Search Documents

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Bob Rautenberg

The Construction of Tunnel and Edison Force Mains contract involves the installation of two new force mains to provide a redundant means for sewage conveyance from Middlesex County Utility Authority?s (MCUA) Edison Pump Station on the northern shore of the Raritan River to the Central Wastewater Treatment Plant on the southern shore. The force mains will be installed in a 1,192 m (3,910 lineal foot) long tunnel with a 4.09 m (13'-5') inside diameter, fully gasketed precast concrete segmental lining, which is to be tunneled underneath the Raritan River utilizing an Earth Pressure Balance TBM. The tunnel is anticipated to encounter flowing soils near and beneath the river. Two new 60-inch diameter Centrifugal Cast Fiberglass Reinforced Polymer Mortar force mains will be installed within the tunnel leaving an open utility corridor above the force mains for future consideration. The project also includes the design and construction of two slurry wall shafts with associated piping. The paper will provide an overview of design and provide a case history of the construction of the tunnel and highlights of the construction methods implemented to date.

By K. Hopperstead

Ventilation planning in trackless metal mining is often taken for granted. This paper highlights the trials of planning and executing the ventilation design for Bog Zone at the Lisheen Mine. Ventilation planning for Bog Zone started at the feasibility study stage in 2003; subsequent design changes continued until 2006. In August 2006, the development of the Bog Zone ore body was accelerated through the use of contractors; in addition, the Lisheen equipment fleet was revised based on a larger load and haul fleet. As a result, the circuit was reviewed in terms of changes in design conditions and best practices. This review resulted in a 40% increase of total airflow required to mine Bog Zone. Resources utilized to design the circuit include: external review, computer modeling, and in-house Lisheen planning and operational staff review. The final ventilation design configuration was adopted in 2007, after modeling and evaluating 30 different scenarios, resulting in a better distribution of airflow, optimized secondary escape way, reduced contaminants, and a total power reduction. The value of investment in computer modeling of primary ventilation circuit and planning for staged implementation should never be underestimated.

Jan 1, 2009

Work undertaken in the field of cut-off grade optimization has not advanced much beyond the work undertaken by Lane in 1988. His definitive work is based on the calculus of the Net Present Value criterion which is the most widely understood, consistent, and appropriate method by which sequential cash flows arising from the extraction of mineral reserves from an exhaustible resource can be represented. Although the mathematics is not complex Lane’s method is not a widely appreciated or applied approach to maximizing the value of a mining operation through selection and balancing of operational cut-off grades. Three stages in a mining operation namely, mining, processing and marketing were defined by Lane and the economics of each stage are identified and isolated to provide an optimum cut-off for each stage. Points of intersection along the present value curves for each stage of a mining operation are used to identify balancing cut-off grades at points where the capacity of the mining, processing and marketing stages is fully utilized and the Net Present Value of the operation is optimized. Data that simulate a small, deep-level Witwatersrand-type gold mine with an average grade of 6 g/t Au and a logrithmic variance of 1.2,are applied to the model to illustrate the benefits of representing cut-off grades in terms of present value curves for different segments of a mining operation. Keywords: Cut-off grade, Net Present Value, grade-tonnage curve, balancing cut-off grade, mining, processing, marketing.

Jan 1, 2003

By A. F. Raschenko, Y. A. Golodcov, V. V. Elshin

"The autoclave noble metal desorption in apparatuses with a dense stationary sorbent layer is perspective for the technology of sorption gold and silver extraction from solutions and pulps by carbon sorbents. The study of the mechanism and optimization of the autoclave desorption process involve some difficulties. To overcome them it is necessary to use mathematical and quantum-chemical modelling. The given paper deals with a mathematical model for the dynamics of gold and silver desorption from active carbons by alkali solutions based on the physical-chemical notions of the process. The kinetics and the mechanism of the process were investigated using the mathematical model for gold and silver desorption.The calculation of the efficient mass-transfer coefficient (ße) for various initial and intermediate noble metal concentrations in carbon (Cy) made it possible to find that the dependence of ße on Cy in case of gold desoprtion shows a clear extreme character. The value of the initial metal concentration in carbon therewith does not influence the character of the curve the inflection point of which is changed essentially at elevated process temperatures only. The revealed characteristic property, in the author's opinion can only be indicative of the change in the mechanism of gold desorption under autoclave desorption conditions. The assumed [Au(CN)(OH)]- type intermediate that has a higher diffusion coefficient in comparison with the adsorbed complex [Au(CN)2]- can be considered as an intermediate compound in the process of gold desorption."

Jan 1, 2003

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture. These equations are called geometric probability equations.Davy derived a geometric probability equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. This covariance can be used to measure the variance of the particle composition distribution of each mineral. The equation as presented by Davy requires textural information; however the equation was modified by Gay to be more directly applied to particle sections and linear intercepts. The variance obtained from applying this equation is fundamental to the binary stereological correction procedures developed by Gay and his colleagues; the covariance is fundamental to the multiphase stereological correction.Thus far, validation of both the binary and multiphase stereological correction has been achieved using numerical simulation. This paper shall present results comparing the covariance (and variance) estimates from Gay’s equation with actual three-dimensional information obtained from serially sectioning particles. This involved mounting a set of particles and continuously sectioning all particles uniformly so that the three dimensional structure of the particles could be obtained.The mineralogical data to which the equations described above were applied were derived from two individual size fractions from a hard-rock titanium deposit. The deposit contains a range of minerals and of mineral textures and the two size fractions selected were:"

Jan 1, 2003

This publication contains 10 papers presented at a symposium on ATRS systems in Charleston, WV, on June 23, 1983. Included are papers by MSHA Technical Support (Roof Control), West Virginia Institute of Technology, the Bureau of Mines, and seven roof bolter manufacturers and/or designers of ATRS systems. These papers summarize the most recent developments in ATRS technology and can serve as a guide to potential designers, developers, and users of ATRS systems.

Jan 1, 1985

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

The ability to optimise a concentrator from mill feed to final products requires a simulator which integrates comminution, classification and separation modelling. In order to model this range of processes, such a simulator must handle a variety of information about the ore. The AMIRA P9 project has developed a whole-of-concentrator simulation capability which brings together a texture-based model of mineral liberation, quantitative X-ray micro-tomography analysis to measure the inputs required by this model, and a multi-component simulator software framework. In the context of this approach, the term ?multi-component? implies the ability of the simulation to handle many particle properties simultaneously; for example size, composition, density, floatability etc. The simulation software framework provides the means to manage the flow of data around a circuit flowsheet, allowing each process model to access the information relevant to that particular model. A case study based on plant data from a gold-bearing pyrite concentrator is used to demonstrate the capabilities of the multi-component approach in simulating circuits which contain comminution and separation processes.

Feb 27, 2013

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009

By G J. Lyman, F S. Bourgeois

As the prices of metals slide, financial control of mineral processing operations becomes more and more important. Control of a mineral processing operation implies measurement of grades, recoveries and losses, with every effort being made to recover more product from the same feed. Shareholders become more concerned with the transparency of the operations and the corporate governance.There is only one way to achieve this and this is by sampling and making good use of the results of that sampling. Sampling systems that provide only 'rough' figures are not good enough. Similarly, a competitive position in the marketplace demands close control of product quality. Maximisation of product output demands that the product just meet the specification so that product yield is maximised. Decisions based on precise sampling results carry less risk that those based on imprecise results.This paper reports some recent advances in sampling theory that permit full quantification of sampling distributions, not just the sampling variance as has been possible in the past. These advances can be used together with simulation methods to tie down sampling precisions and develop calculations that quantify decision making risk when using the sampling results. A number of examples illustrate the use of the new advances and a final example indicates the development of risk analysis curves in the coupling of sampling precision to sale of a commodity.CITATION:Lyman, G J and Bourgeois, F S, 2015. Sampling, corporate governance and risk analysis, in Proceedings MetPlant 2015, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Bill Parnell

"Friction winders and double drum winders have been used in the vertical shaft mining industry for over 100 years. In that time, there have been many changes made in the electronic and mechanical fields of hoisting, but few changes made in the manufacturing and performance of steel wire rope, until recently.In the past ten years, with the advent of high polymer thermoplastics, the industry has seen some major advancements in steel wire rope. By incorporating a polymer with steel, improvement of rope life and reduction of costly maintenance downtime has been accomplished.IntroductionThe Williams Mine is Canada's largest gold producer with an annual production of some 500 000 ounces of gold from 2.2 million tonnes of ore. The Williams Mine is situated in the Hemlo area of northwestern Ontario, approximately 40 Ian east of the town of Marathon. It is operated by the Williams Operating Corporation which is owned equally by Teck Corporation and Homestake Canada Inc. It is one of three adjacent properties forming the Hemlo gold camp."

Jan 1, 1995

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Kagan Ozdemir

In the condition that drilling and blasting technique is inevitable depending on the rock mass and material characteristics on mining activities, the fragmentation rate and particle size distribution of the muckpile after blasting has important influences on the performance of subsequent mining activities such as loading, hauling, crushing, grinding etc. and the total costs of that mine. Drilling and blasting is an important step in this process chain and it's results such as fragmentation, muckpile shape and looseness, dilution, damage and rock softening effect the efficiency of downstream processes. There is an increasing body of blasting research indicating significant impacts in these downstream processes.

Jan 1, 2007

This backgrounds the methods, and technical terminology, of digital image processing techniques used to write out remote sensing imagery.

Jan 1, 1983

An examination of the Census of Fatal Occupational Injuries (CFOI) data for the period 1992-1995 shows that 659 fatalities occurred in the mining industry as defined by the SIC. Oil and gas accounted for slightly more than one-half of all fatalities (figure 1-1). The coal industry had the highest fatality rate for the 4-year period, with 35.6 deaths per 100,000 full-time workers, followed by metal (23.1 per 100,000), oil and gas (23.1 per 100,000), and nonmetal (20.1 per 100,000). The fatality rate for all U. S. industries during this same period was 5.1 per 100,000 full-time workers. Figure 1-2 compares the fatal injury rates by year for the four major industry sectors of mining to the fatality rate for all industries combined. Figure 1-3 compares age-specific fatality rates in the mining industry to those seen for U. S. industry as a whole. Fatality rates for all industries combined were lowest for young workers and steadily increased in relation to workers' ages. In the mining industry, fatality rates by age group show a U-shaped curve. Young workers under 20 years of age had the highest injury rate (54.6 per 100,000), followed by workers aged 20-24 (50.8 per 100,000) and workers over age 65 (37.7 per 100,000). Table 1-1 shows the distribution of injuries by type of injury event. The mining industry, in comparison with all industries, had a considerably larger proportion of fatalities classified as caught in or crushed by collapsing materials (9.1% and 1.9%, respectively) and fires and explosions (10.0% and 3.1%, respectively). Transportation events comprised the largest proportion of fatal injuries in both the mining industry and all industries. Within the mining industry only, transportation accounted for the largest proportion of fatalities in all mining sectors except coal. A more detailed examination of the transportation events within the mining industry showed that highway incidents (50.5%) were the most common, followed by nonhighway incidents (22.2%), pedestrian incidents (10.6%), and those incurred during rail, water, and air transport (15.7%). Incidents involving caught in or crushed by collapsing materials comprised a higher percentage of injuries in the coal and metal sectors, while fall-from-height incidents were more frequent in the oil and gas sector. The classification system used in CFOI for type of injury event is not compatible with any variables contained in the MSHA data; therefore, direct comparisons are not attempted. [ ]

Jan 5, 2000

By C. O. Karacan

Underground longwall mining of coal causes large scale disturbance of the surrounding rock mass. The disturbance can increase the rock mass permeability through a reduction on the stress as well as formation of new fractures in the rock. Methane gas contained in the disturbed rock mass can migrate towards the low pressure mine workings and present an explosion hazard. This paper describes the application of a finite difference program to develop a geomechanical model that predicts permeability changes within the rock mass. The calculated permeabilities are used as input to a reservoir simulator that models methane desorption from the coal matrix, methane release from the rock layers and flow towards the mine excavations. The model also considers the basic characteristics of the mine ventilation network. The geomechanical model uses empirical relationships between fracture permeability and stress to calculate permeability changes around a longwall face. The extent of rock failure is determined using a strain softening model that considers both rock matrix and bedding plane failure. The cave rock (gob) is modeled as a compressible, granulated material. The calculated horizontal and vertical permeabilities around the longwall face are averaged and used as one of the inputs to the reservoir model. The reservoir model was developed and calibrated against records of methane flow at a study mine in southwestern Pennsylvania. Good correlation between actual gas production and model outputs has been achieved. The modeling approach provides a basis for estimating methane inflow and optimizing control measures.

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920's through 1950's, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

On Nov 1, 2007 House Resolution 2262 ? The Hardrock Mining and Reclamation Act of 2007 ? was passed by the U.S. House by a vote of 244-166. HR-2262, among other things, would impose a 4-per-cent royalty on existing mines with commercial production and an 8-percent gross royalty on all new claims. Not surprisingly, this possible new law was one of the hottest topics of discussion at the Northwest Mining Association?s conference that this year returned to Spokane, WA for its 113th annual meeting on Dec. 3-7. More than 1,800 delegates attended the conference that was held under the banner theme of ?Mining ?. For today and tomorrow.? Northwest Mining Association executive director Laura Skaer was one of many speakers during the three-day conference to respond to the threat to the industry posed by HR-2262 with a presentation titled ?Potential changes to the 1872 Mining Law.? In the presentation that she first unveiled at the Alaska Miners Association?s convention and trade show on Nov. 8, Skaer laid out a comprehensive list of problems with HR-2262. In addition to the association?s obvious concerns about the proposed royalty, Skaer noted that the bill includes a mine veto provision that would allow the Secretary of the Interior the authority to deny an operations permit to a project if the secretary determines that the operation would cause undue degradation to public lands and resources. Potential massive withdrawals from mineral entry are also included in HR-2262. Among the lands that could be off limits to miners under HR-2262 are wilderness study areas, areas of environmental concern and 23.6 hm2 (58.5 million acres) identified as Roadless Rule. States, political subdivisions and Indian Tribes would also have more authority to withdraw lands, she said. To combat the proposed changes, Skaer made 10 trips to Washington D.C. on behalf of NWMA members in 2007. In her presentation at the annual meeting, she also objected to provisions that include no life-of-mine permits and uncertain permit renewals and new and duplicative environmental standards that she said are vague, ambiguous and inconsistent with current federal and state environmental laws. Debra W. Struhsacker, an environmental permitting and government relations consultant, also spoke on the issue of HR-2262 with a presentation titled ?The House mining law bill ? Rip van Winkle is back ? and he?s meaner than ever.?

Jan 1, 2008

By Stephen Hodgson, Ken Brouwer

September 2005, Northern Dynasty Mines announced the discovery of a new, high-grade deposit at its Pebble project in southwest Alaska. The product of insightful geological investigation, Pebble East, as it is now known, is quickly growing into one of the most significant copper deposits in the world. Preliminary analysis shows it could reduce the U.S. copper supply deficit by a third. The new deposit has also altered Northern Dynasty’s view of how Pebble should be developed. This article describes the Pebble project as it is currently understood and outlines the work planned for the next several years.

Jan 1, 2007