mining grade will approximate two per cent U3O8 and mine life is expected to be six to seven years. The project is a joint venture between Cameco, AREVA and JCU. This paper discusses in detail methods used to predict worker radiation exposures, the methods used to monitor the work environment and procedures unique to the uranium industry necessary to minimise worker radiation exposures.

Jan 1, 2008

By Anthony T. Iannacchione

The Roof Fall Risk Index (RFRI) is a new method introduced by the National Institute for Occupational Safety and Health (NIOSH) to assist the underground stone mine operator in 1) assessing defects the mine strata and 2) rating the relative roof fall risk these defects pose. The RFRI utilizes observational techniques to identify defects in the roof strata caused by local geologic, stress, and mining conditions. Assessment values for ten defined defect categories provides the foundation for estimating a range of risk conditions between 0 and 100 that define the potential for a roof fall. This paper examines how the defect information is collected using two field verification sites and proposes methods to analyze the RFRI data. These examples provide information on how well the method replicates observed conditions and how it might be applied in practice.

Jan 1, 2006

By Kiseong Hyeong, Young-Tak Ko, Gee Soo Kong

"The benthic environmental impact experiment addresses environmental impacts at a specific site related to deep-sea mineral resource development. For such a purpose, since 2010 we have carried out essential environmental research at both the BIS and a preservation site. We have acquired several tens multi- or box core samples at 32 sites within the BIS especially between 2011 and 2013, aiming to examine the basic properties of surficial deep-sea sediment as the potential source for deep-water plumes.In this study, we present physical the properties such as water content, shear strength and also geochemical properties such as major elements, rare earth elements (REEs), heavy metal contents at the BIS. Such proxies vary distinctly according to the Facies association. The lithology of all core sediments in the BIS corresponds to both Association Ib (Unit I/Unit II) and Association IIIb (Unit I/Unit III) on the basis of the KORDI classification (KORDI, 2004); Unit I is watery mud and dark grayish brown (10YR4/2) to dark brown (10YR4/3). Unit II is highly bioturbated mud and brownish yellow (10YR6/6). Unit III is very dark brown (10YR3/2) to black (10YR2/1) mud. Physical properties of these sediment types show that Association Ib is distinct from Association IIIb. The vertical profile of water content changed more sharply in Association IIIb probably due to compaction; water contents varied from 230 to 300% in Association Ib and changed from 200 to 250% in Association IIIb. The vertical profiles of shear strength are also quite different between Associations; the profile curve in Association IIb is much more gentle due to bioturbation."

Sep 1, 2014

By J. A. Flinn

Phelps Dodge’s Morenci copper mine has had six drills, six track-dozers, 16 shovels, two loaders, and 90 haul trucks equipped with either Caterpillar, Aquila, or Modular GPS systems for nearly three years. The Caterpillar Computer-Aided Earthmoving System is an open-architecture system, which allows for inputs to enhance orientation solutions and system functionality. This system has begun a new phase that leads to an intelligent mining system. Optimization techniques of the current system and inputs are reviewed. In addition, some practical issues of implementing new technology in a mining environment have been identified to aid in this new phase.

Jan 1, 2000

By J. A. Mielczarski

Surface properties of minerals could be modified selectively and very specifically by adsorption -desorption (dissolution) processes. This requires a monitoring and control of the outermost surface layer at a molecular and atomic level. The nature and structure of self-assembled submonolayers and monolayers at the interface of minerals were studied by infrared reflection spectroscopy. The external reflection spectra of the adsorbed monolayers on any type of minerals: transparent, opaque or non-transparent, recorded at different angles of incidence and for two polarizations are an excellent source of information about the nature and surface distribution of the adsorbed species. The developed method allows to obtain detailed information at a molecular level about the adsorbed surface species. By combination of the simulated and experimental data, the qualitative description of the adsorbed species as well as quantitative evaluation of orientation and the thickness of the adsorption layers were obtained. This fundamental knowledge allows to determine the mechanisms of surface phenomena which govern selective separations. Examples of different surfactant - mineral systems and industrial applications will be discussed.

Jan 1, 2000

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008